The cache's MemSidePacketQueue schedules a sendEvent based upon
nextMSHRReadyTime() which is the time when the next MSHR is ready or whenever
a future prefetch is ready. However, a prefetch being ready does not guarentee
that it can obtain an MSHR. So, when all MSHRs are full,
the simulation ends up unnecessiciarly scheduling a sendEvent every picosecond
until an MSHR is finally freed and the prefetch can happen.
This patch fixes this by not signaling the prefetch ready time if the prefetch
could not be generated. The event is rescheduled as soon as a MSHR becomes
available.
Previously the code commented about an unhandled case where it might be
possible for a writeback to arrive after a prefetch was generated but
before it was sent to the memory system. I hit that case. Luckily
the prefetchSquash() logic already in the code handles dropping prefetch
request in certian circumstances.
Re-organizes the prefetcher class structure. Previously the
BasePrefetcher forced multiple assumptions on the prefetchers that
inherited from it. This patch makes the BasePrefetcher class truly
representative of base functionality. For example, the base class no
longer enforces FIFO order. Instead, prefetchers with FIFO requests
(like the existing stride and tagged prefetchers) now inherit from a
new QueuedPrefetcher base class.
Finally, the stride-based prefetcher now assumes a custimizable lookup table
(sets/ways) rather than the previous fully associative structure.
Adds a new parameter that reserves some number of MSHR entries for demand
accesses. This helps prevent prefetchers from taking all MSHRs, forcing demand
requests from the CPU to stall.
This patch gives the user direct influence over the number of DRAM
ranks to make it easier to tune the memory density without affecting
the bandwidth (previously the only means of scaling the device count
was through the number of channels).
The patch also adds some basic sanity checks to ensure that the number
of ranks is a power of two (since we rely on bit slices in the address
decoding).
This patch addresses an issue seen with the KVM CPU where the refresh
events scheduled by the DRAM controller forces the simulator to switch
out of the KVM mode, thus killing performance.
The current patch works around the fact that we currently have no
proper API to inform a SimObject of the mode switches. Instead we rely
on drainResume being called after any switch, and cache the previous
mode locally to be able to decide on appropriate actions.
The switcheroo regression require a minor stats bump as a result.
This patch adds rank-wise refresh to the controller, as opposed to the
channel-wide refresh currently in place. In essence each rank can be
refreshed independently, and for this to be possible the controller
is extended with a state machine per rank.
Without this patch the data bus is always idle during a refresh, as
all the ranks are refreshing at the same time. With the rank-wise
refresh it is possible to use one rank while another one is
refreshing, and thus the data bus can be kept busy.
The patch introduces a Rank class to encapsulate the state per rank,
and also shifts all the relevant banks, activation tracking etc to the
rank. The arbitration is also updated to consider the state of the rank.
This patch adds a stand-alone stack distance calculator. The stack
distance calculator is a passive SimObject that observes the addresses
passed to it. It calculates stack distances (LRU Distances) of
incoming addresses based on the partial sum hierarchy tree algorithm
described by Alamasi et al. http://doi.acm.org/10.1145/773039.773043.
For each transaction a hashtable look-up is performed. At every
non-unique transaction the tree is traversed from the leaf at the
returned index to the root, the old node is deleted from the tree, and
the sums (to the right) are collected and decremented. The collected
sum represets the stack distance of the found node. At every unique
transaction the stack distance is returned as
numeric_limits<uint64>::max().
In addition to the basic stack distance calculation, a feature to mark
an old node in the tree is added. This is useful if it is required to
see the reuse pattern. For example, Writebacks to the lower level
(e.g. membus from L2), can be marked instead of being removed from the
stack (isMarked flag of Node set to True). And then later if this same
address is accessed (by L1), the value of the isMarked flag would be
True. This gives some insight on how the Writeback policy of the
lower level affect the read/write accesses in an application.
Debugging is enabled by setting the verify flag to true. Debugging is
implemented using a dummy stack that behaves in a naive way, using STL
vectors. Note that this has a large impact on run time.
This patch adds the MemChecker and MemCheckerMonitor classes. While
MemChecker can be integrated anywhere in the system and is independent,
the most convenient usage is through the MemCheckerMonitor -- this
however, puts limitations on where the MemChecker is able to observe
read/write transactions.
This patch takes a clean-slate approach to providing WriteInvalidate
(write streaming, full cache line writes without first reading)
support.
Unlike the prior attempt, which took an aggressive approach of directly
writing into the cache before handling the coherence actions, this
approach follows the existing cache flows as closely as possible.
This patch allows objects to get the src/dest of a packet even if it
is not set to a valid port id. This simplifies (ab)using the bridge as
a buffer and latency adapter in situations where the neighbouring
MemObjects are not crossbars.
The checks that were done in the packet are now shifted to the
crossbar where the fields are used to index into the port
arrays. Thus, the carrier of the information is not burdened with
checking, and the crossbar can check not only that the destination is
set, but also that the port index is within limits.
This patch attempts to make the rules for data allocation in the
packet explicit, understandable, and easy to verify. The constructor
that copies a packet is extended with an additional flag "alloc_data"
to enable the call site to explicitly say whether the newly created
packet is short-lived (a zero-time snoop), or has an unknown life-time
and therefore should allocate its own data (or copy a static pointer
in the case of static data).
The tricky case is the static data. In essence this is a
copy-avoidance scheme where the original source of the request (DMA,
CPU etc) does not ask the memory system to return data as part of the
packet, but instead provides a pointer, and then the memory system
carries this pointer around, and copies the appropriate data to the
location itself. Thus any derived packet actually never copies any
data. As the original source does not copy any data from the response
packet when arriving back at the source, we must maintain the copy of
the original pointer to not break the system. We might want to revisit
this one day and pay the price for a few extra memcpy invocations.
All in all this patch should make it easier to grok what is going on
in the memory system and how data is actually copied (or not).
This patch cleans up the use of hasData and checkFunctional in the
packet. The hasData function is unfortunately suggesting that it
checks if the packet has a valid data pointer, when it does in fact
only check if the specific packet type is specified to have a data
payload. The confusion led to a bug in checkFunctional. The latter
function is also tidied up to avoid name overloading.
This adds a basic level of sanity checking to the packet by ensuring
that a request is not modified once the packet is created. The only
issue that had to be worked around is the relaying of
software-prefetches in the cache. The specific situation is now solved
by first copying the request, and then creating a new packet
accordingly.
This patch tidies up the Request class, making all getters const. The
odd one out is incAccessDepth which is called by the memory system as
packets carry the request around. This is also const to enable the
packet to hold on to a const Request.
This patch simplifies how we deal with dynamically allocated data in
the packet, always assuming that it is array allocated, and hence
should be array deallocated (delete[] as opposed to delete). The only
uses of dataDynamic was in the Ruby testers.
The ARRAY_DATA flag in the packet is removed accordingly. No
defragmentation of the flags is done at this point, leaving a gap in
the bit masks.
As the last part the patch, it renames dataDynamicArray to dataDynamic.
This patch cleans up the packet memory allocation confusion. The data
is always allocated at the requesting side, when a packet is created
(or copied), and there is never a need for any device to allocate any
space if it is merely responding to a paket. This behaviour is in line
with how SystemC and TLM works as well, thus increasing
interoperability, and matching established conventions.
The redundant calls to Packet::allocate are removed, and the checks in
the function are tightened up to make sure data is only ever allocated
once. There are still some oddities in the packet copy constructor
where we copy the data pointer if it is static (without ownership),
and allocate new space if the data is dynamic (with ownership). The
latter is being worked on further in a follow-on patch.
This patch changes the various write functions in the port proxies
to use const pointers for all sources (similar to how memcpy works).
The one unfortunate aspect is the need for a const_cast in the packet,
to avoid having to juggle a const and a non-const data pointer. This
design decision can always be re-evaluated at a later stage.
This patch takes a first step in tightening up how we use the data
pointer in write packets. A const getter is added for the pointer
itself (getConstPtr), and a number of member functions are also made
const accordingly. In a range of places throughout the memory system
the new member is used.
The patch also removes the unused isReadWrite function.
This patch removes the parameter that enables bypassing the null check
in the Packet::getPtr method. A number of call sites assume the value
to be non-null.
The one odd case is the RubyTester, which issues zero-sized
prefetches(!), and despite being reads they had no valid data
pointer. This is now fixed, but the size oddity remains (unless anyone
object or has any good suggestions).
Finally, in the Ruby Sequencer, appropriate checks are made for flush
packets as they have no valid data pointer.
This patch adds a first cut GDDR5 config to accommodate the users
combining gem5 and GPUSim. The config is based on a SK Hynix
datasheet, and the Nvidia GTX580 specification. Someone from the
GPUSim user-camp should tweak the default page-policy and static
frontend and backend latencies.
This patch adds uncacheable/cacheable and read-only/read-write attributes to
the map method of PageTableBase. It also modifies the constructor of TlbEntry
structs for all architectures to consider the new attributes.
Ruby's functional accesses are not guaranteed to succeed as of now. While
this is not a problem for the protocols that are currently in the mainline
repo, it seems that coherence protocols for gpus rely on a backing store to
supply the correct data. The aim of this patch is to make this backing store
configurable i.e. it comes into play only when a particular option:
--access-backing-store is invoked.
The backing store has been there since M5 and GEMS were integrated. The only
difference is that earlier the system used to maintain the backing store and
ruby's copy was write-only. Sometime last year, we moved to data being
supplied supplied by ruby in SE mode simulations. And now we have patches on
the reviewboard, which remove ruby's copy of memory altogether and rely
completely on the system's memory to supply data. This patch adds back a
SimpleMemory member to RubySystem. This member is used only if the option:
access-backing-store is set to true. By default, the memory would not be
accessed.
This patch is the final in the series. The whole series and this patch in
particular were written with the aim of interfacing ruby's directory controller
with the memory controller in the classic memory system. This is being done
since ruby's memory controller has not being kept up to date with the changes
going on in DRAMs. Classic's memory controller is more up to date and
supports multiple different types of DRAM. This also brings classic and
ruby ever more close. The patch also changes ruby's memory controller to
expose the same interface.
This function was added when I had incorrectly arrived at the conclusion
that such a function can improve the chances of a functional read succeeding.
As was later realized, this is not possible in the current setup. While the
code using this function was dropped long back, this function was not. Hence
the patch.
This patch removes the data block present in the directory entry structure
of each protocol in gem5's mainline. Firstly, this is required for moving
towards common set of memory controllers for classic and ruby memory systems.
Secondly, the data block was being misused in several places. It was being
used for having free access to the physical memory instead of calling on the
memory controller.
From now on, the directory controller will not have a direct visibility into
the physical memory. The Memory Vector object now resides in the
Memory Controller class. This also means that some significant changes are
being made to the functional accesses in ruby.
