This patch adds support for interleaving bits for the address
ranges. What was previously just a start and end address, now has an
additional three fields, for the high bit, and number of bits to use
for interleaving, and a match value to compare against. If the number
of interleaving bits is set to zero it is effectively disabled.
A number of convenience functions are added to the range to enquire
about the interleaving, its granularity and the number of stripes it
is part of.
This patch makes the all proxy traverse any potential list that is
encountered in the object hierarchy instead of only looking at
children that are SimObjects. An example of where this is useful is
when creating a multi-channel memory system as a list of controllers,
whilst ensuring that the memories are still visible in the system.
This patch cleans up the AddrRangeMap in preparation for the addition
of interleaving by removing unused code. The non-const editions of
find are never used, and hence the duplication is not needed.
This patch generalises the address range resolution for the I/O cache
and I/O bridge such that they do not assume a single memory. The patch
involves adding a parameter to the system which is then defined based
on the memories that are to be visible from the I/O subsystem, whether
behind a cache or a bridge.
The change is needed to allow interleaved memory controllers in the
system.
This patch tidies up a number of the bus DPRINTFs related to range
manipulation. In particular, it shifts the message about range changes
to the start of the member function, and also adds information about
when all ranges are received.
This patch makes the address mapper less stringent about checking the
before and after ranges, i.e. the original and remapped ranges. The
checks were not really necessary, and there are situations when the
previous checks were too strict.
This patch makes the start and end address private in a move to
prevent direct manipulation and matching of ranges based on these
fields. This is done so that a transition to ranges with interleaving
support is possible.
As a result of hiding the start and end, a number of member functions
are needed to perform the comparisons and manipulations that
previously took place directly on the members. An accessor function is
provided for the start address, and a function is added to test if an
address is within a range. As a result of the latter the != and ==
operator is also removed in favour of the member function. A member
function that returns a string representation is also created to allow
debug printing.
In general, this patch does not add any functionality, but it does
take us closer to a situation where interleaving (and more cleverness)
can be added under the bonnet without exposing it to the user. More on
that in a later patch.
This patch temporarily removes the joining of ranges when creating the
backing store, to reserve this functionality for the interleaved
ranges that are about to be introduced.
When creating the mmaps for the backing store, there is no point in
creating larger contigous chunks that what is necessary. The larger
chunks will only make life more difficult for the host.
Merging will be re-added later, but then only for interleaved ranges.
This patch adds support for reading input traces encoded using
protobuf according to what is done in the CommMonitor.
A follow-up patch adds a Python script that can be used to convert the
previously used ASCII traces to protobuf equivalents. The appropriate
regression input is updated as part of this patch.
This patch encapsulates the traffic generator input in a stream class
such that the parsing is not visible to the trace generator. The
change takes us one step closer to using protobuf-based input traces
for the trace replay.
The functionality of the current input stream is identical to what it
was, and the ASCII format remains the same for now.
This patch adds support for inputting protobuf messages through a
ProtoInputStream which hides the internal streams used by the
library. The stream is created based on the name of an input file and
optionally includes decompression using gzip.
The input stream will start by getting a magic number from the file,
and also verify that it matches with the expected value. Once opened,
messages can be read incrementally from the stream, returning
true/false until an error occurs or the end of the file is reached.
This patch adds packet tracing to the communication monitor using a
protobuf as the mechanism for creating the trace.
If no file is specified, then the tracing is disabled. If a file is
specified, then for every packet that is successfully sent, a protobuf
message is serialized to the file.
This patch adds support for outputting protobuf messages through a
ProtoOutputStream which hides the internal streams used by the
library. The stream is created based on the name of an output file and
optionally includes compression using gzip.
The output stream will start by putting a magic number in the file,
and then for every message that is serialized prepend the size such
that the stream can be written and read incrementally. At this point
this merely serves as a proof of concept.
This patch enables the use of protobuf input files in the build
process, thus allowing .proto files to be added to input. Each .proto
file is compiled using the protoc tool and the newly created C++
source is added to the list of sources.
The first location where the protobufs will be used is in the
capturing and replay of memory traces, involving the communication
monitor and the trace-generator state of the traffic generator. This
will follow in the next patch.
This patch does add a dependency on the availability of the BSD
licensed protobuf library (and headers), and the protobuf compiler,
protoc. These dependencies are checked in the SConstruct, similar to
e.g. swig. The user can override the use of protoc from the PATH by
specifying the PROTOC environment variable.
Although the dependency on libprotobuf and protoc might seem like a
big step, they add significant value to the project going
forward. Execution traces and other types of traces could easily be
added and parsers for C++ and Python are automatically generated. We
could also envision using protobufs for the checkpoints, description
of the traffic-generator behaviour etc. The sky is the limit. We could
also use the GzipOutputStream from the protobuf library instead of the
current GPL gzstream.
Currently, only the C++ source and header is generated. Going forward
we might want to add the Python output to support simple command-line
tools for displaying and editing the traces.
The PL111 model currently maintains a list of pre-allocated
DmaDoneEvents to prevent unnecessary heap allocations. This list
effectively works like a stack where the top element is the latest
scheduled event. When an event triggers, the top pointer is moved down
the stack. This obviously breaks since events usually retire from the
bottom (events don't necessarily have to retire in order), which
triggers the following assertion:
gem5.debug: build/ARM/dev/arm/pl111.cc:460: void Pl111::fillFifo(): \
Assertion `!dmaDoneEvent[dmaPendingNum-1].scheduled()' failed.
This changeset adds a vector listing the currently unused events. This
vector acts like a stack where the an element is popped off the stack
when a new event is needed an pushed on the stack when they trigger.
This patch fixes the Pl111 timings by creating a separate clock for
the pixel timings. The device clock is used for all interactions with
the memory system, just like the AHB clock on the actual module.
The result without this patch is that the module only is allowed to
send one request every tick of the 24MHz clock which causes a huge
backlog.
This patch fixes the computation that determines whether to perform a
read or a write such that the two corner cases (0 and 100) are both
more efficient and handled correctly.
This patch adds a basic check to ensure that the packet queue does not
grow absurdly large. The queue should only be used to store packets
that were delayed due to blocking from the neighbouring port, and not
for actual storage. Thus, a limit of 100 has been chosen for now
(which is already quite substantial).
This patch addresses a warning related to the swig interface
generation for the Switch class. The cxx_header is now specified
correctly, and the header in question has got a few includes added to
make it all compile.
The platform has two KMI devices that are both setup to be keyboards. This
patch changes the second keyboard to a mouse. This patch will allow keyboard
input as usual and additionally provide mouse support.
This patch fixes a bug that caused multiple systems to overwrite each
other physical memory. The system name is now included in the filename
such that this is avoided.
This patch makes the values of ID_ISARx, MIDR, and FPSID configurable
as ISA parameter values. Additionally, setMiscReg now ignores writes
to all of the ID registers.
Note: This moves the MIDR parameter from ArmSystem to ArmISA for
consistency.
The ISA class on stores the contents of ID registers on many
architectures. In order to make reset values of such registers
configurable, we make the class inherit from SimObject, which allows
us to use the normal generated parameter headers.
This patch introduces a Python helper method, BaseCPU.createThreads(),
which creates a set of ISAs for each of the threads in an SMT
system. Although it is currently only needed when creating
multi-threaded CPUs, it should always be called before instantiating
the system as this is an obvious place to configure ID registers
identifying a thread/CPU.
This patch unlocks the cpu-local monitor when the CPU sees a snoop to a locked
address. Previously we relied on the cache to handle the locking for us, however
some users on the gem5 mailing list reported a case where the cpu speculatively
executes a ll operation after a pending sc operation in the pipeline and that
makes the cache monitor valid. This should handle that case by invaliding the
local monitor.
isSyscall was originally created because during handling of a syscall in SE
mode the threadcontext had to be updated. However, in many places this is used
in FS mode (e.g. fault handlers) and the name doesn't make much sense. The
boolean actually stops gem5 from squashing speculative and non-committed state
when a write to a threadcontext happens, so re-name the variable to something
more appropriate
This interface is no longer used, and getting rid of it simplifies the
decoders and code that sets up the decoders. The thread context had been used
to read architectural state which was used to contextualize the instruction
memory as it came in. That was changed so that the state is now sent to the
decoders to keep locally if/when it changes. That's significantly more
efficient.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
The predecoder in x86 does a lot of work, most of which can be skipped if the
decoder cache is put in front of it.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Avoid reading them every instruction, and also eliminate the last use of the
thread context in the decoders.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch implements the fnstsw instruction. The code was originally written
by Vince Weaver. Gabe had made some comments about the code, but those were
never addressed. This patch addresses those comments.
This patch implements the fsincos instruction. The code was originally written
by Vince Weaver. Gabe had made some comments about the code, but those were
never addressed. This patch addresses those comments.
uopSet_uop is microop instruction that has the IsControl flags set, but the
IsCondControl or IsUncondControl flags seems not to be set, neither in
the construction nor where the microop is used. This patch adds the the
flags in the constructor of the instruction (MicroUopSetPCCPSR).
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
A flag was missing for the movret_uop microop instruction. This patch adds
that flag when the instruction is used, not directly in the constructor of
the instruction.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
The directed tester supports only generating only read or only write accesses. The
patch modifies the tester to support streams that have both read and write accesses.
The patch adds support to slicc for recognizing arguments that should be
passed to the constructor of a class. I did not like the fact that an explicit
check was being carried on the type 'TBETable' to figure out the arguments to
be passed to the constructor.
The patch also moves some of the member variables that are declared for all
the controllers to the base class AbstractController.
This patch adds a prefetcher for the ruby memory system. The prefetcher
is based on a prefetcher implemented by others (well, I don't know
who wrote the original). The prefetcher does stride-based prefetching,
both unit and non-unit. It obseves the misses in the cache and trains on
these. After the training period is over, the prefetcher starts issuing
prefetch requests to the controller.
globalHistoryBits, globalPredictorSize, and choicePredictorSize are decoupled.
globalHistoryBits controls how much history is kept, global and choice
predictor sizes control how much of that history is used when accessing
predictor tables. This way, global and choice predictors can actually be
different sizes, and it is no longer possible to walk off the predictor arrays
and cause a seg fault.
There are now individual thresholds for choice, global, and local saturating
counters, so that taken/not taken decisions are correct even when the
predictors' counters' sizes are different.
The interface for localPredictorSize has been removed from TournamentBP because
the value can be calculated from localHistoryBits.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch adds a _curTick variable to an eventq. This variable is updated
whenever an event is serviced in function serviceOne(), or all events upto
a particular time are processed in function serviceEvents(). This change
helps when there are eventqs that do not make use of curTick for scheduling
events.
Recent changes to functionalRead() in the memory system was not correct.
The change allowed for returning data from the first message found in
the buffers of the memory system. This is not correct since it is possible
that a timing message has data from an older state of the block.
The changes are being reverted.
This patch fixes the draining of the SimpleDRAM controller model. The
controller performs buffering of writes and normally there is no need
to ever empty the write buffer (if you have a fast on-chip memory,
then use it). The patch adds checks to ensure the write buffer is
drained when the controller is asked to do so.
