- ack assumes that the direction flag in eflags is clear when
assigning two structures. It is implemented by a call to a built-in
function which is like memcpy but needs the flag to be clear
otherwise rubish is copied. This patch fixes the kernel entries.
- When the cpu halts, the interrupts are enable so the cpu may be
woken up. When the interrupt handler returns but another interrupt
is available it is also serviced immediately. This is not a problem
per-se. It only slightly breaks time accounting as idle accounted is
for the kernel time in the interrupt handler.
- As the big kernel lock is lock/unlocked in the smp branch in the
time acounting functions as they are called exactly at the places
we need to take the lock) this leads to a deadlock.
- we make sure that once the interrupt handler returns from the nested
trap, the interrupts are disabled. This means that only one
interrupt is serviced after idle is interrupted.
- this requires the loop in apic timer calibration to keep reenabling
the interrupts. I admit it is a little bit hackish (one line),
however, this code is a stupid corner case at the boot time.
Hopefully it does not matter too much.
IPC changes:
- receive() is changed to take an additional parameter, which is a pointer to
a status code.
- The status code is filled in by the kernel to provide additional information
to the caller. For now, the kernel only fills in the IPC call used by the
sender.
Syslib changes:
- sef_receive() has been split into sef_receive() (with the original semantics)
and sef_receive_status() which exposes the status code to userland.
- Ideally, every sys process should gradually switch to sef_receive_status()
and use is_ipc_notify() as a dependable way to check for notify.
- SEF has been modified to use is_ipc_notify() and demonstrate how to use the
new status code.
- before enabling paging VM asks kernel to resize its segments. This
may cause kernel to segfault if APIC is used and an interrupt
happens between this and paging enabled. As these are 2 separate
vmctl calls it is not atomic. This patch fixes this problem. VM does
not ask kernel to resize the segments in a separate call anymore.
The new segments limit is part of the "enable paging" call. It
generalizes this call in such a way that more information can be
passed as need be or the information may be completely different if
another architecture requires this.
- if an exception occurs in kernel and this exception is not handled
in an sane way and the kernel crashes, it also dumps what was loaded
in the general purpose registers exactly at the time of the
exception to help to debug the problem
the kernel. They are not used atm, but having them in trunk allows them
to be easily used when needed. To set a breakpoint that triggers when
the variable foo is written to (the most common use case), one calls:
breakpoint_set(vir2phys((vir_bytes) &foo), 0,
BREAKPOINT_FLAG_MODE_GLOBAL |
BREAKPOINT_FLAG_RW_WRITE |
BREAKPOINT_FLAG_LEN_4);
It can later be disabled using:
breakpoint_set(vir2phys((vir_bytes) &foo), 0,
BREAKPOINT_FLAG_MODE_OFF);
There are some limitations:
- There are at most four breakpoints (hardware limit); the index of the
breakpoint (0-3) is specified as the second parameter of
breakpoint_set.
- The breakpoint exception in the kernel is not handled and causes a
panic; it would be reasonably easy to change this by inspecing DR6,
printing a message, disabling the breakpoint and continuing. However,
in my experience even just a panic can be very useful.
- Breakpoints can be set only in the part of the address space that is
in every page table. It is useful for the kernel, but to use this for
user processes would require saving and restoring the debug registers
as part of the context switch. Although the CPU provides support for
local breakpoints (I implemened this as BREAKPOINT_FLAG_LOCAL) they
only work if task switching is used.
forget about the dirtypde bitmap and WIPEPDE/DONEPDE macros too.
check if mapping happens to already be in place, and if so, don't
reload cr3 (on the account of that mapping, that is).
don't reload cr3 unconditionally.
UPDATING INFO:
20100317:
/usr/src/etc/system.conf updated to ignore default kernel calls: copy
it (or merge it) to /etc/system.conf.
The hello driver (/dev/hello) added to the distribution:
# cd /usr/src/commands/scripts && make clean install
# cd /dev && MAKEDEV hello
KERNEL CHANGES:
- Generic signal handling support. The kernel no longer assumes PM as a signal
manager for every process. The signal manager of a given process can now be
specified in its privilege slot. When a signal has to be delivered, the kernel
performs the lookup and forwards the signal to the appropriate signal manager.
PM is the default signal manager for user processes, RS is the default signal
manager for system processes. To enable ptrace()ing for system processes, it
is sufficient to change the default signal manager to PM. This will temporarily
disable crash recovery, though.