In my opinion, it creates needless complications in rest of the code.
Also, this structure hinders the move towards common set of code for
physical memory controllers.
Both ruby and the system used to maintain memory copies. With the changes
carried for programmed io accesses, only one single memory is required for
fs simulations. This patch sets the copy of memory that used to reside
with the system to null, so that no space is allocated, but address checks
can still be carried out. All the memory accesses now source and sink values
to the memory maintained by ruby.
As of now DMASequencer inherits from the RubyPort class. But the code in
RubyPort class is heavily tailored for the CPU Sequencer. There are parts of
the code that are not required at all for the DMA sequencer. Moreover, the
next patch uses the dma sequencer for carrying out memory accesses for all the
io devices. Hence, it is better to have a leaner dma sequencer.
WriteInvalidate semantics depend on the unconditional writeback
or they won't complete. Also, there's no point in deferring snoops
on their MSHRs, as they don't get new data at the end of their life
cycle the way other transactions do.
Add comment in the cache about a minor inefficiency re: WriteInvalidate.
Since WriteInvalidate directly writes into the cache, it can
create tricky timing interleavings with reads and writes to the
same cache line that haven't yet completed. This patch ensures
that these requests, when completed, don't overwrite the newer
data from the WriteInvalidate.
This patch adds the size of the DRAM device to the DRAM config. It
also compares the actual DRAM size (calculated using information from
the config) to the size defined in the system. If these two values do
not match gem5 will print a warning. In order to do correct DRAM
research the size of the memory defined in the system should match the
size of the DRAM in the config. The timing and current parameters
found in the DRAM configs are defined for a DRAM device with a
specific size and would differ for another device with a different
size.
This patch adds two MemoryObject's: ExternalMaster and ExternalSlave.
Each object has a single port which can be bound to an externally-
provided bridge to a port of another simulation system at
initialisation.
This patch transitions the Ruby Message and its derived classes from
the ad-hoc RefCountingPtr to the c++11 shared_ptr. There are no
changes in behaviour, and the code modifications are mainly replacing
"new" with "make_shared".
The cloning of derived messages is slightly changed as they previously
relied on overriding the base-class through covariant return types.
This patch makes the memory system ISA-agnostic by enabling the Ruby
Sequencer to dynamically determine if it has to do a store check. To
enable this check, the ISA is encoded as an enum, and the system
is able to provide the ISA to the Sequencer at run time.
--HG--
rename : src/arch/x86/insts/microldstop.hh => src/arch/x86/ldstflags.hh
This patch takes a step towards an ISA-agnostic memory
system by enabling the components to establish the page size after
instantiation. The swap operation in the memory is now also allowing
any granularity to avoid depending on the IntReg of the ISA.
This patch adds some statistics to garnet that record the activity
of certain structures in the on-chip network. These statistics, in a later
patch, will be used for computing the energy consumed by the on-chip network.
Orion is being dropped from ruby. It would be replaced with DSENT
which has better models. Note that the power / energy numbers reported
after this patch has been applied are not for use.
This patch takes the final step in integrating DRAMPower and adds the
appropriate calls in the DRAM controller to provide the command trace
and extract the power and energy stats. The debug printouts are still
left in place, but will eventually be removed.
At the moment the DRAM power calculation is always on when using the
DRAM controller model. The run-time impact of this addition is around
1.5% when looking at the total host seconds of the regressions. We
deem this a sensible trade-off to avoid the complication of adding an
enable/disable mechanism.
This patch adds a class to wrap DRAMPower Library in gem5.
This class initiates an object of class MemorySpecification
of the DRAMPower Library, passes the parameters from DRAMCtrl.py
to this object and creates an object of drampower library using
the memory specification.
This patch adds missing timing and current parameters to the existing
DRAM configs. These missing timing and current parameters are required
by DRAMPower for the DRAM power calculations. The missing values are
datasheet values of the specified DRAMs, and the appropriate
references are added for the variuos configs.
This patch prunes the DDR3 config that was initially created to match
the default config of DRAMSim2. The config is not complete as it is,
and to avoid having to maintain it, the easiest way forward is to
simply prune it. Going forward we are adding power number etc to the
other configurations.
This patch changes the name of the Bus classes to XBar to better
reflect the actual timing behaviour. The actual instances in the
config scripts are not renamed, and remain as e.g. iobus or membus.
As part of this renaming, the code has also been clean up slightly,
making use of range-based for loops and tidying up some comments. The
only changes outside the bus/crossbar code is due to the delay
variables in the packet.
--HG--
rename : src/mem/Bus.py => src/mem/XBar.py
rename : src/mem/coherent_bus.cc => src/mem/coherent_xbar.cc
rename : src/mem/coherent_bus.hh => src/mem/coherent_xbar.hh
rename : src/mem/noncoherent_bus.cc => src/mem/noncoherent_xbar.cc
rename : src/mem/noncoherent_bus.hh => src/mem/noncoherent_xbar.hh
rename : src/mem/bus.cc => src/mem/xbar.cc
rename : src/mem/bus.hh => src/mem/xbar.hh
Adds a simple access counter for requests and snoops for the snoop filter and
also classifies hits based on whether a single other holder existed or whether
multiple shares held the line.
This patch adds a simple counter for both total messages and a histogram for
the fan-out of snoop messages. The fan-out describes to how many ports snoops
had to be sent per incoming request / snoop-from-below. Without any
cleverness, this usually means to either all, or all but the requesting port.
This is a first cut at a simple snoop filter that tracks presence of lines in
the caches "above" it. The snoop filter can be applied at any given cache
hierarchy and will then handle the caches above it appropriately; there is no
need to use this only in the last-level bus.
This design currently has some limitations: missing stats, no notion of clean
evictions (these will not update the underlying snoop filter, because they are
not sent from the evicting cache down), no notion of capacity for the snoop
filter and thus no need for invalidations caused by capacity pressure in the
snoop filter. These are planned to be added on top with future change sets.
Added the following parameter to the DRAMCtrl class:
- bank_groups_per_rank
This defaults to 1. For the DDR4 case, the default is overridden to indicate
bank group architecture, with multiple bank groups per rank.
Added the following delays to the DRAMCtrl class:
- tCCD_L : CAS-to-CAS, same bank group delay
- tRRD_L : RAS-to-RAS, same bank group delay
These parameters are only applied when bank group timing is enabled. Bank
group timing is currently enabled only for DDR4 memories.
For all other memories, these delays will default to '0 ns'
In the DRAM controller model, applied the bank group timing to the per bank
parameters actAllowedAt and colAllowedAt.
The actAllowedAt will be updated based on bank group when an ACT is issued.
The colAllowedAt will be updated based on bank group when a RD/WR burst is
issued.
At the moment no modifications are made to the scheduling.
Add the following delay to the DRAM controller:
- tCS : Different rank bus turnaround delay
This will be applied for
1) read-to-read,
2) write-to-write,
3) write-to-read, and
4) read-to-write
command sequences, where the new command accesses a different rank
than the previous burst.
The delay defaults to 2*tCK for each defined memory class. Note that
this does not correspond to one particular timing constraint, but is a
way of modelling all the associated constraints.
The DRAM controller has some minor changes to prioritize commands to
the same rank. This prioritization will only occur when the command
stream is not switching from a read to write or vice versa (in the
case of switching we have a gap in any case).
To prioritize commands to the same rank, the model will determine if there are
any commands queued (same type) to the same rank as the previous command.
This check will ensure that the 'same rank' command will be able to execute
without adding bubbles to the command flow, e.g. any ACT delay requirements
can be done under the hoods, allowing the burst to issue seamlessly.
There are two primary issues with this code which make it deserving of deletion.
1) GHB is a way to structure a prefetcher, not a definitive type of prefetcher
2) This prefetcher isn't even structured like a GHB prefetcher.
It's basically a worse version of the stride prefetcher.
It primarily serves to confuse new gem5 users and most functionality is already
present in the stride prefetcher.
The changeset ad9c042dce54 made changes to the structures under the network
directory to use a map of buffers instead of vector of buffers.
The reasoning was that not all vnets that are created are used and we
needlessly allocate more buffers than required and then iterate over them
while processing network messages. But the move to map resulted in a slow
down which was pointed out by Andreas Hansson. This patch moves things
back to using vector of message buffers.
Static analysis unearther a bunch of uninitialised variables and
members, and this patch addresses the problem. In all cases these
omissions seem benign in the end, but at least fixing them means less
false positives next time round.
This patch tidies up random number generation to ensure that it is
done consistently throughout the code base. In essence this involves a
clean-up of Ruby, and some code simplifications in the traffic
generator.
As part of this patch a bunch of skewed distributions (off-by-one etc)
have been fixed.
Note that a single global random number generator is used, and that
the object instantiation order will impact the behaviour (the sequence
of numbers will be unaffected, but if module A calles random before
module B then they would obviously see a different outcome). The
dependency on the instantiation order is true in any case due to the
execution-model of gem5, so we leave it as is. Also note that the
global ranom generator is not thread safe at this point.
Regressions using the memtest, TrafficGen or any Ruby tester are
affected and will be updated accordingly.
This patch removes unecessary retries that happened when the bus layer
itself was no longer busy, but the the peer was not yet ready. Instead
of sending a retry that will inevitably not succeed, the bus now
silenty waits until the peer sends a retry.
Support full-block writes directly rather than requiring RMW:
* a cache line is allocated in the cache upon receipt of a
WriteInvalidateReq, not the WriteInvalidateResp.
* only top-level caches allocate the line; the others just pass
the request along and invalidate as necessary.
* to close a timing window between the *Req and the *Resp, a new
metadata bit tracks whether another cache has read a copy of
the new line before the writeback to memory.
This patch fixes a bug in the cache port where the retry flag was
reset too early, allowing new requests to arrive before the retry was
actually sent, but with the event already scheduled. This caused a
deadlock in the interactions with the O3 LSQ.
The patche fixes the underlying issue by shifting the resetting of the
flag to be done by the event that also calls sendRetry(). The patch
also tidies up the flow control in recvTimingReq and ensures that we
also check if we already have a retry outstanding.
Previously, they were treated so much like loads that they could stall
at the head of the ROB. Now they are always treated like L1 hits.
If they actually miss, a new request is created at the L1 and tracked
from the MSHRs there if necessary (i.e. if it didn't coalesce with
an existing outstanding load).
