Cleanup PCI devices to avoid using the PciDevice::platform pointer
directly. The PCI-specific functionality provided by the Platform
should be accessed through the wrappers in PciDevice.
This patch adds the necessary commands and cache functionality to
allow clean writebacks. This functionality is crucial, especially when
having exclusive (victim) caches. For example, if read-only L1
instruction caches are not sending clean writebacks, there will never
be any spills from the L1 to the L2. At the moment the cache model
defaults to not sending clean writebacks, and this should possibly be
re-evaluated.
The implementation of clean writebacks relies on a new packet command
WritebackClean, which acts much like a Writeback (renamed
WritebackDirty), and also much like a CleanEvict. On eviction of a
clean block the cache either sends a clean evict, or a clean
writeback, and if any copies are still cached upstream the clean
evict/writeback is dropped. Similarly, if a clean evict/writeback
reaches a cache where there are outstanding MSHRs for the block, the
packet is dropped. In the typical case though, the clean writeback
allocates a block in the downstream cache, and marks it writable if
the evicted block was writable.
The patch changes the O3_ARM_v7a L1 cache configuration and the
default L1 caches in config/common/Caches.py
This patch adds a parameter to control the cache clusivity, that is if
the cache is mostly inclusive or exclusive. At the moment there is no
intention to support strict policies, and thus the options are: 1)
mostly inclusive, or 2) mostly exclusive.
The choice of policy guides the behaviuor on a cache fill, and a new
helper function, allocOnFill, is created to encapsulate the decision
making process. For the timing mode, the decision is annotated on the
MSHR on sending out the downstream packet, and in atomic we directly
pass the decision to handleFill. We (ab)use the tempBlock in cases
where we are not allocating on fill, leaving the rest of the cache
unaffected. Simple and effective.
This patch also makes it more explicit that multiple caches are
allowed to consider a block writable (this is the case
also before this patch). That is, for a mostly inclusive cache,
multiple caches upstream may also consider the block exclusive. The
caches considering the block writable/exclusive all appear along the
same path to memory, and from a coherency protocol point of view it
works due to the fact that we always snoop upwards in zero time before
querying any downstream cache.
Note that this patch does not introduce clean writebacks. Thus, for
clean lines we are essentially removing a cache level if it is made
mostly exclusive. For example, lines from the read-only L1 instruction
cache or table-walker cache are always clean, and simply get dropped
rather than being passed to the L2. If the L2 is mostly exclusive and
does not allocate on fill it will thus never hold the line. A follow
on patch adds the clean writebacks.
The patch changes the L2 of the O3_ARM_v7a CPU configuration to be
mostly exclusive (and stats are affected accordingly).
This patch optimises the handling of writebacks and clean evictions
when using a snoop filter. Instead of snooping into the caches to
determine if the block is cached or not, simply set the status based
on the snoop-filter result.
Instead of conservatively enforcing order for all packets, which may
negatively impact the simulated-system performance, this patch updates
the packet queue such that it only applies the restriction if there
are already packets with the same address in the queue.
The basic need for the order enforcement is due to coherency
interactions where requests/responses to the same cache line must not
over-take each other. We rely on the fact that any packet that needs
order enforcement will have a block-aligned address. Thus, there is no
need for the queue to know about the cacheline size.
This patch enforces insertion order transmission of packets on the
response path in the cache. Note that the logic to enforce order is
already present in the packet queue, this patch simply turns it on for
queues in the response path.
Without this patch, there are corner cases where a request-response is
faster than a response-response forwarded through the cache. This
violation of queuing order causes problems in the snoop filter leaving
it with inaccurate information. This causes assert failures in the
snoop filter later on.
A follow on patch relaxes the order enforcement in the packet queue to
limit the performance impact.
This patch updates the I/O devices, bridge and simple memory to take
the packet header and payload delay into account in their latency
calculations. In all cases we add the header delay, i.e. the
accumulated pipeline delay of any crossbars, and the payload delay
needed for deserialisation of any payload.
Due to the additional unknown latency contribution, the packet queue
of the simple memory is changed to use insertion sorting based on the
time stamp. Moreover, since the memory hands out exclusive (non
shared) responses, we also need to ensure ordering for reads to the
same address.
This patch aligns how the memory-system slaves, i.e. the various
memory controllers and the bridge, identify and deal with sinking of
inhibited packets that are only useful within the coherent part of the
memory system.
