This patch fixes a long-standing isue with the port flow
control. Before this patch the retry mechanism was shared between all
different packet classes. As a result, a snoop response could get
stuck behind a request waiting for a retry, even if the send/recv
functions were split. This caused message-dependent deadlocks in
stress-test scenarios.
The patch splits the retry into one per packet (message) class. Thus,
sendTimingReq has a corresponding recvReqRetry, sendTimingResp has
recvRespRetry etc. Most of the changes to the code involve simply
clarifying what type of request a specific object was accepting.
The biggest change in functionality is in the cache downstream packet
queue, facing the memory. This queue was shared by requests and snoop
responses, and it is now split into two queues, each with their own
flow control, but the same physical MasterPort. These changes fixes
the previously seen deadlocks.
The ISA code sometimes stores 16-bit ASIDs as 8-bit unsigned integers
and has a couple of inverted checks that mask out the high 8 bits of
an ASID if 16-bit ASIDs have been /enabled/. This changeset fixes both
of those issues.
We curently use INTREG_X31 instead of INTREG_SPX when accessing the
stack pointer in GDB. gem5 normally uses INTREG_SPX to access the
stack pointer, which gets mapped to the stack pointer corresponding
(INTREG_SPn) to the current exception level. This changeset updates
the GDB interface to use SPX instead of X31 (which is always zero)
when transfering CPU state to gdb.
The remote GDB interface currently doesn't check if translations are
valid before reading memory. This causes a panic when GDB tries to
access unmapped memory (e.g., when getting a stack trace). There are
two reasons for this: 1) The function used to check for valid
translations (virtvalid()) doesn't work and panics on invalid
translations. 2) The method in the GDB interface used to test if a
translation is valid (RemoteGDB::acc) always returns true regardless
of the return from virtvalid().
This changeset fixes both of these issues.
This changeset moves the pseudo instructions used to signal unknown
instructions and unimplemented instructions to the same source files
as the decoder fault.
This patch clarifies the packet timings annotated
when going through a crossbar.
The old 'firstWordDelay' is replaced by 'headerDelay' that represents
the delay associated to the delivery of the header of the packet.
The old 'lastWordDelay' is replaced by 'payloadDelay' that represents
the delay needed to processing the payload of the packet.
For now the uses and values remain identical. However, going forward
the payloadDelay will be additive, and not include the
headerDelay. Follow-on patches will make the headerDelay capture the
pipeline latency incurred in the crossbar, whereas the payloadDelay
will capture the additional serialisation delay.
The TLB-related code is generally architecture dependent and should
live in the arch directory to signify that.
--HG--
rename : src/sim/BaseTLB.py => src/arch/generic/BaseTLB.py
rename : src/sim/tlb.cc => src/arch/generic/tlb.cc
rename : src/sim/tlb.hh => src/arch/generic/tlb.hh
While the IsFirstMicroop flag exists it was only occasionally used in the ARM
instructions that gem5 microOps and therefore couldn't be relied on to be correct.
This patch takes the final step in removing the src and dest fields in
the packet. These fields were rather confusing in that they only
remember a single multiplexing component, and pushed the
responsibility to the bridge and caches to store the fields in a
senderstate, thus effectively creating a stack. With the recent
changes to the crossbar response routing the crossbar is now
responsible without relying on the packet fields. Thus, these
variables are now unused and can be removed.
This patch fixes a minor issue in the X86 page table walker where it
ended up sending new request packets to the crossbar before the
response processing was finished (recvTimingResp is directly calling
sendTimingReq). Under certain conditions this caused the crossbar to
see illegal combinations of request/response overlap, in turn causing
problems with a slightly modified crossbar implementation.
This patch tidies up how we create and set the fields of a Request. In
essence it tries to use the constructor where possible (as opposed to
setPhys and setVirt), thus avoiding spreading the information across a
number of locations. In fact, setPhys is made private as part of this
patch, and a number of places where we callede setVirt instead uses
the appropriate constructor.
This patch corrects the FXSAVE and FXRSTOR Macroops. The actual code used for
saving/restore the FP registers is in the file but it was not used.
The FXSAVE and FXRSTOR instructions are used in the kernel for saving and
loading the state of the mmx,xmm and fpu registers.
This operation is triggered in FS by issuing a Device Not Available Fault. The
cr0 register has a TS flag that is set upon each context change. Every time a
task access any FP related register (SIMD as well) if the TS flag is set to
one, the device not available fault is issued. The kernel saves the current
state of the registers, and restore the previous state of the currently running
task.
Right now Gem5 lacks of this capability. the Device Not Available Fault is
never issued, leading to several problems when different threads share the same
CPU and SMT is not used. The PARSEC Ferret benchmark is an example of this
behavior.
In order to test this a hack in the atomic cpu code was done to detect if a
static instruction has any FP operands and the cr0 reg TS bit is set. This
check must be done in the ISA dependent code. But it seems to be tricky to
access the cr0 register while executing an instruction.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
That change enables CPUID bits for features that aren't implemented in gem5.
If a simulated system tries to use those features because it was told it
could, bad things can happen.
added ARM aarch64 unlinkat syscall support, modeled on other <xxx>at syscalls.
This gets all of the cpu2006 int workloads passing in SE mode on aarch64.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch implements the simd128 ADDSUBPD instruction for the x86 architecture.
Tested with a simple program in assembly language which executes the
instruction. Checked that different versions of the instruction are executed
by using the execution tracing option.
Committed by: Nilay Vaish <nilay@cs.wisc.edu
This patch adds table walker stats for:
- Walk events
- Instruction vs Data
- Page size histogram
- Wait time and service time histograms
- Pending requests histogram (per cycle) - measures dist. of L
(p(1..) = how often busy, p(0) = how often idle)
- Squashes, before starting and after completion
We currently don't handle unaligned PCs correctly. There is one check
for unaligned PCs in the TLB when running in aarch64 mode, but this
check does not cover cases where the CPU does not do a TLB lookup when
decoding an instruction (e.g., a branch stays within the same cache
line). Additionally, the Decoder class sometimes throws an assertion
for unaligned PCs which breaks speculation.
This changeset introduces a decoder fault bit field in the ExtMachInst
structure. This field can be used to signal a decoder failure. If set,
the decoder generates an internal gem5fault instruction instead of a
normal instruction. This instruction in turns either panics (fault
type PANIC), returns an PCAlignmentFault (fault type UNALIGNED,
aarch64) or PrefetchAbort (fault type UNALIGNED, aarch32).
The patch causes minor changes to the realview64 regressions, and a
stats bump will follow.
This patch adds support for filtering events in the PMU. In order to
do so, it updates the ISADevice base class to forward an ISA pointer
to ISA devices. This enables such devices to access the MiscReg file
to determine the current execution level.
The aarch64 system register decoder is currently not decoding
PMXEVTYPER_EL0 and PMCCFILTR_EL0 correctly. This changeset updates the
decoder so that they are decoded using the values in table C5-6 in ARM
DDI 0478A.c.
The new single stepping implementation for x86 doesn't rely on any ISA
specific properties or functionality. This change pulls out the per ISA
implementation of those functions and promotes the X86 implementation to the
base class.
One drawback of that implementation is that the CPU might stop on an
instruction twice if it's affected by both breakpoints and single stepping.
While that might be a little surprising, it's harmless and would only happen
under somewhat unlikely circumstances.
This stub should allow remote debugging of 32 bit and 64 bit targets. Single
stepping seems to work, as do breakpoints. If both breakpoints and single
stepping affect an instruction, gdb will stop at the instruction twice before
continuing. That's a little surprising, but is generally harmless.
Not all ISAs have 64 bit sized registers, so it's not always very convenient
to access the GDB register cache in 64 bit sized chunks. This change makes it
accessible in 8, 16, 32, or 64 bit chunks. The MIPS and ARM implementations
were working around that limitation by bundling and unbundling 32 bit values
into 64 bit values. That code has been removed.
Instead of counting the number of opcode bytes in an instruction and recording
each byte before the actual opcode, we can represent the path we took to get to
the actual opcode byte by using a type code. That has a couple of advantages.
