This patch makes a more firm connection between the DDR3-1600
configuration and the corresponding datasheet, and also adds a
DDR3-2133 and a DDR4-2400 configuration. At the moment there is also
an ongoing effort to align the choice of datasheets to what is
available in DRAMPower.
This patch extends the current timing parameters with the DRAM cycle
time. This is needed as the DRAMPower tool expects timestamps in DRAM
cycles. At the moment we could get away with doing this in a
post-processing step as the DRAMPower execution is separate from the
simulation run. However, in the long run we want the tool to be called
during the simulation, and then the cycle time is needed.
This patch adds the basic ingredients for a precharge all operation,
to be used in conjunction with DRAM power modelling.
Currently we do not try and apply any cleverness when precharging all
banks, thus even if only a single bank is open we use PREA as opposed
to PRE. At the moment we only have a single tRP (tRPpb), and do not
model the slightly longer all-bank precharge constraint (tRPab).
This patch adds the tRTP timing constraint, governing the minimum time
between a read command and a precharge. Default values are provided
for the existing DRAM types.
This patch merges the two control paths used to estimate the latency
and update the bank state. As a result of this merging the computation
is now in one place only, and should be easier to follow as it is all
done in absolute (rather than relative) time.
As part of this change, the scheduling is also refined to ensure that
we look at a sensible estimate of the bank ready time in choosing the
next request. The bank latency stat is removed as it ends up being
misleading when the DRAM access code gets evaluated ahead of time (due
to the eagerness of waking the model up for scheduling the next
request).
This patch adds the write recovery time to the DRAM timing
constraints, and changes the current tRASDoneAt to a more generic
preAllowedAt, capturing when a precharge is allowed to take place.
The part of the DRAM access code that accounts for the precharge and
activate constraints is updated accordingly.
This patch adds power states to the controller. These states and the
transitions can be used together with the Micron power model. As a
more elaborate use-case, the transitions can be used to drive the
DRAMPower tool.
At the moment, the power-down modes are not used, and this patch
simply serves to capture the idle, auto refresh and active modes. The
patch adds a third state machine that interacts with the refresh state
machine.
This patch adds a state machine for the refresh scheduling to
ensure that no accesses are allowed while the refresh is in progress,
and that all banks are propely precharged.
As part of this change, the precharging of banks of broken out into a
method of its own, making is similar to how activations are dealt
with. The idle accounting is also updated to ensure that the refresh
duration is not added to the time that the DRAM is in the idle state
with all banks precharged.
This patch changes the read/write event loop to use a single event
(nextReqEvent), along with a state variable, thus joining the two
control flows. This change makes it easier to follow the state
transitions, and control what happens when.
With the new loop we modify the overly conservative switching times
such that the write-to-read switch allows bank preparation to happen
in parallel with the bus turn around. Similarly, the read-to-write
switch uses the introduced tRTW constraint.
This patch adds a the member function StaticInst::printFlags to allow all
of an instruction's flags to be printed without using the individual
is... member functions or resorting to exposing the 'flags' vector
It also replaces the enum definition StaticInst::Flags with a
Python-generated enumeration and adds to the enum generation mechanism
in src/python/m5/params.py to allow Enums to be placed in namespaces
other than Enums or, alternatively, in wrapper structs allowing them to
be inherited by other classes (so populating that class's name-space
with the enumeration element names).
This patch encompasses several interrelated and interdependent changes
to the ISA generation step. The end goal is to reduce the size of the
generated compilation units for instruction execution and decoding so
that batch compilation can proceed with all CPUs active without
exhausting physical memory.
The ISA parser (src/arch/isa_parser.py) has been improved so that it can
accept 'split [output_type];' directives at the top level of the grammar
and 'split(output_type)' python calls within 'exec {{ ... }}' blocks.
This has the effect of "splitting" the files into smaller compilation
units. I use air-quotes around "splitting" because the files themselves
are not split, but preprocessing directives are inserted to have the same
effect.
Architecturally, the ISA parser has had some changes in how it works.
In general, it emits code sooner. It doesn't generate per-CPU files,
and instead defers to the C preprocessor to create the duplicate copies
for each CPU type. Likewise there are more files emitted and the C
preprocessor does more substitution that used to be done by the ISA parser.
Finally, the build system (SCons) needs to be able to cope with a
dynamic list of source files coming out of the ISA parser. The changes
to the SCons{cript,truct} files support this. In broad strokes, the
targets requested on the command line are hidden from SCons until all
the build dependencies are determined, otherwise it would try, realize
it can't reach the goal, and terminate in failure. Since build steps
(i.e. running the ISA parser) must be taken to determine the file list,
several new build stages have been inserted at the very start of the
build. First, the build dependencies from the ISA parser will be emitted
to arch/$ISA/generated/inc.d, which is then read by a new SCons builder
to finalize the dependencies. (Once inc.d exists, the ISA parser will not
need to be run to complete this step.) Once the dependencies are known,
the 'Environments' are made by the makeEnv() function. This function used
to be called before the build began but now happens during the build.
It is easy to see that this step is quite slow; this is a known issue
and it's important to realize that it was already slow, but there was
no obvious cause to attribute it to since nothing was displayed to the
terminal. Since new steps that used to be performed serially are now in a
potentially-parallel build phase, the pathname handling in the SCons scripts
has been tightened up to deal with chdir() race conditions. In general,
pathnames are computed earlier and more likely to be stored, passed around,
and processed as absolute paths rather than relative paths. In the end,
some of these issues had to be fixed by inserting serializing dependencies
in the build.
