This patch subsumes the PREFETCH_SNOOP_SQUASH flag with the more
generic BLOCK_CACHED flag. Future patches implementing cache eviction
messages can use the BLOCK_CACHED flag in almost the same manner as
hardware prefetches use the PREFETCH_SNOOP_SQUASH flag. The
PREFTECH_SNOOP_FLAG is set if the prefetch target is found in the tags
or the MSHRs in any state, so we are simply replacing calls to
setPrefetchSquashed() with setBlockCached(). The case of where the
prefetch target is found in the writeback MSHRs of upper level caches
continues to be covered by the MEM_INHIBIT flag.
Currently if there are shell special characters in a
command-line argument, you can't copy and paste the
echoed command line onto a shell prompt because the
characters aren't quoted properly. This patch fixes
that problem.
When using gem5 as a slave simulator, it will not advance the
clock on its own and depends on the master simulator calling
simulate(). This new option lets us use the Python scripts
to do all the configuration while stopping short of actually
simulating anything.
This patch accomplishes two things:
1. Makes simulate()'s GlobalSimLoopExitEvent a singleton reused
across calls. This is slightly more efficient than recreating
it every time.
2. Gives callers to simulate() (especially other simulators) a
foolproof way of knowing that the simulation period ended
successfully by hitting the limit event. They can call
getLimitEvent() and compare it to the return
value of simulate().
This change was motivated by an ongoing effort to integrate gem5
and SST, with SST as the master sim and gem5 as the slave sim.
A recent changeset of mine (http://repo.gem5.org/gem5/rev/4cfe55719da5)
inadvertently fixed a bug in the Minor CPU model which caused it to treat
software prefetches as regular loads. Prior to this changeset, Minor
did an ad-hoc generation of memory commands that left out the PF check;
because it now uses the common code that the other CPU models use,
it generates prefetches properly. These stat changes reflect the fact
that the Minor model now issues SoftPFReqs.
Add a set of scripts to automatically test checkpointing in the
regression framework. The checkpointing tests are similar to the
switcheroo tests, but instead of switching between CPUs, they
checkpoint the system and restore from the checkpoint again. This is
done at regular intervals, typically while booting Linux.
The implementation is fairly straight forward, with the exception that
we have to work around gem5's inability to restore from a checkpoint
after a system has been instantiated. We work around this by forking
off child processes that does the actual simulation and never
instantiate a system in the parent process unless a maximum checkpoint
count is reached (in which case we just simulate the system to
completion in the parent).
Checkpoint testing is currently only enabled 32- and 64-bit ARM
systems using atomic CPUs.
Note: An unfortunate side-effect of forking is that every new process
will overwrite the stats and terminal output from the previous
process. This means that the output directory only contains data from
the last checkpoint.
This patch adds a random option to memtest.py which allows the user to
easily test valid random tree topologies. The patch also adds a
wrapper script to run soak tests using the newly introduced option.
We also adjust the progress interval and progress limit check to make
the output less noisy, and avoid false positives.
Bring on the pain.
This patch adds a new PIO-accessible GICv2m shim. This shim has a PIO
slave port on one side, and SPI 'wires' on the other. It accepts MSIs
from the system and triggers SPIs on the GIC. It is configurable with
a number of frames, each of which has a number of SPIs and a base SPI
offset.
A Linux driver for GICv2m is available upstream.
This patch removes the code that added this magic register. A
follow-up patch provides a GICv2m MSI shim that gives the same
functionality in a standard ARM system architecture way.
This patch enables users to speficy --os-type on the command
line. This option is used to take specific actions for an OS type,
such as changing the kernel command line. This patch is part of the
Android KitKat enablement.
Fix erroneous message format for fatal error.
Previously, code did not have type indicator (% instead of %d).
Also removed redundant fatal check.
Ran modified sweep.py with in range and out of range values to test.
The CommMonitor by default only allows memory traces to be gathered in
timing mode. This patch allows memory traces to be gathered in atomic
mode if all one needs is a functional trace of memory addresses used
and timing information is of a secondary concern.
For some reason we were checking mshr->hasTargets() even though
we had already called mshr->getTarget() unconditionally earlier
in the same function (which asserts if there are no targets).
Get rid of this useless check, and while we're at it get rid
of the redundant call to mshr->getTarget(), since we still have
the value saved in a local var.
Refactor the way that specific MemCmd values are generated for packets.
The new approach is a little more elegant in that we assign the right
value up front, and it's also more amenable to non-heap-allocated
Packet objects.
Also replaced the code in the Minor model that was still doing it the
ad-hoc way.
This is basically a refinement of http://repo.gem5.org/gem5/rev/711eb0e64249.
The 'if (writebacks.size)' check was redundant, because
writeBuffer.findMatches() would return false if the
writebacks list was empty.
Also renamed 'mshr' to 'wb_entry' in this context since
we are pointing at a writebuffer entry and not an MSHR
(even though it's the same C++ class).
