The DTRACE() macro tests both Trace::enabled and the specific flag. This
change uses the same administrative interface for enabling/disabling
tracing, but masks the SimpleFlags settings directly. This eliminates a
load for every DTRACE() test, e.g. DPRINTF.
In ARM, certain variables are only updated when a necessary change is
detected. Having 2 SMT threads share a TLB resulted in these not being
updated as required. This patch adds a thread context identifer to
assist in the invalidation of these variables.
Adds SMT support to the "simple" CPU models so that they can be
used with other SMT-supported CPUs. Example usage: this enables
the TimingSimpleCPU to be used to warmup caches before swapping to
detailed mode with the in-order or out-of-order based CPU models.
Trying to run an SE system with varying threads per core (SMT cores + Non-SMT
cores) caused failures due to the CPU id assignment logic. The comment
about thread assignment (worrying about core 0 not having tid 0) seems
not to be valid given that our configuration scripts initialize them in
order.
This removes that constraint so a heterogenously threaded sytem can work.
If a cache entry permission was previously set to NotPresent, but the entry was
not deleted, a following cache allocation can cause the entry to be leaked by
setting the entry pointer to a newly allocated entry. To eliminate this
possibility, check if the new entry is different from the old one, and if so,
delete the old one.
IntDevice::recvResponse is called from two places in current mainline: (1) the
short circuit path of X86ISA::IntDevice::IntMasterPort::sendMessage for atomic
mode, and (2) the full request->response path to and from the x86 interrupts
device (finally called from MessageMasterPort::recvTimingResp). In the former
case, the packet was deleted correctly, but in the latter case, the packet and
request leak. To fix the leak, move request and packet deletion into IntDevice
inherited class implementations of recvResponse.
In RubyPort::ruby_eviction_callback, prior changes fixed a memory leak caused
by instantiating separate packets for each port that the eviction was forwarded
to. That change, however, left the instantiated request to also leak. Allocate
it on the stack to avoid the leak.
Recent changes to memory access queuing allocate requests for packets sent to
memory controllers, but did not free the requests. Delete them to avoid leaks.
Changes to the RubyMemoryControl removed the dequeue function, which deleted
MemoryNode instances. This results in leaked MemoryNode instances. Correctly
delete these instances.
The recent changeset to readlink() to handle reading the /proc/self/exe link
introduces a number of problems. This patch fixes two:
1) Because readlink() called on /proc/self/exe now uses LiveProcess::progName()
to find the binary path, it will only get the zeroth parameter of the simulated
system command line. However, if a config script also specifies the process'
executable, the executable parameter is used to create the LiveProcess rather
than the zeroth command line parameter. Thus, the zeroth command line parameter
is not necessarily the correct path to the binary executing in the simulated
system. To fix this, add a LiveProcess data member, 'executable', which is
correctly set during instantiation and returned from progName().
2) If a config script allows a user to pass a relative path as the zeroth
simulated system command line parameter or process executable, readlink() will
incorrecly return a relative path when called on '/proc/self/exe'.
/proc/self/exe is always set to a full path, so running benchmarks can fail if
a relative path is returned. To fix this, clean up the handling of
LiveProcess::progName() within readlink() to get the full binary path.
NOTE: This patch still leaves the potential problem that host full path to the
binary bleeds into the simulated system, potentially causing the appearance of
non-deterministic simulated system execution.
This patch fixes a use-after-delete issue in the packet probe points
by adding a PacketInfo struct to retain the key fields before passing
the packet onwards. We want to probe the packet after it is
successfully sent, but by that time the fields may be modified, and
the packet may even be deleted.
Amazingly enough the issue has gone undetected for months, and only
recently popped up in our regressions.
This patch fixes issues in the interactions between deferred snoops
and WriteLineReq. More specifically, the patch addresses an issue
where deferred snoops caused assertion failures when being serviced on
the arrival of an InvalidateResp. The response packet was perceived to
be invalidating, when actually it is not for the cache that sent out
the original invalidation request.
This patch changes the tracking of ports in the snoop filter to use
local dense port IDs so that we can have 64 snooping ports (rather
than crossbar slave ports). This is achieved by adding a simple
remapping vector that translates the actal port IDs into the local
slave IDs used in the SnoopMask.
Ultimately this patch allows us to scale to much larger systems
without introducing a hierarchy of crossbars.
This patch adds a snoop filter to the L2XBar. For now we refrain from
globally adding a snoop filter to the SystemXBar, since the latter is
also used in systems without caches. In scenarios without caches the
snoop filter will not see any writeback/clean evicts from the CPU
ports, despite the fact that they are snooping. To avoid inadvertent
use of the snoop filter in these cases we leave it out for now.
A size check is added to the snoop filter, merely to ensure it does
not grow beyond the total capacity of the caches above it. The size
has to be set manually, and a value of 8 MByte is choosen as suitably
high default.
This patch introduces a private member storing the iterator from the
lookupRequest call, such that it can be re-used when the request
eventually finishes. The method previously called updateRequest is
renamed finishRequest to make it more clear that the two functions
must be called together.
This patch mirrors the logic in timing mode which sends up snoops to
check for cached copies before sending CleanEvicts and Writebacks down
the memory hierarchy. In case there is a copy in a cache above,
discard CleanEvicts and set the BLOCK_CACHED flag in Writebacks so
that writebacks do not reset the cache residency bit in the snoop
filter below.
This patch adds the functionality to properly track CleanEvicts and
Writebacks in the snoop filter. Previously there were no CleanEvicts, and
Writebacks did not send up snoops to ensure there were no copies in
caches above. Hence a writeback could never erase an entry from the
snoop filter.
When a CleanEvict message reaches a snoop filter, it confirms that the
BLOCK_CACHED flag is not set and resets the bits corresponding to the
CleanEvict address and port it arrived on. If none of the other peer
caches have (or have requested) the block, the snoop filter forwards
the CleanEvict to lower levels of memory. In case of a Writeback
message, the snoop filter checks if the BLOCK_CACHED flag is not set
and only then resets the bits corresponding to the Writeback
address. If any of the other peer caches have (or has requested) the
same block, the snoop filter sets the BLOCK_CACHED flag in the
Writeback before forwarding it to lower levels of memory heirarachy.
This patch prevents the snoop filter from creating items for requests
originating from non-snooping ports. The allocation decision is thus
based both on the cacheability of the line, and the snooping status of
the source port. Ultimately we should check if the source of the
packet is caching, since also the CPU ports are snooping (but not
allocating). Thus, at the moment we rely on the snoop filter being
used together with caches.
The patch also transitions to use the Packet::getBlockAddr in
determining the line address.
This patch introduces the concept of a snoop latency. Given the
requirement to snoop and forward packets in zero time (due to the
coherency mechanism), the latency is accounted for later.
On a snoop, we establish the latency, and later add it to the header
delay of the packet. To allow multiple caches to contribute to the
snoop latency, we use a separate variable in the packet, and then take
the maximum before adding it to the header delay.
This patch ensures that the snoop-filter latency only contributes to
the packet latency, and not to the crossbar throughput/occupancy. In
essence we treat the snoop-filter lookup as pipelined.
Created the following HBM configurations:
1) HBM gen1 (x128/CH), 2Gb die, 4H stack, 1Gbps, 8 channels
2) HBM gen2 (x64/PC), 8Gb die, 4H stack, 1Gbps, 16 pseudo-channels
The configuration values are based on:
- The HBM gen1 public JEDEC spec
- Publically released data from MemCon presentations
- Timing extrapolated from existing LPDDR configurations
Will adjust once specs become available.
Changeset 4872dbdea907 replaced Address by Addr, but did not make changes to
print statements. So the addresses which were being printed in hex earlier
along with their line address, were now being printed in decimals. This patch
adds a function printAddress(Addr) that can be used to print the address in hex
along with the lines address. This function has been put to use in some of the
places. At other places, change has been made to print just the address in
hex.
The DataMember class in Type.py was being derived from PairContainer. A
separate Var object was also created for the DataMember. This meant some
duplication of across the members of these two classes (Var and DataMember).
This patch changes DataMember from Var instead. There is no obvious reason to
derive from PairContainer which can only hold pairs, something that Var class
already supports. The only thing that DataMember has over Var is init_code,
which is being retained. This change would later on help in having pointers
in DataMembers.
Some blocks in MOESI hammer were not getting deallocated when they were set to
an idle state (e.g. by invalidate or other_getx/s messages). While
functionally correct, this caused some bad effects on performance, such as
blocks in I in the L1s getting sent to the L2 upon eviction, in turn evicting
valid blocks. Also, if a valid block was in LRU, that block could be evicted
rather than a block in I. This patch adds in the missing deallocations.
Committed by: Nilay Vaish<nilay@cs.wisc.edu>
The recent changes to make MessageBuffers SimObjects required them to be
initialized in a particular order, which could break some protocols. Fix this
by calling initNetQueues on the external nodes of each external link in the
constructor of Network.
This patch also refactors the duplicated code for checking network allocation
and setting net queues (which are called by initNetQueues) from the simple and
garnet networks to be in Network.
This patch changes MessageBuffer and TimerTable, two structures used for
buffering messages by components in ruby. These structures would no longer
maintain pointers to clock objects. Functions in these structures have been
changed to take as input current time in Tick. Similarly, these structures
will not operate on Cycle valued latencies for different operations. The
corresponding functions would need to be provided with these latencies by
components invoking the relevant functions. These latencies should also be
in Ticks.
I felt the need for these changes while trying to speed up ruby. The ultimate
aim is to eliminate Consumer class and replace it with an EventManager object in
the MessageBuffer and TimerTable classes. This object would be used for
scheduling events. The event itself would contain information on the object and
function to be invoked.
In hindsight, it seems I should have done this while I was moving away from use
of a single global clock in the memory system. That change led to introduction
of clock objects that replaced the global clock object. It never crossed my
mind that having clock object pointers is not a good design. And now I really
don't like the fact that we have separate consumer, receiver and sender
pointers in message buffers.
The eventual aim of this change is to pass RubySystem pointers through to
objects generated from the SLICC protocol code.
Because some of these objects need to dereference their RubySystem pointers,
they need access to the System.hh header file.
In src/mem/ruby/SConscript, the MakeInclude function creates single-line header
files in the build directory that do nothing except include the corresponding
header file from the source tree.
However, SLICC also generates a list of header files from its symbol table, and
writes it to mem/protocol/Types.hh in the build directory. This code assumes
that the header file name is the same as the class name.
The end result of this is the many of the generated slicc files try to include
RubySystem.hh, when the file they really need is System.hh. The path of least
resistence is just to rename System.hh to RubySystem.hh.
--HG--
rename : src/mem/ruby/system/System.cc => src/mem/ruby/system/RubySystem.cc
rename : src/mem/ruby/system/System.hh => src/mem/ruby/system/RubySystem.hh
This register is writable according to UA2005
Tried to boot NetBSD which starts the kernel by writing to the tick_cmpr
register. Without the patch gem5 crashes with a panic. With the patch NetBSD
starts to boot normally (although sun4v support in NetBSD is not complete yet)
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Handle bad IDE disk image size 0. When image size is 0, gem5 will cause an
exception with log "Floating point exception (core dumped)".
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
When a branch gets squashed, it's speculative branch predictor state should get
rolled back in squash(). However, only the globalHistory state was being
rolled back. This patch adds (at least some) support for rolling back the
local predictor state also.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch enables instructions in LSQ to track two physical addresses for
corresponding two split requests. Later, the information is used in
checksnoop() to search for/invalidate the corresponding LD instructions.
The current implementation has kept track of only the physical address that is
referenced by the first split request. Thus, for checksnoop(), the line
accessed by the second request has not been considered, causing potential
correctness issues.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Refactored the code in operateVnet(), moved partly to a new function
operateMessageBuffer(). This is required since a later patch moves to having a
wakeup event per MessageBuffer instead of one event for the entire Switch.
There are two reasons for doing so:
a. provide a source of clock to PerfectSwitch. A follow on patch removes sender
and receiver pointers from MessageBuffer means that the object owning the
buffer should have some way of providing timing info.
b. schedule events. A follow on patch removes the consumer class. So the
PerfectSwitch needs some EventManager object to schedule events on its own.
Add a stat that counts buffer underruns in the HDLCD controller. The
stat counts at most one underrun per frame since the controller aborts
the current frame if it underruns.
Rewrite the HDLCD controller to use the new DMA engine and pixel
pump. This fixes several bugs in the current implementation:
* Broken/missing interrupt support (VSync, underrun, DMA end)
* Fragile resolution changes (changing resolutions used
to cause assertion errors).