First, we can disambiguate the properties of opcodes of the same length which
have different properties. Second, it reduces the amount of data stored in an
ExtMachInst, making them slightly easier/faster to create and process. This
also adds some flexibility as far as how different types of opcodes are
handled, which might come in handy if we decide to support VEX or XOP
instructions.
This change also adds tables to support properly decoding 3 byte opcodes.
Before we would fall off the end of some arrays, on top of the ambiguity
described above.
This change doesn't measureably affect performance on the twolf benchmark.
--HG--
rename : src/arch/x86/isa/decoder/three_byte_opcodes.isa => src/arch/x86/isa/decoder/three_byte_0f38_opcodes.isa
rename : src/arch/x86/isa/decoder/three_byte_opcodes.isa => src/arch/x86/isa/decoder/three_byte_0f3a_opcodes.isa
The values in a "bitfield" or in an ExtMachInst structure member may not be a
literal value, it might select from an arbitrary collection of options. Instead
of using the raw value of those constants in the decoder, it's easier to tell
what's going on if they can be referred to as a symbolic constant/enum.
To support that, the ISA description language is extended slightly so that in
addition to integer literals, the case value for decode blobs can also be a
string literal. It's up to the ISA author to ensure that the string evaluates
to a legal constant value when interpretted as C++.
This patch fixes a case where the Minor CPU can deadlock due to the lack
of a response to TLB request because of a bug in fault handling in the ARM
table walker.
TableWalker::processWalkWrapper is the scheduler-called wrapper which
handles deferred walks which calls to TableWalker::wait cannot immediately
process. The handling of faults generated by processWalk{AArch64,LPAE,}
calls in those two functions is is different. processWalkWrapper ignores
fault returns from processWalk... which can lead to ::finish not being
called on a translation.
This fix provides fault handling in processWalkWrapper similar to that
found in the leaf functions which BaseTLB::Translation::finish.
This patch adds uncacheable/cacheable and read-only/read-write attributes to
the map method of PageTableBase. It also modifies the constructor of TlbEntry
structs for all architectures to consider the new attributes.
This patch sets up low and high privilege code and data segments and places them
in the following order: cs low, ds low, ds, cs, in the GDT. Additionally, a
syscall and page fault handler for KvmCPU in SE mode are defined. The order of
the segment selectors in GDT is required in this manner for interrupt handling
to work properly. Segment initialization is done for all the thread
contexts.
This patch adds methods in KvmCPU model to handle KVM exits caused by syscall
instructions and page faults. These types of exits will be encountered if
KvmCPU is run in SE mode.
The data size used for actually writing the base value for the segment was the
default size, but really it should set the entire value without any possible
truncation.
The far pointer should be shifted right to get the selector value, not left.
Also, when calculating the width of the offset, the wrong register was used in
one spot.
The getRegArrayBit function extracts a bit from a series of registers which
are treated as a single large bit array. A previous change had modified the
logic which figured out which bit to extract from ">> 5" to "% 5" which seems
wrong, especially when other, similar functions were changed to use "% 32".
The value in EAX has an 8 bit field for the linear address size and one for
the physical address size when calling that function. A recent change
implemented it but returned 0xff for both of those fields. That implies that
linear and physical addresses are 255 bits wide which is wrong. When using the
KVM CPU model this causes an error, presumably because some of those bits are
actually reserved, or the CPU or kernel realizes 255 bits is a bad value.
This change makes those values 48.
Another churn to clean up undefined behaviour, mostly ARM, but some
parts also touching the generic part of the code base.
Most of the fixes are simply ensuring that proper intialisation. One
of the more subtle changes is the return type of the sign-extension,
which is changed to uint64_t. This is to avoid shifting negative
values (undefined behaviour) in the ISA code.
Mwait works as follows:
1. A cpu monitors an address of interest (monitor instruction)
2. A cpu calls mwait - this loads the cache line into that cpu's cache.
3. The cpu goes to sleep.
4. When another processor requests write permission for the line, it is
evicted from the sleeping cpu's cache. This eviction is forwarded to the
sleeping cpu, which then wakes up.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This changes the default ARM system to a Versatile Express-like system that supports
2GB of memory and PCI devices and updates the default kernels/file-systems for
AArch64 ARM systems (64-bit) to support up to 32GB of memory and PCI devices. Some
platforms that are no longer supported have been pruned from the configuration files.
In addition a set of 64-bit ARM regressions have been added to the regression system.
The checker can't verify timer registers, so it should just grab the version
from the executing CPU, otherwise it could get a larger value and diverge
execution.
The identifier SYS_getdents is not available on Mac OS X. Therefore, its use
results in compilation failure. It seems there is no straight forward way to
implement the system call getdents using readdir() or similar C functions.
Hence the commit 6709bbcf564d is being rolled back.
This patch fixes a few minor issues that caused link-time warnings
when using LTO, mainly for x86. The most important change is how the
syscall array is created. Previously gcc and clang would complain that
the declaration and definition types did not match. The organisation
is now changed to match how it is done for ARM, moving the code that
was previously in syscalls.cc into process.cc, and having a class
variable pointing to the static array.
With these changes, there are no longer any warnings using gcc 4.6.3
with LTO.
This patch takes quite a large step in transitioning from the ad-hoc
RefCountingPtr to the c++11 shared_ptr by adopting its use for all
Faults. There are no changes in behaviour, and the code modifications
are mostly just replacing "new" with "make_shared".
This patch makes the memory system ISA-agnostic by enabling the Ruby
Sequencer to dynamically determine if it has to do a store check. To
enable this check, the ISA is encoded as an enum, and the system
is able to provide the ISA to the Sequencer at run time.
--HG--
rename : src/arch/x86/insts/microldstop.hh => src/arch/x86/ldstflags.hh
This changeset adds probe points that can be used to implement PMU
counters for TLB stats. The following probes are supported:
* ArmISA::TLB::ppRefills / TLB Refills (TLB insertions)
This class implements a subset of the ARM PMU v3 specification as
described in the ARMv8 reference manual. It supports most of the
features of the PMU, however the following features are known to be
missing:
* Event filtering (e.g., from different privilege levels).
* Access controls (the PMU currently ignores the execution level).
* The chain counter (event no. 0x1E) is unimplemented.
The PMU itself does not implement any events, it merely provides an
interface for the configuration scripts to hook up probes that drive
events. Configuration scripts should call addEventProbe() to configure
custom events or high-level methods to configure architected
events. The Python implementation of addEventProbe() automatically
delays event type registration until after instantiation.
In order to support CPU switching and some combined counters (e.g.,
memory references synthesized from loads and stores), the PMU allows
multiple probes per event type. When creating a system that switches
between CPU models that share the same PMU, PMU events for all of the
CPU models can be registered with the PMU.
Kudos to Matt Horsnell for the initial gem5 implementation of the PMU.
This patch fixes the runtime errors highlighted by the undefined
behaviour sanitizer. In the end there were two issues. First, when
rotating an immediate, we ended up shifting an uint32_t by 32 in some
cases. This case is fixed by checking for a rotation by 0
positions. Second, the Mrc15 and Mcr15 are operating on an IntReg and
a MiscReg, but we used the type RegRegImmOp and passed a MiscRegIndex
as an IntRegIndex. This issue is resolved by introducing a
MiscRegRegImmOp and RegMiscRegImmOp with the appropriate types.
With these fixes there are no runtime errors identified for the full
ARM regressions.
This patch optimises the passing of StaticInstPtr by avoiding copying
the reference-counting pointer. This avoids first incrementing and
then decrementing the reference-counting pointer.
Fix a number few minor issues to please gcc 4.9.1. Removing the
'-fuse-linker-plugin' flag means no libraries are part of the LTO
process, but hopefully this is an acceptable loss, as the flag causes
issues on a lot of systems (only certain combinations of gcc, ld and
ar work).
activate(), suspend(), and halt() used on thread contexts had an optional
delay parameter. However this parameter was often ignored. Also, when used,
the delay was seemily arbitrarily set to 0 or 1 cycle (no other delays were
ever specified). This patch removes the delay parameter and 'Events'
associated with them across all ISAs and cores. Unused activate logic
is also removed.
