There are two primary issues with this code which make it deserving of deletion.
1) GHB is a way to structure a prefetcher, not a definitive type of prefetcher
2) This prefetcher isn't even structured like a GHB prefetcher.
It's basically a worse version of the stride prefetcher.
It primarily serves to confuse new gem5 users and most functionality is already
present in the stride prefetcher.
The changeset ad9c042dce54 made changes to the structures under the network
directory to use a map of buffers instead of vector of buffers.
The reasoning was that not all vnets that are created are used and we
needlessly allocate more buffers than required and then iterate over them
while processing network messages. But the move to map resulted in a slow
down which was pointed out by Andreas Hansson. This patch moves things
back to using vector of message buffers.
Static analysis unearther a bunch of uninitialised variables and
members, and this patch addresses the problem. In all cases these
omissions seem benign in the end, but at least fixing them means less
false positives next time round.
This patch tidies up random number generation to ensure that it is
done consistently throughout the code base. In essence this involves a
clean-up of Ruby, and some code simplifications in the traffic
generator.
As part of this patch a bunch of skewed distributions (off-by-one etc)
have been fixed.
Note that a single global random number generator is used, and that
the object instantiation order will impact the behaviour (the sequence
of numbers will be unaffected, but if module A calles random before
module B then they would obviously see a different outcome). The
dependency on the instantiation order is true in any case due to the
execution-model of gem5, so we leave it as is. Also note that the
global ranom generator is not thread safe at this point.
Regressions using the memtest, TrafficGen or any Ruby tester are
affected and will be updated accordingly.
This patch removes unecessary retries that happened when the bus layer
itself was no longer busy, but the the peer was not yet ready. Instead
of sending a retry that will inevitably not succeed, the bus now
silenty waits until the peer sends a retry.
Support full-block writes directly rather than requiring RMW:
* a cache line is allocated in the cache upon receipt of a
WriteInvalidateReq, not the WriteInvalidateResp.
* only top-level caches allocate the line; the others just pass
the request along and invalidate as necessary.
* to close a timing window between the *Req and the *Resp, a new
metadata bit tracks whether another cache has read a copy of
the new line before the writeback to memory.
This patch fixes a bug in the cache port where the retry flag was
reset too early, allowing new requests to arrive before the retry was
actually sent, but with the event already scheduled. This caused a
deadlock in the interactions with the O3 LSQ.
The patche fixes the underlying issue by shifting the resetting of the
flag to be done by the event that also calls sendRetry(). The patch
also tidies up the flow control in recvTimingReq and ensures that we
also check if we already have a retry outstanding.
Previously, they were treated so much like loads that they could stall
at the head of the ROB. Now they are always treated like L1 hits.
If they actually miss, a new request is created at the L1 and tracked
from the MSHRs there if necessary (i.e. if it didn't coalesce with
an existing outstanding load).
If a set of LL/SC requests contend on the same cache block we
can get into a situation where CPUs will deadlock if they expect
a failed SC to supply them data. This case happens where 3 or
more cores are contending for a cache block using LL/SC and the system
is configured where 2 cores are connected to a local bus and the
third is connected to a remote bus. If a core on the local bus
sends an SCUpgrade and the core on the remote bus sends and SCUpgrade
they will race to see who will win the SC access. In the meantime
if the other core appends a read to one of the SCUpgrades it will expect
to be supplied data by that SCUpgrade transaction. If it happens that
the SCUpgrade that was picked to supply the data is failed, it will
drop the appended request for data and never respond, leaving the requesting
core to deadlock. This patch makes all SC's behave as normal stores to
prevent this case but still makes sure to check whether it can perform
the update.
This patch prunes unused values, and also unifies how the values are
defined (not using an enum for ALPHA), aligning the use of int vs Addr
etc.
The patch also removes the duplication of PageBytes/PageShift and
VMPageSize/LogVMPageSize. For all ISAs the two pairs had identical
values and the latter has been removed.
The Index type defined as typedef int64 does not really provide any help
since in most places we use primitive types instead of Index. Also, the name
Index is very generic that it does not merit being used as a typename.
This patch is the final patch in a series of patches. The aim of the series
is to make ruby more configurable than it was. More specifically, the
connections between controllers are not at all possible (unless one is ready
to make significant changes to the coherence protocol). Moreover the buffers
themselves are magically connected to the network inside the slicc code.
These connections are not part of the configuration file.
This patch makes changes so that these connections will now be made in the
python configuration files associated with the protocols. This requires
each state machine to expose the message buffers it uses for input and output.
So, the patch makes these buffers configurable members of the machines.