If a set of LL/SC requests contend on the same cache block we
can get into a situation where CPUs will deadlock if they expect
a failed SC to supply them data. This case happens where 3 or
more cores are contending for a cache block using LL/SC and the system
is configured where 2 cores are connected to a local bus and the
third is connected to a remote bus. If a core on the local bus
sends an SCUpgrade and the core on the remote bus sends and SCUpgrade
they will race to see who will win the SC access. In the meantime
if the other core appends a read to one of the SCUpgrades it will expect
to be supplied data by that SCUpgrade transaction. If it happens that
the SCUpgrade that was picked to supply the data is failed, it will
drop the appended request for data and never respond, leaving the requesting
core to deadlock. This patch makes all SC's behave as normal stores to
prevent this case but still makes sure to check whether it can perform
the update.
This patch prunes unused values, and also unifies how the values are
defined (not using an enum for ALPHA), aligning the use of int vs Addr
etc.
The patch also removes the duplication of PageBytes/PageShift and
VMPageSize/LogVMPageSize. For all ISAs the two pairs had identical
values and the latter has been removed.
The Index type defined as typedef int64 does not really provide any help
since in most places we use primitive types instead of Index. Also, the name
Index is very generic that it does not merit being used as a typename.
This patch is the final patch in a series of patches. The aim of the series
is to make ruby more configurable than it was. More specifically, the
connections between controllers are not at all possible (unless one is ready
to make significant changes to the coherence protocol). Moreover the buffers
themselves are magically connected to the network inside the slicc code.
These connections are not part of the configuration file.
This patch makes changes so that these connections will now be made in the
python configuration files associated with the protocols. This requires
each state machine to expose the message buffers it uses for input and output.
So, the patch makes these buffers configurable members of the machines.
The patch drops the slicc code that usd to connect these buffers to the
network. Now these buffers are exposed to the python configuration system
as Master and Slave ports. In the configuration files, any master port
can be connected any slave port. The file pyobject.cc has been modified to
take care of allocating the actual message buffer. This is inline with how
other port connections work.
A later changeset changes the file src/python/swig/pyobject.cc to include
a header file that includes a header file generated at build time depending
on the PROTOCOL in use. Since NULL ISA was not specifying any protocol,
this resulted in compilation problems. Hence, the changeset.
The namespace Message conflicts with the Message data type used extensively
in Ruby. Since Ruby is being moved to the same Master/Slave ports based
configuration style as the rest of gem5, this conflict needs to be resolved.
Hence, the namespace is being renamed to ProtoMessage.
There are two changes this patch makes to the way configurable members of a
state machine are specified in SLICC. The first change is that the data
member declarations will need to be separated by a semi-colon instead of a
comma. Secondly, the default value to be assigned would now use SLICC's
assignment operator i.e. ':='.
This patch changes the grammar for SLICC so as to remove some of the
redundant / duplicate rules. In particular rules for object/variable
declaration and class member declaration have been unified. Similarly, the
rules for a general function and a class method have been unified.
One more change is in the priority of two rules. The first rule is on
declaring a function with all the params typed and named. The second rule is
on declaring a function with all the params only typed. Earlier the second
rule had a higher priority. Now the first rule has a higher priority.
This patch enables the use of page tables that are stored in system memory
and respect x86 specification, in SE mode. It defines an architectural
page table for x86 as a MultiLevelPageTable class and puts a placeholder
class for other ISAs page tables, giving the possibility for future
implementation.
This patch defines a multi-level page table class that stores the page table in
system memory, consistent with ISA specifications. In this way, cpu models that
use the actual hardware to execute (e.g. KvmCPU), are able to traverse the page
table.
This patch ensures the cycle check is still valid even restoring from
a checkpoint. In this case the DRAMSim2 cycle count is relative to the
startTick rather than 0.
This patch fixes a bug in the DRAM controller address decoding. In
cases where the DRAM burst size (e.g. 32 bytes in a rank with a single
LPDDR3 x32) was smaller than the channel interleaving size
(e.g. systems with a 64-byte cache line) one address bit effectively
got used as a channel bit when it should have been a low-order column
bit.
This patch adds a notion of "columns per stripe", and more clearly
deals with the low-order column bits and high-order column bits. The
patch also relaxes the granularity check such that it is possible to
use interleaving granularities other than the cache line size.
The patch also adds a missing M5_CLASS_VAR_USED to the tCK member as
it is only used in the debug build for now.
When a cacheline is written back to a lower-level cache,
tags->insertBlock() sets various status parameters. However these
status bits were cleared immediately after calling. This patch makes
it so that these status fields are not cleared by moving them outside
of the tags->insertBlock() call.
this patch implements a new tags class that uses a random replacement policy.
these tags prefer to evict invalid blocks first, if none are available a
replacement candidate is chosen at random.
this patch factors out the common code in the LRU class and creates a new
abstract class: the BaseSetAssoc class. any set associative tag class must
implement the functionality related to the actual replacement policy in the
following methods:
accessBlock()
findVictim()
insertBlock()
invalidate()
This patch adds a DRAMPower flag to enable off-line DRAM power
analysis using the DRAMPower tool. A new DRAMPower flag is added
and a follow-on patch adds a Python script to post-process the output
and order it based on time stamps.
The long-term goal is to link DRAMPower as a library and provide the
commands through function calls to the model rather than first
printing and then parsing the commands. At the moment it is also up to
the user to ensure that the same DRAM configuration is used by the
gem5 controller model and DRAMPower.
This patch adds the index of the bank and rank as a field so that we can
determine the identity of a given bank (reference or pointer) for the
power tracing. We also grab the opportunity of cleaning up the
arguments used for identifying the bank when activating.
Using '== true' in a boolean expression is totally redundant,
and using '== false' is pretty verbose (and arguably less
readable in most cases) compared to '!'.
It's somewhat of a pet peeve, perhaps, but I had some time
waiting for some tests to run and decided to clean these up.
Unfortunately, SLICC appears not to have the '!' operator,
so I had to leave the '== false' tests in the SLICC code.
This patch makes a more firm connection between the DDR3-1600
configuration and the corresponding datasheet, and also adds a
DDR3-2133 and a DDR4-2400 configuration. At the moment there is also
an ongoing effort to align the choice of datasheets to what is
available in DRAMPower.
This patch extends the current timing parameters with the DRAM cycle
time. This is needed as the DRAMPower tool expects timestamps in DRAM
cycles. At the moment we could get away with doing this in a
post-processing step as the DRAMPower execution is separate from the
simulation run. However, in the long run we want the tool to be called
during the simulation, and then the cycle time is needed.
This patch adds the basic ingredients for a precharge all operation,
to be used in conjunction with DRAM power modelling.
Currently we do not try and apply any cleverness when precharging all
banks, thus even if only a single bank is open we use PREA as opposed
to PRE. At the moment we only have a single tRP (tRPpb), and do not
model the slightly longer all-bank precharge constraint (tRPab).
This patch adds the tRTP timing constraint, governing the minimum time
between a read command and a precharge. Default values are provided
for the existing DRAM types.
This patch merges the two control paths used to estimate the latency
and update the bank state. As a result of this merging the computation
is now in one place only, and should be easier to follow as it is all
done in absolute (rather than relative) time.
As part of this change, the scheduling is also refined to ensure that
we look at a sensible estimate of the bank ready time in choosing the
next request. The bank latency stat is removed as it ends up being
misleading when the DRAM access code gets evaluated ahead of time (due
to the eagerness of waking the model up for scheduling the next
request).
This patch adds the write recovery time to the DRAM timing
constraints, and changes the current tRASDoneAt to a more generic
preAllowedAt, capturing when a precharge is allowed to take place.
The part of the DRAM access code that accounts for the precharge and
activate constraints is updated accordingly.
This patch adds power states to the controller. These states and the
transitions can be used together with the Micron power model. As a
more elaborate use-case, the transitions can be used to drive the
DRAMPower tool.
At the moment, the power-down modes are not used, and this patch
simply serves to capture the idle, auto refresh and active modes. The
patch adds a third state machine that interacts with the refresh state
machine.
This patch adds a state machine for the refresh scheduling to
ensure that no accesses are allowed while the refresh is in progress,
and that all banks are propely precharged.
As part of this change, the precharging of banks of broken out into a
method of its own, making is similar to how activations are dealt
with. The idle accounting is also updated to ensure that the refresh
duration is not added to the time that the DRAM is in the idle state
with all banks precharged.
This patch changes the read/write event loop to use a single event
(nextReqEvent), along with a state variable, thus joining the two
control flows. This change makes it easier to follow the state
transitions, and control what happens when.
With the new loop we modify the overly conservative switching times
such that the write-to-read switch allows bank preparation to happen
in parallel with the bus turn around. Similarly, the read-to-write
switch uses the introduced tRTW constraint.
This patch squashes prefetch requests from downstream caches,
so that they do not steal cachelines away from caches closer
to the cpu. It was originally coded by Mitch Hayenga and
modified by Aasheesh Kolli.
Splits the CommMonitor trace_file parameter into three parameters. Previously,
the trace was only enabled if the trace_file parameter was set, and would be
written to this file. This patch adds in a trace_enable and trace_compress
parameter to the CommMonitor.
No trace is generated if trace_enable is set to False. If it is set to True, the
trace is written to a file based on the name of the SimObject in the simulation
hierarchy. For example, system.cluster.il1_commmonitor.trc. This filename can be
overridden by additionally specifying a file name to the trace_file parameter
(more on this later).
The trace_compress parameter will append .gz to any filename if set to True.
This enables compression of the generated traces. If the file name already ends
in .gz, then no changes are made.
The trace_file parameter will override the name set by the trace_enable
parameter. In the case that the specified name does not end in .gz but
trace_compress is set to true, .gz is appended to the supplied file name.
This never actually worked since it was printing out only a word
of the cache block and not the entire thing and doubly didn't work
csprintf overrides the %#x specifier and assumes a char* array is
actually a string.
Upon aggregating records, serialize system's cache-block size, as the
cache-block size can be different when restoring from a checkpoint. This way,
we can correctly read all records when restoring from a checkpoints, even if
the cache-block size is different.
Note, that it is only possible to restore from a checkpoint if the
desired cache-block size is smaller or equal to the cache-block size
when the checkpoint was taken; we can split one larger request into
multiple small ones, but it is not reliable to do the opposite.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
As of now, the enqueue statement can take in any number of 'pairs' as
argument. But we only use the pair in which latency is the key. This
latency is allowed to be either a fixed integer or a member variable of
controller in which the expression appears. This patch drops the use of pairs
in an enqueue statement. Instead, an expression is allowed which will be
interpreted to be the latency of the enqueue. This expression can anything
allowed by slicc including a constant integer or a member variable.
This patch adds stats for tracking the number of reads/writes per bus
turn around, and also adds hysteresis to the write-to-read switching
to ensure that the queue does not oscilate around the low threshold.
This patch renames the not-so-simple SimpleDRAM to a more suitable
DRAMCtrl. The name change is intended to ensure that we do not send
the wrong message (although the "simple" in SimpleDRAM was originally
intended as in cleverly simple, or elegant).