This patch adds support to ruby so that the statistics maintained by ruby
are reset/dumped when the statistics for the rest of the system are
reset/dumped. For resetting the statistics, ruby now provides the
resetStats() function that a sim object can provide. As a consequence, the
clearStats() function has been removed from RubySystem. For dumping stats,
Ruby now adds a callback event to the dumpStatsQueue. The exit callback that
ruby used to add earlier is being removed.
Created by: Hamid Reza Khaleghzadeh.
Improved by: Lluc Alvarez, Nilay Vaish
Committed by: Nilay Vaish
This patch adds support for the following optional drain methods in
the classical memory system's cache model:
memWriteback() - Write back all dirty cache lines to memory using
functional accesses.
memInvalidate() - Invalidate all cache lines. Dirty cache lines
are lost unless a writeback is requested.
Since memWriteback() is called when checkpointing systems, this patch
adds support for checkpointing systems with caches. The serialization
code now checks whether there are any dirty lines in the cache. If
there are dirty lines in the cache, the checkpoint is flagged as bad
and a warning is printed.
This patch adds the following two methods to the Drainable base class:
memWriteback() - Write back all dirty cache lines to memory using
functional accesses.
memInvalidate() - Invalidate memory system buffers. Dirty data
won't be written back.
Specifying calling memWriteback() after draining will allow us to
checkpoint systems with caches. memInvalidate() can be used to drop
memory system buffers in preparation for switching to an accelerated
CPU model that bypasses the gem5 memory system (e.g., hardware
virtualized CPUs).
Note: This patch only adds the methods to Drainable, the code for
flushing the TLB and the cache is committed separately.
This changeset adds a SWIG interface for the Serializable class, which
fixes a warning when compiling the SWIG interface for the event
queue. Currently, the only method exported is the name() method.
There is no point in exporting the old drain() method in
Simulate.py. It should only be used internally by doDrain(). This
patch moves the old drain() method into doDrain() and renames
doDrain() to drain().
changeToAtomic and changeToTiming both do essentially the same thing,
they check the type of their input argument, drain the system, and
switch to the desired memory mode. This patch moves all of that code
to a separate method (changeMemoryMode) and calls that from both
changeToAtomic and changeToTiming.
This patch moves the draining interface from SimObject to a separate
class that can be used by any object needing draining. However,
objects not visible to the Python code (i.e., objects not deriving
from SimObject) still depend on their parents informing them when to
drain. This patch also gets rid of the CountedDrainEvent (which isn't
really an event) and replaces it with a DrainManager.
SWIG needs a complete declaration of all wrapped objects. This patch
adds a header file with the DerivO3CPU class and includes it in the
SWIG interface.
--HG--
rename : src/cpu/o3/cpu_builder.cc => src/cpu/o3/deriv.cc
In order to create reliable SWIG wrappers, we need to include the
declaration of the wrapped class in the SWIG file. Previously, we
didn't expose the declaration of checker CPUs. This patch adds header
files for such CPUs and include them in the SWIG wrapper.
--HG--
rename : src/cpu/dummy_checker_builder.cc => src/cpu/dummy_checker.cc
rename : src/cpu/o3/checker_builder.cc => src/cpu/o3/checker.cc
The Python wrappers and the C++ should have the same object
structure. If this is not the case, bad things will happen when the
SWIG wrappers cast between an object and any of its base classes. This
was not the case for NSGigE and Sinic devices. This patch makes NSGigE
and Sinic inherit from the new EtherDevBase class, which in turn
inherits from EtherDevice. As a bonus, this removes some duplicated
statistics from the Sinic device.
When casting objects in the generated SWIG interfaces, SWIG uses
classical C-style casts ( (Foo *)bar; ). In some cases, this can
degenerate into the equivalent of a reinterpret_cast (mainly if only a
forward declaration of the type is available). This usually works for
most compilers, but it is known to break if multiple inheritance is
used anywhere in the object hierarchy.
This patch introduces the cxx_header attribute to Python SimObject
definitions, which should be used to specify a header to include in
the SWIG interface. The header should include the declaration of the
wrapped object. We currently don't enforce header the use of the
header attribute, but a warning will be generated for objects that do
not use it.
This patch enables dumping statistics and Linux process information on
context switch boundaries (__switch_to() calls) that are used for
Streamline integration (a graphical statistics viewer from ARM).
This patch ensures cases like %0.6u, %06f, and %.6u are processed correctly.
The case like %06f is ambiguous and was made to match printf. Also, this patch
removes the goto statement in cprintf.cc in favor of a function call.
This patch adds a VncInput base class which VncServer inherits from.
Another class can implement the same interface and be used instead
of the VncServer, for example a class that replays Vnc traffic.
--HG--
rename : src/base/vnc/VncServer.py => src/base/vnc/Vnc.py
rename : src/base/vnc/vncserver.cc => src/base/vnc/vncinput.cc
rename : src/base/vnc/vncserver.hh => src/base/vnc/vncinput.hh
This patch takes the Linux thread info support scattered across
different ISA implementations (currently in ARM, ALPHA, and MIPS), and
unifies them into a single file.
Adds a few more helper functions to read out TGID, mm, etc.
ISA-specific information (e.g., ALPHA PCBB register) is now moved to
the corresponding isa_traits.hh files.
Changeset 4f54b0f229b5 removed the call to doDrain in changeToTiming
based on the assumption that the system does not need draining when
running in atomic mode. This is a false assumption since at least the
System class requires the system to be drained before it allows
switching of memory modes. This patch reverts that part of the
changeset.
This patch changes the default system clock from 1THz to 1GHz. This
clock is used by all modules that do not override the default (parent
clock), and primarily affects the IO subsystem. Every DMA device uses
its clock to schedule the next transfer, and the change will thus
cause this inter-transfer delay to be longer.
The default clock of the bus is removed, as the clock inherited from
the system provides exactly the same value.
A follow-on patch will bump the stats.
This patch simplifies the scheduling of the next walk for the ARM
table walker. Previously it used the CPU clock, but as the table
walker inherits the clock from the CPU, it is cleaner to simply use
its own clock (which is the same).
This patch removes the zero-time loop used to send items from the DMA
port transmit list. Instead of having a loop, the DMA port now uses an
event to schedule sending of a single packet.
Ultimately this patch serves to ease the transition to a blocking
4-phase handshake.
A follow-on patch will update the regression statistics.
I had forgotten to change the network test protocol while making changes to
ruby for supporting functional accesses. This patch updates the protocol so
that it can compile correctly.
This patch adds support to different entities in the ruby memory system
for more reliable functional read/write accesses. Only the simple network
has been augmented as of now. Later on Garnet will also support functional
accesses.
The patch adds functional access code to all the different types of messages
that protocols can send around. These messages are functionally accessed
by going through the buffers maintained by the network entities.
The patch also rectifies some of the bugs found in coherence protocols while
testing the patch.
With this patch applied, functional writes always succeed. But functional
reads can still fail.
The Memtest tester allows for only one request to be outstanding for a
particular physical address. The check has been written separately for
reads and writes. This patch moves the check earlier than its current
position so that it need not be written separately for reads and writes.
Currently the Ruby System maintains pointer to only one of the memory
controllers. But there can be multiple controllers in the system. This
patch adds a vector of memory controllers.
This patch adds support for function definitions to appear in slicc structs.
This is required for supporting functional accesses for different types of
messages. Subsequent patches will use this to development.
It seems unecessary that the BankedArray class needs to schedule an event
to figure out when the access ends. Instead only the time for the end of access
needs to be tracked.
Ruby system was recently converted to a clocked object. Such objects maintain
state related to the time that has passed so far. During the cache warmup, Ruby
system changes its own time and the global time. Later on, the global time is
restored. So Ruby system also needs to reset its own time.
This patch adds an additional level of ports in the inheritance
hierarchy, separating out the protocol-specific and protocl-agnostic
parts. All the functionality related to the binding of ports is now
confined to use BaseMaster/BaseSlavePorts, and all the
protocol-specific parts stay in the Master/SlavePort. In the future it
will be possible to add other protocol-specific implementations.
The functions used in the binding of ports, i.e. getMaster/SlavePort
now use the base classes, and the index parameter is updated to use
the PortID typedef with the symbolic InvalidPortID as the default.
This patch moves all the memory backing store operations from the
independent memory controllers to the global physical memory. The main
reason for this patch is to allow address striping in a future set of
patches, but at this point it already provides some useful
functionality in that it is now possible to change the number of
memory controllers and their address mapping in combination with
checkpointing. Thus, the host and guest view of the memory backing
store are now completely separate.
With this patch, the individual memory controllers are far simpler as
all responsibility for serializing/unserializing is moved to the
physical memory. Currently, the functionality is more or less moved
from AbstractMemory to PhysicalMemory without any major
changes. However, in a future patch the physical memory will also
resolve any ranges that are interleaved and properly assign the
backing store to the memory controllers, and keep the host memory as a
single contigous chunk per address range.
Functionality for future extensions which involve CPU virtualization
also enable the host to get pointers to the backing store.
This patch changes how the serialization of the system works. The base
class had a non-virtual serialize and unserialize, that was hidden by
a function with the same name for a number of subclasses (most likely
not intentional as the base class should have been virtual). A few of
the derived systems had no specialization at all (e.g. Power and x86
that simply called the System::serialize), but MIPS and Alpha adds
additional symbol table entries to the checkpoint.
Instead of overriding the virtual function, the additional entries are
now printed through a virtual function (un)serializeSymtab. The reason
for not calling System::serialize from the two related systems is that
a follow up patch will require the system to also serialize the
PhysicalMemory, and if this is done in the base class if ends up being
between the general parts and the specialized symbol table.
With this patch, the checkpoint is not modified, as the order of the
segments is unchanged.
This patch changes the data structure used to keep track of ports that
should be told to retry. As the bus is doing this in an FCFS way,
there is no point having a list. A deque is a better match (and is at
least in theory a better choice from a performance point of view).
This patch addresses a number of smaller issues identified by the code
inspection utility cppcheck. There are a number of identified leaks in
the arm/linux/system.cc (although the function only get's called once
so it is not a major problem), a few deletes in dev/x86/i8042.cc that
were not array deletes, and sprintfs where the character array had one
element less than needed. In the IIC tags there was a function
allocating an array of longs which is in fact never used.
This patch changes the cache-related latencies from an absolute time
expressed in Ticks, to a number of cycles that can be scaled with the
clock period of the caches. Ultimately this patch serves to enable
future work that involves dynamic frequency scaling. As an immediate
benefit it also makes it more convenient to specify cache performance
without implicitly assuming a specific CPU core operating frequency.
The stat blocked_cycles that actually counter in ticks is now updated
to count in cycles.
As the timing is now rounded to the clock edges of the cache, there
are some regressions that change. Plenty of them have very minor
changes, whereas some regressions with a short run-time are perturbed
quite significantly. A follow-on patch updates all the statistics for
the regressions.
This patch changes the CoherentBus between the L1s and L2 to use the
CPU clock and also four times the width compared to the default
bus. The parameters are not intending to fit every single scenario,
but rather serve as a better startingpoint than what we previously
had.
Note that the scripts that do not use the addTwoLevelCacheHiearchy are
not affected by this change.
A separate patch will update the stats.