* Support for resolutions with a width that isn't divisible by 32.
* The pixel clock can now be set dynamically.
This breaks checkpoint compatibility. Checkpoints can be upgraded with
the checkpoint conversion script. However, upgraded checkpoints won't
contain the state of the current frame. That means that HDLCD
controllers restoring from a converted checkpoint immediately start
drawing a new frame (i.e, expect timing differences).
Currently the sequencer calls the function setMRU that updates the replacement
policy structures with the first level caches. While functionally this is
correct, the problem is that this requires calling findTagInSet() which is an
expensive function. This patch removes the calls to setMRU from the sequencer.
All controllers should now update the replacement policy on their own.
The set and the way index for a given cache entry can be found within the
AbstractCacheEntry structure. Use these indicies to update the replacement
policy structures.
The current Set data structure is slow and therefore is being reimplemented
using std::bitset. A maximum limit of 64 is being set on the number of
controllers of each type. This means that for simulating a system with more
controllers of a given type, one would need to change the value of the variable
NUMBER_BITS_PER_SET
MessageBuffer is a SimObject now. There were protocols that still declared
some of the message buffers are variables of the controller, but not as input
parameters. Special handling was required for these variables in the SLICC
compiler. This patch changes this. Now all message buffers are declared as
input parameters.
In cases where a newly added target does not have any upstream MSHR to
mark as downstreamPending, remember that nothing is marked. This
allows us to avoid attempting to find the MSHR as part of the clearing
of downstreamPending.
This commit addresses gem5 checkpoints' linear versioning bottleneck.
Since development is distributed across many private trees, there exists
a sort of 'race' for checkpoint version numbers: internally a checkpoint
version may be used but then resynchronizing with the external tree causes
a conflict on that version. This change replaces the linear version number
with a set of unique strings called tags. Now the only conflicts that can
arise are of tag names, where collisions are much easier to avoid.
The checkpoint upgrader (util/cpt_upgrader.py) upgrades the version
representation, as one would expect. Each tag version implements its
upgrader code in a python file in the util/cpt_upgraders directory
rather than adding a function to the upgrader script itself.
The version tags are stored in the 'Globals' section rather than 'root'
(as the version was previously) because 'Globals' gets unserialized
first and can provide a warning before any other unserialization errors
can occur.
This is in support of tag-based checkpoint versioning. It should be
possible to examine an optional parameter in a checkpoint during
unserialization and not have it throw a warning.
We no longer use the C library based random number generator: random().
Instead we use the C++ library provided rng. So setting the random seed for
the RubySystem class has no effect. Hence the variable and the corresponding
option are being dropped.
Event auto-serialization no longer in use and has been broken ever
since the introduction of PDES support almost two years
ago. Additionally, serializing the individual event queues is
undesirable since it exposes the thread structure of the
simulator. What this means in practice is that the number of threads
in the simulator must be the same when taking a checkpoint and when
loading the checkpoint.
This changeset removes support for the AutoSerialize event flag and
the associated serialization code.
EtherLink currently uses a fire-and-forget link delay event that
delays sending of packets by a fixed number of ticks. In order to
serialize this event, it relies on the event queue's auto
serialization support. However, support for event auto serialization
has been broken for more than two years, which means that checkpoints
of multi-system setups are likely to drop in-flight packets.
This changeset the replaces rewrites this part of the EtherLink to use
a packet queue instead. The queue contains a (tick, packet) tuple. The
tick indicates when the packet will be ready. Instead of relying on
event autoserialization, we now explicitly serialize the packet queue
in the EhterLink::Link class.
Note that this changeset changes the way in-flight packages are
serialized. Old checkpoints will still load, but in-flight packets
will be dropped (just as before). There has been no attempt to upgrade
checkpoints since this would actually change the behavior of existing
checkpoints.
This changeset removes the support for the autoserialize parameter in
GlobalSimLoopExitEvent (including exitSimLoop()) and
LocalSimLoopExitEvent.
Auto-serialization of the LocalSimLoopExitEvent was never used, so
this is not expected to affect anything. However, it was sometimes
used for GlobalSimLoopExitEvent. Unfortunately, serialization of
global events has never been supported, so checkpoints with such
events will currently cause simulation panics.
The serialize parameter to exitSimLoop() has been left in-place to
maintain API compatibility (removing it would affect m5ops). Instead
of just dropping it, we now print a warning if the parameter is set
and the exit event is scheduled in the future (i.e., not at the
current tick).
The object resolver isn't serialization specific and shouldn't live in
serialize.hh. Move it to sim_object.hh since it queries to the
SimObject hierarchy.
This member indicates whether or not a particular virtual network is in use.
Instead of having a default big value for the number of virtual networks and
then checking whether a virtual network is in use, the next patch removes the
default value and the protocol configuration file would now specify the
number of virtual networks it requires.
Additionally, the patch also refactors some of the code used for computing the
virtual channel next in the round robin order.
Both FuncCallExprAST and MethodCallExprAST had code for checking the arguments
with which a function is being called. The patch does away with this
duplication. Now the code for checking function call arguments resides in the
Func class.
The new serialization code (kudos to Tim Jones) moves all of the state
mangling in RubySystem to memWriteback. This makes it possible to use
the new const serialization interface.
This changeset moves the cache recorder cleanup from the checkpoint()
method to drainResume() to make checkpointing truly constant and
updates the checkpointing code to use the new interface.
The sequencer takes care of llsc accesses by calling upon functions
from the CacheMemory. This is unnecessary once the required CacheEntry object
is available. Thus some of the calls to findTagInSet() are avoided.
The O3CPU blocks the Fetch when it sees a quiesce instruction (IsQuiesce flag).
When the inst. is executed, a quiesce event is created to reactivate the
context and unblock the Fetch.
If the quiesceNs or quiesceCycles are called with a value of 0, the
QuiesceEvent will not be created and the Fetch stage will remain blocked.
Committed by Joel Hestness <jthestness@gmail.com>
This patch reverts part of (842f56345a42), as apparently there are
use-cases outside the main repository relying on the late setting of
the physical address.
This patch simplifies the packet, and removes the possibility of
creating a packet without a valid address and/or size. Under no
circumstances are these fields set at a later point, and thus they
really have to be provided at construction time.
The patch also fixes a case there the MinorCPU creates a packet
without a valid address and size, only to later delete it.
Cleaning up dead code. The CLREX stores zero directly to
MISCREG_LOCKFLAG and so the request flag is no longer needed. The
corresponding functionality in the cache tags is also removed.
Open up for other subclasses to BaseCache and transition to using the
explicit Cache subclass.
--HG--
rename : src/mem/cache/BaseCache.py => src/mem/cache/Cache.py
This patch serves to avoid name clashes with the classic cache. For
some reason having two 'SimObject' files with the same name creates
problems.
--HG--
rename : src/mem/ruby/structures/Cache.py => src/mem/ruby/structures/RubyCache.py
We no longer use the C library based random number generator: random().
Instead we use the C++ library provided rng. So setting the random seed for
the RubySystem class has no effect. Hence the variable and the corresponding
option are being dropped.
Currently the sequencer calls the function setMRU that updates the replacement
policy structures with the first level caches. While functionally this is
correct, the problem is that this requires calling findTagInSet() which is an
expensive function. This patch removes the calls to setMRU from the sequencer.
All controllers should now update the replacement policy on their own.
The set and the way index for a given cache entry can be found within the
AbstractCacheEntry structure. Use these indicies to update the replacement
policy structures.
Before this patch, while one could declare / define a function with default
argument values, but the actual function call would require one to specify
all the arguments. This patch changes the check for function arguments.
Now a function call needs to specify arguments that are at least as much as
those with default values and at most the total number of arguments taken
as input by the function.
Both FuncCallExprAST and MethodCallExprAST had code for checking the arguments
with which a function is being called. The patch does away with this
duplication. Now the code for checking function call arguments resides in the
Func class.
This is in preparation for adding a second arugment to the lookup
function for the CacheMemory class. The change to *.sm files was made using
the following sed command:
sed -i 's/\[\([0-9A-Za-z._()]*\)\]/.lookup(\1)/' src/mem/protocol/*.sm
The sequencer takes care of llsc accesses by calling upon functions
from the CacheMemory. This is unnecessary once the required CacheEntry object
is available. Thus some of the calls to findTagInSet() are avoided.
This patch eliminates the type Address defined by the ruby memory system.
This memory system would now use the type Addr that is in use by the
rest of the system.
Expose MessageBuffers from SLICC controllers as SimObjects that can be
manipulated in Python. This patch has numerous benefits:
1) First and foremost, it exposes MessageBuffers as SimObjects that can be
manipulated in Python code. This allows parameters to be set and checked in
Python code to avoid obfuscating parameters within protocol files. Further, now
as SimObjects, MessageBuffer parameters are printed to config output files as a
way to track parameters across simulations (e.g. buffer sizes)
2) Cleans up special-case code for responseFromMemory buffers, and aligns their
instantiation and use with mandatoryQueue buffers. These two special buffers
are the only MessageBuffers that are exposed to components outside of SLICC
controllers, and they're both slave ends of these buffers. They should be
exposed outside of SLICC in the same way, and this patch does it.
3) Distinguishes buffer-specific parameters from buffer-to-network parameters.
Specifically, buffer size, randomization, ordering, recycle latency, and ports
are all specific to a MessageBuffer, while the virtual network ID and type are
intrinsics of how the buffer is connected to network ports. The former are
specified in the Python object, while the latter are specified in the
controller *.sm files. Unlike buffer-specific parameters, which may need to
change depending on the simulated system structure, buffer-to-network
parameters can be specified statically for most or all different simulated
systems.
CacheMemory and DirectoryMemory lookup functions return pointers to entries
stored in the memory. Bring PerfectCacheMemory in line with this convention,
and clean up SLICC code generation that was in place solely to handle
references like that which was returned by PerfectCacheMemory::lookup.
The RubyCache (CacheMemory) latency parameter is only used for top-level caches
instantiated for Ruby coherence protocols. However, the top-level cache hit
latency is assessed by the Sequencer as accesses flow through to the cache
hierarchy. Further, protocol state machines should be enforcing these cache hit
latencies, but RubyCaches do not expose their latency to any existng state
machines through the SLICC/C++ interface. Thus, the RubyCache latency parameter
is superfluous for all caches. This is confusing for users.
As a step toward pushing L0/L1 cache hit latency into the top-level cache
controllers, move their latencies out of the RubyCache declarations and over to
their Sequencers. Eventually, these Sequencer parameters should be exposed as
parameters to the top-level cache controllers, which should assess the latency.
NOTE: Assessing these latencies in the cache controllers will require modifying
each to eliminate instantaneous Ruby hit callbacks in transitions that finish
accesses, which is likely a large undertaking.
The Packet::get() and Packet::set() methods both have very strange
semantics. Currently, they automatically convert between the guest
system's endianness and the host system's endianness. This behavior is
usually undesired and unexpected.
This patch introduces three new method pairs to access data:
* getLE() / setLE() - Get data stored as little endian.
* getBE() / setBE() - Get data stored as big endian.
* get(ByteOrder) / set(v, ByteOrder) - Configurable endianness
For example, a little endian device that is receiving a write request
will use teh getLE() method to get the data from the packet.
The old interface will be deprecated once all existing devices have
been ported to the new interface.
Timing generator for a pixel-based display. The timing generator is
intended for display processors driving a standard rasterized
display. The simplest possible display processor needs to derive from
this class and override the nextPixel() method to feed the display
with pixel data.
Pixels are ordered relative to the top left corner of the
display. Scan lines appear in the following order:
* Vertical Sync (starting at line 0)
* Vertical back porch
* Visible lines
* Vertical front porch
Pixel order within a scan line:
* Horizontal Sync
* Horizontal Back Porch
* Visible pixels
* Horizontal Front Porch
All events in the timing generator are automatically suspended on a
drain() request and restarted on drainResume(). This is conceptually
equivalent to clock gating when the pixel clock while the system is
draining. By gating the pixel clock, we prevent display controllers
from disturbing a memory system that is about to drain.
Add support for oscillators that can be programmed using the RealView
/ Versatile Express configuration interface. These oscillators are
typically used for things like the pixel clock in the display
controller.
The default configurations support the oscillators from a Versatile
Express motherboard (V2M-P1) with a CoreTile Express A15x2.