As the DRAM controller modelling work is being presented at ISPASS'14
our hope is that a broader audience will use the model in the future.
--HG--
rename : src/mem/SimpleDRAM.py => src/mem/DRAMCtrl.py
rename : src/mem/simple_dram.cc => src/mem/dram_ctrl.cc
rename : src/mem/simple_dram.hh => src/mem/dram_ctrl.hh
Make the default memory type DDR3-1600 x64, and use the open-adaptive
page policy. This change is aiming to ensure that users by default are
using a realistic memory system.
This patch adds a basic starvation-prevention mechanism where a DRAM
page is forced to close after a certain number of accesses. The limit
is combined with the open and open-adaptive page policy and if reached
causes an auto-precharge.
This patch changes the triggering condition for the write draining
such that we grab the opportunity to issue writes if there are no
reads waiting (as opposed to waiting for the writes to reach the high
threshold). As a result, we potentially drain some of the writes in read
idle periods (if any).
A low threshold is added to be able to control how many write bursts
are kept in the memory controller queue (acting as on-chip storage).
The high and low thresholds are updated to sensible values for a 32/64
size write buffer. Note that the thresholds should be adjusted along
with the queue sizes.
This patch also adds some basic initialisation sanity checks and moves
part of the initialisation to the constructor.
This patch adds the row bits to the name of the address mapping
schemes to make it more clear that all the current schemes places the
row bits as the most significant bits.
This patch moves the Ruby-related debug flags to the ruby
sub-directory, and also removes the state SConsopts that add the
no-longer-used NO_VECTOR_BOUNDS_CHECK.
Each consumer object maintains a set of tick values when the object is supposed
to wakeup and do some processing. As of now, the object accesses this set both
when scheduling a wakeup event and when the object actually wakes up. The set
is accessed during wakeup to remove the current tick value from the set. This
functionality is now being moved to the scheduling function where ticks are
removed at a later time.
This helps in configuring the network interfaces from the python script and
these objects no longer rely on the network object for the timing information.
Piobus was recently added to se scripts for ruby so that the interrupt
controller can be connected to something (required since the interrupt
controller sends address range messages). This patch removes the piobus
and instead, the pio port of ruby port will now ignore the range change
messages in se mode.
This patch fixes an assert condition that is not true at all
times. There are valid situations that arise in dual-core
dual-workload runs where the assert condition is false. The function
call following the assert however needs to be called only when the
condition is true (a block cannot be invalidated in the tags structure
if has not been allocated in the structure, and the tempBlock is never
allocated). Hence the 'assert' has been replaced with an 'if'.
Couple of users observed segmentation fault when the simulator tries to
register the statistical variable m_IncompleteTimes. It seems that there
is some problem with the initialization of these variables when allocated
in the constructor.
Currently, the interrupt controller in x86 is connected to the io bus
directly. Therefore the packets between the io devices and the interrupt
controller do not go through ruby. This patch changes ruby port so that
these packets arrive at the ruby port first, which then routes them to their
destination. Note that the patch does not make these packets go through the
ruby network. That would happen in a subsequent patch.
This patch simplfies the retry logic in the RubyPort, avoiding
redundant attributes, and enforcing more stringent checks on the
interactions with the normal ports. The patch also simplifies the
routing done by the RubyPort, using the port identifiers instead of a
heavy-weight sender state.
The patch also fixes a bug in the sending of responses from PIO
ports. Previously these responses bypassed the queue in the queued
port, and ignored the return value, potentially leading to response
packets being lost.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Code in two of the functions was exactly the same. This patch moves
this code to a new function which is called from the two functions
mentioned initially.
At several places, there are functions that take a cycle value as input
and performs some computation. Along with each such function, another
function was being defined that simply added one more cycle to input and
computed the same function. This patch removes this second copy of the
function. Places where these functions were being called have been updated
to use the original function with argument being current cycle + 1.
Two files had been incorrectly named with a .cache suffix.
--HG--
rename : src/mem/protocol/MESI_Three_Level-L0.cache => src/mem/protocol/MESI_Three_Level-L0cache.sm
rename : src/mem/protocol/MESI_Three_Level-L1.cache => src/mem/protocol/MESI_Three_Level-L1cache.sm
This patch fixes a bug in how physical memory used to be mapped and
unmapped. Previously we unmapped and re-mapped if restoring from a
checkpoint. However, we never checked that the new mapping was
actually the same, it was just magically working as the OS seems to
fairly reliably give us the same chunk back. This patch fixes this
issue by relying entirely on the mmap call in the constructor.
This patch adds a filter to the cache to drop snoop requests that are
not for a range covered by the cache. This fixes an issue observed
when multiple caches are placed in parallel, covering different
address ranges. Without this patch, all the caches will forward the
snoop upwards, when only one should do so.
This patch adds DRAMSim2 as a memory controller by wrapping the
external library and creating a sublass of AbstractMemory that bridges
between the semantics of gem5 and the DRAMSim2 interface.
The DRAMSim2 wrapper extracts the clock period from the config
file. There is no way of extracting this information from DRAMSim2
itself, so we simply read the same config file and get it from there.
To properly model the response queue, the wrapper keeps track of how
many transactions are in the actual controller, and how many are
stacking up waiting to be sent back as responses (in the wrapper). The
latter requires us to move away from the queued port and manage the
packets ourselves. This is due to DRAMSim2 not having any flow control
on the response path.
DRAMSim2 assumes that the transactions it is given are matching the
burst size of the choosen memory. The wrapper checks to ensure the
cache line size of the system matches the burst size of DRAMSim2 as
there are currently no provisions to split the system requests. In
theory we could allow a cache line size smaller than the burst size,
but that would lead to inefficient use of the DRAM, so for not we
fatal also in this case.
Forces the prefetcher to mispredict twice in a row before resetting the
confidence of prefetching. This helps cases where a load PC strides by a
constant factor, however it may operate on different arrays at times.
Avoids the cost of retraining. Primarily helps with small iteration loops.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
For systems with a tightly coupled L2, a stride-based prefetcher may observe
access requests from both instruction and data L1 caches. However, the PC
address of an instruction miss gives no relevant training information to the
stride based prefetcher(there is no stride to train). In theses cases, its
better if the L2 stride prefetcher simply reverted back to a simple N-block
ahead prefetcher. This patch enables this option.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch extends the classic prefetcher to work on non-block aligned
addresses. Because the existing prefetchers in gem5 mask off the lower
address bits of cache accesses, many predictable strides fail to be
detected. For example, if a load were to stride by 48 bytes, with 64 byte
cachelines, the current stride based prefetcher would see an access pattern
of 0, 64, 64, 128, 192.... Thus not detecting a constant stride pattern. This
patch fixes this, by training the prefetcher on access and not masking off the
lower address bits.
It also adds the following configuration options:
1) Training/prefetching only on cache misses,
2) Training/prefetching only on data acceses,
3) Optionally tagging prefetches with a PC address.
#3 allows prefetchers to train off of prefetch requests in systems with
multiple cache levels and PC-based prefetchers present at multiple levels.
It also effectively allows a pipelining of prefetch requests (like in POWER4)
across multiple levels of cache hierarchy.
Improves performance on my gem5 configuration by 4.3% for SPECINT and 4.7% for SPECFP (geomean).
The patch
(1) removes the redundant writeback argument from findVictim()
(2) fixes the description of access() function
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Adds very basic statistics on the number of tag and data accesses within the
cache, which is important for power modelling. For the tags, simply count
the associativity of the cache each time. For the data, this depends on
whether tags and data are accessed sequentially, which is given by a new
parameter. In the parallel case, all data blocks are accessed each time, but
with sequential accesses, a single data block is accessed only on a hit.
This patch enables tracking of cache occupancy per thread along with
ages (in buckets) per cache blocks. Cache occupancy stats are
recalculated on each stat dump.
Add some values and methods to the request object to track the translation
and access latency for a request and which level of the cache hierarchy responded
to the request.
The first two levels (L0, L1) are private to the core, the third level (L2)is
possibly shared. The protocol supports clustered designs. For example, one
can have two sets of two cores. Each core has an L0 and L1 cache. There are
two L2 controllers where each set accesses only one of the L2 controllers.
A cluster over here means a set of controllers that can be accessed only by a
certain set of cores. For example, consider a two level hierarchy. Assume
there are 4 L1 controllers (private) and 2 L2 controllers. We can have two
different hierarchies here:
a. the address space is partitioned between the two L2 controllers. Each L1
controller accesses both the L2 controllers. In this case, each L1 controller
is a cluster initself.
b. both the L2 controllers can cache any address. An L1 controller has access
to only one of the L2 controllers. In this case, each L2 controller
along with the L1 controllers that access it, form a cluster.
This patch allows for each controller to have a cluster ID, which is 0 by
default. By setting the cluster ID properly, one can instantiate hierarchies
with clusters. Note that the coherence protocol might have to be changed as
well.
This patch fixes couple of bugs in the L2 controller of the mesi cmp
directory protocol.
1. The state MT_I was transitioning to NP on receiving a clean writeback
from the L1 controller. This patch makes it inform the directory controller
about the writeback.
2. The L2 controller was sending the dirty bit to the L1 controller and the
L2 controller used writeback from the L1 controller to update the dirty bit
unconditionally. Now, the L1 controller always assumes that the incoming
data is clean. The L2 controller updates the dirty bit only when the L1
controller writes to the block.
3. Certain unused functions and events are being removed.
This patch replaces max_in_port_rank with the number of inports. The use of
max_in_port_rank was causing spurious re-builds and incorrect initialization
of variables in ruby related regression tests. This was due to the variable
value being used across threads while compiling when it was not meant to be.
Since the number of inports is state machine specific value, this problem
should get solved.
The directory controller should not have the sharer field since there is
only one level 2 cache. Anyway the field was not in use. The owner field
was being used to track the l2 cache version (in case of distributed l2) that
has the cache block under consideration. The information is not required
since the version of the level 2 cache can be obtained from a subset of the
address bits.
This patch fixes a number of stats accounting issues in the DRAM
controller. Most importantly, it separates the system interface and
DRAM interface so that it is clearer what the actual DRAM bandwidth
(and consequently utilisation) is.
This patch unifies the request selection across read and write queues
for FR-FCFS scheduling policy. It also fixes the request selection
code to prioritize the row hits present in the request queues over the
selection based on earliest bank availability.
This patch adds a basic adaptive version of the open-page policy that
guides the decision to keep open or close by looking at the contents
of the controller queues. If no row hits are found, and bank conflicts
are present, then the row is closed by means of an auto
precharge. This is a well-known technique that should improve
performance in most use-cases.
This patch removes the untimed while loop in the write scheduling
mechanism and now schedule commands taking into account the minimum
timing constraint. It also introduces an optimization to track write
queue size and switch from writes to reads if the number of write
requests fall below write low threshold.