This patch changes the default 1 Tick clock period to a proxy that
resolves the parents clock. As a result of this, the caches and
L1-to-L2 bus, for example, will automatically use the clock period of
the CPU unless explicitly overridden.
To ensure backwards compatibility, the System class overrides the
proxy and specifies a 1 Tick clock. We could change this to something
more reasonable in a follow-on patch, perhaps 1 GHz or something
similar.
With this patch applied, all clocked objects should have a reasonable
clock period set, and could start specifying delays in Cycles instead
of absolute time.
This patch modifies how proxies are traversed and unproxied to allow
chained proxies. The issue that is solved manifested itself when a
proxy during its evaluation ended up being hitting another proxy, and
the second one got evaluated using the object that was originally used
for the first proxy.
For a more tangible example, see the following patch on making the
default clock being inherited from the parent. In this patch, the CPU
clock is a proxy Parent.clock, which is overridden in the system to be
an actual value. This all works fine, but the AlphaLinuxSystem has a
boot_cpu_frequency parameter that is Self.cpu[0].clock.frequency. When
the latter is evaluated, it all happens relative to the current object
of the proxy, i.e. the system. Thus the cpu.clock is evaluated as
Parent.clock, but using the system rather than the cpu as the object
to enquire.
This patch transitions the bus to use the AddrRange operations instead
of directly accessing the start and end. The change facilitates the
move to a more elaborate AddrRange class that also supports address
striping in the bus by specifying interleaving bits in the ranges.
Two new functions are added to the AddrRange to determine if two
ranges intersect, and if one is a subset of another. The bus
propagation of address ranges is also tweaked such that an update is
only propagated if the bus received information from all the
downstream slave modules. This avoids the iteration and need for the
cycle-breaking scheme that was previously used.
This patch moves the block size computation from findBlockSize to
initialisation time, once all the neighbouring ports are connected.
There is no need to dynamically update the block size, and the caching
of the value effectively avoided that anyhow. This is very similar to
what was already in place, just with a slightly leaner implementation.
This patch bumps the Doxyfile to match more recent versions of
Doxygen. The sections that are deprecated have been removed, and the
new ones added. The project name has also been updated.
This patch removes the parts of slicc that were required for multi-chip
protocols. Going ahead, it seems multi-chip protocols would be implemented
by playing with the network itself.
This patch moves the code for functional accesses to ruby system. This is
because the subsequent patches add support for making functional accesses
to the messages in the interconnect. Making those accesses from the ruby port
would be cumbersome.
In the current caches the hit latency is paid twice on a miss. This patch lets
a configurable response latency be set of the cache for the backward path.
This patch adds a function, periodicStatDump(long long period), which will dump
and reset the statistics every period. This function is designed to be called
from the python configuration scripts. This allows the periodic stats dumping to
be configured more easilly at run time.
The period is currently specified as a long long as there are issues passing
Tick into the C++ from the python as they have conflicting definitions. If the
period is less than curTick, the first occurance occurs at curTick. If the
period is set to 0, then the event is descheduled and the stats are not
periodically dumped.
Due to issues when resumung from a checkpoint, the StatDump event must be moved
forward such that it occues AFTER the current tick. As the function is called
from the python, the event is scheduled before the system resumes from the
checkpoint. Therefore, the event is moved using the updateEvents() function.
This is called from simulate.py once the system has resumed from the checkpoint.
NOTE: It should be noted that this is a fairly temporary patch which re-adds the
capability to extract temporal information from the communication monitors. It
should not be used at the same time as anything that relies on dumping the
statistics based on in simulation events i.e. a context switch.
Newer Linux kernels require DTB (device tree blobs) to specify platform
configurations. The input DTB filename can be specified through gem5 parameters
in LinuxArmSystem.
Instead of statically defining miscRegName to contain NUM_MISCREGS
elements, let the compiler determine the length of the array. This
allows us to use a static_assert to test that all registers are listed
in the name vector.
C++11 has support for static_asserts to provide compile-time assertion
checking. This is very useful when testing, for example, structure
sizes to make sure that the compiler got the right alignment or vector
sizes.
Remove SimObject::setMemoryMode from the main SimObject class since it
is only valid for the System class. In addition to removing the method
from the C++ sources, this patch also removes getMemoryMode and
changeTiming from SimObject.py and updates the simulation code to call
the (get|set)MemoryMode method on the System object instead.
This patch adds an explicit dependency between param_%s.i and the
Python source file defining the object. Previously, the build system
didn't rebuild SWIG interfaces correctly when an object's Python
sources were updated.
Fix the drain functionality of the RubyPort to only call drain on child ports
during a system-wide drain process, instead of calling each time that a
ruby_hit_callback is executed.
This fixes the issue of the RubyPort ports being reawakened during the drain
simulation, possibly with work they didn't previously have to complete. If
they have new work, they may call process on the drain event that they had
not registered work for, causing an assertion failure when completing the
drain event.
Also, in RubyPort, set the drainEvent to NULL when there are no events
to be drained. If not set to NULL, the drain loop can result in stale
drainEvents used.
This patch introduces a high-level model of a DRAM controller, with a
basic read/write buffer structure, a selectable and customisable
arbiter, a few address mapping options, and the basic DRAM timing
constraints. The parameters make it possible to turn this model into
any desired DDRx/LPDDRx/WideIOx memory controller.
The intention is not to be cycle accurate or capture every aspect of a
DDR DRAM interface, but rather to enable exploring of the high-level
knobs with a good simulation speed. Thus, contrary to e.g. DRAMSim
this module emphasizes simulation speed with a good-enough accuracy.
This module is merely a starting point, and there are plenty additions
and improvements to come. A notable addition is the support for
address-striping in the bus to enable a multi-channel DRAM
controller. Also note that there are still a few "todo's" in the code
base that will be addressed as we go along.
A follow-up patch will add basic performance regressions that use the
traffic generator to exercise a few well-defined corner cases.
This patch adds a traffic generator to the code base. The generator is
aimed to be used as a black box model to create appropriate use-cases
and benchmarks for the memory system, and in particular the
interconnect and the memory controller.
The traffic generator is a master module, where the actual behaviour
is captured in a state-transition graph where each state generates
some sort of traffic. By constructing a graph it is possible to create
very elaborate scenarios from basic generators. Currencly the set of
generators include idling, linear address sweeps, random address
sequences and playback of traces (recording will be done by the
Communication Monitor in a follow-up patch). At the moment the graph
and the states are described in an ad-hoc line-based format, and in
the future this should be aligned with our used of e.g. the Google
protobufs. Similarly for the traces, the format is currently a
simplistic ad-hoc line-based format that merely serves as a starting
point.
In addition to being used as a black-box model for system components,
the traffic generator is also useful for creating test cases and
regressions for the interconnect and memory system. In future patches
we will use the traffic generator to create DRAM test cases for the
controller model.
The patch following this one adds a basic regressions which also
contains an example configuration script and trace file for playback.
This patch ignores the FUTEX_PRIVATE_FLAG of the sys_futex system call
in SE mode.
With this patch, when sys_futex with the options FUTEX_WAIT_PRIVATE or
FUTEX_WAKE_PRIVATE is emulated, the FUTEX_PRIVATE_FLAG is ignored and
so their behaviours are the regular FUTEX_WAIT and FUTEX_WAKE.
Emulating FUTEX_WAIT_PRIVATE and FUTEX_WAKE_PRIVATE as if they were
non-private is safe from a functional point of view. The
FUTEX_PRIVATE_FLAG does not change the semantics of the futex, it's
just a mechanism to improve performance under certain circunstances
that can be ignored in SE mode.
This patch removes the unused file parameter from the
AbstractMemory. The patch serves to make it easier to transition to a
separation of the actual contigious host memory backing store, and the
gem5 memory controllers.
Without the file parameter it becomes easier to hide the creation of
the mmap in the PhysicalMemory, as there are no longer any reasons to
expose the actual contigious ranges to the user.
To the best of my knowledge there is no use of the parameter, so the
change should not affect anyone.
This patch takes the final plunge and transitions from the templated
Range class to the more specific AddrRange. In doing so it changes the
obvious Range<Addr> to AddrRange, and also bumps the range_map to be
AddrRangeMap.
In addition to the obvious changes, including the removal of redundant
includes, this patch also does some house keeping in preparing for the
introduction of address interleaving support in the ranges. The Range
class is also stripped of all the functionality that is never used.
--HG--
rename : src/base/range.hh => src/base/addr_range.hh
rename : src/base/range_map.hh => src/base/addr_range_map.hh
This patch simplifies the Range class in preparation for the
introduction of a more specific AddrRange class that allows
interleaving/striping.
The only place where the parsing was used was in the unit test.
This patch simply removes the unused range_multimap in preparation for
a more specific AddrRangeMap that also allows interleaving in addition
to pure ranges.
This patch simplifies the Range object hierarchy in preparation for an
address range class that also allows striping (e.g. selecting a few
bits as matching in addition to the range).
To extend the AddrRange class to an AddrRegion, the first step is to
simplify the hierarchy such that we can make it as lean as possible
before adding the new functionality. The only class using Range and
MetaRange is AddrRange, and the three classes are now collapsed into
one.
This patch removes the use of g_system_ptr for event scheduling. Each consumer
object now needs to specify upfront an EventManager object it would use for
scheduling events. This makes the ruby memory system more amenable for a
multi-threaded simulation.
This patch makes a minor addition to the SimpleMemory by enforcing a
maximum data rate. The bandwidth is configurable, and a reasonable
value (12.8GB/s) has been choosen as the default.
The changes do add some complexity to the SimpleMemory, but they
should definitely be justifiable as this enables a far more realistic
setup using even this simple memory controller.
The rate regulation is done for reads and writes combined to reflect
the bidirectional data busses used by most (if not all) relevant
memories. Moreover, the regulation is done per packet as opposed to
long term, as it is the short term data rate (data bus width times
frequency) that is the limiting factor.
A follow-up patch bumps the stats for the regressions.
This patch adds Link-Time Optimization when building the fast target
using gcc >= 4.6, and adds a scons flag to disable it (-no-lto). No
check is performed to guarantee that the linker supports LTO and use
of the linker plugin, so the user has to ensure that binutils GNU ld
>= 2.21 or the gold linker is available. Typically, if gcc >= 4.6 is
available, the latter should not be a problem. Currently the LTO
option is only useful for gcc >= 4.6, due to the limited support on
clang and earlier versions of gcc. The intention is to also add
support for clang once the LTO integration matures.
The same number of jobs is used for the parallel phase of LTO as the
jobs specified on the scons command line, using the -flto=n flag that
was introduced with gcc 4.6. The gold linker also supports concurrent
and incremental linking, but this is not used at this point.
The compilation and linking time is increased by almost 50% on
average, although ARM seems to be particularly demanding with an
increase of almost 100%. Also beware when using this as gcc uses a
tremendous amount of memory and temp space in the process. You have
been warned.
After some careful consideration, and plenty discussions, the flag is
only added to the fast target, and the warning that was issued in an
earlier version of this patch is now removed. Similarly, the flag used
to enable LTO, now the default is to use it, and the flag has been
modified to disable LTO. The rationale behind this decision is that
opt is used for development, whereas fast is only used for long runs,
e.g. regressions or more elaborate experiments where the additional
compile and link time is amortized by a much larger run time.