In the future we could shift the onus to the crossbar, and add a
parameter "is_point_of_coherence" that would allow it to sink the
aforementioned packets.
This patch changes the CleanEvict command type to not be considered a
write. Initially it was made a zero-sized write to match the writeback
command, but as things developed it became clear that it causes more
problems than it solves. For example, the memory modules (and bridge)
should not consider the CleanEvict as a write, but instead discard
it. With this patch it will be neither a read, nor write, and as it
does not need a response the slave will simply sink it.
This patch unifies how we deal with delayed packet deletion, where the
receiving slave is responsible for deleting the packet, but the
sending agent (e.g. a cache) is still relying on the pointer until the
call to sendTimingReq completes. Previously we used a mix of a
deletion vector and a construct using unique_ptr. With this patch we
ensure all slaves use the latter approach.
The CoherentXBar currently doesn't check its queued slave ports when
receiving a functional snoop. This caused data corruption in cases
when a modified cache lines is forwarded between two caches.
Add the required functional calls into the queued slave ports.
This changeset adds a serial link model for the Hybrid Memory Cube (HMC).
SerialLink is a simple variation of the Bridge class, with the ability to
account for the latency of packet serialization. Also trySendTiming has been
modified to correctly model bandwidth.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch models a simple HMC Controller. It simply schedules the incoming
packets to HMC Serial Links using a round robin mechanism. This patch should
be applied in series with other patches modeling a complete HMC device.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Fix a bug in which the flash device would write out of bounds and
could either trigger a segfault and corrupt the memory of other
objects. This was caused by using pageSize in the place of
pagesPerBlock when running the garbage collector.
Also, added an assert to flag this condition in the future.
This patch fixes the drain logic for the UFSHostDevice and the
FlashDevice. In the case of the FlashDevice, the logic for CheckDrain
needed to be reversed, whilst in the case of the UFSHostDevice check
drain was never being called. In both cases the system would never
complete draining if the initial attampt to drain failed.
This patch addresses the upgrading of deferred targets in the MSHR,
and makes it clearer by explicitly calling out what is happening
(deferred targets are promoted if we get exclusivity without asking
for it).
This patch adds explicit overrides as this is now required when using
"-Wall" with clang >= 3.5, the latter now part of the most recent
XCode. The patch consequently removes "virtual" for those methods
where "override" is added. The latter should be enough of an
indication.
As part of this patch, a few minor issues that clang >= 3.5 complains
about are also resolved (unused methods and variables).
This patch moves away from using M5_ATTR_OVERRIDE and the m5::hashmap
(and similar) abstractions, as these are no longer needed with gcc 4.7
and clang 3.1 as minimum compiler versions.
ARM uses UDelayEvents to emulate kernel __*udelay functions and speed up
simulation. UDelayEvents call Pseudoinst::quiesceNs to quiesce the system for
a specified delay. Changeset 10341:0b4d10f53c2d introduced the requirement
that any quiesce process that is started must also be completed by scheduling
an EndQuiesceEvent. This change causes the CPU to hang if an IsQuiesce
instruction is executed, but the corresponding EndQuiesceEvent is not
scheduled.
Changeset 11058:d0934b57735a introduces a fix for uses of PseudoInst::quiesce*
that would conditionally execute the EndQuiesceEvent. ARM UDelayEvents specify
quiesce period of 0 ns (src/arch/arm/linux/system.cc), so changeset 11058
causes these events to now execute full quiesce processes, greatly increasing
the total instructions executed in kernel delay loops and slowing simulation.
This patch updates the UDelayEvent to conditionally execute
PseudoInst::quiesceNs (**a quiesce operation**) only if the specified
delay is >0 ns. The result is ARM delay loops no longer execute instructions
for quiesce handling, and regression time returns to normal.
The decoder is responsible for splitting instructions in micro
operations (uops). Given that different micro architectures may split
operations differently, this patch allows to specify which micro
architecture each isa implements, so different cores in the system can
split instructions differently, also decoupling uop splitting
(microArch) from ISA (Arch). This is done making the decodification
calls templates that receive a type 'DecoderFlavour' that maps the
name of the operation to the class that implements it. This way there
is only one selection point (converting the command line enum to the
appropriate DecodeFeatures object). In addition, there is no explicit
code replication: template instantiation hides that, and the compiler
should be able to resolve a number of things at compile-time.