This patch adds the tRRD parameter to the DRAM controller. With the
recent addition of the actAllowedAt member for each bank, this
addition is trivial.
This patch changes the tXAW constraint so that it is enforced per rank
rather than globally for all ranks in the channel. It also avoids
using the bank freeAt to enforce the activation limit, as doing so
also precludes performing any column or row command to the
DRAM. Instead the patch introduces a new variable actAllowedAt for the
banks and use this to track when a potential activation can occur.
This patch fixes the controller when a write threshold of 100% is
used. Earlier for 100% write threshold no data is written to memory
as writes never get triggered since this corner case is not
considered.
This patch changes the FCFS bit of FR-FCFS such that requests that
target the earliest available bank are picked first (as suggested in
the original work on FR-FCFS by Rixner et al). To accommodate this we
add functionality to identify a bank through a one-dimensional
identifier (bank id). The member names of the DRAMPacket are also
update to match the style guide.
This patch changes the time the controller is woken up to take the
next scheduling decisions. tRAS is now handled in estimateLatency and
doDRAMAccess and we do not need to worry about it at scheduling
time. The earliest we need to wake up is to do a pre-charge, row
access and column access before the bus becomes free for use.
This patch adds an explicit tRAS parameter to the DRAM controller
model. Previously tRAS was, rather conservatively, assumed to be tRCD
+ tCL + tRP. The default values for tRAS are chosen to match the
previous behaviour and will be updated later.
This patch adds missing initializations of the SenderMachine field of
out_msg's when thery are created in the L2 cache controller of the
MOESI_CMP_directory coherence protocol. When an out_msg is created and this
field is left uninitialized, it is set to the default value MachineType_NUM.
This causes a panic in the MachineType_to_string function when gem5 is
executed with the Ruby debug flag on and it tries to print the message.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch fixes a problem where in Garnet, the enqueue time in the
VCallocator and the SWallocator which is of type Cycles was being stored
inside a variable with int type.
This lead to a known problem restoring checkpoints with garnet & the fixed
pipeline enabled. That value was really big and didn't fit in the variable
overflowing it, therefore some conditions on the VC allocation stage & the
SW allocation stage were not met and the packets didn't advance through the
network, leading to a deadlock panic right after the checkpoint was restored.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
The CoherentBus eventually got virtual methods for its interface. The
"virtuality" of the CoherentBus, however, comes already from the virtual
interface of the bus' ports. There is no need to add another layer of virtual
functions, here.
Get rid of non-deterministic "stats" in ruby.stats output
such as time & date of run, elapsed & CPU time used,
and memory usage. These values cause spurious
miscomparisons when looking at output diffs (though
they don't affect regressions, since the regressions
pass/fail status currently ignores ruby.stats entirely).
Most of this information is already captured in other
places (time & date in stdout, elapsed time & mem usage
in stats.txt), where the regression script is smart
enough to filter it out. It seems easier to get rid of
the redundant output rather than teaching the
regression tester to ignore the same information in
two different places.
ASI_BITS in the Request object were originally used to store a memory
request's ASI on SPARC. This is not the case any more since other ISAs
use the ASI bits to store architecture-dependent information. This
changeset renames the ASI_BITS to ARCH_BITS which better describes
their use. Additionally, the getAsi() accessor is renamed to
getArchFlags().
Using address bit 63 to identify generic IPRs caused problems on
SPARC, where IPRs are heavily used. This changeset redefines how
generic IPRs are identified. Instead of using bit 63, we now use a
separate flag (GENERIC_IPR) a memory request.
This patch ensures that a dequeue event is not scheduled if the memory
controller is waiting for a retry already. Without this check it is
possible for the controller to attempt sending something whilst
already having one packet that is in retry, thus causing the bus to
have an assertion failure.
The Topology source sets up input and output buffers for each of the external
nodes of a topology by indexing on Ruby's generated controller unique IDs.
These unique IDs are found by adding the MachineType_base_number to the version
number of each controller (see any generated *_Controller.cc - init() calls
getToNetQueue and getFromNetQueue using m_version + base). However, the
Topology object used the cntrl_id - which is required to be unique across all
controllers - to index the controllers list as they are being connected to
their input and output buffers. If the cntrl_ids did not match the Ruby unique
ID, the throttles end up connected to incorrectly indexed nodes in the network,
resulting in packets traversing incorrect network paths. This patch fixes the
Topology indexing scheme by using the Ruby unique ID to match that of the
SimpleNetwork buffer vectors.
The previous changeset (9863:9483739f83ee) used STL vector containers to
dynamically allocate stats in the Ruby SimpleNetwork, Switch and Throttle. For
gcc versions before at least 4.6.3, this causes the standard vector allocator
to call Stats copy constructors (a no-no, since stats should be allocated in
the body of each SimObject instance). Since the size of these stats arrays is
known at compile time (NOTE: after code generation), this patch changes their
allocation to be static rather than using an STL vector.
This patch makes it possible to once again build gem5 without any
ISA. The main purpose is to enable work around the interconnect and
memory system without having to build any CPU models or device models.
The regress script is updated to include the NULL ISA target. Currently
no regressions make use of it, but all the testers could (and perhaps
should) transition to it.
--HG--
rename : build_opts/NOISA => build_opts/NULL
rename : src/arch/noisa/SConsopts => src/arch/null/SConsopts
rename : src/arch/noisa/cpu_dummy.hh => src/arch/null/cpu_dummy.hh
rename : src/cpu/intr_control.cc => src/cpu/intr_control_noisa.cc
This patch updates the stats to reflect the: 1) addition of the
internal queue in SimpleMemory, 2) moving of the memory class outside
FSConfig, 3) fixing up of the 2D vector printing format, 4) specifying
burst size and interface width for the DRAM instead of relying on
cache-line size, 5) performing merging in the DRAM controller write
buffer, and 6) fixing how idle cycles are counted in the atomic and
timing CPU models.
The main reason for bundling them up is to minimise the changeset
size.
This patch adds support for specifying multi-channel memory
configurations on the command line, e.g. 'se/fs.py
--mem-type=ddr3_1600_x64 --mem-channels=4'. To enable this, it
enhances the functionality of MemConfig and moves the existing
makeMultiChannel class method from SimpleDRAM to the support scripts.
The se/fs.py example scripts are updated to make use of the new
feature.
This patch changes the default parameter value of conf_table_reported
to match the common case. It also simplifies the regression and config
scripts to reflect this change.
This patch changes the data structure used for the DRAM read, write
and response queues from an STL list to deque. This optimisation is
based on the observation that the size is small (and fixed), and that
the structures are frequently iterated over in a linear fashion.
This patch implements basic write merging in the DRAM to avoid
redundant bursts. When a new access is added to the queue it is
compared against the existing entries, and if it is either
intersecting or immediately succeeding/preceeding an existing item it
is merged.
There is currently no attempt made at avoiding iterating over the
existing items in determining whether merging is possible or not.
This patch gets rid of bytesPerCacheLine parameter and makes the DRAM
configuration separate from cache line size. Instead of
bytesPerCacheLine, we define a parameter for the DRAM called
burst_length. The burst_length parameter shows the length of a DRAM
device burst in bits. Also, lines_per_rowbuffer is replaced with
device_rowbuffer_size to improve code portablity.
This patch adds a burst length in beats for each memory type, an
interface width for each memory type, and the memory controller model
is extended to reason about "system" packets vs "dram" packets and
assemble the responses properly. It means that system packets larger
than a full burst are split into multiple dram packets.
This patch adds a packet queue in SimpleMemory to avoid using the
packet queue in the port (and thus have no involvement in the flow
control). The port queue was bound to 100 packets, and as the
SimpleMemory is modelling both a controller and an actual RAM, it
potentially has a large number of packets in flight. There is
currently no limit on the number of packets in the memory controller,
but this could easily be added in a follow-on patch.
As a result of the added internal storage, the functional access and
draining is updated. Some minor cleaning up and renaming has also been
done.
The memtest regression changes as a result of this patch and the stats
will be updated.
Some of the code in StateMachine.py file is added to all the controllers and
is independent of the controller definition. This code is being moved to the
AbstractController class which is the parent class of all controllers.
This patch removes the notion of a peer block size and instead sets
the cache line size on the system level.
Previously the size was set per cache, and communicated through the
interconnect. There were plenty checks to ensure that everyone had the
same size specified, and these checks are now removed. Another benefit
that is not yet harnessed is that the cache line size is now known at
construction time, rather than after the port binding. Hence, the
block size can be locally stored and does not have to be queried every
time it is used.
A follow-on patch updates the configuration scripts accordingly.
This code seems not to be of any use now. There is no path in the simulator
that allows for reconfiguring the network. A better approach would be to
take a checkpoint and start the simulation from the checkpoint with the new
configuration.
This patch reorganizes the cache tags to allow more flexibility to
implement new replacement policies. The base tags class is now a
clocked object so that derived classes can use a clock if they need
one. Also having deriving from SimObject allows specialized Tag
classes to be swapped in/out in .py files.
The cache set is now templatized to allow it to contain customized
cache blocks with additional informaiton. This involved moving code to
the .hh file and removing cacheset.cc.
The statistics belonging to the cache tags are now including ".tags"
in their name. Hence, the stats need an update to reflect the change
in naming.
This patch adds the notion of source- and derived-clock domains to the
ClockedObjects. As such, all clock information is moved to the clock
domain, and the ClockedObjects are grouped into domains.
The clock domains are either source domains, with a specific clock
period, or derived domains that have a parent domain and a divider
(potentially chained). For piece of logic that runs at a derived clock
(a ratio of the clock its parent is running at) the necessary derived
clock domain is created from its corresponding parent clock
domain. For now, the derived clock domain only supports a divider,
thus ensuring a lower speed compared to its parent. Multiplier
functionality implies a PLL logic that has not been modelled yet
(create a separate clock instead).
The clock domains should be used as a mechanism to provide a
controllable clock source that affects clock for every clocked object
lying beneath it. The clock of the domain can (in a future patch) be
controlled by a handler responsible for dynamic frequency scaling of
the respective clock domains.
All the config scripts have been retro-fitted with clock domains. For
the System a default SrcClockDomain is created. For CPUs that run at a
different speed than the system, there is a seperate clock domain
created. This domain incorporates the CPU and the associated
caches. As before, Ruby runs under its own clock domain.
The clock period of all domains are pre-computed, such that no virtual
functions or multiplications are needed when calling
clockPeriod. Instead, the clock period is pre-computed when any
changes occur. For this to be possible, each clock domain tracks its
children.
This patch removes the explicit setting of the clock period for
certain instances of CoherentBus, NonCoherentBus and IOCache where the
specified clock is same as the default value of the system clock. As
all the values used are the defaults, there are no performance
changes. There are similar cases where the toL2Bus is set to use the
parent CPU clock which is already the default behaviour.