- sys_exit() is now split into sys_exit() (i.e. exit() for system processes,
which generates a self-termination signal), and sys_clear() (i.e. used by PM
to ask the kernel to clear a process slot when a process exits).
- Added a new kernel call (i.e. sys_update()) to swap two process slots and
implement live update.
PM CHANGES:
- Posix signal handling is no longer allowed for system processes. System
signals are split into two fixed categories: termination and non-termination
signals. When a non-termination signaled is processed, PM transforms the signal
into an IPC message and delivers the message to the system process. When a
termination signal is processed, PM terminates the process.
- PM no longer assumes itself as the signal manager for system processes. It now
makes sure that every system signal goes through the kernel before being
actually processes. The kernel will then dispatch the signal to the appropriate
signal manager which may or may not be PM.
SYSLIB CHANGES:
- Simplified SEF init and LU callbacks.
- Added additional predefined SEF callbacks to debug crash recovery and
live update.
- Fixed a temporary ack in the SEF init protocol. SEF init reply is now
completely synchronous.
- Added SEF signal event type to provide a uniform interface for system
processes to deal with signals. A sef_cb_signal_handler() callback is
available for system processes to handle every received signal. A
sef_cb_signal_manager() callback is used by signal managers to process
system signals on behalf of the kernel.
- Fixed a few bugs with memory mapping and DS.
VM CHANGES:
- Page faults and memory requests coming from the kernel are now implemented
using signals.
- Added a new VM call to swap two process slots and implement live update.
- The call is used by RS at update time and in turn invokes the kernel call
sys_update().
RS CHANGES:
- RS has been reworked with a better functional decomposition.
- Better kernel call masks. com.h now defines the set of very basic kernel calls
every system service is allowed to use. This makes system.conf simpler and
easier to maintain. In addition, this guarantees a higher level of isolation
for system libraries that use one or more kernel calls internally (e.g. printf).
- RS is the default signal manager for system processes. By default, RS
intercepts every signal delivered to every system process. This makes crash
recovery possible before bringing PM and friends in the loop.
- RS now supports fast rollback when something goes wrong while initializing
the new version during a live update.
- Live update is now implemented by keeping the two versions side-by-side and
swapping the process slots when the old version is ready to update.
- Crash recovery is now implemented by keeping the two versions side-by-side
and cleaning up the old version only when the recovery process is complete.
DS CHANGES:
- Fixed a bug when the process doing ds_publish() or ds_delete() is not known
by DS.
- Fixed the completely broken support for strings. String publishing is now
implemented in the system library and simply wraps publishing of memory ranges.
Ideally, we should adopt a similar approach for other data types as well.
- Test suite fixed.
DRIVER CHANGES:
- The hello driver has been added to the Minix distribution to demonstrate basic
live update and crash recovery functionalities.
- Other drivers have been adapted to conform the new SEF interface.
swapcontext, and makecontext).
- Fix VM to not erroneously think the stack segment and data segment have
collided when a user-space thread invokes brk().
- Add test51 to test ucontext functionality.
- Add man pages for ucontext system calls.
Move archtypes.h to include/ dir, since several servers require it. Move
fpu.h and stackframe.h to arch-specific header directory. Make source
files and makefiles aware of the new header locations.
-Convert the include directory over to using bsdmake
syntax
-Update/add mkfiles
-Modify install(1) so that it can create symlinks
-Update makefiles to use new install(1) options
-Rename /usr/include/ibm to /usr/include/i386
-Create /usr/include/machine symlink to arch header files
-Move vm_i386.h to its new home in the /usr/include/i386
-Update source files to #include the header files at their
new homes.
-Add new gnu-includes target for building GCC headers
this change
- makes panic() variadic, doing full printf() formatting -
no more NO_NUM, and no more separate printf() statements
needed to print extra info (or something in hex) before panicing
- unifies panic() - same panic() name and usage for everyone -
vm, kernel and rest have different names/syntax currently
in order to implement their own luxuries, but no longer
- throws out the 1st argument, to make source less noisy.
the panic() in syslib retrieves the server name from the kernel
so it should be clear enough who is panicing; e.g.
panic("sigaction failed: %d", errno);
looks like:
at_wini(73130): panic: sigaction failed: 0
syslib:panic.c: stacktrace: 0x74dc 0x2025 0x100a
- throws out report() - printf() is more convenient and powerful
- harmonizes/fixes the use of panic() - there were a few places
that used printf-style formatting (didn't work) and newlines
(messes up the formatting) in panic()
- throws out a few per-server panic() functions
- cleans up a tie-in of tty with panic()
merging printf() and panic() statements to be done incrementally.
process waiting for" logic, which is duplicated a few times in the
kernel. (For a new feature for top.)