When it comes to the return on investment, the regression seems to be
roughly 15% faster with LTO. For a bit more detail, I ran twolf on
ARM.fast, with three repeated runs, and they all finish within 42
minutes (+- 25 seconds) without LTO and 31 minutes (+- 25 seconds)
with LTO, i.e. LTO gives an impressive >25% speed-up for this case.
Without LTO (ARM.fast twolf)
real 42m37.632s
user 42m34.448s
sys 0m0.390s
real 41m51.793s
user 41m50.384s
sys 0m0.131s
real 41m45.491s
user 41m39.791s
sys 0m0.139s
With LTO (ARM.fast twolf)
real 30m33.588s
user 30m5.701s
sys 0m0.141s
real 31m27.791s
user 31m24.674s
sys 0m0.111s
real 31m25.500s
user 31m16.731s
sys 0m0.106s
This patch adds a new target called 'perf' that facilitates profiling
using google perftools rather than gprof. The perftools CPU profiler
offers plenty useful information in addition to gprof, and the latter
is kept mostly to offer profiling also on non-Linux hosts.
This patch restructures the ccflags such that the common parts are
defined in a single location, also capturing all the target types in a
single place.
The patch also adds a corresponding ldflags in preparation for
google-perf profiling support and the addition of Link-Time
Optimization.
This patch shifts the version of gcc for which we enable c++0x from
4.6 to 4.4 The more long term plan is to see what the c++0x features
can bring and what level of support would be enabled simply by bumping
the required version of gcc from 4.3 to 4.4.
A few minor things had to be fixed in the code base, most notably the
choice of a hashmap implementation. In the Ruby Sequencer there were
also a few minor issues that gcc 4.4 was not too happy about.
When switching from an atomic CPU to any of the timing CPUs, a drain is
unnecessary since no events are scheduled in atomic mode. However, when
trying to switch CPUs starting with a timing CPU, there may be events
scheduled. This change ensures that all events are drained from the system
by calling m5.drain before switching CPUs.
The profileEvent pointer is tested against NULL in various places, but
it is not initialized unless running in full-system mode. In SE mode, this
can result in segmentation faults when profileEvent default intializes to
something other than NULL.
This patch addresses a few minor issues reported by the clang static
analyzer.
The analysis was run with:
scan-build -disable-checker deadcode \
-enable-checker experimental.core \
-disable-checker experimental.core.CastToStruct \
-enable-checker experimental.cpluscplus
This seperates the functionality to clear the state in a block into
blk.hh and the functionality to udpate the tag information into the
tags. This gets rid of the case where calling invalidateBlk on an
already-invalid block does something different than calling it on a
valid block, which was confusing.
The patch introduces two predicates for condition code registers -- one
tests if a register needs to be read, the other tests whether a register
needs to be written to. These predicates are evaluated twice -- during
construction of the microop and during its execution. Register reads
and writes are elided depending on how the predicates evaluate.
The D flag bit is part of the cc flag bit register currently. But since it
is not being used any where in the implementation, it creates an unnecessary
dependency. Hence, it is being moved to a separate register.
This patch is meant for allowing predicated reads and writes. Note that this
predication is different from the ISA provided predication. They way we
currently provide the ISA description for X86, we read/write registers that
do not need to be actually read/written. This is likely to be true for other
ISAs as well. This patch allows for read and write predicates to be associated
with operands. It allows for the register indices for source and destination
registers to be decided at the time when the microop is constructed. The
run time indicies come in to play only when the at least one of the
predicates has been provided. This patch will not affect any of the ISAs that
do not provide these predicates. Also the patch assumes that the order in
which operands appear in any function of the microop is same across all the
functions of the microops. A subsequent patch will enable predication for the
x86 ISA.
If I understand correctly, this was put in place so that a debugger can be
attached when the protocol aborts. While this sounds useful, it is a problem
when the simulation is not being actively monitored. I think it is better to
remove this.
Despite gzwrite taking an unsigned for length, it returns an int for
bytes written; gzwrite fails if (int)len < 0. Because of this, call
gzwrite with len no larger than INT_MAX: write in blocks of INT_MAX if
data to be written is larger than INT_MAX.
This patch prunes the range_ops header that is no longer used. The
bridge used it to do filtering of address ranges, but this is changed
since quite some time.
Ultimately this patch aims to simplify the handling of ranges before
specialising the AddrRange to an AddrRegion that also allows striping
bits to be selected.
This patch aims to simplify the use of the Range class before
introducing a more elaborate AddrRegion to replace the AddrRange. The
SackRange is the only use of the range class besides address ranges,
and the removal of this use makes for an easier modification of the
range class.
The functionlity that is removed with this patch is not used anywhere
throughout the code base.
This patch addresses a previously highlighted issue with the default
latencies used for PIO and PCI devices. The values are merely educated
guesses and might not represent the particular system you want to
model. However, the values in this patch are definitely far more
realistic than the previous ones.
In i8254xGBe, the writeConfig method is updated to use configDelay
instead of pioDelay.
A follow-up patch will update the regression stats.
Includes a small change in sim_object.cc that adds the name space to
the output stream parameter in serializeAll. Leaving out the name
space unfortunately confuses Doxygen.
Simulation objects normally register derived statistics, presumably
what regFormulas originally was meant for, in regStats(). This patch
removes regRegformulas since there is no need to have a separate
method call to register formulas.
Implement some code we used to panic on as it actually does happen with the
e1000 driver in Linux 3.3+. We used to assume that a TSO header would never
be part of a larger payload, however it appears as though it now can be.
Some bare metal build flows seem to build binaries that we aren't necessarily
expecting. Initialize everything to 0, so we don't make any assumptions about
what is or isn't in the binary.
This patch is a first step to using Cycles as a parameter type. The
main affected modules are the CPUs and the Ruby caches. There are
definitely plenty more places that are affected, but this patch serves
as a starting point to making the transition.
An important part of this patch is to actually enable parameters to be
specified as Param.Cycles which involves some changes to params.py.
The =operator for the DataBlock class was incorrectly interpreting the class
member m_alloc. This variable stands for whether the assigned memory for the
data block needs to be freed or not by the class itself. It seems that the
=operator interpreted the variable as whether the memory is assigned to the
data block. This wrong interpretation was causing values not to propagate
to RubySystem::m_mem_vec_ptr. This caused major issues with restoring from
checkpoints when using a protocol which verified that the cache data was
consistent with the backing store (i.e. MOESI-hammer).
This patch addresses the comments and feedback on the preceding patch
that reworks the clocks and now more clearly shows where cycles
(relative cycle counts) are used to express time.
Instead of bumping the existing patch I chose to make this a separate
patch, merely to try and focus the discussion around a smaller set of
changes. The two patches will be pushed together though.
This changes done as part of this patch are mostly following directly
from the introduction of the wrapper class, and change enough code to
make things compile and run again. There are definitely more places
where int/uint/Tick is still used to represent cycles, and it will
take some time to chase them all down. Similarly, a lot of parameters
should be changed from Param.Tick and Param.Unsigned to
Param.Cycles.
In addition, the use of curTick is questionable as there should not be
an absolute cycle. Potential solutions can be built on top of this
patch. There is a similar situation in the o3 CPU where
lastRunningCycle is currently counting in Cycles, and is still an
absolute time. More discussion to be had in other words.
An additional change that would be appropriate in the future is to
perform a similar wrapping of Tick and probably also introduce a
Ticks class along with suitable operators for all these classes.
This patch introduces the notion of a clock update function that aims
to avoid costly divisions when turning the current tick into a
cycle. Each clocked object advances a private (hidden) cycle member
and a tick member and uses these to implement functions for getting
the tick of the next cycle, or the tick of a cycle some time in the
future.
In the different modules using the clocks, changes are made to avoid
counting in ticks only to later translate to cycles. There are a few
oddities in how the O3 and inorder CPU count idle cycles, as seen by a
few locations where a cycle is subtracted in the calculation. This is
done such that the regression does not change any stats, but should be
revisited in a future patch.
Another, much needed, change that is not done as part of this patch is
to introduce a new typedef uint64_t Cycle to be able to at least hint
at the unit of the variables counting Ticks vs Cycles. This will be
done as a follow-up patch.
As an additional follow up, the thread context still uses ticks for
the book keeping of last activate and last suspend and this should
probably also be changed into cycles as well.
This patch tightens up the semantics around port binding and checks
that the ports that are being bound are currently not connected, and
similarly connected before unbind is called.
The patch consequently also changes the order of the unbind and bind
for the switching of CPUs to ensure that the rules are adhered
to. Previously the ports would be "over-written" without any check.
There are no changes in behaviour due to this patch, and the only
place where the unbind functionality is used is in the CPU.
This patch updates how the checker CPU handles the ports such that the
regressions will once again run without causing a panic.
A minor amount of tidying up was also done as part of this patch.
This patch disables a warning for unused values which causes problems
when compiling the swig-generated sources using recent llvm-based
compilers like llvm-gcc and clang.
The memory size variable was a 32-bit int. This meant that the size of the
memory was limited to 4GB. This patch changes the type of the variable to
64-bit to support larger memory sizes. Thanks to Raghuraman Balasubramanian
for bringing this to notice.
This patch does a bunch of house-keeping updates on the DMA, including
indentation, and formatting, but most importantly breaks out the
response handling such that it can be shared between the atomic and
timing modes. It also removes a potential bug caused by the atomic
handling of responses only deleting the allocated request (pkt->req)
once the DMA action completes instead of doing so for every packet.
Before this patch, the handling of responses was near identical for
atomic and timing, but the code was simply duplicated. With this
patch, the handleResp method deals with the responses in both cases.
There are further updates to make after removing the NACKs, but that
will be part of a separate follow-up patch. This patch does not change
the behaviour of any regression.
This patch removes the NACK frrom the packet as there is no longer any
module in the system that issues them (the bridge was the only one and
the previous patch removes that).
The handling of NACKs was mostly avoided throughout the code base, by
using e.g. panic or assert false, but in a few locations the NACKs
were actually dealt with (although NACKs never occured in any of the
regressions). Most notably, the DMA port will now never receive a NACK
and the backoff time is thus never changed. As a consequence, the
entire backoff mechanism (similar to a PCI bus) is now removed and the
DMA port entirely relies on the bus performing the arbitration and
issuing a retry when appropriate. This is more in line with e.g. PCIe.
Surprisingly, this patch has no impact on any of the regressions. As
mentioned in the patch that removes the NACK from the bridge, a
follow-up patch should change the request and response buffer size for
at least one regression to also verify that the system behaves as
expected when the bridge fills up.
This patch removes the NACKing in the bridge, as the split
request/response busses now ensure that protocol deadlocks do not
occur, i.e. the message-dependency chain is broken by always allowing
responses to make progress without being stalled by requests. The
NACKs had limited support in the system with most components ignoring
their use (with a suitable call to panic), and as the NACKs are no
longer needed to avoid protocol deadlocks, the cleanest way is to
simply remove them.
The bridge is the starting point as this is the only place where the
NACKs are created. A follow-up patch will remove the code that deals
with NACKs in the endpoints, e.g. the X86 table walker and DMA
port. Ultimately the type of packet can be complete removed (until
someone sees a need for modelling more complex protocols, which can
now be done in parts of the system since the port and interface is
split).