This patch changes the name of the Bus classes to XBar to better
reflect the actual timing behaviour. The actual instances in the
config scripts are not renamed, and remain as e.g. iobus or membus.
As part of this renaming, the code has also been clean up slightly,
making use of range-based for loops and tidying up some comments. The
only changes outside the bus/crossbar code is due to the delay
variables in the packet.
--HG--
rename : src/mem/Bus.py => src/mem/XBar.py
rename : src/mem/coherent_bus.cc => src/mem/coherent_xbar.cc
rename : src/mem/coherent_bus.hh => src/mem/coherent_xbar.hh
rename : src/mem/noncoherent_bus.cc => src/mem/noncoherent_xbar.cc
rename : src/mem/noncoherent_bus.hh => src/mem/noncoherent_xbar.hh
rename : src/mem/bus.cc => src/mem/xbar.cc
rename : src/mem/bus.hh => src/mem/xbar.hh
This patch changes how faults are passed between methods in an attempt
to copy as few reference-counting pointer instances as possible. This
should avoid unecessary copies being created, contributing to the
increment/decrement of the reference counters.
This patch closes a number of space gaps in debug messages caused by
the incorrect use of line continuation within strings. (There's also
one consistency change to a similar, but correct, use of line
continuation)
Multiple instructions assume only 32-bit load operations are available,
this patch increases load sizes to 64-bit or 128-bit for many load pair and
load multiple instructions.
The o3 cpu relies upon instructions that suspend a thread context being
flagged as "IsQuiesce". If they are not, unpredictable behavior can occur.
This patch fixes that for the x86 ISA.
Neon memory ops that operate on multiple registers currently have very poor
performance because of interleave/deinterleave micro-ops.
This patch marks the deinterleave/interleave micro-ops as "No_OpClass" such
that they take minumum cycles to execute and are never resource constrained.
Additionaly the micro-ops over-read registers. Although one form may need
to read up to 20 sources, not all do. This adds in new forms so false
dependencies are not modeled. Instructions read their minimum number of
sources.
Analogous to ee049bf (for x86). Requires a bump of the checkpoint version
and corresponding upgrader code to move the condition code register values
to the new register file.
isa_parser.py guesses the OpClass if none were given based upon the StaticInst
flags. The existing code does not take into account optionally set flags.
This code hoists the setting of optional flags so OpClass is properly assigned.
We currently generate and compile one version of the ISA code per CPU
model. This is obviously wasting a lot of resources at compile
time. This changeset factors out the interface into a separate
ExecContext class, which also serves as documentation for the
interface between CPUs and the ISA code. While doing so, this
changeset also fixes up interface inconsistencies between the
different CPU models.
The main argument for using one set of ISA code per CPU model has
always been performance as this avoid indirect branches in the
generated code. However, this argument does not hold water. Booting
Linux on a simulated ARM system running in atomic mode
(opt/10.linux-boot/realview-simple-atomic) is actually 2% faster
(compiled using clang 3.4) after applying this patch. Additionally,
compilation time is decreased by 35%.
This patch prunes unused values, and also unifies how the values are
defined (not using an enum for ALPHA), aligning the use of int vs Addr
etc.
The patch also removes the duplication of PageBytes/PageShift and
VMPageSize/LogVMPageSize. For all ISAs the two pairs had identical
values and the latter has been removed.
When passed from a configuration script with a hexadecimal value (like
"0x80000000"), gem5 would error out. This is because it would call
"toMemorySize" which requires the argument to end with a size specifier (like
1MB, etc).
This modification makes it so raw hex values can be passed through Addr
parameters from the configuration scripts.
This patch fixes the hash operator used for ARM ExtMachInst, which
incorrectly was still using uint32_t. Instead of changing it to
uint64_t it is not using the underlying data type of the BitUnion.
This patch enables the use of page tables that are stored in system memory
and respect x86 specification, in SE mode. It defines an architectural
page table for x86 as a MultiLevelPageTable class and puts a placeholder
class for other ISAs page tables, giving the possibility for future
implementation.
We currently use our own home-baked support for type-safe variadic
functions. This is confusing and somewhat limited (e.g., cprintf only
supports a limited number of arguments). This changeset converts all
uses of our internal varargs support to use C++11 variadic macros.
The order of the MSB and LSB bit of the mm field in the PSTATE union
is wrong. Any access to this field will currently be ignored and reads
will always return zero. This patch fixes the ordering so it is <MSB,
LSB> instead of <LSB, MSB>.
Some newer binaries compiled for Versatile Express TC2 contain access
to implementation specific L2MERRSR registers. This causes an infinite
loop of undefined exceptions. This patch changes the behavior to "warn
not fail" to keep the workloads going.
Certain versions of clang complain about unused private members if
they are not used. This changeset removes such members from the
MIPS-specific classes to silence the warning.
Certain versions of clang complain about unused private members if
they are not used. This changeset removes such members from the
POWER-specific ProcessInfo struct to silence the warning.
Adds DVFS capabilities to gem5, by allowing users to specify lists for
frequencies and voltages in SrcClockDomains and VoltageDomains respectively.
A separate component, DVFSHandler, provides a small interface to change
operating points of the associated domains.
Clock domains will be linked to voltage domains and thus allow separate clock,
but shared voltage lines.
Currently all the valid performance-level updates are performed with a fixed
transition latency as specified for the domain.
Config file example:
...
vd = VoltageDomain(voltage = ['1V','0.95V','0.90V','0.85V'])
tsys.cluster1.clk_domain.clock = ['1GHz','700MHz','400MHz','230MHz']
tsys.cluster2.clk_domain.clock = ['1GHz','700MHz','400MHz','230MHz']
tsys.cluster1.clk_domain.domain_id = 0
tsys.cluster2.clk_domain.domain_id = 1
tsys.cluster1.clk_domain.voltage_domain = vd
tsys.cluster2.clk_domain.voltage_domain = vd
tsys.dvfs_handler.domains = [tsys.cluster1.clk_domain,
tsys.cluster2.clk_domain]
tsys.dvfs_handler.enable = True
In a cycle, we could see a R and W requests corresponding to the same
page walk being sent to the memory. During the cycle that assertion
happens, we have 2 responses corresponding to the R and W above. We
also have a 'read' variable to keep track of the inflight Read
request, this gets reset to NULL right after we send out any R
request; and gets set to the next R in the page walk when a response
comes back.
The issue we are seeing here is when we get a response for W request,
assert(!read) fires because we got a response for R request right
before this, hence we set 'read' to NOT NULL value, pointing to the
next R request in the pagewalk!
This work was done while Binh was an intern at AMD Research.
Using '== true' in a boolean expression is totally redundant,
and using '== false' is pretty verbose (and arguably less
readable in most cases) compared to '!'.
It's somewhat of a pet peeve, perhaps, but I had some time
waiting for some tests to run and decided to clean these up.
Unfortunately, SLICC appears not to have the '!' operator,
so I had to leave the '== false' tests in the SLICC code.
This patch adds a the member function StaticInst::printFlags to allow all
of an instruction's flags to be printed without using the individual
is... member functions or resorting to exposing the 'flags' vector
It also replaces the enum definition StaticInst::Flags with a
Python-generated enumeration and adds to the enum generation mechanism
in src/python/m5/params.py to allow Enums to be placed in namespaces
other than Enums or, alternatively, in wrapper structs allowing them to
be inherited by other classes (so populating that class's name-space
with the enumeration element names).
This patch encompasses several interrelated and interdependent changes
to the ISA generation step. The end goal is to reduce the size of the
generated compilation units for instruction execution and decoding so
that batch compilation can proceed with all CPUs active without
exhausting physical memory.
The ISA parser (src/arch/isa_parser.py) has been improved so that it can
accept 'split [output_type];' directives at the top level of the grammar
and 'split(output_type)' python calls within 'exec {{ ... }}' blocks.
This has the effect of "splitting" the files into smaller compilation
units. I use air-quotes around "splitting" because the files themselves
are not split, but preprocessing directives are inserted to have the same
effect.
Architecturally, the ISA parser has had some changes in how it works.
In general, it emits code sooner. It doesn't generate per-CPU files,
and instead defers to the C preprocessor to create the duplicate copies
for each CPU type. Likewise there are more files emitted and the C
preprocessor does more substitution that used to be done by the ISA parser.