Although some decent error messages were getting generated inside
isa_parser.py, they weren't always getting printed because of the
screwy way we were handling exceptions. (Basically an inner
exception would get hidden by an outer exception, and the more
informative inner error message would not get printed.)
Also line numbers were messed up, since they were taken from the
lexer, which is typically a token (or more) ahead of the grammar
rule that's being matched. Using the 'lineno' attribute that
PLY associates with the grammar production is more accurate.
The new LineTracker class extends lineno to track filenames as
well as line numbers.
This information is useful if you have a bunch of simulations running
and want to know which one to kill, but you've neglected to take
advantage of the previous patch and embed the pid in your output path.
These are packed single-precision approximate reciprocal operations,
vector and scalar versions, respectively.
This code was basically developed by copying the code for
sqrtps and sqrtss. The mrcp micro-op was simplified relative to
msqrt since there are no double-precision versions of this operation.
fild loads an integer value into the x87 top of stack register.
fucomi/fucomip compare two x87 register values (the latter
also doing a stack pop).
These instructions are used by some versions of GNU libstdc++.
The DTRACE() macro tests both Trace::enabled and the specific flag. This
change uses the same administrative interface for enabling/disabling
tracing, but masks the SimpleFlags settings directly. This eliminates a
load for every DTRACE() test, e.g. DPRINTF.
In ARM, certain variables are only updated when a necessary change is
detected. Having 2 SMT threads share a TLB resulted in these not being
updated as required. This patch adds a thread context identifer to
assist in the invalidation of these variables.
Adds SMT support to the "simple" CPU models so that they can be
used with other SMT-supported CPUs. Example usage: this enables
the TimingSimpleCPU to be used to warmup caches before swapping to
detailed mode with the in-order or out-of-order based CPU models.
Trying to run an SE system with varying threads per core (SMT cores + Non-SMT
cores) caused failures due to the CPU id assignment logic. The comment
about thread assignment (worrying about core 0 not having tid 0) seems
not to be valid given that our configuration scripts initialize them in
order.
This removes that constraint so a heterogenously threaded sytem can work.
If a cache entry permission was previously set to NotPresent, but the entry was
not deleted, a following cache allocation can cause the entry to be leaked by
setting the entry pointer to a newly allocated entry. To eliminate this
possibility, check if the new entry is different from the old one, and if so,
delete the old one.
IntDevice::recvResponse is called from two places in current mainline: (1) the
short circuit path of X86ISA::IntDevice::IntMasterPort::sendMessage for atomic
mode, and (2) the full request->response path to and from the x86 interrupts
device (finally called from MessageMasterPort::recvTimingResp). In the former
case, the packet was deleted correctly, but in the latter case, the packet and
request leak. To fix the leak, move request and packet deletion into IntDevice
inherited class implementations of recvResponse.
In RubyPort::ruby_eviction_callback, prior changes fixed a memory leak caused
by instantiating separate packets for each port that the eviction was forwarded
to. That change, however, left the instantiated request to also leak. Allocate
it on the stack to avoid the leak.
Recent changes to memory access queuing allocate requests for packets sent to
memory controllers, but did not free the requests. Delete them to avoid leaks.
Changes to the RubyMemoryControl removed the dequeue function, which deleted
MemoryNode instances. This results in leaked MemoryNode instances. Correctly
delete these instances.
The recent changeset to readlink() to handle reading the /proc/self/exe link
introduces a number of problems. This patch fixes two:
1) Because readlink() called on /proc/self/exe now uses LiveProcess::progName()
to find the binary path, it will only get the zeroth parameter of the simulated
system command line. However, if a config script also specifies the process'
executable, the executable parameter is used to create the LiveProcess rather
than the zeroth command line parameter. Thus, the zeroth command line parameter
is not necessarily the correct path to the binary executing in the simulated
system. To fix this, add a LiveProcess data member, 'executable', which is
correctly set during instantiation and returned from progName().
2) If a config script allows a user to pass a relative path as the zeroth
simulated system command line parameter or process executable, readlink() will
incorrecly return a relative path when called on '/proc/self/exe'.
/proc/self/exe is always set to a full path, so running benchmarks can fail if
a relative path is returned. To fix this, clean up the handling of
LiveProcess::progName() within readlink() to get the full binary path.
NOTE: This patch still leaves the potential problem that host full path to the
binary bleeds into the simulated system, potentially causing the appearance of
non-deterministic simulated system execution.