As a consequence of the NACK removal, the bridge now has to send a
retry to a master if the request or response queue was full on the
first attempt. This change also makes the bridge ports very similar to
QueuedPorts, and a later patch will change the bridge to use these. A
first step in this direction is taken by aligning the name of the
member functions, as done by this patch.
A bit of tidying up has also been done as part of the simplifications.
Surprisingly, this patch has no impact on any of the
regressions. Hence, there was never any NACKs issued. In a follow-up
patch I would suggest changing the size of the bridge buffers set in
FSConfig.py to also test the situation where the bridge fills up.
This patch extends the queued port interfaces with methods for
scheduling the transmission of a timing request/response. The methods
are named similar to the corresponding sendTiming(Snoop)Req/Resp,
replacing the "send" with "sched". As the queues are currently
unbounded, the methods always succeed and hence do not return a value.
This functionality was previously provided in the subclasses by
calling PacketQueue::schedSendTiming with the appropriate
parameters. With this change, there is no need to introduce these
extra methods in the subclasses, and the use of the queued interface
is more uniform and explicit.
This patch removes the overloading of the parameter, which seems both
redundant, and possibly incorrect.
The PciConfigAll now also uses a Param.Latency rather than a
Param.Tick. For backwards compatibility it still sets the pio_latency
to 1 tick. All the comments have also been updated to not state that
it is in simticks when it is not necessarily the case.
This patch removes the overloading of the parameter, which seems both
redundant, and possibly incorrect.
The inorder CPU is particularly interesting as it uses a different
name for the parameter, and never make any use of it internally.
This patch allows packets to be enqueued in the same tick as they are
intended to be sent. This does not imply they actually are sent that
tick, although that is possible.
This change is useful for module that use the queued ports primarly to
avoid handling the flow control involved in sending and retrying
packets.
This patch tidies up the EventManager constructor and prunes a corner
case where the EventManager would initialise its eventq pointer to
NULL. This would cause segmentation faults on actual use and should
never happen.
This patch makes the Tick unsigned and removes the UTick typedef. The
ticks should never be negative, and there was only one major issue
with removing it, caused by the o3 CPU using a -1 as an initial value.
The patch has no impact on any regressions.
This patch moves the clock of the CPU, bus, and numerous devices to
the new class ClockedObject, that sits in between the SimObject and
MemObject in the class hierarchy. Although there are currently a fair
amount of MemObjects that do not make use of the clock, they
potentially should do so, e.g. the caches should at some point have
the same clock as the CPU, potentially with a 1:n ratio. This patch
does not introduce any new clock objects or object hierarchies
(clusters, clock domains etc), but is still a step in the direction of
having a more structured approach clock domains.
The most contentious part of this patch is the serialisation of clocks
that some of the modules (but not all) did previously. This
serialisation should not be needed as the clock is set through the
parameters even when restoring from the checkpoint. In other words,
the state is "stored" in the Python code that creates the modules.
The nextCycle methods are also simplified and the clock phase
parameter of the CPU is removed (this could be part of a clock object
once they are introduced).
Alpha System was overriding loadState() function to setup some functional
event. The system tried to read/write to memory before the Ruby memory had
unserialized the state. With this patch, Alpha System overrides the
startup() function, and sets up functional events in this function. This
works because startup() is called after Ruby memory system has unserialized
the memory state.
This patch fixes some problems with the drain/switchout functionality
for the O3 cpu and for the ARM ISA and adds some useful debug print
statements.
This is an incremental fix as there are still a few bugs/mem leaks with the
switchout code. Particularly when switching from an O3CPU to a
TimingSimpleCPU. However, when switching from O3 to O3 cores with the ARM ISA
I haven't encountered any more assertion failures; now the kernel will
typically panic inside of simulation.
New tool chains seem to be looking for kernel versions newer than what
this this was previously set to. Also take this opportunity to change
the hostname we report in uname to sim.gem5.org.
This patch moves instantiateTopology into Ruby.py and removes the
mem/ruby/network/topologies directory. It also adds some extra inheritance to
the topologies to clean up some issues in the existing topologies.
Off-by-one loop termination meant that we were stuffing
the terminating '\0' into the std::string value, which
makes for difficult-to-debug string comparison failures.
This replaces a (potentially uninitialized) string
field with a virtual function so that we can have
a safe interface without requiring changes to the
eio code.
Enable different whitelists for different OS/arch combinations,
since some use the generic Linux definitions only, and others
use definitions inherited from earlier Unix flavors on those
architectures.
Also update x86 function pointers so ioctl is no longer
unimplemented on that platform.
This patch is a revised version of Vince Weaver's earlier patch.
when using the checker i ran into problems where an instruction reading the
cpu id register failed because the ids did not match, and hence, the result
of the instruction did not match. this patch ensures that the ids match so
this instruction does not fail. this problem only seemed to manifest itself
when multiple cores were in the system, either multi-core, or extra switched-
out cores present in the system.
removes the optimization that forwards an exclusive copy to a requester on a
read, only for the i-cache. this optimization isn't necessary because we
typically won't be writing to the i-cache.
According to the A15 TRM the value of this register is as follows (assuming 16 word = 64 byte lines)
[31:29] Format - b100 specifies v7
[28] RAZ - b0
[27:24] CWG log2(max writeback size #words) - 0x4 16 words
[23:20] ERG log2(max reservation size #words) - 0x4 16 words
[19:16] DminLine log2(smallest dcache line #words) - 0x4 16 words
[15:14] L1Ip L1 index/tagging policy - b11 specifies PIPT
[13:4] RAZ - b0000000000
[3:0] IminLine log2(smallest icache line #words) - 0x4 16 words
This patch changes the simple memory to have a single slave port
rather than a vector port. The simple memory makes no attempts at
modelling the contention between multiple ports, and any such
multiplexing and demultiplexing could be done in a bus (or crossbar)
outside the memory controller. This scenario also matches with the
ongoing work on a SimpleDRAM model, which will be a single-ported
single-channel controller that can be used in conjunction with a bus
(or crossbar) to create a multi-port multi-channel controller.
There are only very few regressions that make use of the vector port,
and these are all for functional accesses only. To facilitate these
cases, memtest and memtest-ruby have been updated to also have a
"functional" bus to perform the (de)multiplexing of the functional
memory accesses.
This patch removes printConfig() functions from all structures in Ruby.
Most of the information is already part of config.ini, and where ever it
is not, it would become in due course.
This enables configuration scripts to set up mappings
from process virtual addresses to specific physical
addresses in SE mode. This feature is needed to
support modeling of user-accessible memories or
devices in SE mode, avoiding the complexities of FS
mode and the need to write a device driver.
This patch models a cache as separate tag and data arrays. The patch exposes
the banked array as another resource that is checked by SLICC before a
transition is allowed to execute. This is similar to how TBE entries and slots
in output ports are modeled.
Updates to Ruby to support statistics counting of cache accesses. This feature
serves multiple purposes beyond simple stats collection. It provides the
foundation for ruby to model the cache tag and data arrays as physical
resources, as well as provide the necessary input data for McPAT power
modeling.
Instead of just passing a list of controllers to the makeTopology function
in src/mem/ruby/network/topologies/<Topo>.py we pass in a function pointer
which knows how to make the topology, possibly with some extra state set
in the configs/ruby/<protocol>.py file. Thus, we can move all of the files
from network/topologies to configs/topologies. A new class BaseTopology
is added which all topologies in configs/topologies must inheirit from and
follow its API.
--HG--
rename : src/mem/ruby/network/topologies/Crossbar.py => configs/topologies/Crossbar.py
rename : src/mem/ruby/network/topologies/Mesh.py => configs/topologies/Mesh.py
rename : src/mem/ruby/network/topologies/MeshDirCorners.py => configs/topologies/MeshDirCorners.py
rename : src/mem/ruby/network/topologies/Pt2Pt.py => configs/topologies/Pt2Pt.py
rename : src/mem/ruby/network/topologies/Torus.py => configs/topologies/Torus.py
This patch renames the queue() accessor to the less ambigious
eventQueue, and also removes the cast operator. The queue() member
function cause problems in derived classes that declare members with
the same name, e.g. a MemObject subclass that has a packet queue on
its own. The operator is not causing any harm at this point, but as it
is not used there is little point in keeping it.
This patch makes the queue implementation in the SimpleTimingPort
private to avoid confusion with the protected member queue in the
QueuedSlavePort. The SimpleTimingPort provides the queue_impl to the
QueuedSlavePort and it can be accessed via the reference in the base
class. The use of the member name queue is thus no longer overloaded.
This patch is a first step to align the port names used in the Python
world and the C++ world. Ultimately it serves to make the use of
config.json together with output from the simulation easier, including
post-processing of statistics.
Most notably, the CPU, cache, and bus is addressed in this patch, and
there might be other ports that should be updated accordingly. The
dash name separator has also been replaced with a "." which is what is
used to concatenate the names in python, and a separation is made
between the master and slave port in the bus.
This patch changes the default bus width to a more sensible 8 bytes
(64 bits), which is in line with most on-chip buses. Although there
are cases where a wider or narrower bus is useful, the 8 bytes is a
good compromise to serve as the default.
This patch changes essentially all statistics, and will be bundled
with the outstanding changes to the bus.
This patch splits the existing buses into multiple layers. The
non-coherent bus is split into a request and a response layer, and the
coherent bus adds an additional layer for the snoop responses. The
layer is modified to be templatised on the port type, such that the
different layers can have retryLists with either master or slave
ports. This patch also removes the dynamic cast from the retry, as
previously promised when moving the recvRetry from the port base class
to the master/slave port respectively.
Overall, the split bus more closely reflects any modern on-chip bus
and should be at step in the right direction. From this point, it
would be reasonable straight forward to add separate layers (and thus
contention points and arbitration) for each port and thus create a
true crossbar.
The regressions all produce the correct output, but have varying
degrees of changes to their statistics. A separate patch will be
pushed with the updates to the reference statistics.
This patch moves all flow control, arbitration and state information
into a bus layer. The layer is thus responsible for all the state
transitions, and for keeping hold of the retry list. Consequently the
layer is also responsible for the draining.
With this change, the non-coherent and coherent bus are given a single
layer to avoid changing any temporal behaviour, but the patch opens up
for adding more layers.
This patch adds a state enum and member variable in the bus, tracking
the bus state, thus eliminating the need for tickNextIdle and inRetry,
and fixing an issue that allowed the bus to be occupied by multiple
packets at once (hopefully it also makes it easier to understand the
code).
The bus, in its current form, uses tickNextIdle and inRetry to keep
track of the state of the bus. However, it only updates tickNextIdle
_after_ forwarding a packet using sendTiming, and the result is that
the bus is still seen as idle, and a module that receives the packet
and starts transmitting new packets in zero time will still see the
bus as idle (and this is done by a number of DMA devices). The issue
can also be seen in isOccupied where the bus calls reschedule on an
event instead of schedule.
This patch addresses the problem by marking the bus as _not_ idle
already by the time we conclude that the bus is not occupied and we
will deal with the packet.