Add a simple DMA engine that sits behind a FIFO. This engine can be
used by devices that need to read large amounts of data (e.g., display
controllers). Most aspects of the controller, such as FIFO size,
maximum number of in-flight accesses, and maximum request sizes can be
configured.
The DMA copies blocks of data into its FIFO. Transfers are initiated
with a call to startFill() command that takes a start address and a
size. Advanced users can create a derived class that overrides the
onEndOfBlock() callback that is triggered when the last request to a
block has been issued. At this point, the DMA engine is ready to start
fetching a new block of data, potentially from a different address
range.
The DMA engine stops issuing new requests while it is draining. Care
must be taken to ensure that devices that are fed by a DMA engine are
suspended while the system is draining to avoid buffer underruns.
Split ClockedObject into two classes: Clocked that provides the basic
clock functionality, and ClockedObject that inherits from Clocked and
SimObject to provide the functionality of the old ClockedObject.
The CircleBuf class has at least one bug causing it to overwrite the
wrong elements when wrapping. The current code has a lot of unused
functionality and duplicated code. This changeset replaces the old
implementation with a new version that supports serialization and
arbitrary types in the buffer (not just char).
The i8042 device drops the contents of a PS2 device's buffer when
serializing, which results in corrupted PS2 state when continuing
simulation after a checkpoint. This changeset fixes this bug and
transitions the i8042 model to use the new serialization API that
requires the serialize() method to be const.
Declare the constructor and all of the operators that don't change the
state of a Cycles instance as constexpr. This makes it possible to use
Cycles as a static constant and allows the compiler to evaulate simple
expressions at compile time. An unfortunate side-effect of this is
that we cannot use assertions since C++11 doesn't support them in
constexpr functions. As a workaround, we throw an invalid_argument
exception when the assert would have triggered. A nice side-effect of
this is that the compiler will evaluate the "assertion" at compile
time when an expression involving Cycles can be statically evaluated.
This patch removes the extraneous flags and attributes from the
request and packet, and simply leaves the new commands. The change
introduced when adding acquire/release breaks all compatibility with
existing traces, and there is really no need for any new flags and
attributes. The commands should be sufficient.
This patch fixes packet tracing (urgent), and also removes the
unnecessary complexity.
It is sometimes desirable to be able to instantiate Drainable objects
when the simulator isn't in the Running state. Currently, we always
initialize Drainable objects to the Running state. However, this
confuses many of the sanity checks in the base class since objects
aren't expected to be in the Running state if the system is in the
Draining or Drained state.
Instead of always initializing the state variable in Drainable to
DrainState::Running, initialize it to the state the DrainManager is
in.
Note: This means an object can be created in the Draining/Drained
state without first calling drain().
This changeset moves the access trace functionality from the
CommMonitor into a separate probe. The probe can be hooked up to any
component that exports probe points of the type ProbePoints::Packet.
This patch moves the dependency on Google's Protocol Buffers library
from the CommMonitor to the MemTraceProbe, which means that the
CommMonitor (including stack distance profiling) no long depends on
it.
This changeset removes the stack distance calculator hooks from the
CommMonitor class and implements a stack distance calculator as a
memory system probe instead. The probe can be hooked up to any
component that exports probe points of the type ProbePoints::Packet.
This changeset adds a standardized probe point type to monitor packets
in the memory system and adds two probe points to the CommMonitor
class. These probe points enable monitoring of successfully delivered
requests and successfully delivered responses.
Memory system probe listeners should use the BaseMemProbe base class
to provide a unified configuration interface and reuse listener
registration code. Unlike the ProbeListenerObject class, the
BaseMemProbe allows objects to be wired to multiple ProbeManager
instances as long as they use the same probe point name.
There are 2 problems with the existing checkpoint and restore code in ruby.
The first is that when the event queue is altered by ruby during serialization,
some events that are currently scheduled cannot be found (e.g. the event to
stop simulation that always lives on the queue), causing a panic.
The second is that ruby is sometimes serialized after the memory system,
meaning that the dirty data in its cache is flushed back to memory too late
and so isn't included in the checkpoint.
These are fixed by implementing memory writeback in ruby, using the same
technique of hijacking the event queue, but first descheduling all events that
are currently on it. They are saved, along with their scheduled time, so that
the event queue can be faithfully reconstructed after writeback has finished.
Events with the AutoDelete flag set will delete themselves when they
are descheduled, causing an error when attempting to schedule them again.
This is fixed by simply not recording them when taking them off the queue.
Writeback is still implemented using flushing, so the cache recorder object,
that is created to generate the trace and manage flushing, is kept
around and used during serialization to write the trace to disk.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
1. Eliminate state NP in L0 and L1 Caches: The two states 'NP' and 'I' both
mean that the cache block is not present in the cache. 'I' also means that the
cache entry has been allocated. This causes problems when we do not correctly
initialize the cache entry when it is re-used. Hence, this patch eliminates
the state NP altogether. Everytime a new block comes into the cache, a cache
entry is allocated. Everytime a block leaves, the corresponding entry is
deallocated.
2. Separate transient state for instruction fetches: purely for accouting
purposes.
3. Drop state IS_I in L1 Cache and the message type STALE_DATA: when
invalidation is received for a block in IS, the block used to be moved to IS_I.
This meant that the data that would arrive in future would be used but not
stored since the controller lost the permissions after gaining them. This
state is being dropped and now invalidation messages would not processed till
the data has arrived. This also means that STALE_DATA type is not longer
required.
The level 2 controller has a bug. In one particular action, the data block was
copied from a message irrespective whether the block is dirty or not. In cases
when L1 sends no data, the data value copied was incorrect.
For many years the slicc symbol table has supported overloaded functions in
external classes. This patch extends that support to functions that are not
part of classes (a.k.a. no parent). For example, this support allows slicc
to understand that mapAddressToRange is overloaded and the NodeID is an
optional parameter.
This patch changes the router pipeline stages from 4 to 2. The
canonical 4-stage router is conservative while a lower-latency router
with look ahead routing and speculative allocation is well acknowledged.
Sets m_stage.second to the second parameter of the function.
Then, for every place where advance_stage is called, adds
a cycle to the argument being passed.
Adds features to allow protocols to reschedule controllers when conditionally
stalling within inport logic or actions. Also insures that resource and
protocol stalls are re-evaluated the next cycle.
This patch adds support that allows the replacement policy to identify each
cache block's access permission. This information can be useful when making
replacement decisions.
The Ruby banked array resource checks (initiated from SLICC) did a check and
allocate at the same time. If a transition needs more than one resource, then
it might check/allocate resource #1, then fail to get resource #2. Another
transition might then try to get the same resources, but in reverse order.
Deadlock.
This patch separates resource checking and resource reservation into two
steps to avoid deadlock.
It was previously possible for a stalled message to be reordered after an
incomming message. This patch ensures that any stalled message stays in its
original request order.
This patch adds a few helpful functions that allow .sm files to directly
invalidate all cache blocks using a trigger queue rather than rely on each
individual cache block to be invalidated via requests from the mandatory
queue.
This patch allows DPRINTFs to be used in SLICC state machines similar to how
they are used by the rest of gem5. Previously all DPRINTFs in the .sm files
had to use the RubySlicc flag.
This patch exposes the tag and data array latencies to the SLICC state machines
so that it can be used to determine the correct enqueue latency for response
messages.
To have multiple Entry types (e.g., a cache Entry type and
a directory Entry type), just declare one of them as a secondary
type by using the pair 'main="false"', e.g.:
structure(DirEntry, desc="...", interface="AbstractCacheEntry",
main="false") {
...and the primary type would be declared:
structure(Entry, desc="...", interface="AbstractCacheEntry") {
This patch fixes the type handling when prefix operations are used. Previously
prefix operators would assume a void return type, which made it impossible to
combine prefix operations with other expressions. This patch allows SLICC
programmers to use prefix operations more naturally.
This patches adds support for transitions of the form:
transition(START, EVENTS, *) { ACTIONS }
This allows a machine to collapse states that differ only in the next state
transition to collapse into one, and can help shorten/simplfy some protocols
significantly.
When * is encountered as an end state of a transition, the next state is
determined by calling the machine-specific getNextState function. The next
state is determined before any actions of the transition execute, and
therefore the next state calculation cannot depend on any of the transition
actions.
This patch allows SLICC protocols to use more than one message type with a
message buffer. For example, you can declare two in ports as such:
in_port(ResponseQueue_in, ResponseMsg, responseFromDir, rank=3) { ... }
in_port(tgtResponseQueue_in, TgtResponseMsg, responseFromDir, rank=2) { ... }
This patch was created by Bihn Pham during his internship at AMD.
There is no need to delay hit callback response messages by a cycle because
the response latency is already incurred in the Ruby protocol. This ensures
correct timing of memory instructions.
The Minor CPU currently doesn't drain properly when it is switched
out. This happens because Fetch 1 expects to be in the FetchHalted
state when it is drained. However, because the CPU is switched out, it
is stuck in the FetchWaitingForPC state. Fix this by ignoring drain
requests and returning DrainState::Drained from MinorCPU::drain() if
the CPU is switched out. This is always safe since a switched out CPU,
by definition, doesn't have any instructions in flight.
Minor currently activates thread 0 in startup() to work around an
issue where activateContext() is called from LiveProcess before the
process entry point is known. When activateContext() is called, Minor
creates a branch instruction to the process's entry point. The first
time it is called, the branch points to an undefined location (0). The
call in startup() updates the branch to point to the actual entry
point.
When instantiating a switched out Minor CPU, it still tries to
activate thread 0. This is clearly incorrect since a switched out CPU
can't have any active threads. This changeset adds a check to ensure
that the thread is active before reactivating it.
The drain refactor patches introduced a couple of bugs in the way
Minor handles draining. This patch fixes an incorrect assert and a
case of infinite recursion when the CPU signals drain done.
This patch removes the RequestCause, and also simplifies how we
schedule the sending of packets through the memory-side port. The
deassertion of bus requests is removed as it is not used.
This patch makes cache sets aware of the way number. This enables
some nice features such as the ablity to restrict way allocation. The
implemented mechanism allows to set a maximum way number to be
allocated 'k' which must fulfill 0 < k <= N (where N is the number of
ways). In the future more sophisticated mechasims can be implemented.
This patch changes how writebacks communicate whether the line is
passed as modified or owned. Previously we relied on the
isSupplyExclusive mechanism, which was originally designed to avoid
unecessary snoops.
For normal cache requests we use the sharedAsserted mechanism to
determine if a block should be marked writeable or not, and with this
patch we transition the writebacks to also use this
mechanism. Conceptually this is cleaner and more consistent.
Some minor fixes and removal of dead code. Changing the flags to be
enums rather than static const (to avoid any linking issues caused by
the latter). Also adding a getBlockAddr member which hopefully can
slowly finds its way into caches, snoop filters etc.
This adds a vector register type. The type is defined as a std::array of a
fixed number of uint64_ts. The isa_parser.py has been modified to parse vector
register operands and generate the required code. Different cpus have vector
register files now.
The Process class methods were using an improper style and this subsequently
bled into the system call code. The following regular expressions should be
helpful if someone transitions private system call patches on top of these
changesets:
s/alloc_fd/allocFD/
s/sim_fd(/simFD(/
s/sim_fd_obj/getFDEntry/
s/fix_file_offsets/fixFileOffsets/
s/find_file_offsets/findFileOffsets/
The patch clarifies whether file descriptors are host file descriptors or
target file descriptors in the system call code. (Host file descriptors
are file descriptors which have been allocated through real system calls
where target file descriptors are allocated from an array in the Process
class.)
This patch extends the previous patch's alterations around fd_map. It cleans
up some of the uglier code in the process file and replaces it with a more
concise C++11 version. As part of the changes, the FdMap class is pulled out
of the Process class and receives its own file.
This patch gets rid of unused Process::dup_fd method and does minor
refactoring in the process class files. The file descriptor max has been
changed to be the number of file descriptors since this clarifies the loop
boundary condition and cleans up the code a bit. The fd_map field has been
altered to be dynamically allocated as opposed to being an array; the
intention here is to build on this is subsequent patches to allow processes
to share their file descriptors with the clone system call.
This patch updates the x86 decoder so that it can decode instructions with vex
prefix. It also updates the isa with opcodes from vex opcode maps 1, 2 and 3.
Note that none of the instructions have been implemented yet. The
implementations would be provided in due course of time.