This patch fixes a use-after-delete issue in the packet probe points
by adding a PacketInfo struct to retain the key fields before passing
the packet onwards. We want to probe the packet after it is
successfully sent, but by that time the fields may be modified, and
the packet may even be deleted.
Amazingly enough the issue has gone undetected for months, and only
recently popped up in our regressions.
This patch fixes issues in the interactions between deferred snoops
and WriteLineReq. More specifically, the patch addresses an issue
where deferred snoops caused assertion failures when being serviced on
the arrival of an InvalidateResp. The response packet was perceived to
be invalidating, when actually it is not for the cache that sent out
the original invalidation request.
This patch changes the tracking of ports in the snoop filter to use
local dense port IDs so that we can have 64 snooping ports (rather
than crossbar slave ports). This is achieved by adding a simple
remapping vector that translates the actal port IDs into the local
slave IDs used in the SnoopMask.
Ultimately this patch allows us to scale to much larger systems
without introducing a hierarchy of crossbars.
This patch adds a snoop filter to the L2XBar. For now we refrain from
globally adding a snoop filter to the SystemXBar, since the latter is
also used in systems without caches. In scenarios without caches the
snoop filter will not see any writeback/clean evicts from the CPU
ports, despite the fact that they are snooping. To avoid inadvertent
use of the snoop filter in these cases we leave it out for now.
A size check is added to the snoop filter, merely to ensure it does
not grow beyond the total capacity of the caches above it. The size
has to be set manually, and a value of 8 MByte is choosen as suitably
high default.
This patch introduces a private member storing the iterator from the
lookupRequest call, such that it can be re-used when the request
eventually finishes. The method previously called updateRequest is
renamed finishRequest to make it more clear that the two functions
must be called together.
This patch mirrors the logic in timing mode which sends up snoops to
check for cached copies before sending CleanEvicts and Writebacks down
the memory hierarchy. In case there is a copy in a cache above,
discard CleanEvicts and set the BLOCK_CACHED flag in Writebacks so
that writebacks do not reset the cache residency bit in the snoop
filter below.
This patch adds the functionality to properly track CleanEvicts and
Writebacks in the snoop filter. Previously there were no CleanEvicts, and
Writebacks did not send up snoops to ensure there were no copies in
caches above. Hence a writeback could never erase an entry from the
snoop filter.
When a CleanEvict message reaches a snoop filter, it confirms that the
BLOCK_CACHED flag is not set and resets the bits corresponding to the
CleanEvict address and port it arrived on. If none of the other peer
caches have (or have requested) the block, the snoop filter forwards
the CleanEvict to lower levels of memory. In case of a Writeback
message, the snoop filter checks if the BLOCK_CACHED flag is not set
and only then resets the bits corresponding to the Writeback
address. If any of the other peer caches have (or has requested) the
same block, the snoop filter sets the BLOCK_CACHED flag in the
Writeback before forwarding it to lower levels of memory heirarachy.
This patch prevents the snoop filter from creating items for requests
originating from non-snooping ports. The allocation decision is thus
based both on the cacheability of the line, and the snooping status of
the source port. Ultimately we should check if the source of the
packet is caching, since also the CPU ports are snooping (but not
allocating). Thus, at the moment we rely on the snoop filter being
used together with caches.
The patch also transitions to use the Packet::getBlockAddr in
determining the line address.
This patch introduces the concept of a snoop latency. Given the
requirement to snoop and forward packets in zero time (due to the
coherency mechanism), the latency is accounted for later.
On a snoop, we establish the latency, and later add it to the header
delay of the packet. To allow multiple caches to contribute to the
snoop latency, we use a separate variable in the packet, and then take
the maximum before adding it to the header delay.
This patch ensures that the snoop-filter latency only contributes to
the packet latency, and not to the crossbar throughput/occupancy. In
essence we treat the snoop-filter lookup as pipelined.
Created the following HBM configurations:
1) HBM gen1 (x128/CH), 2Gb die, 4H stack, 1Gbps, 8 channels
2) HBM gen2 (x64/PC), 8Gb die, 4H stack, 1Gbps, 16 pseudo-channels
The configuration values are based on:
- The HBM gen1 public JEDEC spec
- Publically released data from MemCon presentations
- Timing extrapolated from existing LPDDR configurations
Will adjust once specs become available.