Finally, the build system (SCons) needs to be able to cope with a
dynamic list of source files coming out of the ISA parser. The changes
to the SCons{cript,truct} files support this. In broad strokes, the
targets requested on the command line are hidden from SCons until all
the build dependencies are determined, otherwise it would try, realize
it can't reach the goal, and terminate in failure. Since build steps
(i.e. running the ISA parser) must be taken to determine the file list,
several new build stages have been inserted at the very start of the
build. First, the build dependencies from the ISA parser will be emitted
to arch/$ISA/generated/inc.d, which is then read by a new SCons builder
to finalize the dependencies. (Once inc.d exists, the ISA parser will not
need to be run to complete this step.) Once the dependencies are known,
the 'Environments' are made by the makeEnv() function. This function used
to be called before the build began but now happens during the build.
It is easy to see that this step is quite slow; this is a known issue
and it's important to realize that it was already slow, but there was
no obvious cause to attribute it to since nothing was displayed to the
terminal. Since new steps that used to be performed serially are now in a
potentially-parallel build phase, the pathname handling in the SCons scripts
has been tightened up to deal with chdir() race conditions. In general,
pathnames are computed earlier and more likely to be stored, passed around,
and processed as absolute paths rather than relative paths. In the end,
some of these issues had to be fixed by inserting serializing dependencies
in the build.
Minor note:
For the null ISA, we just provide a dummy inc.d so SCons is never
compelled to try to generate it. While it seems slightly wrong to have
anything in src/arch/*/generated (i.e. a non-generated 'generated' file),
it's by far the simplest solution.
The ARM TLBs have a bootUncacheability flag used to make some loads
and stores become uncacheable when booting in FS mode. Later the
flag is cleared to let those loads and stores operate as normal. When
doing a takeOverFrom(), this flag's state is not preserved and is
momentarily reset until the CPSR is touched. On single core runs this
is a non-issue. On multi-core runs this can lead to crashes on the O3
CPU model from the following series of events:
1) takeOverFrom executed to switch from Atomic -> O3
2) All bootUncacheability flags are reset to true
3) Core2 tries to execute a load covered by bootUncacheability, it
is flagged as uncacheable
4) Core2's load needs to replay due to a pipeline flush
3) Core1 core does an action on CPSR
4) The handling code for CPSR then checks all other cores
to determine if bootUncacheability can be set to false
5) Asynchronously set bootUncacheability on all cores to false
6) Core2 replays load previously set as uncacheable and notices
it is now flagged as cacheable, leads to a panic.
This patch implements takeOverFrom() functionality for the ARM TLBs
to preserve flag values when switching from atomic -> detailed.
Allow the specification of a socket ID for every core that is reflected in the
MPIDR field in ARM systems. This allows studying multi-socket / cluster
systems with ARM CPUs.
Unimplemented miscregs for the generic timer were guarded by panics
in arm/isa.cc which can be tripped by the O3 model if it speculatively
executes a wrong path containing a mrs instruction with a bad miscreg
index. These registers were flagged as implemented and accessible.
This patch changes the miscreg info bit vector to flag them as
unimplemented and inaccessible. In this case, and UndefinedInst
fault will be generated if the register access is not trapped
by a hypervisor.
With (upcoming) separate compilation, they are useless. Only
link-time optimization could re-inline them, but ideally
feedback-directed optimization would choose to do so only for
profitable (i.e. common) instructions.
The MicroMemOp class generates the disassembly for both integer
and floating point instructions, but it would always print its
first operand as an integer register without considering that the
op may be a floating instruction in which case a float register
should be displayed instead.
There were several sections of the m5ops code which were
essentially copy/pasted versions of the 32-bit code. The
problem is that some of these didn't account fo4 64-bit
registers leading to arguments being in the wrong registers.
This patch addresses the args for readfile64, writefile64,
and addsymbol64 -- all of which seemed to suffer from a
similar set of problems when moving to 64-bit.
This changeset adds support for INIT and STARTUP IPI handling. We
currently handle both of these interrupts in gem5 and transfer the
state to KVM. Since we do not have a BIOS loaded, we pretend that the
INIT interrupt suspends the CPU after reset.
--HG--
extra : rebase_source : 7f3b25f3801d68f668b6cd91eaf50d6f48ee2a6a
The table walker code currently accounts for two types of walks,
Atomic and Timing, and treats them differently. Atomic walks keep a
single instance of WalkerState around for all walks to use in
currState. Timing mode keeps a queue of in-flight WalkerStates and
maintains currState as NULL between walks.
If a functional walk is done during Timing mode, it is treated as an
atomic walk and either creates a persistent WalkerState if in between
Timing walks, or stomps an existing currState for an in-progress
Timing walk.
This patch distinguishes functional walks as being able to exist at
any time and sets up a temporary WalkerState for its exclusive use and
then cleans up when finished, leaving any in progress Atomic or Timing
walks undisturbed.
Small fix for a warning that prevents compilation with gcc 4.8.1 due
to detecting that a variable might be uninitialised. The fix is to
assign a safe default.
The TSL/LDT & TR/TSS segments didn't contain valid attributes. This
caused problems when transfering the state into KVM where invalid
state is a no-go. Fixup the attributes with values from AMD's
architecture programmer's manual.
A copyRegs() function is added to MIPS utilities
to copy architectural state from the old CPU to
the new CPU during fast-forwarding. This
addition alone enables fast-forwarding for the
o3 cpu model running MIPS.
The patch also adds takeOverFrom() and
drainResume() functions to the InOrderCPU to
enable it to take over from another CPU. This
change enables fast-forwarding for the inorder
cpu model running MIPS, but not for Alpha.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Changeset 7274310be1bb (isa: clean up register constants) increased
the value of NumFloatRegs, which triggered a bug in
X86ISA::copyRegs(). This bug is caused by the x87 stack being copied
twice since register indexes past NUM_FLOATREGS are mapped into the
x87 stack relative to the top of the stack, which is undefined when
the copy takes place.
This changeset updates the copyRegs() function to use access registers
using the non-flattening interface, which guarantees that undesirable
register folding does not happen.
The getRFlags and setRFlags utility functions were not updated
correctly when condition registers were separated into their own
register class. This lead to incorrect state transfer in calls from
kvm into the simulator (e.g., m5 readfile ended up in an infinite
loop) and when switching CPUs. This patch makes these utility
functions use getCCReg and setCCReg instead of getIntReg and setIntReg
which read and write the integer registers.
Reviewed-by: Andreas Sandberg <andreas@sandberg.pp.se>
Note: AArch64 and AArch32 interworking is not supported. If you use an AArch64
kernel you are restricted to AArch64 user-mode binaries. This will be addressed
in a later patch.
Note: Virtualization is only supported in AArch32 mode. This will also be fixed
in a later patch.
Contributors:
Giacomo Gabrielli (TrustZone, LPAE, system-level AArch64, AArch64 NEON, validation)
Thomas Grocutt (AArch32 Virtualization, AArch64 FP, validation)
Mbou Eyole (AArch64 NEON, validation)
Ali Saidi (AArch64 Linux support, code integration, validation)
Edmund Grimley-Evans (AArch64 FP)
William Wang (AArch64 Linux support)
Rene De Jong (AArch64 Linux support, performance opt.)
Matt Horsnell (AArch64 MP, validation)
Matt Evans (device models, code integration, validation)
Chris Adeniyi-Jones (AArch64 syscall-emulation)
Prakash Ramrakhyani (validation)
Dam Sunwoo (validation)
Chander Sudanthi (validation)
Stephan Diestelhorst (validation)
Andreas Hansson (code integration, performance opt.)
Eric Van Hensbergen (performance opt.)
Gabe Black
With ARMv8 support the same misc register id results in accessing different
registers depending on the current mode of the processor. This patch adds
the same orthogonality to the misc register file as the others (int, float, cc).
For all the othre ISAs this is currently a null-implementation.
Additionally, a system variable is added to all the ISA objects.
This patch add support for generating wake-up events in the CPU when an address
that is currently in the exclusive state is hit by a snoop. This mechanism is required
for ARMv8 multi-processor support.