Multi gem5 is an extension to gem5 to enable parallel simulation of a
distributed system (e.g. simulation of a pool of machines
connected by Ethernet links). A multi gem5 run consists of seperate gem5
processes running in parallel (potentially on different hosts/slots on
a cluster). Each gem5 process executes the simulation of a component of the
simulated distributed system (e.g. a multi-core board with an Ethernet NIC).
The patch implements the "distributed" Ethernet link device
(dev/src/multi_etherlink.[hh.cc]). This device will send/receive
(simulated) Ethernet packets to/from peer gem5 processes. The interface
to talk to the peer gem5 processes is defined in dev/src/multi_iface.hh and
in tcp_iface.hh.
There is also a central message server process (util/multi/tcp_server.[hh,cc])
which acts like an Ethernet switch and transfers messages among the gem5 peers.
A multi gem5 simulations can be kicked off by the util/multi/gem5-multi.sh
wrapper script.
Checkpoints are supported by multi-gem5. The checkpoint must be
initiated by a single gem5 process. E.g., the gem5 process with rank 0
can take a checkpoint from the bootscript just before it invokes
'mpirun' to launch an MPI test. The message server process will notify
all the other peer gem5 processes and make them take a checkpoint, too
(after completing a global synchronisation to ensure that there are no
inflight messages among gem5).
This is another step in the process of removing global variables
from Ruby to enable multiple RubySystem instances in a single simulation.
The list of abstract controllers is per-RubySystem and should be
represented that way, rather than as a global.
Since this is the last remaining Ruby global variable, the
src/mem/ruby/Common/Global.* files are also removed.
This is another step in the process of removing global variables
from Ruby to enable multiple RubySystem instances in a single simulation.
With possibly multiple RubySystem objects, we can no longer use a global
variable to find "the" RubySystem object. Instead, each Ruby component
has to carry a pointer to the RubySystem object to which it belongs.
This patch begins the process of removing global variables from the Ruby
source with the goal of eventually allowing users to create multiple Ruby
instances in a single simulation. Currently, users cannot do so because
several global variables and static members are referenced by the RubySystem
object in a way that assumes that there will only ever be a single RubySystem.
These need to be replaced with per-RubySystem equivalents.
This specific patch replaces the global var g_ruby_start, which is used
to calculate throughput statistics for Throttles in simple networks and
links in Garnet networks, with a RubySystem instance var m_start_cycle.
Add a simple device shim that interfaces with the NoMali model
library. The gem5 side of the interface supports Mali T60x/T62x/T760
GPUs. This device model pretends to be a Mali GPU, but doesn't render
anything and executes in zero time.
The drain() call currently passes around a DrainManager pointer, which
is now completely pointless since there is only ever one global
DrainManager in the system. It also contains vestiges from the time
when SimObjects had to keep track of their child objects that needed
draining.
This changeset moves all of the DrainState handling to the Drainable
base class and changes the drain() and drainResume() calls to reflect
this. Particularly, the drain() call has been updated to take no
parameters (the DrainManager argument isn't needed) and return a
DrainState instead of an unsigned integer (there is no point returning
anything other than 0 or 1 any more). Drainable objects should return
either DrainState::Draining (equivalent to returning 1 in the old
system) if they need more time to drain or DrainState::Drained
(equivalent to returning 0 in the old system) if they are already in a
consistent state. Returning DrainState::Running is considered an
error.
Drain done signalling is now done through the signalDrainDone() method
in the Drainable class instead of using the DrainManager directly. The
new call checks if the state of the object is DrainState::Draining
before notifying the drain manager. This means that it is safe to call
signalDrainDone() without first checking if the simulator has
requested draining. The intention here is to reduce the code needed to
implement draining in simple objects.
Draining is currently done by traversing the SimObject graph and
calling drain()/drainResume() on the SimObjects. This is not ideal
when non-SimObjects (e.g., ports) need draining since this means that
SimObjects owning those objects need to be aware of this.
This changeset moves the responsibility for finding objects that need
draining from SimObjects and the Python-side of the simulator to the
DrainManager. The DrainManager now maintains a set of all objects that
need draining. To reduce the overhead in classes owning non-SimObjects
that need draining, objects inheriting from Drainable now
automatically register with the DrainManager. If such an object is
destroyed, it is automatically unregistered. This means that drain()
and drainResume() should never be called directly on a Drainable
object.
While implementing the new functionality, the DrainManager has now
been made thread safe. In practice, this means that it takes a lock
whenever it manipulates the set of Drainable objects since SimObjects
in different threads may create Drainable objects
dynamically. Similarly, the drain counter is now an atomic_uint, which
ensures that it is manipulated correctly when objects signal that they
are done draining.
A nice side effect of these changes is that it makes the drain state
changes stricter, which the simulation scripts can exploit to avoid
redundant drains.
The memWriteback() and memInvalidate() calls used to live in the
Serializable interface. In this series of patches, the Serializable
interface will be redesigned to make serialization independent of the
object graph and always work on the entire simulator. This means that
the Serialization interface won't be useful to perform maintenance of
the caches in a sub-graph of the entire SimObject graph. This
changeset moves these memory maintenance methods to the SimObject
interface instead.
The drain state enum is currently a part of the Drainable
interface. The same state machine will be used by the DrainManager to
identify the global state of the simulator. Make the drain state a
global typed enum to better cater for this usage scenario.
When the Python helper code switches CPU models, it sometimes also
needs to change the memory mode of the simulator. When this happens,
it accidentally tried to drain the simulator despite having done so
already. This changeset removes the redundant drain.
Serialize pixels as unsigned 32 bit integers by adding the required
to_number() and stream operators. This is used by the FrameBuffer,
which now implements the Serializable interface. Users of frame
buffers are expected to serialize it into its own section by calling
serializeSection().
Events expected to be unserialized using an event-specific
unserializeEvent call. This call was never actually used, which meant
the events relying on it never got unserialized (or scheduled after
unserialization).
Instead of relying on a custom call, we now use the normal
serialization code again. In order to schedule the event correctly,
the parrent object is expected to use the
EventQueue::checkpointReschedule() call. This happens automatically
for events that are serialized using the AutoSerialize mechanism.
Objects that are can be serialized are supposed to inherit from the
Serializable class. This class is meant to provide a unified API for
such objects. However, so far it has mainly been used by SimObjects
due to some fundamental design limitations. This changeset redesigns
to the serialization interface to make it more generic and hide the
underlying checkpoint storage. Specifically:
* Add a set of APIs to serialize into a subsection of the current
object. Previously, objects that needed this functionality would
use ad-hoc solutions using nameOut() and section name
generation. In the new world, an object that implements the
interface has the methods serializeSection() and
unserializeSection() that serialize into a named /subsection/ of
the current object. Calling serialize() serializes an object into
the current section.
* Move the name() method from Serializable to SimObject as it is no
longer needed for serialization. The fully qualified section name
is generated by the main serialization code on the fly as objects
serialize sub-objects.
* Add a scoped ScopedCheckpointSection helper class. Some objects
need to serialize data structures, that are not deriving from
Serializable, into subsections. Previously, this was done using
nameOut() and manual section name generation. To simplify this,
this changeset introduces a ScopedCheckpointSection() helper
class. When this class is instantiated, it adds a new /subsection/
and subsequent serialization calls during the lifetime of this
helper class happen inside this section (or a subsection in case
of nested sections).
* The serialize() call is now const which prevents accidental state
manipulation during serialization. Objects that rely on modifying
state can use the serializeOld() call instead. The default
implementation simply calls serialize(). Note: The old-style calls
need to be explicitly called using the
serializeOld()/serializeSectionOld() style APIs. These are used by
default when serializing SimObjects.
* Both the input and output checkpoints now use their own named
types. This hides underlying checkpoint implementation from
objects that need checkpointing and makes it easier to change the
underlying checkpoint storage code.
All x87 misc registers are implemented in an array of 64 bit values
but in real hardware the size of some of these registers is smaller.
Previsouly all 64 bits where incorrectly set and then later read. To
ensure correctness we mask the value in setMiscRegNoEffect to write
only the valid bits.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch drops the NetworkMessage class. The relevant data members and functions
have been moved to the Message class, which was the parent of NetworkMessage.
The accessor function getDestination() for Destination variable in the
coherence message clashes with the getDestination() that is part of the Message
class. Hence the name change.
This structure's only purpose was to provide a comparison function for
ordering messages in the MessageBuffer. The comparison function is now
being moved to the Message class itself. So we no longer require this
structure.
This patch increases the default read/write buffer sizes for the DDR4
controller config to values that are more suitable for the high
bandwidth and high bank count.
This patch updates the command arbitration so that bank group timing
as well as rank-to-rank delays will be taken into account. The
resulting arbitration no longer selects commands (prepped or not) that
cannot issue seamlessly if there are commands that can issue
back-to-back, minimizing the effect of rank-to-rank (tCS) & same bank
group (tCCD_L) delays.
The arbitration selects a new command based on the following priority.
Within each priority band, the arbitration will use FCFS to select the
appropriate command:
1) Bank is prepped and burst can issue seamlessly, without a bubble
2) Bank is not prepped, but can prep and issue seamlessly, without a
bubble
3) Bank is prepped but burst cannot issue seamlessly. In this case, a
bubble will occur on the bus
Thus, to enable more parallelism in subsequent selections, an
unprepped packet is given higher priority if the bank prep can be
hidden. If the bank prep cannot be hidden, the selection logic will
choose a prepped packet that cannot issue seamlessly if one exist.
Otherwise, the default selection will choose the packet with the
minimum bank prep delay.
This patch adds a simple lookup structure to avoid iterating over the
write queue to find read matches, and for the merging of write
bursts. Instead of relying on iteration we simply store a set of
currently-buffered write-burst addresses and compare against
these. For the reads we still perform the iteration if we have a
match. For the writes, we rely entirely on the set. Note that there
are corner-cases where sub-bursts would actually not be mergeable
without a read-modify-write. We ignore these cases and opt for speed.
This patch changes how the crossbar classes deal with
responses. Instead of forwarding responses directly and burdening the
neighbouring modules in paying for the latency (through the
pkt->headerDelay), we now queue them before sending them.
The coherency protocol is not affected as requests and any snoop
requests/responses are still passed on in zero time. Thus, the
responses end up paying for any header delay accumulated when passing
through the crossbar. Any latency incurred on the request path will be
paid for on the response side, if no other module has dealt with it.
As a result of this patch, responses are returned at a later
point. This affects the number of outstanding transactions, and quite
a few regressions see an impact in blocking due to no MSHRs, increased
cache-miss latencies, etc.
Going forward we should be able to use the same concept also for snoop
responses, and any request that is not an express snoop.
This patch takes the final step in removing the is_top_level parameter
from the cache. With the recent changes to read requests and write
invalidations, the parameter is no longer needed, and consequently
removed.
This also means that asymmetric cache hierarchies are now fully
supported (and we are actually using them already with L1 caches, but
no table-walker caches, connected to a shared L2).
WriteInvalidateReq ensures that a whole-line write does not incur the
cost of first doing a read exclusive, only to later overwrite the
data. This patch splits the existing WriteInvalidateReq into a
WriteLineReq, which is done locally, and an InvalidateReq that is sent
out throughout the memory system. The WriteLineReq re-uses the normal
WriteResp.
The change allows us to better express the difference between the
cache that is performing the write, and the ones that are merely
invalidating. As a consequence, we no longer have to rely on the
isTopLevel flag. Moreover, the actual memory in the system does not
see the intitial write, only the writeback. We were marking the
written line as dirty already, so there is really no need to also push
the write all the way to the memory.
The overall flow of the write-invalidate operation remains the same,
i.e. the operation is only carried out once the response for the
invalidate comes back. This patch adds the InvalidateResp for this
very reason.
This patch adds two new read requests packets:
ReadCleanReq - For a cache to explicitly request clean data. The
response is thus exclusive or shared, but not owned or modified. The
read-only caches (see previous patch) use this request type to ensure
they do not get dirty data.
ReadSharedReq - We add this to distinguish cache read requests from
those issued by other masters, such as devices and CPUs. Thus, devices
use ReadReq, and caches use ReadCleanReq, ReadExReq, or
ReadSharedReq. For the latter, the response can be any state, shared,
exclusive, owned or even modified.
Both ReadCleanReq and ReadSharedReq re-use the normal ReadResp. The
two transactions are aligned with the emerging cache-coherent TLM
standard and the AMBA nomenclature.
With this change, the normal ReadReq should never be used by a cache,
and is reserved for the actual (non-caching) masters in the system. We
thus have a way of identifying if a request came from a cache or
not. The introduction of ReadSharedReq thus removes the need for the
current isTopLevel hack, and also allows us to stop relying on
checking the packet size to determine if the source is a cache or
not. This is fixed in follow-on patches.