Changeset 4872dbdea907 replaced Address by Addr, but did not make changes to
print statements. So the addresses which were being printed in hex earlier
along with their line address, were now being printed in decimals. This patch
adds a function printAddress(Addr) that can be used to print the address in hex
along with the lines address. This function has been put to use in some of the
places. At other places, change has been made to print just the address in
hex.
The DataMember class in Type.py was being derived from PairContainer. A
separate Var object was also created for the DataMember. This meant some
duplication of across the members of these two classes (Var and DataMember).
This patch changes DataMember from Var instead. There is no obvious reason to
derive from PairContainer which can only hold pairs, something that Var class
already supports. The only thing that DataMember has over Var is init_code,
which is being retained. This change would later on help in having pointers
in DataMembers.
Some blocks in MOESI hammer were not getting deallocated when they were set to
an idle state (e.g. by invalidate or other_getx/s messages). While
functionally correct, this caused some bad effects on performance, such as
blocks in I in the L1s getting sent to the L2 upon eviction, in turn evicting
valid blocks. Also, if a valid block was in LRU, that block could be evicted
rather than a block in I. This patch adds in the missing deallocations.
Committed by: Nilay Vaish<nilay@cs.wisc.edu>
The recent changes to make MessageBuffers SimObjects required them to be
initialized in a particular order, which could break some protocols. Fix this
by calling initNetQueues on the external nodes of each external link in the
constructor of Network.
This patch also refactors the duplicated code for checking network allocation
and setting net queues (which are called by initNetQueues) from the simple and
garnet networks to be in Network.
This patch changes MessageBuffer and TimerTable, two structures used for
buffering messages by components in ruby. These structures would no longer
maintain pointers to clock objects. Functions in these structures have been
changed to take as input current time in Tick. Similarly, these structures
will not operate on Cycle valued latencies for different operations. The
corresponding functions would need to be provided with these latencies by
components invoking the relevant functions. These latencies should also be
in Ticks.
I felt the need for these changes while trying to speed up ruby. The ultimate
aim is to eliminate Consumer class and replace it with an EventManager object in
the MessageBuffer and TimerTable classes. This object would be used for
scheduling events. The event itself would contain information on the object and
function to be invoked.
In hindsight, it seems I should have done this while I was moving away from use
of a single global clock in the memory system. That change led to introduction
of clock objects that replaced the global clock object. It never crossed my
mind that having clock object pointers is not a good design. And now I really
don't like the fact that we have separate consumer, receiver and sender
pointers in message buffers.
The eventual aim of this change is to pass RubySystem pointers through to
objects generated from the SLICC protocol code.
Because some of these objects need to dereference their RubySystem pointers,
they need access to the System.hh header file.
In src/mem/ruby/SConscript, the MakeInclude function creates single-line header
files in the build directory that do nothing except include the corresponding
header file from the source tree.
However, SLICC also generates a list of header files from its symbol table, and
writes it to mem/protocol/Types.hh in the build directory. This code assumes
that the header file name is the same as the class name.
The end result of this is the many of the generated slicc files try to include
RubySystem.hh, when the file they really need is System.hh. The path of least
resistence is just to rename System.hh to RubySystem.hh.
--HG--
rename : src/mem/ruby/system/System.cc => src/mem/ruby/system/RubySystem.cc
rename : src/mem/ruby/system/System.hh => src/mem/ruby/system/RubySystem.hh
This register is writable according to UA2005
Tried to boot NetBSD which starts the kernel by writing to the tick_cmpr
register. Without the patch gem5 crashes with a panic. With the patch NetBSD
starts to boot normally (although sun4v support in NetBSD is not complete yet)
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Handle bad IDE disk image size 0. When image size is 0, gem5 will cause an
exception with log "Floating point exception (core dumped)".
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
When a branch gets squashed, it's speculative branch predictor state should get
rolled back in squash(). However, only the globalHistory state was being
rolled back. This patch adds (at least some) support for rolling back the
local predictor state also.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch enables instructions in LSQ to track two physical addresses for
corresponding two split requests. Later, the information is used in
checksnoop() to search for/invalidate the corresponding LD instructions.
The current implementation has kept track of only the physical address that is
referenced by the first split request. Thus, for checksnoop(), the line
accessed by the second request has not been considered, causing potential
correctness issues.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Refactored the code in operateVnet(), moved partly to a new function
operateMessageBuffer(). This is required since a later patch moves to having a
wakeup event per MessageBuffer instead of one event for the entire Switch.