Previously we were casting the result type to the the memory type which
is incorrect for things like dual-memory operations which still return a
single result.
This patch enables tracking of cache occupancy per thread along with
ages (in buckets) per cache blocks. Cache occupancy stats are
recalculated on each stat dump.
This patch fixes a memory leak in the table walker, by ensuring that
the sender state is deleted again if the request packet cannot be
successfully sent.
In mips architecture, floating point convert instructions use the
FloatConvertOp format defined in src/arch/mips/isa/formats/fp.isa. The type
of the operands in the ISA description file (_sw for signed word, or _sf for
signed float, etc.) is used to create a type for the operand in C++. Then the
operand is converted using the fpConvert() function in src/arch/mips/utility.cc.
If we are converting from a word to a float, and we want to convert 0xffffffff,
we expect -1 to be passed into fpConvert(). Instead, we see MAX_INT passed in.
Then fpConvert() converts _val_ to MAX_INT in single-precision floating point,
and we get the wrong value.
To fix it, the signs of the convert operands are being changed from unsigned to
signed in the MIPS ISA description.
Then, the FloatConvertOp format is being changed to insert a int32_t into the
C++ code instead of a uint32_t.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Thumb2 ARM kernels may access the TEEHBR via thumbee_notifier
in arch/arm/kernel/thumbee.c. The Linux kernel code just seems
to be saving and restoring the register. This patch adds support
for the TEEHBR cp14 register. Note, this may be a special case
when restoring from an image that was run on a system that
supports ThumbEE.
Convert condition code registers from being specialized
("pseudo") integer registers to using the recently
added CC register class.
Nilay Vaish also contributed to this patch.
Make these names more meaningful.
Specifically, made these substitutions:
s/FP_Base_DepTag/FP_Reg_Base/g;
s/Ctrl_Base_DepTag/Misc_Reg_Base/g;
s/Max_DepTag/Max_Reg_Index/g;
Clean up and add some consistency to the *_Base_DepTag
constants as well as some related register constants:
- Get rid of NumMiscArchRegs, TotalArchRegs, and TotalDataRegs
since they're never used and not always defined
- Set FP_Base_DepTag = NumIntRegs when possible (i.e.,
every case except x86)
- Set Ctrl_Base_DepTag = FP_Base_DepTag + NumFloatRegs
(this was true before, but wasn't always expressed
that way)
- Drastically reduce the number of arbitrary constants
appearing in these calculations
Move from a poorly documented scheme where the mapping
of unified architectural register indices to register
classes is hardcoded all over to one where there's an
enum for the register classes and a function that
encapsulates the mapping.
ASI_BITS in the Request object were originally used to store a memory
request's ASI on SPARC. This is not the case any more since other ISAs
use the ASI bits to store architecture-dependent information. This
changeset renames the ASI_BITS to ARCH_BITS which better describes
their use. Additionally, the getAsi() accessor is renamed to
getArchFlags().
Using address bit 63 to identify generic IPRs caused problems on
SPARC, where IPRs are heavily used. This changeset redefines how
generic IPRs are identified. Instead of using bit 63, we now use a
separate flag (GENERIC_IPR) a memory request.
In order to support m5ops in virtualized environments, we need to use
a memory mapped interface. This changeset adds support for that by
reserving 0xFFFF0000-0xFFFFFFFF and mapping those to the generic IPR
interface for m5ops. The mapping is done in the
X86ISA::TLB::finalizePhysical() which means that it just works for all
of the CPU models, including virtualized ones.
In order to support m5ops on virtualized CPUs, we need to either
intercept hypercall instructions or provide a memory mapped m5ops
interface. Since KVM does not normally pass the results of hypercalls
to userspace, which makes that method unfeasible. This changeset
introduces support for m5ops using memory mapped mmapped IPRs. This is
implemented by adding a class of "generic" IPRs which are handled by
architecture-independent code. Such IPRs always have bit 63 set and
are handled by handleGenericIprRead() and
handleGenericIprWrite(). Platform specific impementations of
handleIprRead and handleIprWrite should use
GenericISA::isGenericIprAccess to determine if an IPR address should
be handled by the generic code instead of the architecture-specific
code. Platforms that don't need their own IPR support can reuse
GenericISA::handleIprRead() and GenericISA::handleIprWrite().
The x87 FPU supports three floating point formats: 32-bit, 64-bit, and
80-bit floats. The current gem5 implementation supports 32-bit and
64-bit floats, but only works correctly for 64-bit floats. This
changeset fixes the 32-bit float handling by correctly loading and
rounding (using truncation) 32-bit floats instead of simply truncating
the bit pattern.
80-bit floats are loaded by first loading the 80-bits of the float to
two temporary integer registers. A micro-op (cvtint_fp80) then
converts the contents of the two integer registers to the internal FP
representation (double). Similarly, when storing an 80-bit float,
there are two conversion routines (ctvfp80h_int and cvtfp80l_int) that
convert an internal FP register to 80-bit and stores the upper 64-bits
or lower 32-bits to an integer register, which is the written to
memory using normal integer stores.
X87 store instructions typically loads and pops the top value of the
stack and stores it in memory. The current implementation pops the
stack at the same time as the floating point value is loaded to a
temporary register. This will corrupt the state of the x87 stack if
the store fails. This changeset introduces a pop87 micro-instruction
that pops the stack and uses this instruction in the affected
macro-instructions to pop the stack after storing the value to memory.
The x87 FPU on x86 supports extended floating point. We currently
handle all floating point on x86 as double and don't support 80-bit
loads/stores. This changeset add a utility function to load and
convert 80-bit floats to doubles (loadFloat80) and another function to
store doubles as 80-bit floats (storeFloat80). Both functions use
libfputils to do the conversion in software. The functions are
currently not used, but are required to handle floating point in KVM
and to properly support all x87 loads/stores.
This changeset adds the convX87XTagsToTags() and convX87TagsToXTags()
which convert between the tag formats in the FTW register and the
format used in the xsave area. The conversion from to the x87 FTW
representation is currently loses some information since it does not
reconstruct the valid/zero/special flags which are not included in the
xsave representation.
In order to support hardware virtualization, we need to be able to
check if there are any interrupts pending irregardless of the
rflags.intf value. This changeset adds the checkInterruptsRaw() method
to the x86 interrupt control. It returns true if there are pending
interrupts that can be delivered as soon as the CPU is ready for
interrupt delivery.
This patch makes it possible to once again build gem5 without any
ISA. The main purpose is to enable work around the interconnect and
memory system without having to build any CPU models or device models.
The regress script is updated to include the NULL ISA target. Currently
no regressions make use of it, but all the testers could (and perhaps
should) transition to it.
--HG--
rename : build_opts/NOISA => build_opts/NULL
rename : src/arch/noisa/SConsopts => src/arch/null/SConsopts
rename : src/arch/noisa/cpu_dummy.hh => src/arch/null/cpu_dummy.hh
rename : src/cpu/intr_control.cc => src/cpu/intr_control_noisa.cc
This patch moves the system virtual port proxy to the Alpha system
only to make the resurrection of the NOISA slightly less
painful. Alpha is the only ISA that is actually using it.
This patch adds a check to the quiesce operation to ensure that the
CPU does not suspend itself when there are unmasked interrupts
pending. Without this patch there are corner cases when the CPU gets
an interrupt before the quiesce is executed and then never wakes up
again.
This patch adds checkpointing support to x86 tlb. It upgrades the
cpt_upgrader.py script so that previously created checkpoints can
be updated. It moves the checkpoint version to 6.
This patch removes the notion of a peer block size and instead sets
the cache line size on the system level.
Previously the size was set per cache, and communicated through the
interconnect. There were plenty checks to ensure that everyone had the
same size specified, and these checks are now removed. Another benefit
that is not yet harnessed is that the cache line size is now known at
construction time, rather than after the port binding. Hence, the
block size can be locally stored and does not have to be queried every
time it is used.
A follow-on patch updates the configuration scripts accordingly.
Instead of relying on derived classes explicitly assigning
to the BasicPioDevice pioSize field, require them to pass
a size value in to the constructor.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
PciDev and IntDev stuck out as the only device classes that
ended in 'Dev' rather than 'Device'. This patch takes care
of that inconsistency.