The patch drops the slicc code that usd to connect these buffers to the
network. Now these buffers are exposed to the python configuration system
as Master and Slave ports. In the configuration files, any master port
can be connected any slave port. The file pyobject.cc has been modified to
take care of allocating the actual message buffer. This is inline with how
other port connections work.
A later changeset changes the file src/python/swig/pyobject.cc to include
a header file that includes a header file generated at build time depending
on the PROTOCOL in use. Since NULL ISA was not specifying any protocol,
this resulted in compilation problems. Hence, the changeset.
The namespace Message conflicts with the Message data type used extensively
in Ruby. Since Ruby is being moved to the same Master/Slave ports based
configuration style as the rest of gem5, this conflict needs to be resolved.
Hence, the namespace is being renamed to ProtoMessage.
There are two changes this patch makes to the way configurable members of a
state machine are specified in SLICC. The first change is that the data
member declarations will need to be separated by a semi-colon instead of a
comma. Secondly, the default value to be assigned would now use SLICC's
assignment operator i.e. ':='.
This patch changes the grammar for SLICC so as to remove some of the
redundant / duplicate rules. In particular rules for object/variable
declaration and class member declaration have been unified. Similarly, the
rules for a general function and a class method have been unified.
One more change is in the priority of two rules. The first rule is on
declaring a function with all the params typed and named. The second rule is
on declaring a function with all the params only typed. Earlier the second
rule had a higher priority. Now the first rule has a higher priority.
This patch enables the use of page tables that are stored in system memory
and respect x86 specification, in SE mode. It defines an architectural
page table for x86 as a MultiLevelPageTable class and puts a placeholder
class for other ISAs page tables, giving the possibility for future
implementation.
This patch defines a multi-level page table class that stores the page table in
system memory, consistent with ISA specifications. In this way, cpu models that
use the actual hardware to execute (e.g. KvmCPU), are able to traverse the page
table.
This patch ensures the cycle check is still valid even restoring from
a checkpoint. In this case the DRAMSim2 cycle count is relative to the
startTick rather than 0.
This patch fixes a bug in the DRAM controller address decoding. In
cases where the DRAM burst size (e.g. 32 bytes in a rank with a single
LPDDR3 x32) was smaller than the channel interleaving size
(e.g. systems with a 64-byte cache line) one address bit effectively
got used as a channel bit when it should have been a low-order column
bit.
This patch adds a notion of "columns per stripe", and more clearly
deals with the low-order column bits and high-order column bits. The
patch also relaxes the granularity check such that it is possible to
use interleaving granularities other than the cache line size.
The patch also adds a missing M5_CLASS_VAR_USED to the tCK member as
it is only used in the debug build for now.
When a cacheline is written back to a lower-level cache,
tags->insertBlock() sets various status parameters. However these
status bits were cleared immediately after calling. This patch makes
it so that these status fields are not cleared by moving them outside
of the tags->insertBlock() call.
this patch implements a new tags class that uses a random replacement policy.
these tags prefer to evict invalid blocks first, if none are available a
replacement candidate is chosen at random.
this patch factors out the common code in the LRU class and creates a new
abstract class: the BaseSetAssoc class. any set associative tag class must
implement the functionality related to the actual replacement policy in the
following methods:
accessBlock()
findVictim()
insertBlock()
invalidate()
This patch adds a DRAMPower flag to enable off-line DRAM power
analysis using the DRAMPower tool. A new DRAMPower flag is added
and a follow-on patch adds a Python script to post-process the output
and order it based on time stamps.
The long-term goal is to link DRAMPower as a library and provide the
commands through function calls to the model rather than first
printing and then parsing the commands. At the moment it is also up to
the user to ensure that the same DRAM configuration is used by the
gem5 controller model and DRAMPower.
This patch adds the index of the bank and rank as a field so that we can
determine the identity of a given bank (reference or pointer) for the
power tracing. We also grab the opportunity of cleaning up the
arguments used for identifying the bank when activating.
Using '== true' in a boolean expression is totally redundant,
and using '== false' is pretty verbose (and arguably less
readable in most cases) compared to '!'.
It's somewhat of a pet peeve, perhaps, but I had some time
waiting for some tests to run and decided to clean these up.
Unfortunately, SLICC appears not to have the '!' operator,
so I had to leave the '== false' tests in the SLICC code.
This patch makes a more firm connection between the DDR3-1600
configuration and the corresponding datasheet, and also adds a
DDR3-2133 and a DDR4-2400 configuration. At the moment there is also
an ongoing effort to align the choice of datasheets to what is
available in DRAMPower.