This patch modifies FSConfig.py to look for 'android' only in disk
image name. Before this patch, 'android' was searched in full
disk path.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
The variable is used in only one place and a whole new function setNextStatus()
has been defined just to compute the value of the variable. Instead of calling
the function, the value is now computed in the loop that preceded the function
call.
This patch changes all the DPRINTF messages in the cache to use
'%#llx' every time a packet address is printed. The inclusion of '#'
ensures '0x' is prepended, and since the address type is a uint64_t %x
really should be %llx.
This patch fixes a rather subtle issue in the sending of MSHR requests
in the cache, where the logic previously did not check for conflicts
between the MSRH queue and the write queue when requests were not
ready. The correct thing to do is to always check, since not having a
ready MSHR does not guarantee that there is no conflict.
The underlying problem seems to have slipped past due to the symmetric
timings used for the write queue and MSHR queue. However, with the
recent timing changes the bug caused regressions to fail.
This patch changes the valid-bytes start/end to a proper byte
mask. With the changes in timing introduced in previous patches there
are more packets waiting in queues, and there are regressions using
the checker CPU failing due to non-contigous read data being found in
the various cache queues.
This patch also adds some more comments explaining what is going on,
and adds the fourth and missing case to Packet::checkFunctional.
By default, the packet queue is ordered by the ticks of the to-be-sent
packages. With the recent modifications of packages sinking their header time
when their resposne leaves the caches, there could be cases of MSHR targets
being allocated and ordered A, B, but their responses being sent out in the
order B,A. This led to inconsistencies in bus traffic, in particular the snoop
filter observing first a ReadExResp and later a ReadRespWithInv. Logically,
these were ordered the other way around behind the MSHR, but due to the timing
adjustments when inserting into the PacketQueue, they were sent out in the
wrong order on the bus, confusing the snoop filter.
This patch adds a flag (off by default) such that these special cases can
request in-order insertion into the packet queue, which might offset timing
slighty. This is expected to occur rarely and not affect timing results.
This patch makes the caches and memory controllers consume the delay
that is annotated to a packet by the crossbar. Previously many
components simply threw these delays away. Note that the devices still
do not pay for these delays.
This patch introduces a few subclasses to the CoherentXBar and
NoncoherentXBar to distinguish the different uses in the system. We
use the crossbar in a wide range of places: interfacing cores to the
L2, as a system interconnect, connecting I/O and peripherals,
etc. Needless to say, these crossbars have very different performance,
and the clock frequency alone is not enough to distinguish these
scenarios.
Instead of trying to capture every possible case, this patch
introduces dedicated subclasses for the three primary use-cases:
L2XBar, SystemXBar and IOXbar. More can be added if needed, and the
defaults can be overridden.
This patch introduces latencies in crossbar that were neglected
before. In particular, it adds three parameters in crossbar model:
front_end_latency, forward_latency, and response_latency. Along with
these parameters, three corresponding members are added:
frontEndLatency, forwardLatency, and responseLatency. The coherent
crossbar has an additional snoop_response_latency.
The latency of the request path through the xbar is set as
--> frontEndLatency + forwardLatency
In case the snoop filter is enabled, the request path latency is charged
also by look-up latency of the snoop filter.
--> frontEndLatency + SF(lookupLatency) + forwardLatency.
The latency of the response path through the xbar is set instead as
--> responseLatency.
In case of snoop response, if the response is treated as a normal response
the latency associated is again
--> responseLatency;
If instead it is forwarded as snoop response we add an additional variable
+ snoopResponseLatency
and the latency associated is
--> snoopResponseLatency;
Furthermore, this patch lets the crossbar progress on the next clock
edge after an unused retry, changing the time the crossbar considers
itself busy after sending a retry that was not acted upon.
The ARM PL011 UART model didn't clear and raise interrupts
correctly. This changeset rewrites the whole interrupt handling and
makes it both simpler and fixes several cases where the correct
interrupts weren't raised or cleared. Additionally, it cleans up many
other aspects of the code.
This patch changes how the MMU and table walkers are created such that
a single port is used to connect the MMU and the TLBs to the memory
system. Previously two ports were needed as there are two table walker
objects (stage one and stage two), and they both had a port. Now the
port itself is moved to the Stage2MMU, and each TableWalker is simply
using the port from the parent.
By using the same port we also remove the need for having an
additional crossbar joining the two ports before the walker cache or
the L2. This simplifies the creation of the CPU cache topology in
BaseCPU.py considerably. Moreover, for naming and symmetry reasons,
the TLB walker port is connected through the stage-one table walker
thus making the naming identical to x86. Along the same line, we use
the stage-one table walker to generate the master id that is used by
all TLB-related requests.
Now, prior to the renaming, the instruction requests the exact amount of
registers it will need, and the rename_map decides whether the instruction is
allowed to proceed or not.
