This patch introduces a few subclasses to the CoherentXBar and
NoncoherentXBar to distinguish the different uses in the system. We
use the crossbar in a wide range of places: interfacing cores to the
L2, as a system interconnect, connecting I/O and peripherals,
etc. Needless to say, these crossbars have very different performance,
and the clock frequency alone is not enough to distinguish these
scenarios.
Instead of trying to capture every possible case, this patch
introduces dedicated subclasses for the three primary use-cases:
L2XBar, SystemXBar and IOXbar. More can be added if needed, and the
defaults can be overridden.
This patch changes how the MMU and table walkers are created such that
a single port is used to connect the MMU and the TLBs to the memory
system. Previously two ports were needed as there are two table walker
objects (stage one and stage two), and they both had a port. Now the
port itself is moved to the Stage2MMU, and each TableWalker is simply
using the port from the parent.
By using the same port we also remove the need for having an
additional crossbar joining the two ports before the walker cache or
the L2. This simplifies the creation of the CPU cache topology in
BaseCPU.py considerably. Moreover, for naming and symmetry reasons,
the TLB walker port is connected through the stage-one table walker
thus making the naming identical to x86. Along the same line, we use
the stage-one table walker to generate the master id that is used by
all TLB-related requests.
Now, prior to the renaming, the instruction requests the exact amount of
registers it will need, and the rename_map decides whether the instruction is
allowed to proceed or not.
This patch fixes a long-standing isue with the port flow
control. Before this patch the retry mechanism was shared between all
different packet classes. As a result, a snoop response could get
stuck behind a request waiting for a retry, even if the send/recv
functions were split. This caused message-dependent deadlocks in
stress-test scenarios.
The patch splits the retry into one per packet (message) class. Thus,
sendTimingReq has a corresponding recvReqRetry, sendTimingResp has
recvRespRetry etc. Most of the changes to the code involve simply
clarifying what type of request a specific object was accepting.
The biggest change in functionality is in the cache downstream packet
queue, facing the memory. This queue was shared by requests and snoop
responses, and it is now split into two queues, each with their own
flow control, but the same physical MasterPort. These changes fixes
the previously seen deadlocks.
Have the traffic generator add its masterID as the PC address to the
requests. That way, prefetchers (and other components) that use a PC
for request classification will see per-tester streams of requests.
This enables us to test strided prefetchers with the memchecker, too.
To be able to use the TrafficGen in a system with caches we need to
allow it to sink incoming snoop requests. By default the master port
panics, so silently ignore any snoops.
The MemTest class really only tests false sharing, and as such there
was a lot of old cruft that could be removed. This patch cleans up the
tester, and also makes it more clear what the assumptions are. As part
of this simplification the reference functional memory is also
removed.
The regression configs using MemTest are updated to reflect the
changes, and the stats will be bumped in a separate patch. The example
config will be updated in a separate patch due to more extensive
re-work.
In a follow-on patch a new tester will be introduced that uses the
MemChecker to implement true sharing.
The TLB-related code is generally architecture dependent and should
live in the arch directory to signify that.
--HG--
rename : src/sim/BaseTLB.py => src/arch/generic/BaseTLB.py
rename : src/sim/tlb.cc => src/arch/generic/tlb.cc
rename : src/sim/tlb.hh => src/arch/generic/tlb.hh
This patch changes how the timing CPU deals with processing responses,
always scheduling an event, even if it is for the current tick. This
helps to avoid situations where a new request shows up before a
response is finished in the crossbar, and also is more in line with
any realistic behaviour.
While the IsFirstMicroop flag exists it was only occasionally used in the ARM
instructions that gem5 microOps and therefore couldn't be relied on to be correct.
This patch tidies up how we create and set the fields of a Request. In
essence it tries to use the constructor where possible (as opposed to
setPhys and setVirt), thus avoiding spreading the information across a
number of locations. In fact, setPhys is made private as part of this
patch, and a number of places where we callede setVirt instead uses
the appropriate constructor.