Introducing it and throwing out ESRCDIED and EDSTDIED (replaced by
EDEADSRCDST - so we don't have to care which part of the blocking is
failing in system.c) simplifies some code in the kernel and callers that
check for E{DEADSRCDST,ESRCDIED,EDSTDIED}, but don't care about the
difference, a fair bit, and more significantly doesn't duplicate the
'blocked-on' logic.
- as thre are still KERNEL and IDLE entries, time accounting for
kernel and idle time works the same as for any other process
- everytime we stop accounting for the currently running process,
kernel or idle, we read the TSC counter and increment the p_cycles
entry.
- the process cycles inherently include some of the kernel cycles as
we can stop accounting for the process only after we save its
context and we start accounting just before we restore its context
- this assumes that the system does not scale the CPU frequency which
will be true for ... long time ;-)
- we don't need to test this in kernel as we always have interrupts
disabled
- if interrupts are enabled in kernel, it is only at very carefully
chosen places. There are no such places now.
- there are no tasks running, we don't need TASK_PRIVILEGE priviledge anymore
- as there is no ring 1 anymore, there is no need for level0() to call sensitive
code from ring 1 in ring 0
- 286 related macros removed as clean up
- no kernel tasks are runnable
- clock initialization moved to the end of main()
- the rest of the body of clock_task() is moved to bsp_timer_int_handler() as
for now we are going to handle this on the bootstrap cpu. A change later is
possible.
* Userspace change to use the new kernel calls
- _taskcall(SYSTASK...) changed to _kernel_call(...)
- int 32 reused for the kernel calls
- _do_kernel_call() to make the trap to kernel
- kernel_call() to make the actuall kernel call from C using
_do_kernel_call()
- unlike ipc call the kernel call always succeeds as kernel is
always available, however, kernel may return an error
* Kernel side implementation of kernel calls
- the SYSTEm task does not run, only the proc table entry is
preserved
- every data_copy(SYSTEM is no data_copy(KERNEL
- "locking" is an empty operation now as everything runs in
kernel
- sys_task() is replaced by kernel_call() which copies the
message into kernel, dispatches the call to its handler and
finishes by either copying the results back to userspace (if
need be) or by suspending the process because of VM
- suspended processes are later made runnable once the memory
issue is resolved, picked up by the scheduler and only at
this time the call is resumed (in fact restarted) which does
not need to copy the message from userspace as the message
is already saved in the process structure.
- no ned for the vmrestart queue, the scheduler will restart
the system calls
- no special case in do_vmctl(), all requests remove the
RTS_VMREQUEST flag
- copies a mesage from/to userspace without need of translating
addresses
- the assumption is that the address space is installed, i.e. ldt and
cr3 are loaded correctly
- if a pagefault or a general protection occurs while copying from
userland to kernel (or vice versa) and error is returned which gives
the caller a chance to respond in a proper way
- error happens _only_ because of a wrong user pointer if the function
is used correctly
- if the prerequisites of the function do no hold, the function will
most likely fail as the user address becomes random
- switch_address_space() implements a switch of the user address space
for the destination process
- this makes memory of this process easily accessible, e.g. a pointer
valid in the userspace can be used with a little complexity to
access the process's memory
- the switch does not happed only just before we return to userspace,
however, it happens right after we know which process we are going
to schedule. This happens before we start processing the misc flags
of this process so its memory is available
- if the process becomes not runnable while processing the mics flags
we pick a new process and we switch the address space again which
introduces possibly a little bit more overhead, however, it is
hopefully hidden by reducing the overheads when we actually access
the memory
- the syscalls are pretty much just ipc calls, however, sendrec() is
used to implement system task (sys) calls
- sendrec() won't be used anymore for this, therefore ipc calls will
become pure ipc calls
- the system task initialization code does not really need to be part
of the system task process. An earlier initialization in kernel is
cleaner as it does not only initialize the syscalls but also irq
hooks etc.
kernel (sys task). The main reason is that these would have to become
cpu local variables on SMP. Once the system task is not a task but a
genuine part of the kernel there is even less reason to have these
extra variables as proc_ptr will already contain all neccessary
information. In addition converting who_e to the process pointer and
back again all the time will be avoided.