The main motivation for these simplifications is to ease the
introduction of clock domains.
This patch does a bit of tidying up in the bridge code, adding const
where appropriate and also removing redundant checks and adding a few
new ones.
There are no changes to the behaviour of any regressions.
This patch fixes the CommMonitor local variable names, and also
introduces a variable to capture if it expects to see a response. The
latter check considers both needsResponse and memInhibitAsserted.
This patch fixes an outstanding issue in the cache timing calculations
where an atomic access returned a time in Cycles, but the port
forwarded it on as if it was in Ticks.
A separate patch will update the regression stats.
This patch changes the updards snoop packet to avoid allocating and
later deleting it. As the code executes in 0 time and the lifetime of
the packet does not extend beyond the block there is no reason to heap
allocate it.
This patch adds separate actions for requests that missed in the local cache
and messages were sent out to get the requested line. These separate actions
are required for differentiating between the hit and miss latencies in the
statistics collected.
This patch adds separate actions for requests that missed in the local cache
and messages were sent out to get the requested line. These separate actions
are required for differentiating between the hit and miss latencies in the
statistics collected.
The patch started of with removing the global variables from the profiler for
profiling the miss latency of requests made to the cache. The corrresponding
histograms have been moved to the Sequencer. These are combined together when
the histograms are printed. Separate histograms are now maintained for
tracking latency of all requests together, of hits only and of misses only.
A particular set of histograms used to use the type GenericMachineType defined
in one of the protocol files. This patch removes this type. Now, everything
that relied on this type would use MachineType instead. To do this, SLICC has
been changed so that multiple machine types can be declared by a controller
in its preamble.
This patch removes the following three files: RubySlicc_Profiler.sm,
RubySlicc_Profiler_interface.cc and RubySlicc_Profiler_interface.hh.
Only one function prototyped in the file RubySlicc_Profiler.sm. Rest of the
code appearing in any of these files is not in use. Therefore, these files
are being removed.
That one single function, profileMsgDelay(), is being moved to the protocol
files where it is in use. If we need any of these deleted functions, I think
the right way to make them visible is to have the AbstractController class in
a .sm and let the controller state machine inherit from this class. The
AbstractController class can then have the prototypes of these profiling
functions in its definition.
2013-06-24 08:59:08 -05:00
Joel Hestness ext:(%2C%20Nilay%20Vaish%20%3Cnilay%40cs.wisc.edu%3E)
The m_size variable attempted to track m_prio_heap.size(), but it did so
incorrectly due to the functions reanalyzeMessages and reanalyzeAllMessages().
Since this variable is intended to track m_prio_heap.size(), we can simply
replace instances where m_size is referenced with m_prio_heap.size(), which
has the added bonus of removing the need for m_size.
Note: This patch also removes an extraneous DPRINTF format string designator
from reanalyzeAllMessages()
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Previously, .sm files were allowed to use the same name for a type and a
variable. This is unnecessarily confusing and has some bad side effects, like
not being able to declare later variables in the same scope with the same type.
This causes the compiler to complain and die on things like Address Address.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Change all occurrances of Address as a variable name to instead use Addr.
Address is an allowed name in slicc even when Address is also being used as a
type, leading to declarations of "Address Address". While this works, it
prevents adding another field of type Address because the compiler then thinks
Address is a variable name, not type.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Reuse the address finalization code in the TLB instead of replicating
it when handling MMIO. This patch also adds support for injecting
memory mapped IPR requests into the memory system.
This patch removes per processor cycle count, histogram for filter stats,
histogram for multicasts, histogram for prefetch wait, some function
prototypes that do not have definitions.
The Profiler class does not need an event for dumping statistics
periodically. This is because there is a method for dumping statistics
for all the sim objects periodically. Since Ruby is a sim object, its
statistics are also included.
This moves event and transition count statistics for cache controllers to
gem5's statistics. It does the same for the statistics associated with the
memory controller in ruby.
All the cache/directory/dma controllers individually collect the event and
transition counts. A callback function, collateStats(), has been added that
is invoked on the controller version 0 of each controller class. This
function adds all the individual controller statistics to a vector
variables. All the code for registering the statistical variables and
collating them is generated by SLICC. The patch removes the files
*_Profiler.{cc,hh} and *_ProfileDumper.{cc,hh} which were earlier used for
collecting and dumping statistics respectively.
This patch changes the class names of the variuos DRAM configurations
to better reflect what memory they are based on. The speed and
interface width is now part of the name, and also the alias that is
used to select them on the command line.
Some minor changes are done to the actual parameters, to better
reflect the named configurations. As a result of these changes the
regressions change slightly and the stats will be bumped in a separate
patch.
This patch adds a histogram to track how many bytes are accessed in an
open row before it is closed. This metric is useful in characterising
a workload and the efficiency of the DRAM scheduler. For example, a
DDR3-1600 device requires 44 cycles (tRC) before it can activate
another row in the same bank. For a x32 interface (8 bytes per cycle)
that means 8 x 44 = 352 bytes must be transferred to hide the
preparation time.
This patch adds a frontend and backend static latency to the DRAM
controller by delaying the responses. Two parameters expressing the
frontend and backend contributions in absolute time are added to the
controller, and the appropriate latency is added to the responses when
adding them to the (infinite) queued port for sending.
For writes and reads that hit in the write buffer, only the frontend
latency is added. For reads that are serviced by the DRAM, the static
latency is the sum of the pipeline latencies of the entire frontend,
backend and PHY. The default values are chosen based on having roughly
10 pipeline stages in total at 500 MHz.
In the future, it would be sensible to make the controller use its
clock and convert these latencies (and a few of the DRAM timings) to
cycles.
This patch does some minor tidying up of the MSHR and MSHRQueue. The
clean up started as part of some ad-hoc tracing and debugging, but
seems worthwhile enough to go in as a separate patch.
The highlights of the changes are reduced scoping (private) members
where possible, avoiding redundant new/delete, and constructor
initialisation to please static code analyzers.
This patch introduces a mirrored internal snoop port to facilitate
easy addition of flow control for the snoop responses that are turned
into normal responses on their return. To perform this, the slave
ports of the coherent bus are wrapped in internal master ports that
are passed as the source ports to the response layer in question.
As a result of this patch, there is more contention for the response
resources, and as such system performance will decrease slightly.
A consequence of the mirrored internal port is that the port the bus
tells to retry (the internal one) and the port actually retrying (the
mirrored) one are not the same. Thus, the existing check in tryTiming
is not longer correct. In fact, the test is redundant as the layer is
only in the retry state while calling sendRetry on the waiting port,
and if the latter does not immediately call the bus then the retry
state is left. Consequently the check is removed.
This patch makes the buses multi layered, and effectively creates a
crossbar structure with distributed contention ports at the
destination ports. Before this patch, a bus could have a single
request, response and snoop response in flight at any time, and with
these changes there can be as many requests as connected slaves (bus
master ports), and as many responses as connected masters (bus slave
ports).
Together with address interleaving, this patch enables us to create
high-throughput memory interconnects, e.g. 50+ GByte/s.
This patch makes the flow control and state updates of the coherent
bus more clear by separating the two cases, i.e. forward as a snoop
response, or turn it into a normal response.
With this change it is also more clear what resources are being
occupied, and that we effectively bypass the busy check for the second
case. As a result of the change in resource usage some stats change.
This patch does some minor housekeeping on the bus code, removing
redundant code, and moving the extraction of the destination id to the
top of the functions using it.
This patch adds a basic set of stats which are hard to impossible to
implement using only communication monitors, and are needed for
insight such as bus utilization, transactions through the bus etc.
Stats added include throughput and transaction distribution, and also
a two-dimensional vector capturing how many packets and how much data
is exchanged between the masters and slaves connected to the bus.
This patch changes the set used to track outstanding requests to an
unordered set (part of C++11 STL). There is no need to maintain the
order, and hopefully there might even be a small performance benefit.
This patch adds a typical (leaning towards fast) LPDDR3 configuration
based on publically available data. As expected, it looks very similar
to the LPDDR2-S4 configuration, only with a slightly lower burst time.
This patch adapts the existing LPDDR2 configuration to make use of the
multi-channel functionality. Thus, to get a x64 interface two
controllers should be instantiated using the makeMultiChannel method.
The page size and ranks are also adapted to better suit with a typical
LPDDR2 part.
This patch removes the explicit memset as it is redundant and causes
the simulator to touch the entire space, forcing the host system to
allocate the pages.
Anonymous pages are mapped on the first access, and the page-fault
handler is responsible for zeroing them. Thus, the pages are still
zeroed, but we avoid touching the entire allocated space which enables
us to use much larger memory sizes as long as not all the memory is
actually used.
This patch changes the way cache statistics are collected in ruby.
As of now, there is separate entity called CacheProfiler which holds
statistical variables for caches. The CacheMemory class defines different
functions for accessing the CacheProfiler. These functions are then invoked
in the .sm files. I find this approach opaque and prone to error. Secondly,
we probably should not be paying the cost of a function call for recording
statistics.
Instead, this patch allows for accessing statistical variables in the
.sm files. The collection would become transparent. Secondly, it would happen
in place, so no function calls. The patch also removes the CacheProfiler class.
--HG--
rename : src/mem/slicc/ast/InfixOperatorExprAST.py => src/mem/slicc/ast/OperatorExprAST.py
The existing implementation can read uninitialized data or stale information
from the cached PageTable entries.
1) Add a valid bit for the cache entries. Simply using zero for the virtual
address to signify invalid entries is not sufficient. Speculative, wrong-path
accesses frequently access page zero. The current implementation would return
a uninitialized TLB entry when address zero was accessed and the PageTable
cache entry was invalid.
2) When unmapping/mapping/remaping a page, invalidate the corresponding
PageTable cache entry if one already exists.
Due to recent changes to clocking system in Ruby and the way Ruby restores
state from a checkpoint, garnet was failing to run from a checkpointed state.
The problem is that Ruby resets the time to zero while warming up the caches.
If any component records a local copy of the time (read calls curCycle())
before the simulation has started, then that component will not operate until
that time is reached. In the context of this particular patch, the Garnet
Network class calls curCycle() at multiple places. Any non-operational
component can block in requests in the memory system, which the system
interprets as a deadlock. This patch makes changes so that Garnet can
successfully run from checkpointed state.
It adds a globally visible time at which the actual execution started. This
time is initialized in RubySystem::startup() function. This variable is only
meant for components with in Ruby. This replaces the private variable that
was maintained within Garnet since it is not possible to figure out the
correct time when the value of this variable can be set.