Minor note:
For the null ISA, we just provide a dummy inc.d so SCons is never
compelled to try to generate it. While it seems slightly wrong to have
anything in src/arch/*/generated (i.e. a non-generated 'generated' file),
it's by far the simplest solution.
The unproxy code for Parent.any can generate a circular reference
in certain situations with classes hierarchies like those in ClockDomain.py.
This patch solves this by marking ouself as visited to make sure the
search does not resolve to a self-reference.
The ARM TLBs have a bootUncacheability flag used to make some loads
and stores become uncacheable when booting in FS mode. Later the
flag is cleared to let those loads and stores operate as normal. When
doing a takeOverFrom(), this flag's state is not preserved and is
momentarily reset until the CPSR is touched. On single core runs this
is a non-issue. On multi-core runs this can lead to crashes on the O3
CPU model from the following series of events:
1) takeOverFrom executed to switch from Atomic -> O3
2) All bootUncacheability flags are reset to true
3) Core2 tries to execute a load covered by bootUncacheability, it
is flagged as uncacheable
4) Core2's load needs to replay due to a pipeline flush
3) Core1 core does an action on CPSR
4) The handling code for CPSR then checks all other cores
to determine if bootUncacheability can be set to false
5) Asynchronously set bootUncacheability on all cores to false
6) Core2 replays load previously set as uncacheable and notices
it is now flagged as cacheable, leads to a panic.
This patch implements takeOverFrom() functionality for the ARM TLBs
to preserve flag values when switching from atomic -> detailed.
For the o3, add instruction mix (OpClass) histogram at commit (stats
also already collected at issue). For the simple CPUs we add a
histogram of executed instructions
This patch squashes prefetch requests from downstream caches,
so that they do not steal cachelines away from caches closer
to the cpu. It was originally coded by Mitch Hayenga and
modified by Aasheesh Kolli.
This source for stats binds an object and a method / function from the object
to a stats object. This allows pulling out stats from object methods without
needing to go through a global, or static shim.
Syntax is somewhat unpleasant, but the templates and method pointer type
specification were quite tricky. Interface is very clean though; and similar
to .functor
Allow the specification of a socket ID for every core that is reflected in the
MPIDR field in ARM systems. This allows studying multi-socket / cluster
systems with ARM CPUs.
Splits the CommMonitor trace_file parameter into three parameters. Previously,
the trace was only enabled if the trace_file parameter was set, and would be
written to this file. This patch adds in a trace_enable and trace_compress
parameter to the CommMonitor.
No trace is generated if trace_enable is set to False. If it is set to True, the
trace is written to a file based on the name of the SimObject in the simulation
hierarchy. For example, system.cluster.il1_commmonitor.trc. This filename can be
overridden by additionally specifying a file name to the trace_file parameter
(more on this later).
The trace_compress parameter will append .gz to any filename if set to True.
This enables compression of the generated traces. If the file name already ends
in .gz, then no changes are made.
The trace_file parameter will override the name set by the trace_enable
parameter. In the case that the specified name does not end in .gz but
trace_compress is set to true, .gz is appended to the supplied file name.
Unimplemented miscregs for the generic timer were guarded by panics
in arm/isa.cc which can be tripped by the O3 model if it speculatively
executes a wrong path containing a mrs instruction with a bad miscreg
index. These registers were flagged as implemented and accessible.
This patch changes the miscreg info bit vector to flag them as
unimplemented and inaccessible. In this case, and UndefinedInst
fault will be generated if the register access is not trapped
by a hypervisor.
This patch changes the default pixel clock to effectively generate
1080p resolution at 60 frames per second. It is dependent upon the
kernel device tree file using the specified resolution / display
string in the comments.
This is a quick hack to communicate a greater number of CPUs to a guest OS via
the ARM A9 SCU config register. Some OSes (Linux) just look at the bottom field
to count CPUs and with a small change can look at bits [3:0] to learn about up
to 16 CPUs.
Very much unsupported (and contains warning messages as such) but useful for
running 8 core sims without hardwiring CPU count in the guest OS.
With (upcoming) separate compilation, they are useless. Only
link-time optimization could re-inline them, but ideally
feedback-directed optimization would choose to do so only for
profitable (i.e. common) instructions.
Very rarely does anyone ever mess with PLY code, and when
such a need arises, the developer can reenable this flag in
their working tree.
This will eliminate the "generating LALR tables" message
during compilation and temporary parser.out file as well.
The MicroMemOp class generates the disassembly for both integer
and floating point instructions, but it would always print its
first operand as an integer register without considering that the
op may be a floating instruction in which case a float register
should be displayed instead.
In the O3 LSQ, data read/written is printed out in DPRINTFs. However,
the data field is treated as a character string with a null terminated.
However the data field is not encoded this way. This patch removes
that possibility by removing the data part of the print.
This never actually worked since it was printing out only a word
of the cache block and not the entire thing and doubly didn't work
csprintf overrides the %#x specifier and assumes a char* array is
actually a string.
O3CPU has a compile-time maximum width set in o3/impl.hh, but checking
the configuration against this limit was not implemented anywhere
except for fetch. Configuring a wider pipe than the limit can silently
cause various issues during the simulation. This patch adds the proper
checking in the constructor of the various pipeline stages.
Without this declaration, new clangs will complain about this value
being unused. It has no explicit use in the codebase, but it can be
useful to turn on all debugging flags while in a debugger to greatly
increase simulator verbosity.