The ppCommit should notify the attached listener every time the cpu commits
a microop or non microcoded insturction. The listener can then decide
whether it will process only the last microop (eg. SimPoint probe).
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Minor was reporting the data cache access as ".inst" accesses.
This just switches the MasterPortID to dataMasterPortId.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Only the instruction address is actually checked, so there's no need to check
repeatedly while we're working through the microops of a macroop and that's
not changing.
This patch fixes a case where a store in Minor's store buffer never
leaves the store buffer as it is pre-maturely counted as having been
issued, leading to the store buffer idling.
LSQ::StoreBuffer::numUnissuedAccesses should count the number of accesses
either in memory, or still in the store buffer after being completed.
For stores which are also barriers, the store will stay in the store
buffer for a cycle after it is completed and will be cleaned up by the
barrier clearing code (to ensure that barriers are completed in-order).
To acheive this, numUnissuedAccesses is not decremented when a store-barrier
is issued to memory, but when its barrier effect is cleared.
Without this patch, the correct behaviour happens when a memory transaction
is immediately accepted, but not if it needs a retry.
In case the memory subsystem sends a combined response with invalidate
(e.g. ReadRespWithInvalidate), we cannot ignore the invalidate part
of the response.
If we were to ignore the invalidate part, under certain circumstances
this effectively leads to reordering of loads to the same address
which is not permitted under any memory consistency model implemented
in gem5.
Consider the case where a later load's address is computed before an
earlier load in program order, and is therefore sent to the memory
subsystem first. At some point the earlier load's address is computed
and in doing so correctly marks the later load as a
possibleLoadViolation. In the meantime some other node writes and
sends invalidations to all other nodes. The invalidation races with
the later load's ReadResp, and arrives before ReadResp and is
deferred. Upon receipt of the ReadResp, the response is changed to
ReadRespWithInvalidate, and sent to the CPU. If we ignore the
invalidate part of the packet, we let the later load read the old
value of the address. Eventually the earlier load's ReadResp arrives,
but with new data. As there was no invalidate snoop (sunk into the
ReadRespWithInvalidate), and if we did not process the invalidate of
the ReadRespWithInvalidate, we obtain a load reordering.
A similar scenario can be constructed where the earlier load's address
is computed after ReadRespWithInvalidate arrives for the younger
load. In this case hitExternalSnoop needs to be set to true on the
ReadRespWithInvalidate, so that upon knowing the address of the
earlier load, checkViolations will cause the later load to be
squashed.
Finally we must account for the case where both loads are sent to the
memory subsystem (reordered), a snoop invalidate arrives and correctly
sets the later loads fault to ReExec. However, before the CPU
processes the fault, the later load's ReadResp arrives and the
writeback discards the outstanding fault. We must add a check to
ensure that we do not skip any unprocessed faults.
Move the packet deallocations in the O3 CPU so that the completeDataAccess
deals only with the LSQ specific parts and the generic recvTimingResp frees the
packet in all other cases.
This patch simplifies how we deal with dynamically allocated data in
the packet, always assuming that it is array allocated, and hence
should be array deallocated (delete[] as opposed to delete). The only
uses of dataDynamic was in the Ruby testers.
The ARRAY_DATA flag in the packet is removed accordingly. No
defragmentation of the flags is done at this point, leaving a gap in
the bit masks.
As the last part the patch, it renames dataDynamicArray to dataDynamic.
This patch takes a first step in tightening up how we use the data
pointer in write packets. A const getter is added for the pointer
itself (getConstPtr), and a number of member functions are also made
const accordingly. In a range of places throughout the memory system
the new member is used.
The patch also removes the unused isReadWrite function.
This patch removes the parameter that enables bypassing the null check
in the Packet::getPtr method. A number of call sites assume the value
to be non-null.
The one odd case is the RubyTester, which issues zero-sized
prefetches(!), and despite being reads they had no valid data
pointer. This is now fixed, but the size oddity remains (unless anyone
object or has any good suggestions).