Note that you may need to delete pre-existing files matching
build/*/python/m5/internal/param_* as scons does not pick up
indirect dependencies on imported python modules when generating
params, and the PciDev -> PciDevice rename takes place in a
file (dev/Device.py) that gets imported quite a bit.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
A couple of devices that have single fixed memory mapped regions
were not derived from BasicPioDevice, when that's exactly
the functionality that BasicPioDevice provides. This patch
gets rid of a little bit of redundant code by making those
devices actually do so.
Also fixed the weird case of X86ISA::Interrupts, where
the class already did derive from BasicPioDevice but
didn't actually use all the features it could have.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch adds the notion of source- and derived-clock domains to the
ClockedObjects. As such, all clock information is moved to the clock
domain, and the ClockedObjects are grouped into domains.
The clock domains are either source domains, with a specific clock
period, or derived domains that have a parent domain and a divider
(potentially chained). For piece of logic that runs at a derived clock
(a ratio of the clock its parent is running at) the necessary derived
clock domain is created from its corresponding parent clock
domain. For now, the derived clock domain only supports a divider,
thus ensuring a lower speed compared to its parent. Multiplier
functionality implies a PLL logic that has not been modelled yet
(create a separate clock instead).
The clock domains should be used as a mechanism to provide a
controllable clock source that affects clock for every clocked object
lying beneath it. The clock of the domain can (in a future patch) be
controlled by a handler responsible for dynamic frequency scaling of
the respective clock domains.
All the config scripts have been retro-fitted with clock domains. For
the System a default SrcClockDomain is created. For CPUs that run at a
different speed than the system, there is a seperate clock domain
created. This domain incorporates the CPU and the associated
caches. As before, Ruby runs under its own clock domain.
The clock period of all domains are pre-computed, such that no virtual
functions or multiplications are needed when calling
clockPeriod. Instead, the clock period is pre-computed when any
changes occur. For this to be possible, each clock domain tracks its
children.
The current implementation of the x87 never updates the x87 tag
word. This is currently not a big issue since the simulated x87 never
checks for stack overflows, however this becomes an issue when
switching between a virtualized CPU and a simulated CPU. This
changeset adds support, which is enabled by default, for updating the
tag register to every floating point microop that updates the stack
top using the spm mechanism.
The new tag words is generated by the helper function
X86ISA::genX87Tags(). This function is currently limited to flagging a
stack position as valid or invalid and does not try to distinguish
between the valid, zero, and special states.
This changeset actually fixes two issues:
* The lfpimm instruction didn't work correctly when applied to a
floating point constant (it did work for integers containing the
bit string representation of a constant) since it used
reinterpret_cast to convert a double to a uint64_t. This caused a
compilation error, at least, in gcc 4.6.3.
* The instructions loading floating point constants in the x87
processor didn't work correctly since they just stored a truncated
integer instead of a double in the floating point register. This
changeset fixes the old microcode by using lfpimm instruction
instead of the limm instructions.
The current implementation of fprem simply does an fmod and doesn't
simulate any of the iterative behavior in a real fprem. This isn't
normally a problem, however, it can lead to problems when switching
between CPU models. If switching from a real CPU in the middle of an
fprem loop to a simulated CPU, the output of the fprem loop becomes
correupted. This changeset changes the fprem implementation to work
like the one on real hardware.
The rflags register is spread across several different registers. Most
of the flags are stored in MISCREG_RFLAGS, but some are stored in
microcode registers. When accessing RFLAGS, we need to reconstruct it
from these registers. This changeset adds two functions,
X86ISA::getRFlags() and X86ISA::setRFlags(), that take care of this
magic.
This changeset fixes two problems in the FABS and FCHS
implementation. First, the ISA parser expects the assignment in
flag_code to be a pure assignment and not an and-assignment, which
leads to the isa_parser omitting the misc reg update. Second, the FCHS
and FABS macro-ops don't set the SetStatus flag, which means that the
default micro-op version, which doesn't update FSW, is executed.
The TSC value stored in MISCREG_TSC is actually just an offset from
the current CPU cycle to the actual TSC value. Writes with
side-effects to the TSC subtract the current cycle count before
storing the new value, while reads add the current cycle count. When
switching CPUs, the current value is copied without side-effects. This
works as long as the source and the destination CPUs have the same
clock frequencies. The TSC will jump, sometimes backwards, if they
have different clock frequencies. Most OSes assume the TSC to be
monotonic and break when this happens.
This changeset makes sure that the TSC is copied with side-effects to
ensure that the offset is updated to match the new CPU.
in the TLB
Some architectures (currently only x86) require some fixing-up of
physical addresses after a normal address translation. This is usually
to remap devices such as the APIC, but could be used for other memory
mapped devices as well. When running the CPU in a using hardware
virtualization, we still need to do these address fix-ups before
inserting the request into the memory system. This patch moves this
patch allows that code to be used by such CPUs without doing full
address translations.
This is the x86 version of the ARM changeset baa17ba80e06. In case an
instruction has been squashed by the o3 cpu, this patch allows page
table walker to avoid carrying out a pending translation that the
instruction requested for.
Currently call and return instructions are marked as IsCall and IsReturn. Thus, the
branch predictor does not use RAS for these instructions. Similarly, the number of
function calls that took place is recorded as 0. This patch marks these instructions
as they should be.
Currently all the integer microops are marked as IntAluOp and the floating
point microops are marked as FloatAddOp. This patch adds support for marking
different microops differently. Now IntMultOp, IntDivOp, FloatDivOp,
FloatMultOp, FloatCvtOp, FloatSqrtOp classes will be used as well. This will
help in providing different latencies for different op class.
The vsyscall address for gettimeofday is 0xffffffffff600000ul. The offset
therefore should be 0x0 instead of 0x410. This can be cross checked with
the file sysdeps/unix/sysv/linux/x86_64/gettimeofday.c in source of glibc.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
The 'lret' instruction reloads instruction pointer and code segment from the
stack and then pops them. But the popping part is missing from the current
implementation. This caused incorrect behavior in some code related to the
Fiasco OS. Microops are being added to rectify the behavior of the instruction.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Add the method checkRaw to ArmISA::Interrupts. This method can be used
to query the raw state (ignoring CPSR masks) of an interrupt. It is
primarily intended for hardware virtualized CPUs.
Add the options 'panic_on_panic' and 'panic_on_oops' to the
LinuxArmSystem SimObject. When these option are enabled, the simulator
panics when the guest kernel panics or oopses. Enable panic on panic
and panic on oops in ARM-based test cases.
This changeset adds support for forwarding arguments to the PC
event constructors to following methods:
addKernelFuncEvent
addFuncEvent
Additionally, this changeset adds the following helper method to the
System base class:
addFuncEventOrPanic - Hook a PCEvent to a symbol, panic on failure.
addKernelFuncEventOrPanic - Hook a PCEvent to a kernel symbol, panic
on failure.
System implementations have been updated to use the new functionality
where appropriate.
This patch adds a missing flag to the ldr_ret_uop microop instruction.
The flag is added when the instruction is used, not directly in the
constructor of the instruction.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>"
It is possible that operating system wants to shutdown the
lapic timer by writing timer's initial count to 0. This patch
adds a check that the timer event is only scheduled if the
count is 0.
The patch also converts few of the panics related to the keyboard
to warnings since we are any way not interested in simulating the
keyboard.
This patch fixes an issue related to the table walker recycling
packets that still have a bus delay that is not accounted for. For
now, we simply ignore the values and reset them to zero.
This patch fixes the warnings that clang3.2svn emit due to the "-Wall"
flag. There is one case of an uninitialised value in the ARM neon ISA
description, and then a whole range of unused private fields that are
pruned.
A derived function with a different signature than a base class
function will result in the base class function of the same name being
hidden. The parameter list and return type for the member function in
the derived class must match those of the member function in the base
class, otherwise the function in the derived class will hide the
function in the base class and no polymorphic behaviour will occur.
This patch addresses these warnings by ensuring a unique function name
to avoid (unintentionally) hiding any functions.