This patch extends the current timing parameters with the DRAM cycle
time. This is needed as the DRAMPower tool expects timestamps in DRAM
cycles. At the moment we could get away with doing this in a
post-processing step as the DRAMPower execution is separate from the
simulation run. However, in the long run we want the tool to be called
during the simulation, and then the cycle time is needed.
This patch adds the basic ingredients for a precharge all operation,
to be used in conjunction with DRAM power modelling.
Currently we do not try and apply any cleverness when precharging all
banks, thus even if only a single bank is open we use PREA as opposed
to PRE. At the moment we only have a single tRP (tRPpb), and do not
model the slightly longer all-bank precharge constraint (tRPab).
This patch adds the tRTP timing constraint, governing the minimum time
between a read command and a precharge. Default values are provided
for the existing DRAM types.
This patch merges the two control paths used to estimate the latency
and update the bank state. As a result of this merging the computation
is now in one place only, and should be easier to follow as it is all
done in absolute (rather than relative) time.
As part of this change, the scheduling is also refined to ensure that
we look at a sensible estimate of the bank ready time in choosing the
next request. The bank latency stat is removed as it ends up being
misleading when the DRAM access code gets evaluated ahead of time (due
to the eagerness of waking the model up for scheduling the next
request).
This patch adds the write recovery time to the DRAM timing
constraints, and changes the current tRASDoneAt to a more generic
preAllowedAt, capturing when a precharge is allowed to take place.
The part of the DRAM access code that accounts for the precharge and
activate constraints is updated accordingly.
This patch adds power states to the controller. These states and the
transitions can be used together with the Micron power model. As a
more elaborate use-case, the transitions can be used to drive the
DRAMPower tool.
At the moment, the power-down modes are not used, and this patch
simply serves to capture the idle, auto refresh and active modes. The
patch adds a third state machine that interacts with the refresh state
machine.
This patch adds a state machine for the refresh scheduling to
ensure that no accesses are allowed while the refresh is in progress,
and that all banks are propely precharged.
As part of this change, the precharging of banks of broken out into a
method of its own, making is similar to how activations are dealt
with. The idle accounting is also updated to ensure that the refresh
duration is not added to the time that the DRAM is in the idle state
with all banks precharged.
This patch changes the read/write event loop to use a single event
(nextReqEvent), along with a state variable, thus joining the two
control flows. This change makes it easier to follow the state
transitions, and control what happens when.
With the new loop we modify the overly conservative switching times
such that the write-to-read switch allows bank preparation to happen
in parallel with the bus turn around. Similarly, the read-to-write
switch uses the introduced tRTW constraint.
This patch squashes prefetch requests from downstream caches,
so that they do not steal cachelines away from caches closer
to the cpu. It was originally coded by Mitch Hayenga and
modified by Aasheesh Kolli.
Splits the CommMonitor trace_file parameter into three parameters. Previously,
the trace was only enabled if the trace_file parameter was set, and would be
written to this file. This patch adds in a trace_enable and trace_compress
parameter to the CommMonitor.
No trace is generated if trace_enable is set to False. If it is set to True, the
trace is written to a file based on the name of the SimObject in the simulation
hierarchy. For example, system.cluster.il1_commmonitor.trc. This filename can be
overridden by additionally specifying a file name to the trace_file parameter
(more on this later).
The trace_compress parameter will append .gz to any filename if set to True.
This enables compression of the generated traces. If the file name already ends
in .gz, then no changes are made.
The trace_file parameter will override the name set by the trace_enable
parameter. In the case that the specified name does not end in .gz but
trace_compress is set to true, .gz is appended to the supplied file name.
This never actually worked since it was printing out only a word
of the cache block and not the entire thing and doubly didn't work
csprintf overrides the %#x specifier and assumes a char* array is
actually a string.
Upon aggregating records, serialize system's cache-block size, as the
cache-block size can be different when restoring from a checkpoint. This way,
we can correctly read all records when restoring from a checkpoints, even if
the cache-block size is different.
Note, that it is only possible to restore from a checkpoint if the
desired cache-block size is smaller or equal to the cache-block size
when the checkpoint was taken; we can split one larger request into
multiple small ones, but it is not reliable to do the opposite.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
As of now, the enqueue statement can take in any number of 'pairs' as
argument. But we only use the pair in which latency is the key. This
latency is allowed to be either a fixed integer or a member variable of
controller in which the expression appears. This patch drops the use of pairs
in an enqueue statement. Instead, an expression is allowed which will be
interpreted to be the latency of the enqueue. This expression can anything
allowed by slicc including a constant integer or a member variable.