There are two reasons for doing so:
a. provide a source of clock to PerfectSwitch. A follow on patch removes sender
and receiver pointers from MessageBuffer means that the object owning the
buffer should have some way of providing timing info.
b. schedule events. A follow on patch removes the consumer class. So the
PerfectSwitch needs some EventManager object to schedule events on its own.
Add a stat that counts buffer underruns in the HDLCD controller. The
stat counts at most one underrun per frame since the controller aborts
the current frame if it underruns.
Rewrite the HDLCD controller to use the new DMA engine and pixel
pump. This fixes several bugs in the current implementation:
* Broken/missing interrupt support (VSync, underrun, DMA end)
* Fragile resolution changes (changing resolutions used
to cause assertion errors).
* Support for resolutions with a width that isn't divisible by 32.
* The pixel clock can now be set dynamically.
This breaks checkpoint compatibility. Checkpoints can be upgraded with
the checkpoint conversion script. However, upgraded checkpoints won't
contain the state of the current frame. That means that HDLCD
controllers restoring from a converted checkpoint immediately start
drawing a new frame (i.e, expect timing differences).
Currently the sequencer calls the function setMRU that updates the replacement
policy structures with the first level caches. While functionally this is
correct, the problem is that this requires calling findTagInSet() which is an
expensive function. This patch removes the calls to setMRU from the sequencer.
All controllers should now update the replacement policy on their own.
The set and the way index for a given cache entry can be found within the
AbstractCacheEntry structure. Use these indicies to update the replacement
policy structures.
The current Set data structure is slow and therefore is being reimplemented
using std::bitset. A maximum limit of 64 is being set on the number of
controllers of each type. This means that for simulating a system with more
controllers of a given type, one would need to change the value of the variable
NUMBER_BITS_PER_SET
MessageBuffer is a SimObject now. There were protocols that still declared
some of the message buffers are variables of the controller, but not as input
parameters. Special handling was required for these variables in the SLICC
compiler. This patch changes this. Now all message buffers are declared as
input parameters.
In cases where a newly added target does not have any upstream MSHR to
mark as downstreamPending, remember that nothing is marked. This
allows us to avoid attempting to find the MSHR as part of the clearing
of downstreamPending.
This commit addresses gem5 checkpoints' linear versioning bottleneck.
Since development is distributed across many private trees, there exists
a sort of 'race' for checkpoint version numbers: internally a checkpoint
version may be used but then resynchronizing with the external tree causes
a conflict on that version. This change replaces the linear version number
with a set of unique strings called tags. Now the only conflicts that can
arise are of tag names, where collisions are much easier to avoid.
The checkpoint upgrader (util/cpt_upgrader.py) upgrades the version
representation, as one would expect. Each tag version implements its
upgrader code in a python file in the util/cpt_upgraders directory
rather than adding a function to the upgrader script itself.
The version tags are stored in the 'Globals' section rather than 'root'
(as the version was previously) because 'Globals' gets unserialized
first and can provide a warning before any other unserialization errors
can occur.
This is in support of tag-based checkpoint versioning. It should be
possible to examine an optional parameter in a checkpoint during
unserialization and not have it throw a warning.
We no longer use the C library based random number generator: random().
Instead we use the C++ library provided rng. So setting the random seed for
the RubySystem class has no effect. Hence the variable and the corresponding
option are being dropped.
Event auto-serialization no longer in use and has been broken ever
since the introduction of PDES support almost two years
ago. Additionally, serializing the individual event queues is
undesirable since it exposes the thread structure of the
simulator. What this means in practice is that the number of threads
in the simulator must be the same when taking a checkpoint and when
loading the checkpoint.
This changeset removes support for the AutoSerialize event flag and
the associated serialization code.
EtherLink currently uses a fire-and-forget link delay event that
delays sending of packets by a fixed number of ticks. In order to
serialize this event, it relies on the event queue's auto
serialization support. However, support for event auto serialization
has been broken for more than two years, which means that checkpoints
of multi-system setups are likely to drop in-flight packets.
This changeset the replaces rewrites this part of the EtherLink to use
a packet queue instead. The queue contains a (tick, packet) tuple. The
tick indicates when the packet will be ready. Instead of relying on
event autoserialization, we now explicitly serialize the packet queue
in the EhterLink::Link class.