Finally, in the Ruby Sequencer, appropriate checks are made for flush
packets as they have no valid data pointer.
This patch adds methods in KvmCPU model to handle KVM exits caused by syscall
instructions and page faults. These types of exits will be encountered if
KvmCPU is run in SE mode.
Another churn to clean up undefined behaviour, mostly ARM, but some
parts also touching the generic part of the code base.
Most of the fixes are simply ensuring that proper intialisation. One
of the more subtle changes is the return type of the sign-extension,
which is changed to uint64_t. This is to avoid shifting negative
values (undefined behaviour) in the ISA code.
Mwait works as follows:
1. A cpu monitors an address of interest (monitor instruction)
2. A cpu calls mwait - this loads the cache line into that cpu's cache.
3. The cpu goes to sleep.
4. When another processor requests write permission for the line, it is
evicted from the sleeping cpu's cache. This eviction is forwarded to the
sleeping cpu, which then wakes up.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Fixes a bug where Minor drains in the midst of committing a
conditional store.
While committing a conditional store, lastCommitWasEndOfMacroop is true
(from the previous instruction) as we still haven't finished the conditional
store. If a drain occurs before the cache response, Minor would check just
lastCommitWasEndOfMacroop, which was true, and set drainState=DrainHaltFetch,
which increases the streamSeqNum. This caused the conditional store to be
squashed when the memory responded and it completed. However, to the memory
the store succeeded, while to the instruction sequence it never occurred.
In the case of an LLSC, the instruction sequence will replay the squashed
STREX, which will fail as the cache is no longer in LLSC. Then the
instruction sequence will loop back to a LDREX, which receives the updated
(incorrect) value.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
It is possible for the O3 CPU to consider itself drained and
later have a squashed instruction perform a writeback. This
patch re-adds tracking of in-flight instructions to prevent
falsely signaling a drained event.
IEW did not check the instQueue and memDepUnit to ensure
they were drained. This caused issues when drainSanityCheck()
did check those structures after asserting IEW was drained.
This patch fixes a bug where a completing load or store which is also a
barrier can push a barrier into the store buffer without first checking
that there is a free slot.
The bug was not fatal but would print a warning that the store buffer
was full when inserting.
This patch takes quite a large step in transitioning from the ad-hoc
RefCountingPtr to the c++11 shared_ptr by adopting its use for all
Faults. There are no changes in behaviour, and the code modifications
are mostly just replacing "new" with "make_shared".
This patch transitions the o3 MemDepEntry from the ad-hoc
RefCountingPtr to the c++11 shared_ptr. There are no changes in
behaviour, and the code modifications are mainly replacing "new" with
"make_shared".
This changeset adds probe points that can be used to implement PMU
counters for CPU stats. The following probes are supported:
* BaseCPU::ppCycles / Cycles
* BaseCPU::ppRetiredInsts / RetiredInsts
* BaseCPU::ppRetiredLoads / RetiredLoads
* BaseCPU::ppRetiredStores / RetiredStores
* BaseCPU::ppRetiredBranches RetiredBranches
This changeset adds probe points that can be used to implement PMU
counters for branch predictor stats. The following probes are
supported:
* BPRedUnit::ppBranches / Branches
* BPRedUnit::ppMisses / Misses
The Ozone CPU is now very much out of date and completely
non-functional, with no one actively working on restoring it. It is a
source of confusion for new users who attempt to use it before
realizing its current state. RIP
This patch optimises the passing of StaticInstPtr by avoiding copying
the reference-counting pointer. This avoids first incrementing and
then decrementing the reference-counting pointer.
Fix a number few minor issues to please gcc 4.9.1. Removing the
'-fuse-linker-plugin' flag means no libraries are part of the LTO
process, but hopefully this is an acceptable loss, as the flag causes
issues on a lot of systems (only certain combinations of gcc, ld and
ar work).