This patch adds a parameter to the BaseCache to enable a read-only
cache, for example for the instruction cache, or table-walker cache
(not for x86). A number of checks are put in place in the code to
ensure a read-only cache does not end up with dirty data.
A follow-on patch adds suitable read requests to allow a read-only
cache to explicitly ask for clean data.
This patch adds eviction notices to the caches, to provide accurate
tracking of cache blocks in snoop filters. We add the CleanEvict
message to the memory heirarchy and use both CleanEvicts and
Writebacks with BLOCK_CACHED flags to propagate notice of clean and
dirty evictions respectively, down the memory hierarchy. Note that the
BLOCK_CACHED flag indicates whether there exist any copies of the
evicted block in the caches above the evicting cache.
The purpose of the CleanEvict message is to notify snoop filters of
silent evictions in the relevant caches. The CleanEvict message
behaves much like a Writeback. CleanEvict is a write and a request but
unlike a Writeback, CleanEvict does not have data and does not need
exclusive access to the block. The cache generates the CleanEvict
message on a fill resulting in eviction of a clean block. Before
travelling downwards CleanEvict requests generate zero-time snoop
requests to check if the same block is cached in upper levels of the
memory heirarchy. If the block exists, the cache discards the
CleanEvict message. The snoops check the tags, writeback queue and the
MSHRs of upper level caches in a manner similar to snoops generated
from HardPFReqs. Currently CleanEvicts keep travelling towards main
memory unless they encounter the block corresponding to their address
or reach main memory (since we have no well defined point of
serialisation). Main memory simply discards CleanEvict messages.
We have modified the behavior of Writebacks, such that they generate
snoops to check for the presence of blocks in upper level caches. It
is possible in our current implmentation for a lower level cache to be
writing back a block while a shared copy of the same block exists in
the upper level cache. If the snoops find the same block in upper
level caches, we set the BLOCK_CACHED flag in the Writeback message.
We have also added logic to account for interaction of other message
types with CleanEvicts waiting in the writeback queue. A simple
example is of a response arriving at a cache removing any CleanEvicts
to the same address from the cache's writeback queue.
This patch fixes an issue which is very wide spread in the codebase,
causing sporadic linking failures. The issue is that we declare static
const class variables in the header, without any definition (as part
of a source file). In most cases the compiler propagates the value and
we have no issues. However, especially for less optimising builds such
as debug, we get sporadic linking failures due to undefined
references.
This patch fixes the Request class, by turning the static const flags
and master IDs into C++11 typed enums.
All the object loaders directly examine the (already completely loaded
by object_file.cc) memory image. There is no current motivation to
keep the fd around.
This patch updates the compiler minimum requirement to gcc 4.7 and
clang 3.1, thus allowing:
1. Explicit virtual overrides (no need for M5_ATTR_OVERRIDE)
2. Non-static data member initializers
3. Template aliases
4. Delegating constructors
This patch also enables a transition from --std=c++0x to --std=c++11.
Remove the assert when adding a port to the RubyPort retry list.
Instead of asserting, just ignore the added port, since it's
already on the list.
Without this patch, Ruby+detailed fails for even the simplest tests
Snoop packets share the request pointer with the originating
packets. We need to ensure that the snoop packet destruction does not
delete the request. Snoops are used for reads, invalidations,
HardPFReqs, Writebacks and CleansEvicts. Reads, invalidations, and
HardPFReqs need a response so their snoops do not delete the
request. For Writebacks and CleanEvicts we need to check explicitly
for whethere the current packet is an express snoop, in whcih case do
not delete the request.
There seems to have been a debug print left in when the original ARMv8
support was merged in. This printout is performed every time you
initialize a hardware thread, and it prints raw pointers, so it always
causes diffs in the regression. This patch removes the debug print.
The flush() method in CircleBuf resets the state of the circular
buffer, but fails to set size to zero. This obviously confuses code
that tries to determine the amount of data in the buffer. Set the size
to zero on flush.
Fixes missed forward eviction to CPU. With the O3CPU this can lead to load-load
reordering, as the LQ is never notified of the invalidate.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
A single HMC-2500 x32 model based on:
[1] DRAMSpec: a high-level DRAM bank modelling tool developed at the University
of Kaiserslautern. This high level tool uses RC (resistance-capacitance) and CV
(capacitance-voltage) models to estimate the DRAM bank latency and power
numbers.
[2] A Logic-base Interconnect for Supporting Near Memory Computation in the
Hybrid Memory Cube (E. Azarkhish et. al) Assumed for the HMC model is a 30 nm
technology node. The modelled HMC consists of a 4 Gbit part with 4 layers
connected with TSVs. Each layer has 16 vaults and each vault consists of 2
banks per layer. In order to be able to use the same controller used for 2D
DRAM generations for HMC, the following analogy is done: Channel (DDR) => Vault
(HMC) device_size (DDR) => size of a single layer in a vault ranks per channel
(DDR) => number of layers banks per rank (DDR) => banks per layer devices per
rank (DDR) => devices per layer ( 1 for HMC). The parameters for which no
input is available are inherited from the DDR3 configuration.
put O_DIRECT under ifdefs -- this fixes build for MacOSX.
Also use correct class for arm64 openFlagTable.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This changeset adds support for aarch64 in kvm. The CPU module
supports both checkpointing and online CPU model switching as long as
no devices are simulated by the host kernel. It currently has the
following limitations:
* The system register based generic timer can only be simulated by
the host kernel. Workaround: Use a memory mapped timer instead to
simulate the timer in gem5.
* Simulating devices (e.g., the generic timer) in the host kernel
requires that the host kernel also simulates the GIC.
* ID registers in the host and in gem5 must match for switching
between simulated CPUs and KVM. This is particularly important
for ID registers describing memory system capabilities (e.g.,
ASID size, physical address size).
* Switching between a virtualized CPU and a simulated CPU is
currently not supported if in-kernel device emulation is
used. This could be worked around by adding support for switching
to the gem5 (e.g., the KvmGic) side of the device models. A
simpler workaround is to avoid in-kernel device models
altogether.
This changeset adds a GIC implementation that uses the kernel's
built-in support for simulating the interrupt controller. Since there
is currently no support for state transfer between gem5 and the
kernel, the device model does not support serialization and CPU
switching (which would require switching to a gem5-simulated GIC).
There are cases (particularly when attaching GDB) when instruction
events are scheduled at the current instruction tick. This used to
trigger an assertion error in kvm. This changeset adds a check for
this condition and forces KVM to do a quick entry that completes any
pending IO operations, but does not execute any new instructions,
before servicing the event. We could check if we need to enter KVM at
all, but forcing a quick entry is makes the code slightly cleaner and
does not hurt correctness (performance is hardly an issue in these
cases).
This changeset moves the ARM-specific KVM CPU implementation to
arch/arm/kvm/. This change is expected to keep the source tree
somewhat cleaner as we start adding support for ARMv8 and KVM
in-kernel interrupt controller simulation.
--HG--
rename : src/cpu/kvm/ArmKvmCPU.py => src/arch/arm/kvm/ArmKvmCPU.py
rename : src/cpu/kvm/arm_cpu.cc => src/arch/arm/kvm/arm_cpu.cc
rename : src/cpu/kvm/arm_cpu.hh => src/arch/arm/kvm/arm_cpu.hh
This patch changes how the address range calculates intersection such
that a system can have a number of non-overlapping interleaved ranges
without complaining. Without this patch we end up with a panic.
The MinorCPU would count bubbles in Execute::issue as part of
the num_insts_issued and so sometimes reach the instruction
issue limit incorrectly.
Fixed by checking for a bubble in one new place.
A step towards removing RubyMemoryControl and shift users to
DRAMCtrl. The latter is faster, more representative, very versatile,
and is integrated with power models.
There are cases when we don't want to use a system register mapped
generic timer, but can't use the SP804. For example, when using KVM on
aarch64, we want to intercept accesses to the generic timer, but can't
do so if it is using the system register interface. In such cases,
we need to use a memory-mapped generic timer.
This changeset adds a device model that implements the memory mapped
generic timer interface. The current implementation only supports a
single frame (i.e., one virtual timer and one physical timer).
The ArmSystem class has a parameter to indicate whether it is
configured to use the generic timer extension or not. This parameter
doesn't affect any feature flags in the current implementation and is
therefore completely unnecessary. In fact, we usually don't set it
even if a system has a generic timer. If we ever need to check if
there is a generic timer present, we should just request a pointer and
check if it is non-null instead.
The generic timer model currently does not support virtual
counters. Virtual and physical counters both tick with the same
frequency. However, virtual timers allow a hypervisor to set an offset
that is subtracted from the counter when it is read. This enables the
hypervisor to present a time base that ticks with virtual time in the
VM (i.e., doesn't tick when the VM isn't running). Modern Linux
kernels generally assume that virtual counters exist and try to use
them by default.
This changeset cleans up the generic timer a bit and moves most of the
register juggling from the ISA code into a separate class in the same
source file as the rest of the generic timer. It also removes the
assumption that there is always 8 or fewer CPUs in the system. Instead
of having a fixed limit, we now instantiate per-core timers as they
are requested. This is all in preparation for other patches that add
support for virtual timers and a memory mapped interface.
The register dumping code in kvm tries to print the bytes in large
registers (128 bits and larger) instead of printing them as hex. This
changeset fixes that.
Some versions of the kernel incorrectly swap the red and blue color
select registers. This changeset adds a workaround for that by
swapping them when instantiating a PixelConverter.
Currently, frame buffer handling in gem5 is quite ad hoc. In practice,
we pass around naked pointers to raw pixel data and expect consumers
to convert frame buffers using the (broken) VideoConverter.
This changeset completely redesigns the way we handle frame buffers
internally. In summary, it fixes several color conversion bugs, adds
support for more color formats (e.g., big endian), and makes the code
base easier to follow.
In the new world, gem5 always represents pixel data using the Pixel
struct when pixels need to be passed between different classes (e.g.,
a display controller and the VNC server). Producers of entire frames
(e.g., display controllers) should use the FrameBuffer class to
represent a frame.
Frame producers are expected to create one instance of the FrameBuffer
class in their constructors and register it with its consumers
once. Consumers are expected to check the dimensions of the frame
buffer when they consume it.
Conversion between the external representation and the internal
representation is supported for all common "true color" RGB formats of
up to 32-bit color depth. The external pixel representation is
expected to be between 1 and 4 bytes in either big endian or little
endian. Color channels are assumed to be contiguous ranges of bits
within each pixel word. The external pixel value is scaled to an 8-bit
internal representation using a floating multiplication to map it to
the entire 8-bit range.
The bitmap generation code is hard to follow and incorrectly uses the
size of an enum member to calculate the size of a pixel. This
changeset cleans up the code and adds some documentation.
The processes of warming up and cooling down Ruby caches are simulation-wide
processes, not just RubySystem instance-specific processes. Thus, the warm-up
and cool-down variables should be globally visible to any Ruby components
participating in either process. Make these variables static members and track
the warm-up and cool-down processes as appropriate.
This patch also has two side benefits:
1) It removes references to the RubySystem g_system_ptr, which are problematic
for allowing multiple RubySystem instances in a single simulation. Warmup and
cooldown variables being static (global) reduces the need for instance-specific
dereferences through the RubySystem.
2) From the AbstractController, it removes local RubySystem pointers, which are
used inconsistently with other uses of the RubySystem: 11 other uses reference
the RubySystem with the g_system_ptr. Only sequencers have local pointers.
Three minor issues are resolved:
1. Apparently gcc 5.1 does not like negation of booleans followed by
bitwise AND.
2. Somehow the compiler also gets confused and warns about
NoopMachInst being unused (removing it causes compilation errors
though). Most likely a compiler bug.
3. There seems to be a number of instances where loop unrolling causes
false positives for the array-bounds check. For now, switch to
std::array. Potentially we could disable the warning for newer gcc
versions, but switching to std::array is probably a good move in
any case.
The system class currently clears the vector of active CPUs in
initState(). CPUs are added to the list by registerThreadContext()
which is called from BaseCPU::init(). This obviously breaks when the
System object is initialized after the CPUs. This changeset removes
the offending clear() call since the list will be empty after it has
been instantiated anyway.
The current ignoreWarnOnceFunc doesn't really work as expected,
since it will only generate one warning total, for whichever
"warn-once" syscall is invoked first. This patch fixes that
behavior by keeping a "warned" flag in the SyscallDesc object,
allowing suitably flagged syscalls to warn exactly once per
syscall.