Although proc_ptr will contain all important information, accessing it
as a cpu local variable will be fairly expensive, hence the value
would be assigned to some on stack local variable. Therefore it is
better to add the 'caller' argument to the syscall handlers to pass
the value on stack anyway. It also clearly denotes on who's behalf is
the syscall being executed.
This patch also ANSIfies the syscall function headers.
Last but not least, it also fixes a potential bug in virtual_copy_f()
in case the check is disabled. So far the function in case of a
failure could possible reuse an old who_p in case this function had
not been called from the system task.
virtual_copy_f() takes the caller as a parameter too. In case the
checking is disabled, the caller must be NULL and non NULL if it is
enabled as we must be able to suspend the caller.
Some cases were fixed by declaring the function void, others were fixed
by adding a return <value> statement, thereby avoiding potentially
incorrect behavior (usually in error handling).
Some enum correctness in boot.c.
There is not that much use for it on a single CPU, however, deadlock
between kernel and system task can be delected. Or a runaway loop.
If a kernel gets locked up the timer interrupts don't occure (as all
interrupts are disabled in kernel mode). The only chance is to
interrupt the kernel by a non-maskable interrupt.
This patch generates NMIs using performance counters. It uses the most
widely available performace counters. As the performance counters are
highly model-specific this patch is not guaranteed to work on every
machine. Unfortunately this is also true for KVM :-/ On the other
hand adding this feature for other models is not extremely difficult
and the framework makes it hopefully easy enough.
Depending on the frequency of the CPU an NMI is generated at most
about every 0.5s If the cpu's speed is less then 2Ghz it is generated
at most every 1s. In general an NMI is generated much less often as
the performance counter counts down only if the cpu is not idle.
Therefore the overhead of this feature is fairly minimal even if the
load is high.
Uppon detecting that the kernel is locked up the kernel dumps the
state of the kernel registers and panics.
Local APIC must be enabled for the watchdog to work.
The code is _always_ compiled in, however, it is only enabled if
watchdog=<non-zero> is set in the boot monitor.
One corner case is serial console debugging. As dumping a lot of stuff
to the serial link may take a lot of time, the watchdog does not
detect lockups during this time!!! as it would result in too many
false positives. 10 nmi have to be handled before the lockup is
detected. This means something between ~5s to 10s.
Another corner case is that the watchdog is enabled only after the
paging is enabled as it would be pure madness to try to get it right.
Main changes:
- COW optimization for safecopy.
- safemap, a grant-based interface for sharing memory regions between processes.
- Integration with safemap and complete rework of DS, supporting new data types
natively (labels, memory ranges, memory mapped ranges).
- For further information:
http://wiki.minix3.org/en/SummerOfCode2009/MemoryGrants
Additional changes not included in the original Wu's branch:
- Fixed unhandled case in VM when using COW optimization for safecopy in case
of a block that has already been shared as SMAP.
- Better interface and naming scheme for sys_saferevmap and ds_retrieve_map
calls.
- Better input checking in syslib: check for page alignment when creating
memory mapping grants.
- DS notifies subscribers when an entry is deleted.
- Documented the behavior of indirect grants in case of memory mapping.
- Test suite in /usr/src/test/safeperf|safecopy|safemap|ds/* reworked
and extended.
- Minor fixes and general cleanup.
- TO-DO: Grant ids should be generated and managed the way endpoints are to make
sure grant slots are never misreused.
- if debugging on serial console is enabled typing Q kills the system. It is
handy if the system gets locked up and the timer interrupts still work. Good
for remote debugging.
- NOT_REACHABLE reintroduced and fixed. It should be used for marking code which
is not reachable because the previous code _should_ not return. Such places
are not always obvious
SYSLIB CHANGES:
- SEF framework now supports a new SEF Init request type from RS. 3 different
callbacks are available (init_fresh, init_lu, init_restart) to specify
initialization code when a service starts fresh, starts after a live update,
or restarts.
SYSTEM SERVICE CHANGES:
- Initialization code for system services is now enclosed in a callback SEF will
automatically call at init time. The return code of the callback will
tell RS whether the initialization completed successfully.
