This patch adds a typical (leaning towards fast) LPDDR3 configuration
based on publically available data. As expected, it looks very similar
to the LPDDR2-S4 configuration, only with a slightly lower burst time.
This patch adapts the existing LPDDR2 configuration to make use of the
multi-channel functionality. Thus, to get a x64 interface two
controllers should be instantiated using the makeMultiChannel method.
The page size and ranks are also adapted to better suit with a typical
LPDDR2 part.
This patch removes the explicit memset as it is redundant and causes
the simulator to touch the entire space, forcing the host system to
allocate the pages.
Anonymous pages are mapped on the first access, and the page-fault
handler is responsible for zeroing them. Thus, the pages are still
zeroed, but we avoid touching the entire allocated space which enables
us to use much larger memory sizes as long as not all the memory is
actually used.
This patch simplifies the usage of the packet trace encoder/decoder by
attempting to automatically generating the packet proto definitions in
case they cannot be found.
This patch changes how the streams are created to avoid the size
limitation on the coded streams. As we only read/write a single
message at a time, there is never any message larger than a few
bytes. However, the coded stream eventually complains that its
internal counter reaches 64+ MByte if the total file size exceeds this
value.
Based on suggestions in the protobuf discussion forums, the coded
stream is now created for every message that is read/written. The
result is that the internal byte count never goes about tens of bytes,
and we can read/write any size file that the underlying file I/O can
handle.
This patch changes the type of the hash function for BasicBlockRanges
to match the original definition of the templatized type. Without
this, clang raises a warning and combined with the "-Werror" flag this
causes compilation to fail.
This is the x86 version of the ARM changeset baa17ba80e06. In case an
instruction has been squashed by the o3 cpu, this patch allows page
table walker to avoid carrying out a pending translation that the
instruction requested for.
Currently call and return instructions are marked as IsCall and IsReturn. Thus, the
branch predictor does not use RAS for these instructions. Similarly, the number of
function calls that took place is recorded as 0. This patch marks these instructions
as they should be.
Currently all the integer microops are marked as IntAluOp and the floating
point microops are marked as FloatAddOp. This patch adds support for marking
different microops differently. Now IntMultOp, IntDivOp, FloatDivOp,
FloatMultOp, FloatCvtOp, FloatSqrtOp classes will be used as well. This will
help in providing different latencies for different op class.
The option was not being passed to directory controllers for the protocols
MOESI_CMP_token and MOESI_CMP_directory. This was resulting in an error
while instantiating the directory controller as it tries to access the
wrong type of memory.
This patch changes the way cache statistics are collected in ruby.
As of now, there is separate entity called CacheProfiler which holds
statistical variables for caches. The CacheMemory class defines different
functions for accessing the CacheProfiler. These functions are then invoked
in the .sm files. I find this approach opaque and prone to error. Secondly,
we probably should not be paying the cost of a function call for recording
statistics.
Instead, this patch allows for accessing statistical variables in the
.sm files. The collection would become transparent. Secondly, it would happen
in place, so no function calls. The patch also removes the CacheProfiler class.
--HG--
rename : src/mem/slicc/ast/InfixOperatorExprAST.py => src/mem/slicc/ast/OperatorExprAST.py
having separate params for the local/globalHistoryBits and the
local/globalPredictorSize can lead to inconsistencies if they
are not carefully set. this patch dervies the number of bits
necessary to index into the local/global predictors based on
their size.
the value of the localHistoryTableSize for the ARM O3 CPU has been
increased to 1024 from 64, which is more accurate for an A15 based
on some correlation against A15 hardware.
The CpuPort class was removed before the KVM patches were committed,
which means that the KVM interface currently doesn't compile. This
changeset adds the BaseKvmCPU::KVMCpuPort class which derives from
MasterPort. This class is used on the data and instruction ports
instead of the old CpuPort.
Changeset 5ca6098b9560 accidentally broke the m5 utility. This
changeset adds the missing co-processor call used to trigger the
pseudo-op in ARM mode and fixes an alignment issue that caused some
pseudo-ops to leave thumb mode.
This changeset adds a 'numInsts' stat to the KVM-based CPU. It also
cleans up the variable names in kvmRun to make the distinction between
host cycles and estimated simulated cycles clearer. As a bonus
feature, it also fixes a warning (unreferenced variable) when
compiling in fast mode.