As a result of not allowing multiple packets to occupy the bus, some
regressions have slight changes in their statistics. A separate patch
updates these accordingly.
Further ahead, a follow-on patch will introduce a separate state
variable for request/responses/snoop responses, and thus implement a
split request/response bus with separate flow control for the
different message types (even further ahead it will introduce a
multi-layer bus).
This patch makes getAddrRanges const throughout the code base. There
is no reason why it should not be, and making it const prevents adding
any unintentional side-effects.
This patch adds getAddrRanges to the master port, and thus avoids
going through getSlavePort to be able to ask the slave. Similar to the
previous patch that added isSnooping to the SlavePort, this patch aims
to introduce an additional level of hierarchy in the ports (base port
being protocol-agnostic) and getSlave/MasterPort will return port
pointers to these base classes.
The function is named getAddrRanges also on the master port, but does
nothing besides asking the connected slave port. The slave port, as
before, has to provide an implementation and actually produce a list
of address ranges. The initial design used the name getSlaveAddrRanges
for the new function, but the more verbose name was later changed.
This patch adds isSnooping to the slave port, and thus avoids going
through getMasterPort to be able to ask the master. Over the course of
the next few patches, all getMasterPort/getSlavePort in Port and
MemObject are to be protocol agnostic, and the snooping is part of the
protocol layer.
The function is already present on the master port, where it is
implemented by the module itself, e.g. a cache. On the slave side, it
is merely asking the connected master port. The same name is used by
both functions despite their difference in behaviour. The initial
design used isMasterSnooping on the slave port side, but the more
verbose function name was later changed.
This patch is the last part of moving all protocol-related
functionality out of the Port base class. All the send/recv functions
are already moved, and the retry (which still governs all the timing
transport functions) is the only part that remained in the base class.
The only point where this currently causes a bit of inconvenience is
in the bus where the retry list is global and holds Port pointers (not
Master/SlavePort). This is about to change with the split into a
request/response bus and will soon be removed anyway.
The patch has no impact on any regressions.
This patch is the result of static analysis identifying a number of
memory leaks. The leaks are all benign as they are a result of not
deallocating memory in the desctructor. The fix still has value as it
removes false positives in the static analysis.
This patch fixes two warnings, one related to a narrowing conversion
(int to MachInst), and one due to the cast operator for arguments and
a mismatch in const-ness (const void* and void*).
The LRU policy always evicted the least recently touched way, even if it
contained valid data and another way was invalid, as can happen if a block has
been invalidated by coherance. This can result in caches never warming up even
though they are replacing blocks. This modifies the LRU policy to move blocks
to LRU position on invalidation.
Currently when multiple CPUs perform a load-linked/store-conditional sequence,
the loads all create a list of reservations which is then scanned when the
stores occur. A reservation matching the context and address of the store is
sought, BUT all reservations matching the address are also erased at this point.
The upshot is that a store-conditional will remove all reservations even if the
store itself does not succeed. A livelock was observed using 7-8 CPUs where a
thread would erase the reservations of other threads, not succeed, loop and put
its own reservation in again only to have it blown by another thread that
unsuccessfully now tries to store-conditional -- no forward progress was made,
hanging the system.
The correct way to do this is to only blow a reservation when a store
(conditional or not) actually /occurs/ to its address. One thread always wins
(the one that does the store-conditional first).
Add new flag (named pushedRAS) in the PredictorHistory structure.
This flag tracks whether the RAS has been pushed or not during a prediction.
Then, in the squash function it is used to pop the RAS if necessary.
npc in PCState for ARM was being calculated before the current flags were
updated with the next flags. This causes an issue as the npc is incremented by
two or four depending on the current flags (thumb or not) and was leading to
branches that were predicted correctly being identified as mispredicted.
This patch fixes a failing compilation caused by MaxMiscDestRegs being
zero. According to gcc 4.6, the result is a comparison that is always
false due to limited range of data type.
This patch is a temporary fix until Andreas' four-phase patches
get reviewed and committed. Removing FastAlloc seems to have exposed
an issue which previously was reasonable rare in which packets are freed
before the sending cache is done with them. This change puts incoming packets
no a pendingDelete queue which are deleted at the start of the next call and
thus breaks the dependency between when the caller returns true and when the
packet is actually used by the sending cache.
Running valgrind on a multi-core linux boot and the memtester results in no
valgrind warnings.
Due to recent changes to X86 TLB, gem5 stopped compiling on
gcc version 4.4.3. This patch provides the fix for that problem. The patch
is tested on gcc 4.4.3. The change is not required for more recent
versions of gcc (like on 4.6.3).
initCPU() will be called to initialize switched out CPUs for the simple and
inorder CPU models. this patch prevents those CPUs from being initialized
because they should get their state from the active CPU when it is switched
out.
This change allows designating a system as MP capable or not as some
bootloaders/kernels care that it's set right. You can have a single
processor MP capable system, but you can't have a multi-processor
UP only system. This change also fixes the initialization of the MIDR
register.
While FastAlloc provides a small performance increase (~1.5%) over regular malloc it isn't thread safe.
After removing FastAlloc and using tcmalloc I've seen a performance increase of 12% over libc malloc
when running twolf for ARM.
The CPUID instruction was implemented so that it would only write its results
if the instruction was successful. This works fine on the simple CPU where
unwritten registers retain their old values, but on a CPU like O3 with
renaming this is broken. The instruction needs to write the old values back
into the registers explicitly if they aren't being changed.
There are some bits of some fields of the ExtMachInst which are not actually
used for anything but are included in the hash of an ExtMachInst for
simplicity and efficiency. This change makes sure the decoder's internal
working ExtMachInst is completely initialized, even these unused bits, so that
there isn't any nondeterministic behavior, no valgrind messages about
uninitialized variables, and no potential false misses/redundant entries in
the decode cache.
This patch introduces a class hierarchy of buses, a non-coherent one,
and a coherent one, splitting the existing bus functionality. By doing
so it also enables further specialisation of the two types of buses.
A non-coherent bus connects a number of non-snooping masters and
slaves, and routes the request and response packets based on the
address. The request packets issued by the master connected to a
non-coherent bus could still snoop in caches attached to a coherent
bus, as is the case with the I/O bus and memory bus in most system
configurations. No snoops will, however, reach any master on the
non-coherent bus itself. The non-coherent bus can be used as a
template for modelling PCI, PCIe, and non-coherent AMBA and OCP buses,
and is typically used for the I/O buses.
A coherent bus connects a number of (potentially) snooping masters and
slaves, and routes the request and response packets based on the
address, and also forwards all requests to the snoopers and deals with
the snoop responses. The coherent bus can be used as a template for
modelling QPI, HyperTransport, ACE and coherent OCP buses, and is
typically used for the L1-to-L2 buses and as the main system
interconnect.
The configuration scripts are updated to use a NoncoherentBus for all
peripheral and I/O buses.
A bit of minor tidying up has also been done.
--HG--
rename : src/mem/bus.cc => src/mem/coherent_bus.cc
rename : src/mem/bus.hh => src/mem/coherent_bus.hh
rename : src/mem/bus.cc => src/mem/noncoherent_bus.cc
rename : src/mem/bus.hh => src/mem/noncoherent_bus.hh
This patch makes two very minor changes to please gcc 4.7. The
CopyData function no longer exists and this has been replaced. For
some reason previous versions of gcc did not complain on the const
char casting not having an implementation, but this is now addressed.
This patch merely remove the Packet* from the isOccupied member
function. Historically this was used to check if the packet was an
express snoop, but this is now done outside this function (where
relevant).
The main aim of this patch is to arrive at a suitable port interface
for vector ports, including both the packet and the port id. This
patch changes the bus transport functions
(recvFunctional/Atomic/Timing) to require a PortId parameter
indicating the source port. Previously this information was passed by
setting the source field of the packet, and this is only required in
the case of a timing request.
With this patch, the use of the source and destination field is also
more restrictive, as they are only needed for timing accesses. The
modifications to these fields for atomic snoops is now removed
entirely, also making minor modifications to the cache.
This patch removes the Packet::NodeID typedef and unifies it with the
Port::PortId. The src and dest fields in the packet are used to hold a
port id (e.g. in the bus), and thus the two should actually be the
same.
The typedef PortID is now global (in base/types.hh) and aligned with
the ThreadID in terms of capitalisation and naming of the
InvalidPortID constant.
Before this patch, two flags were used for valid destination and
source, rather than relying on a named value (InvalidPortID), and
this is now redundant, as the src and dest field themselves are
sufficient to tell whether the current value is a valid port
identifier or not. Consequently, the VALID_SRC and VALID_DST are
removed.
As part of the cleaning up, a number of int parameters and local
variables are updated to use PortID.
Note that Ruby still has its own NodeID typedef. Furthermore, the
MemObject getMaster/SlavePort still has an int idx parameter with a
default value of -1 which should eventually change to PortID idx =
InvalidPortID.
This patch updates the comments for the src and dest fields to reflect
their actual use. Due to a number of patches (e.g. removing the
Broadcast flag), the old comments are no longer indicative of the
current usage.
This patch splits the PacketBuffer class into a RequestState and a
DeferredRequest and DeferredResponse. Only the requests need a
SenderState, and the deferred requests and responses only need an
associated point in time for the request and the response queue.
Besides the cleaning up, the goal is to simplify the transition to a
new port handshake, and with these changes, the two packet queues are
starting to look very similar to the generic packet queue, but
currently they do a few unique things relating to the NACK and
counting of requests/responses that the packet queue cannot be
conveniently used. This will be addressed in a later patch.
The GDT can be accessed by user level software running in compatibility mode
by moving segment selectors into segment registers. The GDT needs to be set up
at an address accessible in this mode.
A small change was added a while ago to keep addresses from overflowing 32
bits when larger addresses shouldn't be accessible to software. That change
truncated when not in long mode, but really it should have truncated when not
in 64 bit mode. The difference is whether compatibility mode is included, a
mode that's supposed to act like a legacy 32 bit mode.
This will allow it to be specialized by the ISAs. The existing caching scheme
is provided by the BasicDecodeCache in the GenericISA namespace and is built
from the generalized components.
--HG--
rename : src/cpu/decode_cache.cc => src/arch/generic/decode_cache.cc
These classes are always used together, and merging them will give the ISAs
more flexibility in how they cache things and manage the process.
--HG--
rename : src/arch/x86/predecoder_tables.cc => src/arch/x86/decoder_tables.cc
This patch removes unused commands and attributes from the packet to
avoid any confusion. It is part of an effort to clear up how and where
different commands and attributes are used.
This patch changes the organisation of the JSON output slightly to
make it easier to traverse and use the files. Most importantly, the
hierarchical dictionaries now use keys that correspond to the
attribute names also in the case of VectorParams (used to be
e.f. "cpu0 cpu1"). It also adds the name and the path to each
SimObject directory entry. Before this patch, to get cpu0, you would
have to query dict['system']['cpu0 cpu1'][0] and this could be a dict
with 'cpu0' : { cpu parameters }. Now you use dict['system']['cpu'][0]
and get { cpu parameters } (where one is "name" : "cpu0").
Additionally this patch includes more verbose information about the
ports, specifying their role, and using a JSON array rather than a
concatenated string for the peer.