Sometimes, we need to defer an express snoop in an MSHR, but the original
request might complete and deallocate the original pkt->req. In those cases,
create a copy of the request so that someone who is inspecting the delayed
snoop can also inspect the request still. All of this is rather hacky, but the
allocation / linking and general life-time management of Packet and Request is
rather tricky. Deleting the copy is another tricky area, testing so far has
shown that the right copy is deleted at the right time.
We currently assume that all uncacheable memory accesses are strictly
ordered. Instead of always enforcing strict ordering, we now only
enforce it if the required memory type is device memory or strongly
ordered memory.
The Request::UNCACHEABLE flag currently has two different
functions. The first, and obvious, function is to prevent the memory
system from caching data in the request. The second function is to
prevent reordering and speculation in CPU models.
This changeset gives the order/speculation requirement a separate flag
(Request::STRICT_ORDER). This flag prevents CPU models from doing the
following optimizations:
* Speculation: CPU models are not allowed to issue speculative
loads.
* Write combining: CPU models and caches are not allowed to merge
writes to the same cache line.
Note: The memory system may still reorder accesses unless the
UNCACHEABLE flag is set. It is therefore expected that the
STRICT_ORDER flag is combined with the UNCACHEABLE flag to prevent
this behavior.
With the recent patches addressing how we deal with uncacheable
accesses there is no longer need for the work arounds put in place to
enforce certain sections of memory to be uncacheable during boot.
This patch takes a last step in fixing issues related to uncacheable
accesses. We do not separate uncacheable memory from uncacheable
devices, and in cases where it is really memory, there are valid
scenarios where we need to snoop since we do not support cache
maintenance instructions (yet). On snooping an uncacheable access we
thus provide data if possible. In essence this makes uncacheable
accesses IO coherent.
The snoop filter is also queried to steer the snoops, but not updated
since the uncacheable accesses do not allocate a block.
This patch simplifies the overall CPU by changing the TLB caches such
that they do not forward snoops to the table walker port(s). Note that
only ARM and X86 are affected.
There is no reason for the ports to snoop as they do not actually take
any action, and from a performance point of view we are better of not
snooping more than we have to.
Should it at a later point be required to snoop for a particular TLB
design it is easy enough to add it back.
This patch ensures that we pass on information about a packet being
shared (rather than exclusive), when forwarding a packet downstream.
Without this patch there is a risk that a downstream cache considers
the line exclusive when it really isn't.
This patch adds a missing counter update for the uncacheable
accesses. By updating this counter we also get a meaningful average
latency for uncacheable accesses (previously inf).
This patch changes the cache implementation to rely on virtual methods
rather than using the replacement policy as a template argument.
There is no impact on the simulation performance, and overall the
changes make it easier to modify (and subclass) the cache and/or
replacement policy.
This patch fixes a recent issue with gcc 4.9 (and possibly more) being
convinced that indices outside the array bounds are used when
initialising the FUPool members.
Both open_adaptive and close_adaptive page polices keep the page
open if a row hit is found. If a row hit is not found, close_adaptive
page policy precharges the row, and open_adaptive policy precharges
the row only if there is a bank conflict request waiting in the queue.
This patch makes the checks for above conditions simpler.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Currently, each op class has a parameter issueLat that denotes the cycles after
which another op of the same class can be issued. As of now, this latency can
either be one cycle (fully pipelined) or same as execution latency of the op
(not at all pipelined). The fact that issueLat is a parameter of type Cycles
makes one believe that it can be set to any value. To avoid the confusion, the
parameter is being renamed as 'pipelined' with type boolean. If set to true,
the op would execute in a fully pipelined fashion. Otherwise, it would execute
in an unpipelined fashion.
This patch sets the default latency of the division microop to a single cycle
on x86. This is because the division instructions DIV and IDIV have been
implemented as loops of div microops, where each microop computes a single bit
of the quotient.
Same exception is raised whether division with zero is performed or the
quotient is greater than the maximum value that the provided space can hold.
Divide-by-Zero is the AMD terminology, while Divide-Error is Intel's.
This patch introduces a UFS host controller and a UFS device. More
information about the UFS standard can be found at the JEDEC site:
http://www.jedec.org/standards-documents/results/jesd220
Note that the model does not implement the complete standard, and as
such is not an actual implementation of UFS. The following SCSI
commands are implemented: inquiry, read, read capacity, report LUNs,
start/stop, test unit ready, verify, write, format unit, send
diagnostic, synchronize cache, mode select, mode sense, request sense,
unmap, write buffer and read buffer. This is sufficient for usage with
Linux and Android.
To interact with this model a kernel version 3.9 or above is
needed.
This adds a NAND flash timing model. This model takes the number of
planes into account and is ultimately intended to be used as a
high-level performance model for any device using flash. To access the
memory, use either readMemory or writeMemory.
To make use of the model you will need an interface model
such as UFSHostDevice, which is part of a separate patch.
At the moment the flash device is part of the ARM device tree since
the only use if the UFSHostDevice, and that in turn relies on the ARM
GIC.
This patch adds an I2C bus and base device. I2C is used to connect a
variety of sensors, and this patch serves as a starting point to
enable a range of I2C devices.
This patch fixes a few small issues to ensure gem5 compiles when using
gcc 5.1.
First, the GDB_REG_BYTES in the RemoteGDB header are, rather
surprisingly, flagged as unused for both ARM and X86. Removing them,
however, causes compilation errors as they are actually used in the
source file. Moving the constant into the class definition fixes the
issue. Possibly a gcc bug.
Second, we have an unused EthPktData constructor using auto_ptr, and
the latter is deprecated. Since the code is never used it is simply
removed.
The o3 cpu instruction queue model uses the count variable to track the number
of unissued instructions in the queue. Previously, the squash method used
this variable to avoid executing the doSquash method when there were no
unissued instructions in the pipeline. A corner case problem exists when
only issued instructions exist in the pipeline and a squash occurs; the
doSquash code is not invoked and subsequently does not clean up state properly.
This patch takes the final step in removing the InOrderCPU from the
tree. Rest in peace.
The MinorCPU is now used to model an in-order microarchitecture, and
long term the MinorCPU will eventually be renamed InOrderCPU.
This patch ensures that the CPU progress Event is triggered for the new set of
switched_cpus that get scheduled (e.g. during fast-forwarding). it also avoids
printing the interval state if the cpu is currently switched out.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Restoring from a checkpoint with ruby + the DRAMCtrl memory model was not
working, because ruby and DRAMCtrl disagreed on the current tick during warmup.
Since there is no reason to do timing requests during warmup, use functional
requests instead.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch adds an example configuration in ext/sst/tests/ that allows
an SST/gem5 instance to simulate a 4-core AArch64 system with SST's
memHierarchy components providing all the caches and memories.
Restoring from a checkpoint fails if either the RTC or the RTC Timer
Interrrupt event is disabled. The restored machine tried incorrectly
to schedule the next event with negative offset.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Add 32-bit access width for PrimaryTiming register and 16bit for UDMAControl
register as FreeBSD required.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
The totalInstructions counter is only incremented when the whole instruction is
commited and not on every microop. It was incorrectly reset in atomic and
timing cpus.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>"
When running with the Exec flag, the mwait instruction attempted
to print out its source registers, which were never actually
initialized. This led to sporadic assertion failures when the
value stored there was invalid.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
The stride prefetcher had a hardcoded number of contexts (i.e. master-IDs)
that it could handle. Since master IDs need to be unique per system, and
every core, cache etc. requires a separate master port, a static limit on
these does not make much sense.
Instead, this patch adds a small hash map that will map all master IDs to
the right prefetch state and dynamically allocates new state for new master
IDs.
This patch changes the order of writeback allocation such that any
writebacks resulting from a tag lookup (e.g. for an uncacheable
access), are added to the writebuffer before any new MSHR entries are
allocated. This ensures that the writebacks logically precedes the new
allocations.
The patch also changes the uncacheable flush to use proper timed (or
atomic) writebacks, as opposed to functional writes.
This patch simplifies the code dealing with uncacheable timing
accesses, aiming to align it with the existing miss handling. Similar
to what we do in atomic, a timing request now goes through
Cache::access (where the block is also flushed), and then proceeds to
ignore any existing MSHR for the block in question. This unifies the
flow for cacheable and uncacheable accesses, and for atomic and timing.
This patch changes how we search for matching MSHRs, ignoring any MSHR
that is allocated for an uncacheable access. By doing so, this patch
fixes a corner case in the MSHRs where incorrect data ended up being
copied into a (cacheable) read packet due to a first uncacheable MSHR
target of size 4, followed by a cacheable target to the same MSHR of
size 64. The latter target was filled with nonsense data.
This patch removes the no-longer-needed
allocateUncachedReadBuffer. Besides the checks it is exactly the same
as allocateMissBuffer and thus provides no value.
This patch aligns all MSHR queue entries to block boundaries to
simplify checks for matches. Previously there were corner cases that
could lead to existing entries not being identified as matches.
There are, rather alarmingly, a few regressions that change with this
patch.
This patch subsumes the PREFETCH_SNOOP_SQUASH flag with the more
generic BLOCK_CACHED flag. Future patches implementing cache eviction
messages can use the BLOCK_CACHED flag in almost the same manner as
hardware prefetches use the PREFETCH_SNOOP_SQUASH flag. The
PREFTECH_SNOOP_FLAG is set if the prefetch target is found in the tags
or the MSHRs in any state, so we are simply replacing calls to
setPrefetchSquashed() with setBlockCached(). The case of where the
prefetch target is found in the writeback MSHRs of upper level caches
continues to be covered by the MEM_INHIBIT flag.
Currently if there are shell special characters in a
command-line argument, you can't copy and paste the
echoed command line onto a shell prompt because the
characters aren't quoted properly. This patch fixes
that problem.
This patch accomplishes two things:
1. Makes simulate()'s GlobalSimLoopExitEvent a singleton reused
across calls. This is slightly more efficient than recreating
it every time.
2. Gives callers to simulate() (especially other simulators) a
foolproof way of knowing that the simulation period ended
successfully by hitting the limit event. They can call
getLimitEvent() and compare it to the return
value of simulate().
This change was motivated by an ongoing effort to integrate gem5
and SST, with SST as the master sim and gem5 as the slave sim.
This patch adds a new PIO-accessible GICv2m shim. This shim has a PIO
slave port on one side, and SPI 'wires' on the other. It accepts MSIs
from the system and triggers SPIs on the GIC. It is configurable with
a number of frames, each of which has a number of SPIs and a base SPI
offset.
A Linux driver for GICv2m is available upstream.
This patch removes the code that added this magic register. A
follow-up patch provides a GICv2m MSI shim that gives the same
functionality in a standard ARM system architecture way.
Fix erroneous message format for fatal error.
Previously, code did not have type indicator (% instead of %d).
Also removed redundant fatal check.
Ran modified sweep.py with in range and out of range values to test.
The CommMonitor by default only allows memory traces to be gathered in
timing mode. This patch allows memory traces to be gathered in atomic
mode if all one needs is a functional trace of memory addresses used
and timing information is of a secondary concern.
For some reason we were checking mshr->hasTargets() even though
we had already called mshr->getTarget() unconditionally earlier
in the same function (which asserts if there are no targets).
Get rid of this useless check, and while we're at it get rid
of the redundant call to mshr->getTarget(), since we still have
the value saved in a local var.
Refactor the way that specific MemCmd values are generated for packets.
The new approach is a little more elegant in that we assign the right
value up front, and it's also more amenable to non-heap-allocated
Packet objects.
Also replaced the code in the Minor model that was still doing it the
ad-hoc way.
This is basically a refinement of http://repo.gem5.org/gem5/rev/711eb0e64249.
The 'if (writebacks.size)' check was redundant, because
writeBuffer.findMatches() would return false if the
writebacks list was empty.
Also renamed 'mshr' to 'wb_entry' in this context since
we are pointing at a writebuffer entry and not an MSHR
(even though it's the same C++ class).
The variable is used in only one place and a whole new function setNextStatus()
has been defined just to compute the value of the variable. Instead of calling
the function, the value is now computed in the loop that preceded the function
call.
This patch changes all the DPRINTF messages in the cache to use
'%#llx' every time a packet address is printed. The inclusion of '#'
ensures '0x' is prepended, and since the address type is a uint64_t %x
really should be %llx.