This patch address the most important name shadowing warnings (as
produced when using gcc/clang with -Wshadow). There are many
locations where constructor parameters and function parameters shadow
local variables, but these are left unchanged.
This patch moves the 16x APIC clock divider to the Python code to
avoid the post-instantiation modifications to the clock. The x86 APIC
was the only object setting the clock after creation time and this
required some custom functionality and configuration. With this patch,
the clock multiplier is moved to the Python code and the objects are
instantiated with the appropriate clock.
This patch adds a predecessor field to the SenderState base class to
make the process of linking them up more uniform, and enable a
traversal of the stack without knowing the specific type of the
subclasses.
There are a number of simplifications done as part of changing the
SenderState, particularly in the RubyTest.
If multiple memory operations to the same page are miss the TLB they are
all inserted into the page table queue and before this change could result
in multiple uncessesary walks as well as duplicate enteries being inserted
into the TLB.
Virtualized CPUs and the fastmem mode of the atomic CPU require direct
access to physical memory. We currently require caches to be disabled
when using them to prevent chaos. This is not ideal when switching
between hardware virutalized CPUs and other CPU models as it would
require a configuration change on each switch. This changeset
introduces a new version of the atomic memory mode,
'atomic_noncaching', where memory accesses are inserted into the
memory system as atomic accesses, but bypass caches.
To make memory mode tests cleaner, the following methods are added to
the System class:
* isAtomicMode() -- True if the memory mode is 'atomic' or 'direct'.
* isTimingMode() -- True if the memory mode is 'timing'.
* bypassCaches() -- True if caches should be bypassed.
The old getMemoryMode() and setMemoryMode() methods should never be
used from the C++ world anymore.
The explict tests in the follwing fp comparison operations were
incorrect as they checked for only signaling NaNs and not quite-NaNs
as well. When compiled with gcc, the comparison generates a fp exception
that causes the FE_INVALID flag to be set and we check for it, so even
though the check was incorrect, the correct exception was set. With clang
this behavior seems to not occur. The checks are updated to test for nans and
the behavior is now correct with both clang and gcc.
Clang generated executables would enter the if condition when it wasn't
supposted to, resulting in the wrong simulated behavior.
Implementing the operation this way is a bit faster anyway.
The changes made by the changeset 270c9a75e91f do not work well with switching
of cpus. The problem is that decoder for the old thread context holds state
that is not taken over by the new decoder.
This patch adds a takeOverFrom() function to Decoder class in each ISA. Except
for x86, functions in other ISAs are blank. For x86, the function copies state
from the old decoder to the new decoder.
Note that clflush is only being enabled. It is not implemented
in actual. A warning is printed if the cpu encounters a clflush
instruction. We need to enable this instruction in cpuid since
JRE 1.7 tests for it.
The changes made by the changeset 9376 were not quite correct. The patch made
changes to the code which resulted in decoder not getting initialized correctly
when the state was restored from a checkpoint.
This patch adds a startup function to each ISA object. For x86, this function
sets the required state in the decoder. For other ISAs, the function is empty
right now.
Used as a command in full-system scripts helps the user ensure the benchmarks have finished successfully.
For example, one can use:
/path/to/benchmark args || /sbin/m5 fail 1
and thus ensure gem5 will exit with an error if the benchmark fails.
This changeset inserts a TLB flush in BaseCPU::switchOut to prevent
stale translations when doing repeated switching. Additionally, the
TLB flushing functionality is exported to the Python to make debugging
of switching/checkpointing easier.
A simulation script will typically use the TLB flushing functionality
to generate a reference trace. The following sequence can be used to
simulate a handover (this depends on how drain is implemented, but is
generally the case) between identically configured CPU models:
m5.drain(test_sys)
[ cpu.flushTLBs() for cpu in test_sys.cpu ]
m5.resume(test_sys)
The generated trace should normally be identical to a trace generated
when switching between identically configured CPU models or
checkpointing and resuming.
Currently, we invalidate the cached miscregs in
TLB::unserialize(). The intended use of the drainResume() method is to
invalidate cached state and prepare the system to resume after a CPU
handover or (un)serialization. This patch moves the TLB miscregs
invalidation code to the drainResume() method to avoid surprising
behavior.
Since the page table walker only checks if a drain has completed in
doL1DescriptorWrapper() and doL2DescriptorWrapper(), it sometimes
looses track of a drain request if there is a squash. This changeset
adds a completeDrain() call after squashing requests in the pending
queue, which fixes this issue.
In order to see all registers independent of the current CPU mode, the
ARM architecture model uses the magic MISCREG_CPSR_MODE register to
change the register mappings without actually updating the CPU
mode. This hack is no longer needed since the thread context now
provides a flat interface to the register file. This patch replaces
the CPSR_MODE hack with the flat register interface.
After making the ISA an independent SimObject, it is serialized
automatically by the Python world. Previously, this just resulted in
an empty ISA section. This patch moves the contents of the ISA to that
section and removes the explicit ISA serialization from the thread
contexts, which makes it behave like a normal SimObject during
serialization.
Note: This patch breaks checkpoint backwards compatibility! Use the
cpt_upgrader.py utility to upgrade old checkpoints to the new format.
This patch adds support for the memInvalidate() drain method. TLB
flushing is requested by calling the virtual flushAll() method on the
TLB.
Note: This patch renames invalidateAll() to flushAll() on x86 and
SPARC to make the interface consistent across all supported
architectures.
At least gcc 4.4.3 seems to get confused by the use of func both as a
template parameter and a member variable in the M5VarArgsFault
class. This causes the value of the member variable func to be
unpredictable in M5VarArgsFault objects. This changeset renames the
template parameter to remove this ambiguity.
This patch makes the start and end address private in a move to
prevent direct manipulation and matching of ranges based on these
fields. This is done so that a transition to ranges with interleaving
support is possible.
As a result of hiding the start and end, a number of member functions
are needed to perform the comparisons and manipulations that
previously took place directly on the members. An accessor function is
provided for the start address, and a function is added to test if an
address is within a range. As a result of the latter the != and ==
operator is also removed in favour of the member function. A member
function that returns a string representation is also created to allow
debug printing.
In general, this patch does not add any functionality, but it does
take us closer to a situation where interleaving (and more cleverness)
can be added under the bonnet without exposing it to the user. More on
that in a later patch.
This patch makes the values of ID_ISARx, MIDR, and FPSID configurable
as ISA parameter values. Additionally, setMiscReg now ignores writes
to all of the ID registers.
Note: This moves the MIDR parameter from ArmSystem to ArmISA for
consistency.
The ISA class on stores the contents of ID registers on many
architectures. In order to make reset values of such registers
configurable, we make the class inherit from SimObject, which allows
us to use the normal generated parameter headers.
This patch introduces a Python helper method, BaseCPU.createThreads(),
which creates a set of ISAs for each of the threads in an SMT
system. Although it is currently only needed when creating
multi-threaded CPUs, it should always be called before instantiating
the system as this is an obvious place to configure ID registers
identifying a thread/CPU.
This patch unlocks the cpu-local monitor when the CPU sees a snoop to a locked
address. Previously we relied on the cache to handle the locking for us, however
some users on the gem5 mailing list reported a case where the cpu speculatively
executes a ll operation after a pending sc operation in the pipeline and that
makes the cache monitor valid. This should handle that case by invaliding the
local monitor.
This interface is no longer used, and getting rid of it simplifies the
decoders and code that sets up the decoders. The thread context had been used
to read architectural state which was used to contextualize the instruction
memory as it came in. That was changed so that the state is now sent to the
decoders to keep locally if/when it changes. That's significantly more
efficient.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
The predecoder in x86 does a lot of work, most of which can be skipped if the
decoder cache is put in front of it.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Avoid reading them every instruction, and also eliminate the last use of the
thread context in the decoders.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch implements the fnstsw instruction. The code was originally written
by Vince Weaver. Gabe had made some comments about the code, but those were
never addressed. This patch addresses those comments.
This patch implements the fsincos instruction. The code was originally written
by Vince Weaver. Gabe had made some comments about the code, but those were
never addressed. This patch addresses those comments.
uopSet_uop is microop instruction that has the IsControl flags set, but the
IsCondControl or IsUncondControl flags seems not to be set, neither in
the construction nor where the microop is used. This patch adds the the
flags in the constructor of the instruction (MicroUopSetPCCPSR).