This patch adds stats for tracking the number of reads/writes per bus
turn around, and also adds hysteresis to the write-to-read switching
to ensure that the queue does not oscilate around the low threshold.
This patch renames the not-so-simple SimpleDRAM to a more suitable
DRAMCtrl. The name change is intended to ensure that we do not send
the wrong message (although the "simple" in SimpleDRAM was originally
intended as in cleverly simple, or elegant).
As the DRAM controller modelling work is being presented at ISPASS'14
our hope is that a broader audience will use the model in the future.
--HG--
rename : src/mem/SimpleDRAM.py => src/mem/DRAMCtrl.py
rename : src/mem/simple_dram.cc => src/mem/dram_ctrl.cc
rename : src/mem/simple_dram.hh => src/mem/dram_ctrl.hh
Make the default memory type DDR3-1600 x64, and use the open-adaptive
page policy. This change is aiming to ensure that users by default are
using a realistic memory system.
This patch adds a basic starvation-prevention mechanism where a DRAM
page is forced to close after a certain number of accesses. The limit
is combined with the open and open-adaptive page policy and if reached
causes an auto-precharge.
This patch changes the triggering condition for the write draining
such that we grab the opportunity to issue writes if there are no
reads waiting (as opposed to waiting for the writes to reach the high
threshold). As a result, we potentially drain some of the writes in read
idle periods (if any).
A low threshold is added to be able to control how many write bursts
are kept in the memory controller queue (acting as on-chip storage).
The high and low thresholds are updated to sensible values for a 32/64
size write buffer. Note that the thresholds should be adjusted along
with the queue sizes.
This patch also adds some basic initialisation sanity checks and moves
part of the initialisation to the constructor.
This patch adds the row bits to the name of the address mapping
schemes to make it more clear that all the current schemes places the
row bits as the most significant bits.
This patch moves the Ruby-related debug flags to the ruby
sub-directory, and also removes the state SConsopts that add the
no-longer-used NO_VECTOR_BOUNDS_CHECK.
Each consumer object maintains a set of tick values when the object is supposed
to wakeup and do some processing. As of now, the object accesses this set both
when scheduling a wakeup event and when the object actually wakes up. The set
is accessed during wakeup to remove the current tick value from the set. This
functionality is now being moved to the scheduling function where ticks are
removed at a later time.
This helps in configuring the network interfaces from the python script and
these objects no longer rely on the network object for the timing information.
Piobus was recently added to se scripts for ruby so that the interrupt
controller can be connected to something (required since the interrupt
controller sends address range messages). This patch removes the piobus
and instead, the pio port of ruby port will now ignore the range change
messages in se mode.
This patch fixes an assert condition that is not true at all
times. There are valid situations that arise in dual-core
dual-workload runs where the assert condition is false. The function
call following the assert however needs to be called only when the
condition is true (a block cannot be invalidated in the tags structure
if has not been allocated in the structure, and the tempBlock is never
allocated). Hence the 'assert' has been replaced with an 'if'.
Couple of users observed segmentation fault when the simulator tries to
register the statistical variable m_IncompleteTimes. It seems that there
is some problem with the initialization of these variables when allocated
in the constructor.
Currently, the interrupt controller in x86 is connected to the io bus
directly. Therefore the packets between the io devices and the interrupt
controller do not go through ruby. This patch changes ruby port so that
these packets arrive at the ruby port first, which then routes them to their
destination. Note that the patch does not make these packets go through the
ruby network. That would happen in a subsequent patch.
This patch simplfies the retry logic in the RubyPort, avoiding
redundant attributes, and enforcing more stringent checks on the
interactions with the normal ports. The patch also simplifies the
routing done by the RubyPort, using the port identifiers instead of a
heavy-weight sender state.
The patch also fixes a bug in the sending of responses from PIO
ports. Previously these responses bypassed the queue in the queued
port, and ignored the return value, potentially leading to response
packets being lost.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Code in two of the functions was exactly the same. This patch moves
this code to a new function which is called from the two functions
mentioned initially.
At several places, there are functions that take a cycle value as input
and performs some computation. Along with each such function, another
function was being defined that simply added one more cycle to input and
computed the same function. This patch removes this second copy of the
function. Places where these functions were being called have been updated
to use the original function with argument being current cycle + 1.
Two files had been incorrectly named with a .cache suffix.
--HG--
rename : src/mem/protocol/MESI_Three_Level-L0.cache => src/mem/protocol/MESI_Three_Level-L0cache.sm
rename : src/mem/protocol/MESI_Three_Level-L1.cache => src/mem/protocol/MESI_Three_Level-L1cache.sm