Add a debug print (when the Checkpoint debug flag is set) on serialize
and unserialize. Additionally, dump the KVM state before
serializing. The KVM state isn't dumped after unserializing since the
state is loaded lazily on the next KVM entry.
Device accesses are normally uncacheable. This change probably doesn't
make any difference since we normally disable caching when KVM is
active. However, there might be devices that check this, so we'd
better enable this flag to be safe.
The vsyscall address for gettimeofday is 0xffffffffff600000ul. The offset
therefore should be 0x0 instead of 0x410. This can be cross checked with
the file sysdeps/unix/sysv/linux/x86_64/gettimeofday.c in source of glibc.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This fixes missing mem-type arguments to makeLinuxAlphaRubySystem and
makeLinuxX86System after a recent changeset allowing mem-type to be
configured via options missed fixing these calls.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
The existing implementation can read uninitialized data or stale information
from the cached PageTable entries.
1) Add a valid bit for the cache entries. Simply using zero for the virtual
address to signify invalid entries is not sufficient. Speculative, wrong-path
accesses frequently access page zero. The current implementation would return
a uninitialized TLB entry when address zero was accessed and the PageTable
cache entry was invalid.
2) When unmapping/mapping/remaping a page, invalidate the corresponding
PageTable cache entry if one already exists.
The 'lret' instruction reloads instruction pointer and code segment from the
stack and then pops them. But the popping part is missing from the current
implementation. This caused incorrect behavior in some code related to the
Fiasco OS. Microops are being added to rectify the behavior of the instruction.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Due to recent changes to clocking system in Ruby and the way Ruby restores
state from a checkpoint, garnet was failing to run from a checkpointed state.
The problem is that Ruby resets the time to zero while warming up the caches.
If any component records a local copy of the time (read calls curCycle())
before the simulation has started, then that component will not operate until
that time is reached. In the context of this particular patch, the Garnet
Network class calls curCycle() at multiple places. Any non-operational
component can block in requests in the memory system, which the system
interprets as a deadlock. This patch makes changes so that Garnet can
successfully run from checkpointed state.
It adds a globally visible time at which the actual execution started. This
time is initialized in RubySystem::startup() function. This variable is only
meant for components with in Ruby. This replaces the private variable that
was maintained within Garnet since it is not possible to figure out the
correct time when the value of this variable can be set.
The patch also does away with all cases where curCycle() is called with in
some Ruby component before the system has actually started executing. This
is required due to the quirky manner in which ruby restores from a checkpoint.
This patch adds an address mapping scheme where the channel
interleaving takes place on a cache line granularity. It is similar to
the existing RaBaChCo that interleaves on a DRAM page, but should give
higher performance when there is less locality in the address
stream.
This patch changes the slightly ambigious names used for the address
mapping scheme to be more descriptive, and actually spell out what
they do. With this patch we also open up for adding more flavours of
open- and close-type mappings, i.e. interleaving across channels with
the open map.
This patch enables the use of the generator behaviours outside the
TrafficGen module. This is useful e.g. to allow packet replay modes
for other devices in the system without having to replace them with a
TrafficGen in the configuration files.
This change also enables more specific behaviours to be composed as
specific modules, e.g. BaseBandModem can use a number of generators
and have application-specific parameters based around a specific set
of generators.
This patch enables selection of the memory controller class through a
mem-type command-line option. Behind the scenes, this option is
treated much like the cpu-type, and a similar framework is used to
resolve the valid options, and translate the short-hand description to
a valid class.
The regression scripts are updated with a hardcoded memory class for
the moment. The best solution going forward is probably to get the
memory out of the makeSystem functions, but Ruby complicates things as
it does not connect the memory controller to the membus.
--HG--
rename : configs/common/CpuConfig.py => configs/common/MemConfig.py
This patch adds a WideIO 200 MHz configuration that can be used as a
baseline to compare with DDRx and LPDDRx. Note that it is a single
channel and that it should be replicated 4 times. It is based on
publically available information and attempts to capture an envisioned
8 Gbit single-die part (i.e. without TSVs).
This patch provides useful printouts throughut the memory system. This
includes pretty-printed cache tags and function call messages
(call-stack like).
This patch changes the SimpleTimingPort and RubyPort to panic on
inhibited requests as this should never happen in either of the
cases. The SimpleTimingPort is only used for the I/O devices PIO port
and the DMA devices config port and should thus never see an inhibited
request. Similarly, the SimpleTimingPort is also used for the
MessagePort in x86, and there should also not be any cases where the
port sees an inhibited request.