This patch fixes a rather subtle issue in the sending of MSHR requests
in the cache, where the logic previously did not check for conflicts
between the MSRH queue and the write queue when requests were not
ready. The correct thing to do is to always check, since not having a
ready MSHR does not guarantee that there is no conflict.
The underlying problem seems to have slipped past due to the symmetric
timings used for the write queue and MSHR queue. However, with the
recent timing changes the bug caused regressions to fail.
This patch changes the valid-bytes start/end to a proper byte
mask. With the changes in timing introduced in previous patches there
are more packets waiting in queues, and there are regressions using
the checker CPU failing due to non-contigous read data being found in
the various cache queues.
This patch also adds some more comments explaining what is going on,
and adds the fourth and missing case to Packet::checkFunctional.
By default, the packet queue is ordered by the ticks of the to-be-sent
packages. With the recent modifications of packages sinking their header time
when their resposne leaves the caches, there could be cases of MSHR targets
being allocated and ordered A, B, but their responses being sent out in the
order B,A. This led to inconsistencies in bus traffic, in particular the snoop
filter observing first a ReadExResp and later a ReadRespWithInv. Logically,
these were ordered the other way around behind the MSHR, but due to the timing
adjustments when inserting into the PacketQueue, they were sent out in the
wrong order on the bus, confusing the snoop filter.
This patch adds a flag (off by default) such that these special cases can
request in-order insertion into the packet queue, which might offset timing
slighty. This is expected to occur rarely and not affect timing results.
This patch makes the caches and memory controllers consume the delay
that is annotated to a packet by the crossbar. Previously many
components simply threw these delays away. Note that the devices still
do not pay for these delays.
This patch introduces a few subclasses to the CoherentXBar and
NoncoherentXBar to distinguish the different uses in the system. We
use the crossbar in a wide range of places: interfacing cores to the
L2, as a system interconnect, connecting I/O and peripherals,
etc. Needless to say, these crossbars have very different performance,
and the clock frequency alone is not enough to distinguish these
scenarios.
Instead of trying to capture every possible case, this patch
introduces dedicated subclasses for the three primary use-cases:
L2XBar, SystemXBar and IOXbar. More can be added if needed, and the
defaults can be overridden.
This patch introduces latencies in crossbar that were neglected
before. In particular, it adds three parameters in crossbar model:
front_end_latency, forward_latency, and response_latency. Along with
these parameters, three corresponding members are added:
frontEndLatency, forwardLatency, and responseLatency. The coherent
crossbar has an additional snoop_response_latency.
The latency of the request path through the xbar is set as
--> frontEndLatency + forwardLatency
In case the snoop filter is enabled, the request path latency is charged
also by look-up latency of the snoop filter.
--> frontEndLatency + SF(lookupLatency) + forwardLatency.
The latency of the response path through the xbar is set instead as
--> responseLatency.
In case of snoop response, if the response is treated as a normal response
the latency associated is again
--> responseLatency;
If instead it is forwarded as snoop response we add an additional variable
+ snoopResponseLatency
and the latency associated is
--> snoopResponseLatency;
Furthermore, this patch lets the crossbar progress on the next clock
edge after an unused retry, changing the time the crossbar considers
itself busy after sending a retry that was not acted upon.
The ARM PL011 UART model didn't clear and raise interrupts
correctly. This changeset rewrites the whole interrupt handling and
makes it both simpler and fixes several cases where the correct
interrupts weren't raised or cleared. Additionally, it cleans up many
other aspects of the code.
This patch changes how the MMU and table walkers are created such that
a single port is used to connect the MMU and the TLBs to the memory
system. Previously two ports were needed as there are two table walker
objects (stage one and stage two), and they both had a port. Now the
port itself is moved to the Stage2MMU, and each TableWalker is simply
using the port from the parent.
By using the same port we also remove the need for having an
additional crossbar joining the two ports before the walker cache or
the L2. This simplifies the creation of the CPU cache topology in
BaseCPU.py considerably. Moreover, for naming and symmetry reasons,
the TLB walker port is connected through the stage-one table walker
thus making the naming identical to x86. Along the same line, we use
the stage-one table walker to generate the master id that is used by
all TLB-related requests.
Now, prior to the renaming, the instruction requests the exact amount of
registers it will need, and the rename_map decides whether the instruction is
allowed to proceed or not.
This patch fixes a long-standing isue with the port flow
control. Before this patch the retry mechanism was shared between all
different packet classes. As a result, a snoop response could get
stuck behind a request waiting for a retry, even if the send/recv
functions were split. This caused message-dependent deadlocks in
stress-test scenarios.
The patch splits the retry into one per packet (message) class. Thus,
sendTimingReq has a corresponding recvReqRetry, sendTimingResp has
recvRespRetry etc. Most of the changes to the code involve simply
clarifying what type of request a specific object was accepting.
The biggest change in functionality is in the cache downstream packet
queue, facing the memory. This queue was shared by requests and snoop
responses, and it is now split into two queues, each with their own
flow control, but the same physical MasterPort. These changes fixes
the previously seen deadlocks.
This patch resolves a bug with hardware prefetches. Before a hardware prefetch
is sent towards the memory, the system generates a snoop request to check all
caches above the prefetch generating cache for the presence of the prefetth
target. If the prefetch target is found in the tags or the MSHRs of the upper
caches, the cache sets the prefetchSquashed flag in the snoop packet. When the
snoop packet returns with the prefetchSquashed flag set, the prefetch
generating cache deallocates the MSHR reserved for the prefetch. If the
prefetch target is found in the writeback buffer of the upper cache, the cache
sets the memInhibit flag, which signals the prefetch generating cache to
expect the data from the writeback. When the snoop packet returns with the
memInhibitAsserted flag set, it marks the allocated MSHR as inService and
waits for the data from the writeback.
If the prefetch target is found in multiple upper level caches, specifically
in the tags or MSHRs of one upper level cache and the writeback buffer of
another, the snoop packet will return with both prefetchSquashed and
memInhibitAsserted set, while the current code is not written to handle such
an outcome. Current code checks for the prefetchSquashed flag first, if it
finds the flag, it deallocates the reserved MSHR. This leads to assert failure
when the data from the writeback appears at cache. In this fix, we simply
switch the order of checks. We first check for memInhibitAsserted and then for
prefetch squashed.
Have the traffic generator add its masterID as the PC address to the
requests. That way, prefetchers (and other components) that use a PC
for request classification will see per-tester streams of requests.
This enables us to test strided prefetchers with the memchecker, too.
The ISA code sometimes stores 16-bit ASIDs as 8-bit unsigned integers
and has a couple of inverted checks that mask out the high 8 bits of
an ASID if 16-bit ASIDs have been /enabled/. This changeset fixes both
of those issues.
We curently use INTREG_X31 instead of INTREG_SPX when accessing the
stack pointer in GDB. gem5 normally uses INTREG_SPX to access the
stack pointer, which gets mapped to the stack pointer corresponding
(INTREG_SPn) to the current exception level. This changeset updates
the GDB interface to use SPX instead of X31 (which is always zero)
when transfering CPU state to gdb.
The remote GDB interface currently doesn't check if translations are
valid before reading memory. This causes a panic when GDB tries to
access unmapped memory (e.g., when getting a stack trace). There are
two reasons for this: 1) The function used to check for valid
translations (virtvalid()) doesn't work and panics on invalid
translations. 2) The method in the GDB interface used to test if a
translation is valid (RemoteGDB::acc) always returns true regardless
of the return from virtvalid().
This changeset fixes both of these issues.
Previously, the user would have to manually set access_backing_store=True
on all RubyPorts (Sequencers) in the config files.
Now, instead there is one global option that each RubyPort checks on
initialization.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
To be able to use the TrafficGen in a system with caches we need to
allow it to sink incoming snoop requests. By default the master port
panics, so silently ignore any snoops.
In highly loaded cases, reads might actually overlap with writes to the
initial memory state. The mem checker needs to detect such cases and
permit the read reading either from the writes (what it is doing now) or
read from the initial, unknown value.
This patch adds this logic.
This patch fixes a rather unfortunate oversight where the annotation
pointer was used even though it is null. Somehow the code still works,
but UBSan is rather unhappy. The use is now guarded, and the variable
is initialised in the constructor (as well as init()).
Move the (common) GIC initialization code that notifies the platform
code of the new GIC to the base class (BaseGic) instead of the Pl390
implementation.
This patch ensures we can run simulations with very large simulated
memories (at least 64 TB based on some quick runs on a Linux
workstation). In essence this allows us to efficiently deal with
sparse address maps without having to implement a redirection layer in
the backing store.
This opens up for run-time errors if we eventually exhausts the hosts
memory and swap space, but this should hopefully never happen.
This patch changes the range cache used in the global physical memory
to be an iterator so that we can use it not only as part of isMemAddr,
but also access and functionalAccess. This matches use-cases where a
core is using the atomic non-caching memory mode, and repeatedly calls
isMemAddr and access.
Linux boot on aarch32, with a single atomic CPU, is now more than 30%
faster when using "--fastmem" compared to not using the direct memory
access.
This changeset moves the pseudo instructions used to signal unknown
instructions and unimplemented instructions to the same source files
as the decoder fault.
This patch clarifies the packet timings annotated
when going through a crossbar.
The old 'firstWordDelay' is replaced by 'headerDelay' that represents
the delay associated to the delivery of the header of the packet.
The old 'lastWordDelay' is replaced by 'payloadDelay' that represents
the delay needed to processing the payload of the packet.
For now the uses and values remain identical. However, going forward
the payloadDelay will be additive, and not include the
headerDelay. Follow-on patches will make the headerDelay capture the
pipeline latency incurred in the crossbar, whereas the payloadDelay
will capture the additional serialisation delay.
This patch adds some much-needed clarity in the specification of the
cache timing. For now, hit_latency and response_latency are kept as
top-level parameters, but the cache itself has a number of local
variables to better map the individual timing variables to different
behaviours (and sub-components).
The introduced variables are:
- lookupLatency: latency of tag lookup, occuring on any access
- forwardLatency: latency that occurs in case of outbound miss
- fillLatency: latency to fill a cache block
We keep the existing responseLatency
The forwardLatency is used by allocateInternalBuffer() for:
- MSHR allocateWriteBuffer (unchached write forwarded to WriteBuffer);
- MSHR allocateMissBuffer (cacheable miss in MSHR queue);
- MSHR allocateUncachedReadBuffer (unchached read allocated in MSHR
queue)
It is our assumption that the time for the above three buffers is the
same. Similarly, for snoop responses passing through the cache we use
forwardLatency.
The MemTest class really only tests false sharing, and as such there
was a lot of old cruft that could be removed. This patch cleans up the
tester, and also makes it more clear what the assumptions are. As part
of this simplification the reference functional memory is also
removed.
The regression configs using MemTest are updated to reflect the
changes, and the stats will be bumped in a separate patch. The example
config will be updated in a separate patch due to more extensive
re-work.
In a follow-on patch a new tester will be introduced that uses the
MemChecker to implement true sharing.
The TLB-related code is generally architecture dependent and should
live in the arch directory to signify that.
--HG--
rename : src/sim/BaseTLB.py => src/arch/generic/BaseTLB.py
rename : src/sim/tlb.cc => src/arch/generic/tlb.cc
rename : src/sim/tlb.hh => src/arch/generic/tlb.hh
Gcc and clang both provide an attribute that can be used to flag a
function as deprecated at compile time. This changeset adds a gem5
compiler macro for that compiler feature. The macro can be used to
indicate that a legacy API within gem5 has been deprecated and provide
a graceful migration to the new API.
This patch fixes the CompoundFlag constructor, ensuring that it does
not dereference NULL. Doing so has undefined behaviuor, and both clang
and gcc's undefined-behaviour sanitiser was rather unhappy.
The Platform base class contains a pointer to an instance of the
System which is never initialized. This can lead to subtle bugs since
some architecture-specific platform implementations contain their own
system pointer which is normally used. However, if the platform is
accessed through a pointer to its base class, the dangling pointer
will be used instead.
This patch adds a bit of clarification around the assumptions made in
the cache when packets are sent out, and dirty responses are
pending. As part of the change, the marking of an MSHR as in service
is simplified slightly, and comments are added to explain what
assumptions are made.
This patch extends the current address interleaving with basic hashing
support. Instead of directly comparing a number of address bits with a
matching value, it is now possible to use two independent set of
address bits XOR'ed together. This avoids issues where strided address
patterns are heavily biased to a subset of the interleaved ranges.