The patch also does away with all cases where curCycle() is called with in
some Ruby component before the system has actually started executing. This
is required due to the quirky manner in which ruby restores from a checkpoint.
This patch adds an address mapping scheme where the channel
interleaving takes place on a cache line granularity. It is similar to
the existing RaBaChCo that interleaves on a DRAM page, but should give
higher performance when there is less locality in the address
stream.
This patch changes the slightly ambigious names used for the address
mapping scheme to be more descriptive, and actually spell out what
they do. With this patch we also open up for adding more flavours of
open- and close-type mappings, i.e. interleaving across channels with
the open map.
This patch adds a WideIO 200 MHz configuration that can be used as a
baseline to compare with DDRx and LPDDRx. Note that it is a single
channel and that it should be replicated 4 times. It is based on
publically available information and attempts to capture an envisioned
8 Gbit single-die part (i.e. without TSVs).
This patch provides useful printouts throughut the memory system. This
includes pretty-printed cache tags and function call messages
(call-stack like).
This patch changes the SimpleTimingPort and RubyPort to panic on
inhibited requests as this should never happen in either of the
cases. The SimpleTimingPort is only used for the I/O devices PIO port
and the DMA devices config port and should thus never see an inhibited
request. Similarly, the SimpleTimingPort is also used for the
MessagePort in x86, and there should also not be any cases where the
port sees an inhibited request.
Previously, nextCycle() could return the *current* cycle if the current tick was
already aligned with the clock edge. This behavior is not only confusing (not
quite what the function name implies), but also caused problems in the
drainResume() function. When exiting/re-entering the sim loop (e.g., to take
checkpoints), the CPUs will drain and resume. Due to the previous behavior of
nextCycle(), the CPU tick events were being rescheduled in the same ticks that
were already processed before draining. This caused divergence from runs that
did not exit/re-entered the sim loop. (Initially a cycle difference, but a
significant impact later on.)
This patch separates out the two behaviors (nextCycle() and clockEdge()),
uses nextCycle() in drainResume, and uses clockEdge() everywhere else.
Nothing (other than name) should change except for the drainResume timing.
When using the o3 or inorder CPUs with many Ruby protocols, the caches may
need to forward invalidations to the CPUs. The RubyPort was instantiating a
packet to be sent to the CPUs to signal the eviction, but the packets were
not being freed by the CPUs. Consistent with the classic memory model, stack
allocate the packet and heap allocate the request so on
ruby_eviction_callback() completion, the packet deconstructor is called, and
deletes the request (*Note: stack allocating the request causes double
deletion, since it will be deleted in the packet destructor). This results in
the least memory allocations without memory errors.
When warming up caches in Ruby, the CacheRecorder sends fetch requests into
Ruby Sequencers with packet types that require responses. Since responses are
never generated for these CacheRecorder requests, the requests are not deleted
in the packet destructor called from the Ruby hit callback. Free the request.
This allows you to have (i.e.) an L2 cache that is not named "L2Cache"
but is still a GenericMachineType_L2Cache. This is particularly
helpful if the protocol has multiple L2 controllers.
When Ruby stats are printed for events and transitions, they include stats
for all of the controllers of the same type, but they are not necessarily
printed in order of the controller ID "version", because of the way the
profilers were added to the profiler vector. This patch fixes the push order
problem so that the stats are printed in ascending order 0->(# controllers),
so statistics parsers may correctly assume the controller to which the stats
belong.
When connecting message buffers between Ruby controllers, it is
easy to mistakenly connect multiple controllers to the same message
buffer. This patch prints a more descriptive fatal message than the
previous assert statement in order to facilitate easier debugging.
The cache trace variables are array allocated uint8_t* in the RubySystem and
the Ruby CacheRecorder, but the code used delete to free the memory, resulting
in Valgrind memory errors. Change these deletes to delete [] to get rid of the
errors.
Fixes a latency calculation bug for accesses during a cache line fill.
Under a cache miss, before the line is filled, accesses to the cache are
associated with a MSHR and marked as targets. Once the line fill completes,
MSHR target packets pay an additional latency of
"responseLatency + busSerializationLatency". However, the "whenReady"
field of the cache line is only set to an additional delay of
"busSerializationLatency". This lacks the responseLatency component of
the fill. It is possible for accesses that occur on the cycle of
(or briefly after) the line fill to respond without properly paying the
responseLatency. This also creates the situation where two accesses to the
same address may be serviced in an order opposite of how they were received
by the cache. For stores to the same address, this means that although the
cache performs the stores in the order they were received, acknowledgements
may be sent in a different order.
Adding the responseLatency component to the whenReady field preserves the
penalty that should be paid and prevents these ordering issues.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch solves the corner case scenario where the sendRetryEvent could be
scheduled twice, when an io device stresses the IOcache in the system. This
should not be possible in the cache system.
This patch splits the retryList into a list of ports that are waiting
for the bus itself to become available, and a map that tracks the
ports where forwarding failed due to a peer not accepting the
packet. Thus, when a retry reaches the bus, it can be sent to the
appropriate port that initiated that transaction.
As a consequence of this patch, only ports that are really ready to go
will get a retry, thus reducing the amount of redundant failed
attempts. This patch also makes it easier to reason about the order of
servicing requests as the ports waiting for the bus are now clearly
FIFO and much easier to change if desired.
This patch introduces a variable to keep track of the retrying port
instead of relying on it being the front of the retryList.
Besides the improvement in readability, this patch is a step towards
separating out the two cases where a port is waiting for the bus to be
free, and where the forwarding did not succeed and the bus is waiting
for a retry to pass on to the original initiator of the transaction.
The changes made are currently such that the regressions are not
affected. This is ensured by always prioritizing the currently
retrying port and putting it back at the front of the retry list.
This patch adds an optional flags field to the packet trace to encode
the request flags that contain information about whether the request
is (un)cacheable, instruction fetch, preftech etc.
A recent set of patches added support for multiple clock domains to ruby.
I had made some errors while writing those patches. The sender was using
the receiver side clock while enqueuing a message in the buffer. Those
errors became visible while creating (or restoring from) checkpoints. The
errors also become visible when a multi eventq scenario occurs.
The message buffer node used to keep time in terms of Cycles. Since the
sender and the receiver can have different clock periods, storing node
time in cycles requires some conversion. Instead store the time directly
in Ticks.
A set of patches was recently committed to allow multiple clock domains
in ruby. In those patches, I had inadvertently made an incorrect use of
the clocks. Suppose object A needs to schedule an event on object B. It
was possible that A accesses B's clock to schedule the event. This is not
possible in actual system. Hence, changes are being to the Consumer class
so as to avoid such happenings. Note that in a multi eventq simulation,
this can possibly lead to an incorrect simulation.
There are two functions in the Consumer class that are used for scheduling
events. The first function takes in the relative delay over the current time
as the argument and adds the current time to it for scheduling the event.
The second function takes in the absolute time (in ticks) for scheduling the
event. The first function is now being moved to protected section of the
class so that only objects of the derived classes can use it. All other
objects will have to specify absolute time while scheduling an event
for some consumer.
The histogram for tracking outstanding counts per cycle is maintained
in the profiler. For a parallel implementation of the memory system, we
need that this histogram is maintained locally. Hence it will now be
kept in the sequencer itself. The resulting histograms will be merged
when the stats are printed.
These functions are currently implemented in one of the files related to Slicc.
Since these are purely C++ functions, they are better suited to be in the base
class.
This patch modifies ruby so that two controllers can be connected to each
other with only message buffers in between. Before this patch, all the
controllers had to be connected to the network for them to communicate
with each other. With this patch, one can have protocols where a controller
is not connected to the network, but communicates with another controller
through a message buffer.
The Topology class in Ruby does not need to inherit from SimObject class.
This patch turns it into a regular class. The topology object is now created
in the constructor of the Network class. All the parameters for the topology
class have been moved to the network class.
The functional write code was assuming that all writes are block sized,
which may not be true for Ruby Requests. This bug can lead to a buffer
overflow.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This check covers a case where a retry is called from the SimpleDRAM
causing a new request to appear before the DRAM itself schedules a
nextReqEvent. By adding this check, the event is not scheduled twice.
This patch adds a class method that allows easy creation of
channel-interleaved multi-channel DRAM configurations. It is enabled
by a class method to allow customisation of the class independent of
the channel configuration. For example, the user can create a MyDDR
subclass of e.g. SimpleDDR3, and then create a four-channel
configuration of the subclass by calling MyDDR.makeMultiChannel(4,
mem_start, mem_size).
This patch fixes a number of small cosmetic issues in the SimpleDRAM
module. The most important change is to move the accounting of
received packets to after the check is made if the packet should be
retried or not. Thus, packets are only counted if they are actually
accepted.
This patch adds support for multi-channel instances of the DRAM
controller model by stripping away the channel bits in the address
decoding. The patch relies on the availiability of address
interleaving and, at this time, it is up to the user to configure the
interleaving appropriately. At the moment it is assumed that the
channel interleaving bits are immediately following the column bits
(smallest sensible interleaving). Convenience methods for building
multi-channel configurations will be added later.
This patch adds merging of interleaved ranges before creating the
backing stores. The backing stores are always a contigous chunk of the
address space, and with this patch it is possible to have interleaved
memories in the system.
This patch adds basic merging of address ranges to the bus, such that
interleaved ranges are merged together before being passed on by the
bus. As such, the bus aggregates the address ranges of the connected
slave ports and then passes on the merged ranges through its master
ports. The bus thus hides the complexity of the interleaved ranges and
only exposes contigous ranges to the surrounding system.
As part of this patch, the bus ranges are also cached for any future
queries.
The MESI CMP directory coherence protocol, while transitioning from SM to IM,
did not invalidate the lock that it might have taken on a cache line. This
patch adds an action for doing so.
The problem was found by Dibakar, but I was not happy with his proposed
solution. So I implemented a different solution.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch fixes a newly introduced bug where the sender state was
popped before checking that it should be. Amazingly all regressions
pass, but Linux fails to boot on the detailed CPU with caches enabled.
This patch fixes the warnings that clang3.2svn emit due to the "-Wall"
flag. There is one case of an uninitialised value in the ARM neon ISA
description, and then a whole range of unused private fields that are
pruned.
This patch address the most important name shadowing warnings (as
produced when using gcc/clang with -Wshadow). There are many
locations where constructor parameters and function parameters shadow
local variables, but these are left unchanged.
This patch adds a check to ensure that the delay incurred by
the bus is not simply disregarded, but accounted for by someone. At
this point, all the modules do is to zero it out, and no additional
time is spent. This highlights where the bus timing is simply dropped
instead of being paid for.
As a follow up, the locations identified in this patch should add this
additional time to the packets in one way or another. For now it
simply acts as a sanity check and highlights where the delay is simply
ignored.
Since no time is added, all regressions remain the same.
