Add a few constants and functions that the InOrder model wants for SPARC.
* * *
sparc: add eaComp function
InOrder separates the address generation from the actual access so give
Sparc that functionality
* * *
sparc: add control flags for branches
branch predictors and other cpu model functions need to know specific information
about branches, so add the necessary flags here
Calculation of offset to copy from storeQueue[idx].data structure for load to
store forwarding fixed to be difference in bytes between store and load virtual
addresses. Previous method would induce bug where a load would index into
buffer at the wrong location.
If a split load fails on a blocked cache wbOutstanding can be decremented
twice if the first part of the split load succeeds and the second part fails.
Condition the decrementing on not having completed the first part of the load.
This patch fixes two problems with the O3 cpu model. The first is an issue
with an instruction fetch causing a fault on the next address while the
current macro-op is being issued. This happens when the micro-ops exceed
the fetch bandwdith and then on the next cycle the fetch stage attempts
to issue a request to the next line while it still has micro-ops to issue
if the next line faults a fault is attached to a micro-op in the currently
executing macro-op rather than a "nop" from the next instruction block.
This leads to an instruction incorrectly faulting when on fetch when
it had no reason to fault.
A similar problem occurs with interrupts. When an interrupt occurs the
fetch stage nominally stops issuing instructions immediately. This is incorrect
in the case of a macro-op as the current location might not be interruptable.
Debug flags are ExecUser, ExecKernel, and ExecAsid. ExecUser and
ExecKernel are set by default when Exec is specified. Use minus
sign with ExecUser or ExecKernel to remove user or kernel tracing
respectively.
Instructions that load an address and are control instructions can
execute down the wrong path if they were predicted correctly and then
instructions following them are squashed. If an instruction is a
memory and control op use the predicted address for the next PC instead
of just advancing the PC. Without this change NPC is used for the next
instruction, but predPC is used to verify that the branch was successful
so the wrong path is silently executed.
The network tester terminates after injecting for sim_cycles
(default=1000), instead of having to explicitly pass --maxticks from the
command line as before. If fixed_pkts is enabled, the tester only
injects maxpackets number of packets, else it keeps injecting till sim_cycles.
The tester also works with zero command line arguments now.
At the same time, rename the trace flags to debug flags since they
have broader usage than simply tracing. This means that
--trace-flags is now --debug-flags and --trace-help is now --debug-help
This change fixes a small bug in the arm copyRegs() code where some registers
wouldn't be copied if the processor was in a mode other than MODE_USER.
Additionally, this change simplifies the way the O3 switchCpu code works by
utilizing TheISA::copyRegs() to copy the required context information
rather than the adhoc copying that goes on in the CPU model. The current code
makes assumptions about the visibility of int and float registers that aren't
true for all architectures in FS mode.
The comment in the code suggests that the checking granularity should be 16
bytes, however in reality the shift by 8 is 256 bytes which seems much
larger than required.
***
(1): get rid of expandForMT function
MIPS is the only ISA that cares about having a piece of ISA state integrate
multiple threads so add constants for MIPS and relieve the other ISAs from having
to define this. Also, InOrder was the only core that was actively calling
this function
* * *
(2): get rid of corespecific type
The CoreSpecific type was used as a proxy to pass in HW specific params to
a MIPS CPU, but since MIPS FS hasnt been touched for awhile, it makes sense
to not force every other ISA to use CoreSpecific as well use a special
reset function to set it. That probably should go in a PowerOn reset fault
anyway.
The tester code is in testers/networktest.
The tester can be invoked by configs/example/ruby_network_test.py.
A dummy coherence protocol called Network_test is also addded for network-only simulations and testing. The protocol takes in messages from the tester and just pushes them into the network in the appropriate vnet, without storing any state.
This change speeds up booting, especially in MP cases, by not executing
udelay() on the core but instead skipping ahead tha amount of time that is being
delayed.
This change fixes the problem for all the cases we actively use. If you want to try
more creative I/O device attachments (E.g. sharing an L2), this won't work. You
would need another level of caching between the I/O device and the cache
(which you actually need anyway with our current code to make sure writes
propagate). This is required so that you can mark the cache in between as
top level and it won't try to send ownership of a block to the I/O device.
Asserts have been added that should catch any issues.
Without this change the a store can be issued to the cache multiple times.
If this case occurs when the l1 cache is out of mshrs (and thus blocked)
the processor will never make forward progress because each cycle it will
send a single request using the recently freed mshr and not completing the
multipart store. This will continue forever.
There may not be a formally correct spelling for the past tense of mmap, but
mmapped is the spelling Google doesn't try to autocorrect. This makes sense
because it mirrors the past tense of map->mapped and not the past tense of
cape->caped.
--HG--
rename : src/arch/alpha/mmaped_ipr.hh => src/arch/alpha/mmapped_ipr.hh
rename : src/arch/arm/mmaped_ipr.hh => src/arch/arm/mmapped_ipr.hh
rename : src/arch/mips/mmaped_ipr.hh => src/arch/mips/mmapped_ipr.hh
rename : src/arch/power/mmaped_ipr.hh => src/arch/power/mmapped_ipr.hh
rename : src/arch/sparc/mmaped_ipr.hh => src/arch/sparc/mmapped_ipr.hh
rename : src/arch/x86/mmaped_ipr.hh => src/arch/x86/mmapped_ipr.hh
This patch changes DataBlock.hh so that it is not dependent on RubySystem.
This dependence seems unecessary. All those functions that depende on
RubySystem have been moved to DataBlock.cc file.
Because int and not InstSeqNum was used in a couple of places, you can
overflow the int type and thus get wierd bugs when the sequence number
is negative (or some wierd value)
remove constructors that werent being used (it just gets confusing)
use initialization list for all the variables instead of relying on initVars()
function
-use a pointer to CacheReqPacket instead of PacketPtr so correct destructors
get called on packet deletion
- make sure to delete the packet if the cache blocks the sendTiming request
or for some reason we dont use the packet
- dont overwrite memory requests since in the worst case an instruction will
be replaying a request so no need to keep allocating a new request
- we dont use retryPkt so delete it
- fetch code was split out already, so just assert that this is a memory
reference inst. and that the staticInst is available
If there is an outstanding table walk and no other activity in the CPU
it can go to sleep and never wake up. This change makes the instruction
queue always active if the CPU is waiting for a store to translate.
If Gabe changes the way this code works then the below should be removed
as indicated by the todo.