This patch moves the DMA device to its own set of files, splitting it
from the IO device. There are no behavioural changes associated with
this patch.
The patch also grabs the opportunity to do some very minor tidying up,
including some white space removal and pruning some redundant
parameters.
Besides the immediate benefits of the separation-of-concerns, this
patch also makes upcoming changes more streamlined as it split the
devices that are only slaves and the DMA device that also acts as a
master.
--HG--
rename : src/dev/io_device.cc => src/dev/dma_device.cc
rename : src/dev/io_device.hh => src/dev/dma_device.hh
This patch makes the (device) DmaPort non-snooping and removes the
recvSnoop constructor parameter and instead introduces a
SnoopingDmaPort subclass for the ARM table walker.
Functionality is unchanged, as are the stats, and the patch merely
clarifies that the normal DMA ports are not snooping (although they
may issue requests that are snooped by others, as done with PCI, PCIe,
AMBA4 ACE etc).
Currently this port is declared in the ARM table walker as it is not
used anywhere else. If other ports were to have similar behaviour it
could be moved in a future patch.
This patch turns the existing warning into a fatal, as there should
never be any cases where a (non-vector) port is assigned to and then
later connected to something else. If this behaviour is allowed, as it
used to be, there are cases where the wrong number of C++ ports are
created when instantiating objects with VectorPorts (obviously that
could be fixed, but the better approach is to simply not allow it).
The scheduling of the deadlock check event was being done incorrectly as the
clock was not being multiplied, so as to convert the time into ticks. This
patch removes that bug.
This patch moves the ECF and EZF bits to individual registers (ecfBit and
ezfBit) and the CF and OF bits to cfofFlag registers. This is being done
so as to lower the read after write dependencies on the the condition code
register. Ultimately we will have the following registers [ZAPS], [OF],
[CF], [ECF], [EZF] and [DF]. Note that this is only one part of the
solution for lowering the dependencies. The other part will check whether
or not the condition code register needs to be actually read. This would
be done through a separate patch.
If the length argument to mmap is larger than the arbitrary but reasonable
limit of 4GB, there's a good chance that the value is nonsense and not
intentional. Rather than attempting to satisfy the mmap anyway, this change
makes gem5 warn to make it more apparent what's going wrong.
Revised system visualization to reflect structure and memory hierarchy.
Improved visualization: less congested and cluttered; more colorful.
Nodes reflect components; directed edges reflect dirctional relation, from
a master port to a slave port. Requires pydot.
Fixed broken code which visualizes the system configuration by generating a
tree from each component's children, starting from root.
Requires DOT (hence pydot).
Symbol tables masked with the loadAddrMask create redundant entries
that could conflict with kernel function events that rely on the
original addresses. This patch guards the creation of those masked
symbol tables by default, with an option to enable them when needed
(for early-stage kernel debugging, etc.)
Track the point in the initialization where statistics have been registered.
After this point registering new masterIds can no longer work as some
SimObjects may have sized stats vectors based on the previous value. If someone
tries to register a masterId after this point the simulator executes fatal().
An older revision of the data sheet specified that txdctl.gran was 1 the granularity was
based on cache block and gran being 0 is based on descriptor count. The newer version of
the data sheet reverses this errata
This patch adds a communication monitor MemObject that can be inserted
between a master and slave port to provide a range of statistics about
the communication passing through it. The communication monitor is
non-invasive and does not change any properties or timing of the
packets, with the exception of adding a sender state to be able to
track latency. The statistics are only collected in timing mode (not
atomic) to avoid slowing down any fast forwarding.
An example of the statistics captured by the monitor are: read/write
burst lengths, bandwidth, request-response latency, outstanding
transactions, inter transaction time, transaction count, and address
distribution. The monitor can be used in combination with periodic
resetting and dumping of stats (through schedStatEvent) to study the
behaviour over time.
In future patches, a selection of convenience scripts will be added to
aid in visualising the statistics collected by the monitor.
This patch adds a guarding if-statement to avoid forwarding
uncacheable requests (or rather their corresponding request packets)
to bus snoopers. These packets should never have any effect on the
caches, and thus there is no need to forward them to the snoopers.
This patch fixes a bug that caused snoop requests to be placed in a
packet queue. Instead, the packet is now sent immediately using
sendTimingSnoopReq, thus bypassing the packet queue and any normal
responses waiting to be sent.
This patch moves send/recvTiming and send/recvTimingSnoop from the
Port base class to the MasterPort and SlavePort, and also splits them
into separate member functions for requests and responses:
send/recvTimingReq, send/recvTimingResp, and send/recvTimingSnoopReq,
send/recvTimingSnoopResp. A master port sends requests and receives
responses, and also receives snoop requests and sends snoop
responses. A slave port has the reciprocal behaviour as it receives
requests and sends responses, and sends snoop requests and receives
snoop responses.
For all MemObjects that have only master ports or slave ports (but not
both), e.g. a CPU, or a PIO device, this patch merely adds more
clarity to what kind of access is taking place. For example, a CPU
port used to call sendTiming, and will now call
sendTimingReq. Similarly, a response previously came back through
recvTiming, which is now recvTimingResp. For the modules that have
both master and slave ports, e.g. the bus, the behaviour was
previously relying on branches based on pkt->isRequest(), and this is
now replaced with a direct call to the apprioriate member function
depending on the type of access. Please note that send/recvRetry is
still shared by all the timing accessors and remains in the Port base
class for now (to maintain the current bus functionality and avoid
changing the statistics of all regressions).
The packet queue is split into a MasterPort and SlavePort version to
facilitate the use of the new timing accessors. All uses of the
PacketQueue are updated accordingly.
With this patch, the type of packet (request or response) is now well
defined for each type of access, and asserts on pkt->isRequest() and
pkt->isResponse() are now moved to the appropriate send member
functions. It is also worth noting that sendTimingSnoopReq no longer
returns a boolean, as the semantics do not alow snoop requests to be
rejected or stalled. All these assumptions are now excplicitly part of
the port interface itself.
This patch makes some rather trivial simplifications to the bus in
that it changes the use of BusMasterPort and BusSlavePort pointers to
simply use MasterPort and SlavePort (iterators are also updated
accordingly).
This change is a step towards a future patch that introduces a
separation of the interface and the structural port itself.
This patch introduces the PortId type, moves the definition of
INVALID_PORT_ID to the Port class, and also gives every port an id to
reflect the fact that each element in a vector port has an
identifier/index.
Previously the bus and Ruby testers (and potentially other users of
the vector ports) added the id field in their port subclasses, and now
this functionality is always present as it is moved to the base class.
This patch changes the guards for the definition of hash functions to
also exclude the int64_t and uint64_t hash functions in the case we
are using the c++0x STL <unordered_map> (and <hash>) or the TR1
version of the same header. Previously the guard only covered the hash
function for strings, but it seems there is also no need to define a
hash for the 64-bit integer types, and this has caused problems with
builds on 32-bit Ubuntu.
It's possible for two page table walks to overlap which will go in the same
place in the TLB's trie. They would land on top of each other, so this change
adds some code which detects if an address already matches an entry and if so
throws away the new one.
Put the { on the same line as the if and put a space between the if and the
open paren. Also, use the # format modifier which puts a 0x in front of hex
values automatically. If the ExtMachInst type isn't integral and actually
prints something more complicated, the # falls away harmlessly and we aren't
left with a phantom 0x followed by a bunch of unrelated text.
The parameter is _machInst, which is very similar to the member machInst. If
machInst is used to pass the parameter to a lower level constructor, what
really happens is that machInst is set to whatever it already happened to be,
effectively leaving it uninitialized.
This change also adjusts the TlbEntry class so that it stores the number of
address bits wide a page is rather than its size in bytes. In other words,
instead of storing 4K for a 4K page, it stores 12. 12 is easy to turn into 4K,
but it's a little harder going the other way.
This change adds a trie data structure which stores an arbitrary pointer type
based on an address and a number of relevant bits. Then lookups can be done
against the trie where the tree is traversed and the first legitimate match
found is returned.
This patch simplifies future patches by changing the pointer type used
in a number of the Ruby testers to use MasterPort instead of using a
derived CpuPort class. There is no reason for using the more
specialised pointers, and there is no longer a need to do any casting.
With the latest changes to the tester, organising ports as readers and
writes, things got a bit more complicated, and the "type" now had to
be removed to be able to fall back to using MasterPort rather than
CpuPort.
This patch simplifies the packet by removing the broadcast flag and
instead more firmly relying on (and enforcing) the semantics of
transactions in the classic memory system, i.e. request packets are
routed from a master to a slave based on the address, and when they
are created they have neither a valid source, nor destination. On
their way to the slave, the request packet is updated with a source
field for all modules that multiplex packets from multiple master
(e.g. a bus). When a request packet is turned into a response packet
(at the final slave), it moves the potentially populated source field
to the destination field, and the response packet is routed through
any multiplexing components back to the master based on the
destination field.
Modules that connect multiplexing components, such as caches and
bridges store any existing source and destination field in the sender
state as a stack (just as before).
The packet constructor is simplified in that there is no longer a need
to pass the Packet::Broadcast as the destination (this was always the
case for the classic memory system). In the case of Ruby, rather than
using the parameter to the constructor we now rely on setDest, as
there is already another three-argument constructor in the packet
class.
In many places where the packet information was printed as part of
DPRINTFs, request packets would be printed with a numeric "dest" that
would always be -1 (Broadcast) and that field is now removed from the
printing.
This patch introduces port access methods that separates snoop
request/responses from normal memory request/responses. The
differentiation is made for functional, atomic and timing accesses and
builds on the introduction of master and slave ports.
Before the introduction of this patch, the packets belonging to the
different phases of the protocol (request -> [forwarded snoop request
-> snoop response]* -> response) all use the same port access
functions, even though the snoop packets flow in the opposite
direction to the normal packet. That is, a coherent master sends
normal request and receives responses, but receives snoop requests and
sends snoop responses (vice versa for the slave). These two distinct
phases now use different access functions, as described below.
Starting with the functional access, a master sends a request to a
slave through sendFunctional, and the request packet is turned into a
response before the call returns. In a system without cache coherence,
this is all that is needed from the functional interface. For the
cache-coherent scenario, a slave also sends snoop requests to coherent
masters through sendFunctionalSnoop, with responses returned within
the same packet pointer. This is currently used by the bus and caches,
and the LSQ of the O3 CPU. The send/recvFunctional and
send/recvFunctionalSnoop are moved from the Port super class to the
appropriate subclass.
Atomic accesses follow the same flow as functional accesses, with
request being sent from master to slave through sendAtomic. In the
case of cache-coherent ports, a slave can send snoop requests to a
master through sendAtomicSnoop. Just as for the functional access
methods, the atomic send and receive member functions are moved to the
appropriate subclasses.
The timing access methods are different from the functional and atomic
in that requests and responses are separated in time and
send/recvTiming are used for both directions. Hence, a master uses
sendTiming to send a request to a slave, and a slave uses sendTiming
to send a response back to a master, at a later point in time. Snoop
requests and responses travel in the opposite direction, similar to
what happens in functional and atomic accesses. With the introduction
of this patch, it is possible to determine the direction of packets in
the bus, and no longer necessary to look for both a master and a slave
port with the requested port id.