This patch changes the names of the cache accessor functions to be in
line with those used by the ports. This is done to avoid confusion and
get closer to a one-to-one correspondence between the interface of the
memory object (the cache in this case) and the port itself.
The member function timingAccess has been split into a snoop/non-snoop
part to avoid branching on the isResponse() of the packet.
This patch changes the bus-related time accounting done in the packet
to be relative. Besides making it easier to align the cache timing to
cache clock cycles, it also makes it possible to create a Last-Level
Cache (LLC) directly to a memory controller without a bus inbetween.
The bus is unique in that it does not ever make the packets wait to
reflect the time spent forwarding them. Instead, the cache is
currently responsible for making the packets wait. Thus, the bus
annotates the packets with the time needed for the first word to
appear, and also the last word. The cache then delays the packets in
its queues before passing them on. It is worth noting that every
object attached to a bus (devices, memories, bridges, etc) should be
doing this if we opt for keeping this way of accounting for the bus
timing.
This patch removes the time field from the packet as it was only used
by the preftecher. Similar to the packet queue, the prefetcher now
wraps the packet in a deferred packet, which also has a tick
representing the absolute time when the packet should be sent.
This patch makes the clock member private to the ClockedObject and
forces all children to access it using clockPeriod(). This makes it
impossible to inadvertently change the clock, and also makes it easier
to transition to a situation where the clock is derived from e.g. a
clock domain, or through a multiplier.
This patch fixes a potential deadlock in the caches. This deadlock
could occur when more than one cache is used in a system, and
pkt->senderState is modified in between the two caches. This happened
as the caches relied on the senderState remaining unchanged, and used
it for instantaneous upstream communication with other caches.
This issue has been addressed by iterating over the linked list of
senderStates until we are either able to cast to a MSHR* or
senderState is NULL. If the cast is successful, we know that the
packet has previously passed through another cache, and therefore
update the downstreamPending flag accordingly. Otherwise, we do
nothing.
This patch adds a predecessor field to the SenderState base class to
make the process of linking them up more uniform, and enable a
traversal of the stack without knowing the specific type of the
subclasses.
There are a number of simplifications done as part of changing the
SenderState, particularly in the RubyTest.
This patch fixes a bug in the CommMonitor caused by the packet being
modified before it is captured in the trace. By recording the fields
before passing the packet on, and then putting these values in the
trace we ensure that even if the packet is modified the trace captures
what the CommMonitor saw.
This patch merely adopts a more strict use of const for the cache
member functions and variables, and also moves a large portion of the
member functions from public to protected.
Virtualized CPUs and the fastmem mode of the atomic CPU require direct
access to physical memory. We currently require caches to be disabled
when using them to prevent chaos. This is not ideal when switching
between hardware virutalized CPUs and other CPU models as it would
require a configuration change on each switch. This changeset
introduces a new version of the atomic memory mode,
'atomic_noncaching', where memory accesses are inserted into the
memory system as atomic accesses, but bypass caches.
To make memory mode tests cleaner, the following methods are added to
the System class:
* isAtomicMode() -- True if the memory mode is 'atomic' or 'direct'.
* isTimingMode() -- True if the memory mode is 'timing'.
* bypassCaches() -- True if caches should be bypassed.
The old getMemoryMode() and setMemoryMode() methods should never be
used from the C++ world anymore.
The transition for state MII and event Store was found missing during testing.
The transition is being added. The controller will not stall the Store request
in state MII
This patch allows ruby to have multiple clock domains. As I understand
with this patch, controllers can have different frequencies. The entire
network needs to run at a single frequency.
The idea is that with in an object, time is treated in terms of cycles.
But the messages that are passed from one entity to another should contain
the time in Ticks. As of now, this is only true for the message buffers,
but not for the links in the network. As I understand the code, all the
entities in different networks (simple, garnet-fixed, garnet-flexible) should
be clocked at the same frequency.
Another problem is that the directory controller has to operate at the same
frequency as the ruby system. This is because the memory controller does
not make use of the Message Buffer, and instead implements a buffer of its
own. So, it has no idea of the frequency at which the directory controller
is operating and uses ruby system's frequency for scheduling events.
This patch is as of now the final patch in the series of patches that replace
Time with Cycles.This patch further replaces Time with Cycles in Sequencer,
Profiler, different protocols and related entities.
Though Time has not been completely removed, the places where it is in use
seem benign as of now.
The patch started of with replacing Time with Cycles in the Consumer class.
But to get ruby to compile, the rest of the changes had to be carried out.
Subsequent patches will further this process, till we completely replace
Time with Cycles.
This patch modifies the Histogram class' add() function so that it can add
linear histograms as well. The function assumes that the left end point of
the ranges of the two histograms are the same. It also assumes that when
the ranges of the two histogram are changed to accomodate an element not in
the range, the factor used in changing the range is same for both the
histograms.
This function is then used in removing one of the calls to the global
profiler*. The histograms for recording the delays incurred in processing
different requests are now maintained by the controllers. The profiler
adds these histograms when it needs to print the stats.
This patch does several things. First, the counter for fully busy cycles for a
controller is now kept with in the controller, instead of being part of the profiler.
Second, the topology class no longer keeps an array of controllers which was only
used for printing stats. Instead, ruby system will now ask each controller to print
the stats. Thirdly, the statistical variable for recording how many different types
were created is being moved in to the controller from the profiler. Note that for
printing, the profiler will collate results from different controllers.
The number of bits required for an address was set to floorLog2(memory size).
This is correct under the assumption that the memory size is a power of 2,
which is not always true. Hence, floorLog2 is being replaced with ceilLog2.
This patch moves the default DRAM parameters from the SimpleDRAM class
to two different subclasses, one for DDR3 and one for LPDDR2. More can
be added as we go forward.
The regressions that previously used the SimpleDRAM are now using
SimpleDDR3 as this is the most similar configuration.
This patch adds two additional scheduling constraints to the DRAM
controller model, to constrain the activation rate. The two metrics
are determine the size of the activation window in terms of the number
of activates and the minimum time required for that number of
activates. This maps to current DDRx, LPDDRx and WIOx standards that
have either tFAW (4 activate window) or tTAW (2 activate window)
scheduling constraints.
This patch changes how the data bus busy time is calculated such that
it is delayed to the actual scheduling time of the request as opposed
to being done as soon as possible.
This patch changes a bunch of statistics, and the stats update is
bundled together with the introruction of tFAW/tTAW and the named DRAM
configurations like DDR3 and LPDDR2.
the cache drainManager is set but never cleared, this is because
the cache itself does not need to be drained and thus never
triggers a signalDrainDone(). because the drainManager variable
is not used properly and does not appear to be necessary it has
been removed with this patch.
The panic() function already prints the current tick value. This call to
curCycle() is as such redundant. Since we are trying to move towards multiple
clock domains, this call will print misleading time.
This patch converts the panic() print outs in the Sequencer::wakeup()
call from ruby cycles to Ticks(). This makes it easier to debug deadlocks
with the ProtocolTrace flag so the issue time indicated in the panic message
can be quickly searched for.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch was initiated so as to remove reference to g_system_ptr,
the pointer to Ruby System that is used for getting the current time.
That simple change actual requires changing a lot many things in slicc and
garnet. All these changes are related to how time is handled.
In most of the places, g_system_ptr has been replaced by another clock
object. The changes have been done under the assumption that all the
components in the memory system are on the same clock frequency, but the
actual clocks might be distributed.
Many Ruby structures inherit from the Consumer, which is used for scheduling
events. The Consumer used to relay on an Event Manager for scheduling events
and on g_system_ptr for time. With this patch, the Consumer will now use a
ClockedObject to schedule events and to query for current time. This resulted
in several structures being converted from SimObjects to ClockedObjects. Also,
the MessageBuffer class now requires a pointer to a ClockedObject so as to
query for time.
The current implementation in gem5 just keeps a list of locks per cacheline.
Due to this, a store to a non-overlapping portion of the cacheline can cause an
LL/SC pair to fail. This patch simply adds an address range to the lock
structure, so that the lock is only invalidated if the store overlaps the lock
range.
Running with valgrind I noticed a use after free originating from
simple_mem.cc. It looks like this is a known issue and this additional call
site was missed in an earlier patch.
When the classic gem5 cache sees an uncacheable memory access, it used
to ignore it or silently drop the cache line in case of a
write. Normally, there shouldn't be any data in the cache belonging to
an uncacheable address range. However, since some architecture models
don't implement cache maintenance instructions, there might be some
dirty data in the cache that is discarded when this happens. The
reason it has mostly worked before is because such cache lines were
most likely evicted by normal memory activity before a TLB flush was
requested by the OS.
Previously, the cache model would invalidate cache lines when they
were accessed by an uncacheable write. This changeset alters this
behavior so all uncacheable memory accesses cause a cache flush with
an associated writeback if necessary. This is implemented by reusing
the cache flushing machinery used when draining the cache, which
implies that writebacks are performed using functional accesses.
The IIC replacement policy seems to be unused and has probably
gathered too much bit rot to be useful. This patch removes the IIC and
its associated cache parameters.
This patch adds basic merging of address ranges when determining which
address ranges should be reported in the configuration table. By
performing this merging it is possible to distribute an address range
across many memory channels (controllers). This is essential to enable
address interleaving.
This patch adds support for interleaving bits for the address
ranges. What was previously just a start and end address, now has an
additional three fields, for the high bit, and number of bits to use
for interleaving, and a match value to compare against. If the number
of interleaving bits is set to zero it is effectively disabled.
A number of convenience functions are added to the range to enquire
about the interleaving, its granularity and the number of stripes it
is part of.
This patch cleans up the AddrRangeMap in preparation for the addition
of interleaving by removing unused code. The non-const editions of
find are never used, and hence the duplication is not needed.
This patch tidies up a number of the bus DPRINTFs related to range
manipulation. In particular, it shifts the message about range changes
to the start of the member function, and also adds information about
when all ranges are received.
This patch makes the address mapper less stringent about checking the
before and after ranges, i.e. the original and remapped ranges. The
checks were not really necessary, and there are situations when the
previous checks were too strict.
This patch makes the start and end address private in a move to
prevent direct manipulation and matching of ranges based on these
fields. This is done so that a transition to ranges with interleaving
support is possible.
As a result of hiding the start and end, a number of member functions
are needed to perform the comparisons and manipulations that
previously took place directly on the members. An accessor function is
provided for the start address, and a function is added to test if an
address is within a range. As a result of the latter the != and ==
operator is also removed in favour of the member function. A member
function that returns a string representation is also created to allow
debug printing.
In general, this patch does not add any functionality, but it does
take us closer to a situation where interleaving (and more cleverness)
can be added under the bonnet without exposing it to the user. More on
that in a later patch.