This patch changes the DRAM channel interleaving default behaviour to
be more representative. The default address mapping (RoRaBaCoCh) moves
the channel bits towards the least significant bits, and uses 128 byte
as the default channel interleaving granularity.
These defaults can be overridden if desired, but should serve as a
sensible starting point for most use-cases.
The method Event::initialized() tests if this != NULL as a part of the
expression that tests if an event is initialized. The only case when
this check could be false is if the method is called on a null
pointer, which is illegal and leads to undefined behavior (such as
eating your pets) according to the C++ standard. Because of this,
modern compilers (specifically, recent versions of clang) warn about
this which we treat as an error. This changeset removes the redundant
check to fix said warning.
This patch changes how the timing CPU deals with processing responses,
always scheduling an event, even if it is for the current tick. This
helps to avoid situations where a new request shows up before a
response is finished in the crossbar, and also is more in line with
any realistic behaviour.
The Float param was not settable on the command line
due to a typo in the class definition in
python/m5/params.py. This corrects the typo and allows
floats to be set on the command line as intended.
While the IsFirstMicroop flag exists it was only occasionally used in the ARM
instructions that gem5 microOps and therefore couldn't be relied on to be correct.
When gem5 is a slave to another simulator and the Python is only used
to initialize the configuration (and not perform actual simulation), a
"debug start" (--debug-start) event will get freed during or immediately
after the initial Python frame's execution rather than remaining in the
event queue. This tricky patch fixes the GC issue causing this.
This patch takes the final step in removing the src and dest fields in
the packet. These fields were rather confusing in that they only
remember a single multiplexing component, and pushed the
responsibility to the bridge and caches to store the fields in a
senderstate, thus effectively creating a stack. With the recent
changes to the crossbar response routing the crossbar is now
responsible without relying on the packet fields. Thus, these
variables are now unused and can be removed.
This patch removes the source field from the ForwardResponseRecord,
but keeps the class as it is part of how the cache identifies
responses to hardware prefetches that are snooped upwards.
This patch aligns how the response routing is done in the RubyPort,
using the SenderState for both memory and I/O accesses. Before this
patch, only the I/O used the SenderState, whereas the memory accesses
relied on the src field in the packet. With this patch we shift to
using SenderState in both cases, thus not relying on the src field any
longer.
This patch removes the need for a source and destination field in the
packet by shifting the onus of the tracking to the crossbar, much like
a real implementation. This change in behaviour also means we no
longer need a SenderState to remember the source/dest when ever we
have multiple crossbars in the system. Thus, the stack that was
created by the SenderState is not needed, and each crossbar locally
tracks the response routing.
The fields in the packet are still left behind as the RubyPort (which
also acts as a crossbar) does routing based on them. In the succeeding
patches the uses of the src and dest field will be removed. Combined,
these patches improve the simulation performance by roughly 2%.
This patch fixes a minor issue in the X86 page table walker where it
ended up sending new request packets to the crossbar before the
response processing was finished (recvTimingResp is directly calling
sendTimingReq). Under certain conditions this caused the crossbar to
see illegal combinations of request/response overlap, in turn causing
problems with a slightly modified crossbar implementation.
This patch tidies up how we create and set the fields of a Request. In
essence it tries to use the constructor where possible (as opposed to
setPhys and setVirt), thus avoiding spreading the information across a
number of locations. In fact, setPhys is made private as part of this
patch, and a number of places where we callede setVirt instead uses
the appropriate constructor.
The ppCommit should notify the attached listener every time the cpu commits
a microop or non microcoded insturction. The listener can then decide
whether it will process only the last microop (eg. SimPoint probe).
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch fixes a bug where the DRAM controller tried to access the
system cacheline size before the system pointer was initialised. It
also fixes a bug where the granularity is 0 (no interleaving).
This patch corrects the FXSAVE and FXRSTOR Macroops. The actual code used for
saving/restore the FP registers is in the file but it was not used.
The FXSAVE and FXRSTOR instructions are used in the kernel for saving and
loading the state of the mmx,xmm and fpu registers.
This operation is triggered in FS by issuing a Device Not Available Fault. The
cr0 register has a TS flag that is set upon each context change. Every time a
task access any FP related register (SIMD as well) if the TS flag is set to
one, the device not available fault is issued. The kernel saves the current
state of the registers, and restore the previous state of the currently running
task.
Right now Gem5 lacks of this capability. the Device Not Available Fault is
never issued, leading to several problems when different threads share the same
CPU and SMT is not used. The PARSEC Ferret benchmark is an example of this
behavior.
In order to test this a hack in the atomic cpu code was done to detect if a
static instruction has any FP operands and the cr0 reg TS bit is set. This
check must be done in the ISA dependent code. But it seems to be tricky to
access the cr0 register while executing an instruction.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This change includes edits to Intel8254Timer to prevent counter events firing
before startup to comply with SimObject initialization call sequence.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
If two bitfields are of the same type, also implying that they have the same
first and last bit positions, the existing implementation would copy the
entire bitfield. That includes the __data member which is shared among all the
bitfields, effectively overwritting the entire bitunion.
This change also adjusts the write only signed bitfield assignment operator to
be like the unsigned version, using "using" instead of implementing it again
and calling down to the underlying implementation.
That change enables CPUID bits for features that aren't implemented in gem5.
If a simulated system tries to use those features because it was told it
could, bad things can happen.
Minor was reporting the data cache access as ".inst" accesses.
This just switches the MasterPortID to dataMasterPortId.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
added ARM aarch64 unlinkat syscall support, modeled on other <xxx>at syscalls.
This gets all of the cpu2006 int workloads passing in SE mode on aarch64.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch implements the simd128 ADDSUBPD instruction for the x86 architecture.
Tested with a simple program in assembly language which executes the
instruction. Checked that different versions of the instruction are executed
by using the execution tracing option.
Committed by: Nilay Vaish <nilay@cs.wisc.edu
This change includes edits to MC146818 timer to prevent RTC events
firing before startup to comply with SimObject initialization call sequence.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
According to Linux man pages, if writev is successful, it returns the total
number of bytes written. Otherwise, it returns an error code. Instead of
returning 0, return the result from the actual call to writev in the system
call.
The cache's MemSidePacketQueue schedules a sendEvent based upon
nextMSHRReadyTime() which is the time when the next MSHR is ready or whenever
a future prefetch is ready. However, a prefetch being ready does not guarentee
that it can obtain an MSHR. So, when all MSHRs are full,
the simulation ends up unnecessiciarly scheduling a sendEvent every picosecond
until an MSHR is finally freed and the prefetch can happen.
This patch fixes this by not signaling the prefetch ready time if the prefetch
could not be generated. The event is rescheduled as soon as a MSHR becomes
available.
Previously the code commented about an unhandled case where it might be
possible for a writeback to arrive after a prefetch was generated but
before it was sent to the memory system. I hit that case. Luckily
the prefetchSquash() logic already in the code handles dropping prefetch
request in certian circumstances.
Re-organizes the prefetcher class structure. Previously the
BasePrefetcher forced multiple assumptions on the prefetchers that
inherited from it. This patch makes the BasePrefetcher class truly
representative of base functionality. For example, the base class no
longer enforces FIFO order. Instead, prefetchers with FIFO requests
(like the existing stride and tagged prefetchers) now inherit from a
new QueuedPrefetcher base class.
Finally, the stride-based prefetcher now assumes a custimizable lookup table
(sets/ways) rather than the previous fully associative structure.
Adds a new parameter that reserves some number of MSHR entries for demand
accesses. This helps prevent prefetchers from taking all MSHRs, forcing demand
requests from the CPU to stall.
This patch adds table walker stats for:
- Walk events
- Instruction vs Data
- Page size histogram
- Wait time and service time histograms
- Pending requests histogram (per cycle) - measures dist. of L
(p(1..) = how often busy, p(0) = how often idle)
- Squashes, before starting and after completion
This patch gives the user direct influence over the number of DRAM
ranks to make it easier to tune the memory density without affecting
the bandwidth (previously the only means of scaling the device count
was through the number of channels).
The patch also adds some basic sanity checks to ensure that the number
of ranks is a power of two (since we rely on bit slices in the address
decoding).
This patch addresses an issue seen with the KVM CPU where the refresh
events scheduled by the DRAM controller forces the simulator to switch
out of the KVM mode, thus killing performance.
The current patch works around the fact that we currently have no
proper API to inform a SimObject of the mode switches. Instead we rely
on drainResume being called after any switch, and cache the previous
mode locally to be able to decide on appropriate actions.
The switcheroo regression require a minor stats bump as a result.
This patch adds rank-wise refresh to the controller, as opposed to the
channel-wide refresh currently in place. In essence each rank can be
refreshed independently, and for this to be possible the controller
is extended with a state machine per rank.
Without this patch the data bus is always idle during a refresh, as
all the ranks are refreshing at the same time. With the rank-wise
refresh it is possible to use one rank while another one is
refreshing, and thus the data bus can be kept busy.
The patch introduces a Rank class to encapsulate the state per rank,
and also shifts all the relevant banks, activation tracking etc to the
rank. The arbitration is also updated to consider the state of the rank.
This patch adds a stand-alone stack distance calculator. The stack
distance calculator is a passive SimObject that observes the addresses
passed to it. It calculates stack distances (LRU Distances) of
incoming addresses based on the partial sum hierarchy tree algorithm
described by Alamasi et al. http://doi.acm.org/10.1145/773039.773043.
For each transaction a hashtable look-up is performed. At every
non-unique transaction the tree is traversed from the leaf at the
returned index to the root, the old node is deleted from the tree, and
the sums (to the right) are collected and decremented. The collected
sum represets the stack distance of the found node. At every unique
transaction the stack distance is returned as
numeric_limits<uint64>::max().
In addition to the basic stack distance calculation, a feature to mark
an old node in the tree is added. This is useful if it is required to
see the reuse pattern. For example, Writebacks to the lower level
(e.g. membus from L2), can be marked instead of being removed from the
stack (isMarked flag of Node set to True). And then later if this same
address is accessed (by L1), the value of the isMarked flag would be
True. This gives some insight on how the Writeback policy of the
lower level affect the read/write accesses in an application.
Debugging is enabled by setting the verify flag to true. Debugging is
implemented using a dummy stack that behaves in a naive way, using STL
vectors. Note that this has a large impact on run time.
This patch adds the MemChecker and MemCheckerMonitor classes. While
MemChecker can be integrated anywhere in the system and is independent,
the most convenient usage is through the MemCheckerMonitor -- this
however, puts limitations on where the MemChecker is able to observe
read/write transactions.
We currently don't handle unaligned PCs correctly. There is one check
for unaligned PCs in the TLB when running in aarch64 mode, but this
check does not cover cases where the CPU does not do a TLB lookup when
decoding an instruction (e.g., a branch stays within the same cache
line). Additionally, the Decoder class sometimes throws an assertion
for unaligned PCs which breaks speculation.
This changeset introduces a decoder fault bit field in the ExtMachInst
structure. This field can be used to signal a decoder failure. If set,
the decoder generates an internal gem5fault instruction instead of a
normal instruction. This instruction in turns either panics (fault
type PANIC), returns an PCAlignmentFault (fault type UNALIGNED,
aarch64) or PrefetchAbort (fault type UNALIGNED, aarch32).
The patch causes minor changes to the realview64 regressions, and a
stats bump will follow.
This patch adds support for filtering events in the PMU. In order to
do so, it updates the ISADevice base class to forward an ISA pointer
to ISA devices. This enables such devices to access the MiscReg file
to determine the current execution level.
The aarch64 system register decoder is currently not decoding
PMXEVTYPER_EL0 and PMCCFILTR_EL0 correctly. This changeset updates the
decoder so that they are decoded using the values in table C5-6 in ARM
DDI 0478A.c.
Add an assert in the PioPort that checks if a response packet from a
device has the right flags set before passing it to them rest of the
memory system.
The new single stepping implementation for x86 doesn't rely on any ISA
specific properties or functionality. This change pulls out the per ISA
implementation of those functions and promotes the X86 implementation to the
base class.
One drawback of that implementation is that the CPU might stop on an
instruction twice if it's affected by both breakpoints and single stepping.
While that might be a little surprising, it's harmless and would only happen
under somewhat unlikely circumstances.
This stub should allow remote debugging of 32 bit and 64 bit targets. Single
stepping seems to work, as do breakpoints. If both breakpoints and single
stepping affect an instruction, gdb will stop at the instruction twice before
continuing. That's a little surprising, but is generally harmless.