In contrast to the normal recvFunctional, recvAtomic and recvTiming
that are pure virtual functions, the recvFunctionalSnoop,
recvAtomicSnoop and recvTimingSnoop have a default implementation that
calls panic. This is to allow non-coherent master and slave ports to
not implement these functions.
This patch adds a very basic pretty-printing of the test status
(passed or failed) to highlight failing tests even more: green for
passed, and red for failed. The printing only uses ANSI it the target
output is a tty and supports ANSI colours. Hence, any regression
scripts that are outputting to files or sending e-mails etc should
still be fine.
This patch addresses a number of minor issues that cause problems when
compiling with clang >= 3.0 and gcc >= 4.6. Most importantly, it
avoids using the deprecated ext/hash_map and instead uses
unordered_map (and similarly so for the hash_set). To make use of the
new STL containers, g++ and clang has to be invoked with "-std=c++0x",
and this is now added for all gcc versions >= 4.6, and for clang >=
3.0. For gcc >= 4.3 and <= 4.5 and clang <= 3.0 we use the tr1
unordered_map to avoid the deprecation warning.
The addition of c++0x in turn causes a few problems, as the
compiler is more stringent and adds a number of new warnings. Below,
the most important issues are enumerated:
1) the use of namespaces is more strict, e.g. for isnan, and all
headers opening the entire namespace std are now fixed.
2) another other issue caused by the more stringent compiler is the
narrowing of the embedded python, which used to be a char array,
and is now unsigned char since there were values larger than 128.
3) a particularly odd issue that arose with the new c++0x behaviour is
found in range.hh, where the operator< causes gcc to complain about
the template type parsing (the "<" is interpreted as the beginning
of a template argument), and the problem seems to be related to the
begin/end members introduced for the range-type iteration, which is
a new feature in c++11.
As a minor update, this patch also fixes the build flags for the clang
debug target that used to be shared with gcc and incorrectly use
"-ggdb".
Partial backout of cset 8b223e308b08.
Although it's great that there's currently no need
for Werror=false in the current tree, some of us
have uncommitted code that still needs this option.
This patch fixes a bug in Ruby that caused non-deterministic
simulation when changing the underlying hash map implementation. The
reason is order-dependent behaviour in combination with iteration over
the hash map contents. The two locations where a sorted container is
assumed are now changed to make use of a std::map instead of the
unordered hash map.
With this change, the stats changes slightly and the follow-on
changeset will update the relevant statistics.
Fixes checkpointing with respect to lost events after swapping event queues.
Also adds DPRINTFs to better understand what's going on when Ruby serializes
and unserializes.
This patch removes the assumption on having on single instance of
PhysicalMemory, and enables a distributed memory where the individual
memories in the system are each responsible for a single contiguous
address range.
All memories inherit from an AbstractMemory that encompasses the basic
behaviuor of a random access memory, and provides untimed access
methods. What was previously called PhysicalMemory is now
SimpleMemory, and a subclass of AbstractMemory. All future types of
memory controllers should inherit from AbstractMemory.
To enable e.g. the atomic CPU and RubyPort to access the now
distributed memory, the system has a wrapper class, called
PhysicalMemory that is aware of all the memories in the system and
their associated address ranges. This class thus acts as an
infinitely-fast bus and performs address decoding for these "shortcut"
accesses. Each memory can specify that it should not be part of the
global address map (used e.g. by the functional memories by some
testers). Moreover, each memory can be configured to be reported to
the OS configuration table, useful for populating ATAG structures, and
any potential ACPI tables.
Checkpointing support currently assumes that all memories have the
same size and organisation when creating and resuming from the
checkpoint. A future patch will enable a more flexible
re-organisation.
--HG--
rename : src/mem/PhysicalMemory.py => src/mem/AbstractMemory.py
rename : src/mem/PhysicalMemory.py => src/mem/SimpleMemory.py
rename : src/mem/physical.cc => src/mem/abstract_mem.cc
rename : src/mem/physical.hh => src/mem/abstract_mem.hh
rename : src/mem/physical.cc => src/mem/simple_mem.cc
rename : src/mem/physical.hh => src/mem/simple_mem.hh
With recent changes to the memory system, a port cannot be assigned a peer
port twice. While making use of the Ruby memory system in FS mode, DMA
ports were assigned peer twice, once for the classic memory system
and once for the Ruby memory system. This patch removes this double
assignment of peer ports.
This patch changes the behaviour of the All proxy parameter to not
only consider the direct children, but also do a pre-order depth-first
traversal of the object tree and append all results from the
children.
This is used in a later patch to find all the memories in the system,
independent of where they are located in the hierarchy.
This patch removes the physmem_port from the Atomic CPU and instead
uses the system pointer to access the physmem when using the fastmem
option. The system already keeps track of the physmem and the valid
memory address ranges, and with this patch we merely make use of that
existing functionality. As a result of this change, the overloaded
getMasterPort in the Atomic CPU can be removed, thus unifying the CPUs.
Virtual (pre-segmentation) addresses are truncated based on address size, and
any non-64 bit linear address is truncated to 32 bits. This means that real
mode addresses aren't truncated down to 16 bits after their segment bases are
added in.
This patch removes the DRAM memory class in preparation for updates to
the memory system, with the first one introducing an abstract memory
class, and removing the assumption of a single physical memory.
This patch removes the physMemPort from the RubySequencer and instead
uses the system pointer to access the physmem. The system already
keeps track of the physmem and the valid memory address ranges, and
with this patch we merely make use of that existing functionality. The
memory is modified so that it is possible to call the access functions
(atomic and functional) without going through the port, and the memory
is allowed to be unconnected, i.e. have no ports (since Ruby does not
attach it like the conventional memory system).
This patch introduces the notion of a master and slave port in the C++
code, thus bringing the previous classification from the Python
classes into the corresponding simulation objects and memory objects.
The patch enables us to classify behaviours into the two bins and add
assumptions and enfore compliance, also simplifying the two
interfaces. As a starting point, isSnooping is confined to a master
port, and getAddrRanges to slave ports. More of these specilisations
are to come in later patches.
The getPort function is not getMasterPort and getSlavePort, and
returns a port reference rather than a pointer as NULL would never be
a valid return value. The default implementation of these two
functions is placed in MemObject, and calls fatal.
The one drawback with this specific patch is that it requires some
code duplication, e.g. QueuedPort becomes QueuedMasterPort and
QueuedSlavePort, and BusPort becomes BusMasterPort and BusSlavePort
(avoiding multiple inheritance). With the later introduction of the
port interfaces, moving the functionality outside the port itself, a
lot of the duplicated code will disappear again.
This patch unifies where initMemProxies is called, in the init()
method of each BaseCPU subclass, before TheISA::initCPU is
called. Moreover, it also ensures that initMemProxies is called in
both full-system and syscall-emulation mode, thus unifying also across
the modes. An additional check is added in the ThreadState to ensure
that initMemProxies is only called once.
This patch changes the name of a bitfield from W to W_FIELD to avoid
clashes with W being used as a class (typename) in the templatized
range_map. It also changes L to L_FIELD to avoid future problems. The
problem manifestes itself when the CPU includes a header that in turn
includes range_map.hh. The relevant parts of the decoder are updated.
This patch unifies the recvFunctional, recvAtomic and recvTiming to
all be based on a similar structure: 1) extract information about the
incoming packet, 2) send it out to the appropriate snoopers, 3)
determine where it is going, and 4) forward it to the right
destination. The naming of variables across the different access
functions is now consistent as well.
Additionally, the patch introduces the member functions releaseBus and
retryWaiting to better distinguish between the two cases when we
should tell a sender to retry. The first case is when the bus goes
from busy to idle, and the second case is when it receives a retry
from a destination that did not immediatelly accept a packet.
As a very minor change, the MMU debug flag is no longer used in the bus.
This patch decouples the queueing and the port interactions to
simplify the introduction of the master and slave ports. By separating
the queueing functionality from the port itself, it becomes much
easier to distinguish between master and slave ports, and still retain
the queueing ability for both (without code duplication).
As part of the split into a PacketQueue and a port, there is now also
a hierarchy of two port classes, QueuedPort and SimpleTimingPort. The
QueuedPort is useful for ports that want to leave the packet
transmission of outgoing packets to the queue and is used by both
master and slave ports. The SimpleTimingPort inherits from the
QueuedPort and adds the implemention of recvTiming and recvFunctional
through recvAtomic.
The PioPort and MessagePort are cleaned up as part of the changes.
--HG--
rename : src/mem/tport.cc => src/mem/packet_queue.cc
rename : src/mem/tport.hh => src/mem/packet_queue.hh
This patch removes the overriding of "-Werror" in a handful of
cases. The code compiles with gcc 4.6.3 and clang 3.0 without any
warnings, and thus without any errors. There are no functional changes
introduced by this patch. In the future, rather than ypassing
"-Werror", address the warnings.
This patch cleans up a number of minor issues aiming to get closer to
compliance with the C++0x standard as interpreted by gcc and clang
(compile with std=c++0x and -pedantic-errors). In particular, the
patch cleans up enums where the last item was succeded by a comma,
namespaces closed by a curcly brace followed by a semi-colon, and the
use of the GNU-extension typeof (replaced by templated functions). It
does not address variable-length arrays, zero-size arrays, anonymous
structs, range expressions in switch statements, and the use of long
long. The generated CPU code also has a large number of issues that
remain to be fixed, mainly related to overflows in implicit constant
conversion (due to shifts).
This patch makes the code compile with clang 2.9 and 3.0 again by
making two very minor changes. Firt, it maintains a strict typing in
the forward declaration of the BaseCPUParams. Second, it adds a
FullSystemInt flag of the type unsigned int next to the boolean
FullSystem flag. The FullSystemInt variable can be used in
decode-statements (expands to switch statements) in the instruction
decoder.
Making the CheckerCPU a runtime time option requires the code to be compatible
with ISAs other than ARM. This patch adds the appropriate function
stubs to allow compilation.
Enables the CheckerCPU to be selected at runtime with the --checker option
from the configs/example/fs.py and configs/example/se.py configuration
files. Also merges with the SE/FS changes.
The change to port proxies recently moved code out of the constructor into
initState(). This is needed for code that loads data into memory, however
for code that setups symbol tables, kernel based events, etc this is the wrong
thing to do as that code is only called when a checkpoint isn't being restored
from.
1. --implicit-cache behavior is default.
2. makeEnv in src/SConscript is conditionally called.
3. decider set to MD5-timestamp
4. NO_HTML build option changed to SLICC_HTML (defaults to False)
This patch adds a creation-time check to the CPU to ensure that the
interrupt controller is created for the cases where it is needed,
i.e. if the CPU is not being switched in later and not a checker CPU.
The patch also adds the "createInterruptController" call to a number
of the regression scripts.
This patch renames the sendTiming member function in the RubyPort to
avoid inadvertently hiding Port::sendTiming (discovered through some
rather painful debugging). The RubyPort does, in fact, rely on the
functionality of the queued port and the implementation merely
schedules a send the next cycle. The new name for the member function
is sendNextCycle to better reflect this behaviour.
In the unlikely event that we ever shift to using C++11 the member
functions in Port should have a "final" identifier to prevent any
overriding in derived classes.