Note that this changeset changes the way in-flight packages are
serialized. Old checkpoints will still load, but in-flight packets
will be dropped (just as before). There has been no attempt to upgrade
checkpoints since this would actually change the behavior of existing
checkpoints.
This changeset removes the support for the autoserialize parameter in
GlobalSimLoopExitEvent (including exitSimLoop()) and
LocalSimLoopExitEvent.
Auto-serialization of the LocalSimLoopExitEvent was never used, so
this is not expected to affect anything. However, it was sometimes
used for GlobalSimLoopExitEvent. Unfortunately, serialization of
global events has never been supported, so checkpoints with such
events will currently cause simulation panics.
The serialize parameter to exitSimLoop() has been left in-place to
maintain API compatibility (removing it would affect m5ops). Instead
of just dropping it, we now print a warning if the parameter is set
and the exit event is scheduled in the future (i.e., not at the
current tick).
The object resolver isn't serialization specific and shouldn't live in
serialize.hh. Move it to sim_object.hh since it queries to the
SimObject hierarchy.
This member indicates whether or not a particular virtual network is in use.
Instead of having a default big value for the number of virtual networks and
then checking whether a virtual network is in use, the next patch removes the
default value and the protocol configuration file would now specify the
number of virtual networks it requires.
Additionally, the patch also refactors some of the code used for computing the
virtual channel next in the round robin order.
Both FuncCallExprAST and MethodCallExprAST had code for checking the arguments
with which a function is being called. The patch does away with this
duplication. Now the code for checking function call arguments resides in the
Func class.
The new serialization code (kudos to Tim Jones) moves all of the state
mangling in RubySystem to memWriteback. This makes it possible to use
the new const serialization interface.
This changeset moves the cache recorder cleanup from the checkpoint()
method to drainResume() to make checkpointing truly constant and
updates the checkpointing code to use the new interface.
The sequencer takes care of llsc accesses by calling upon functions
from the CacheMemory. This is unnecessary once the required CacheEntry object
is available. Thus some of the calls to findTagInSet() are avoided.
The O3CPU blocks the Fetch when it sees a quiesce instruction (IsQuiesce flag).
When the inst. is executed, a quiesce event is created to reactivate the
context and unblock the Fetch.
If the quiesceNs or quiesceCycles are called with a value of 0, the
QuiesceEvent will not be created and the Fetch stage will remain blocked.
Committed by Joel Hestness <jthestness@gmail.com>
This patch reverts part of (842f56345a42), as apparently there are
use-cases outside the main repository relying on the late setting of
the physical address.
This patch simplifies the packet, and removes the possibility of
creating a packet without a valid address and/or size. Under no
circumstances are these fields set at a later point, and thus they
really have to be provided at construction time.
The patch also fixes a case there the MinorCPU creates a packet
without a valid address and size, only to later delete it.
Cleaning up dead code. The CLREX stores zero directly to
MISCREG_LOCKFLAG and so the request flag is no longer needed. The
corresponding functionality in the cache tags is also removed.
Open up for other subclasses to BaseCache and transition to using the
explicit Cache subclass.
--HG--
rename : src/mem/cache/BaseCache.py => src/mem/cache/Cache.py
This patch serves to avoid name clashes with the classic cache. For
some reason having two 'SimObject' files with the same name creates
problems.
--HG--
rename : src/mem/ruby/structures/Cache.py => src/mem/ruby/structures/RubyCache.py
We no longer use the C library based random number generator: random().
Instead we use the C++ library provided rng. So setting the random seed for
the RubySystem class has no effect. Hence the variable and the corresponding
option are being dropped.
Currently the sequencer calls the function setMRU that updates the replacement
policy structures with the first level caches. While functionally this is
correct, the problem is that this requires calling findTagInSet() which is an
expensive function. This patch removes the calls to setMRU from the sequencer.
All controllers should now update the replacement policy on their own.
The set and the way index for a given cache entry can be found within the
AbstractCacheEntry structure. Use these indicies to update the replacement
policy structures.
Before this patch, while one could declare / define a function with default
argument values, but the actual function call would require one to specify
all the arguments. This patch changes the check for function arguments.
Now a function call needs to specify arguments that are at least as much as
those with default values and at most the total number of arguments taken
as input by the function.
Both FuncCallExprAST and MethodCallExprAST had code for checking the arguments
with which a function is being called. The patch does away with this
duplication. Now the code for checking function call arguments resides in the
Func class.