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
A flag was missing for the movret_uop microop instruction. This patch adds
that flag when the instruction is used, not directly in the constructor of
the instruction.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch moves the draining interface from SimObject to a separate
class that can be used by any object needing draining. However,
objects not visible to the Python code (i.e., objects not deriving
from SimObject) still depend on their parents informing them when to
drain. This patch also gets rid of the CountedDrainEvent (which isn't
really an event) and replaces it with a DrainManager.
When casting objects in the generated SWIG interfaces, SWIG uses
classical C-style casts ( (Foo *)bar; ). In some cases, this can
degenerate into the equivalent of a reinterpret_cast (mainly if only a
forward declaration of the type is available). This usually works for
most compilers, but it is known to break if multiple inheritance is
used anywhere in the object hierarchy.
This patch introduces the cxx_header attribute to Python SimObject
definitions, which should be used to specify a header to include in
the SWIG interface. The header should include the declaration of the
wrapped object. We currently don't enforce header the use of the
header attribute, but a warning will be generated for objects that do
not use it.
This patch enables dumping statistics and Linux process information on
context switch boundaries (__switch_to() calls) that are used for
Streamline integration (a graphical statistics viewer from ARM).
This patch takes the Linux thread info support scattered across
different ISA implementations (currently in ARM, ALPHA, and MIPS), and
unifies them into a single file.
Adds a few more helper functions to read out TGID, mm, etc.
ISA-specific information (e.g., ALPHA PCBB register) is now moved to
the corresponding isa_traits.hh files.
This patch simplifies the scheduling of the next walk for the ARM
table walker. Previously it used the CPU clock, but as the table
walker inherits the clock from the CPU, it is cleaner to simply use
its own clock (which is the same).
This patch adds an additional level of ports in the inheritance
hierarchy, separating out the protocol-specific and protocl-agnostic
parts. All the functionality related to the binding of ports is now
confined to use BaseMaster/BaseSlavePorts, and all the
protocol-specific parts stay in the Master/SlavePort. In the future it
will be possible to add other protocol-specific implementations.
The functions used in the binding of ports, i.e. getMaster/SlavePort
now use the base classes, and the index parameter is updated to use
the PortID typedef with the symbolic InvalidPortID as the default.
This patch changes how the serialization of the system works. The base
class had a non-virtual serialize and unserialize, that was hidden by
a function with the same name for a number of subclasses (most likely
not intentional as the base class should have been virtual). A few of
the derived systems had no specialization at all (e.g. Power and x86
that simply called the System::serialize), but MIPS and Alpha adds
additional symbol table entries to the checkpoint.
Instead of overriding the virtual function, the additional entries are
now printed through a virtual function (un)serializeSymtab. The reason
for not calling System::serialize from the two related systems is that
a follow up patch will require the system to also serialize the
PhysicalMemory, and if this is done in the base class if ends up being
between the general parts and the specialized symbol table.
With this patch, the checkpoint is not modified, as the order of the
segments is unchanged.
This patch addresses a number of smaller issues identified by the code
inspection utility cppcheck. There are a number of identified leaks in
the arm/linux/system.cc (although the function only get's called once
so it is not a major problem), a few deletes in dev/x86/i8042.cc that
were not array deletes, and sprintfs where the character array had one
element less than needed. In the IIC tags there was a function
allocating an array of longs which is in fact never used.
Newer Linux kernels require DTB (device tree blobs) to specify platform
configurations. The input DTB filename can be specified through gem5 parameters
in LinuxArmSystem.
Instead of statically defining miscRegName to contain NUM_MISCREGS
elements, let the compiler determine the length of the array. This
allows us to use a static_assert to test that all registers are listed
in the name vector.
This patch takes the final plunge and transitions from the templated
Range class to the more specific AddrRange. In doing so it changes the
obvious Range<Addr> to AddrRange, and also bumps the range_map to be
AddrRangeMap.
In addition to the obvious changes, including the removal of redundant
includes, this patch also does some house keeping in preparing for the
introduction of address interleaving support in the ranges. The Range
class is also stripped of all the functionality that is never used.
--HG--
rename : src/base/range.hh => src/base/addr_range.hh
rename : src/base/range_map.hh => src/base/addr_range_map.hh
The patch introduces two predicates for condition code registers -- one
tests if a register needs to be read, the other tests whether a register
needs to be written to. These predicates are evaluated twice -- during
construction of the microop and during its execution. Register reads
and writes are elided depending on how the predicates evaluate.
The D flag bit is part of the cc flag bit register currently. But since it
is not being used any where in the implementation, it creates an unnecessary
dependency. Hence, it is being moved to a separate register.
This patch is meant for allowing predicated reads and writes. Note that this
predication is different from the ISA provided predication. They way we
currently provide the ISA description for X86, we read/write registers that
do not need to be actually read/written. This is likely to be true for other
ISAs as well. This patch allows for read and write predicates to be associated
with operands. It allows for the register indices for source and destination
registers to be decided at the time when the microop is constructed. The
run time indicies come in to play only when the at least one of the
predicates has been provided. This patch will not affect any of the ISAs that
do not provide these predicates. Also the patch assumes that the order in
which operands appear in any function of the microop is same across all the
functions of the microops. A subsequent patch will enable predication for the
x86 ISA.
This patch addresses the comments and feedback on the preceding patch
that reworks the clocks and now more clearly shows where cycles
(relative cycle counts) are used to express time.
Instead of bumping the existing patch I chose to make this a separate
patch, merely to try and focus the discussion around a smaller set of
changes. The two patches will be pushed together though.
This changes done as part of this patch are mostly following directly
from the introduction of the wrapper class, and change enough code to
make things compile and run again. There are definitely more places
where int/uint/Tick is still used to represent cycles, and it will
take some time to chase them all down. Similarly, a lot of parameters
should be changed from Param.Tick and Param.Unsigned to
Param.Cycles.
In addition, the use of curTick is questionable as there should not be
an absolute cycle. Potential solutions can be built on top of this
patch. There is a similar situation in the o3 CPU where
lastRunningCycle is currently counting in Cycles, and is still an
absolute time. More discussion to be had in other words.
An additional change that would be appropriate in the future is to
perform a similar wrapping of Tick and probably also introduce a
Ticks class along with suitable operators for all these classes.
This patch introduces the notion of a clock update function that aims
to avoid costly divisions when turning the current tick into a
cycle. Each clocked object advances a private (hidden) cycle member
and a tick member and uses these to implement functions for getting
the tick of the next cycle, or the tick of a cycle some time in the
future.
In the different modules using the clocks, changes are made to avoid
counting in ticks only to later translate to cycles. There are a few
oddities in how the O3 and inorder CPU count idle cycles, as seen by a
few locations where a cycle is subtracted in the calculation. This is
done such that the regression does not change any stats, but should be
revisited in a future patch.
Another, much needed, change that is not done as part of this patch is
to introduce a new typedef uint64_t Cycle to be able to at least hint
at the unit of the variables counting Ticks vs Cycles. This will be
done as a follow-up patch.
As an additional follow up, the thread context still uses ticks for
the book keeping of last activate and last suspend and this should
probably also be changed into cycles as well.
This patch removes the NACK frrom the packet as there is no longer any
module in the system that issues them (the bridge was the only one and
the previous patch removes that).
The handling of NACKs was mostly avoided throughout the code base, by
using e.g. panic or assert false, but in a few locations the NACKs
were actually dealt with (although NACKs never occured in any of the
regressions). Most notably, the DMA port will now never receive a NACK
and the backoff time is thus never changed. As a consequence, the
entire backoff mechanism (similar to a PCI bus) is now removed and the
DMA port entirely relies on the bus performing the arbitration and
issuing a retry when appropriate. This is more in line with e.g. PCIe.
Surprisingly, this patch has no impact on any of the regressions. As
mentioned in the patch that removes the NACK from the bridge, a
follow-up patch should change the request and response buffer size for
at least one regression to also verify that the system behaves as
expected when the bridge fills up.