- Each init callback can access information passed by RS to initialize. As of
now, each system service has access to the public entries of RS's system process
table to gather all the information required to initialize. This design
eliminates many existing or potential races at boot time and provides a uniform
initialization interface to system services. The same interface will be reused
for the upcoming publish/subscribe model to handle dynamic
registration / deregistration of system services.
VM CHANGES:
- Uniform privilege management for all system services. Every service uses the
same call mask format. For boot services, VM copies the call mask from init
data. For dynamic services, VM still receives the call mask via rs_set_priv
call that will be soon replaced by the upcoming publish/subscribe model.
RS CHANGES:
- The system process table has been reorganized and split into private entries
and public entries. Only the latter ones are exposed to system services.
- VM call masks are now entirely configured in rs/table.c
- RS has now its own slot in the system process table. Only kernel tasks and
user processes not included in the boot image are now left out from the system
process table.
- RS implements the initialization protocol for system services.
- For services in the boot image, RS blocks till initialization is complete and
panics when failure is reported back. Services are initialized in their order of
appearance in the boot image priv table and RS blocks to implements synchronous
initialization for every system service having the flag SF_SYNCH_BOOT set.
- For services started dynamically, the initialization protocol is implemented
as though it were the first ping for the service. In this case, if the
system service fails to report back (or reports failure), RS brings the service
down rather than trying to restart it.
- clean up kernel section of minix/com.h somewhat
- remove ALLOCMEM and VM_ALLOCMEM calls
- remove non-safecopy and minix-vmd support from Inet
- remove SYS_VIRVCOPY and SYS_PHYSVCOPY calls
- remove obsolete segment encoding in SYS_SAFECOPY*
- remove DEVCTL call, svrctl(FSDEVUNMAP), map_driverX
- remove declarations of unimplemented svrctl requests
- remove everything related to swapping to disk
- remove floppysetup.sh
- remove traces of rescue device
- update DESCRIBE.sh with new devices
- some other small changes
- Revise VFS-FS protocol and update VFS/MFS/ISOFS accordingly.
- Clean up MFS by removing old, dead code (backwards compatibility is broken by
the new VFS-FS protocol, anyway) and rewrite other parts. Also, make sure all
functions have proper banners and prototypes.
- VFS should always provide a (syntactically) valid path to the FS; no need for
the FS to do sanity checks when leaving/entering mount points.
- Fix several bugs in MFS:
- Several path lookup bugs in MFS.
- A link can be too big for the path buffer.
- A mountpoint can become inaccessible when the creation of a new inode
fails, because the inode already exists and is a mountpoint.
- Introduce support for supplemental groups.
- Add test 46 to test supplemental group functionality (and removed obsolete
suppl. tests from test 2).
- Clean up VFS (not everything is done yet).
- ISOFS now opens device read-only. This makes the -r flag in the mount command
unnecessary (but will still report to be mounted read-write).
- Introduce PipeFS. PipeFS is a new FS that handles all anonymous and
named pipes. However, named pipes still reside on the (M)FS, as they are part
of the file system on disk. To make this work VFS now has a concept of
'mapped' inodes, which causes read, write, truncate and stat requests to be
redirected to the mapped FS, and all other requests to the original FS.
The old deadlock code was misplaced and unable to deal with asynchronous
IPC primitives (notify and senda) effectively. As an example, the following
sequence of messages allowed the deadlock detection code to
trigger a false positive:
1. A.notify(B)
2. A.receive(B)
3. B.receive(A)
1. B.notify(A)
The solution is to run the deadlock detection routine only when a process is
about to block in mini_send() or mini_receive().
KERNEL CHANGES:
- The kernel only knows about privileges of kernel tasks and the root system
process (now RS).
- Kernel tasks and the root system process are the only processes that are made
schedulable by the kernel at startup. All the other processes in the boot image
don't get their privileges set at startup and are inhibited from running by the
RTS_NO_PRIV flag.
- Removed the assumption on the ordering of processes in the boot image table.
System processes can now appear in any order in the boot image table.
- Privilege ids can now be assigned both statically or dynamically. The kernel
assigns static privilege ids to kernel tasks and the root system process. Each
id is directly derived from the process number.
- User processes now all share the static privilege id of the root user
process (now INIT).
- sys_privctl split: we have more calls now to let RS set privileges for system
processes. SYS_PRIV_ALLOW / SYS_PRIV_DISALLOW are only used to flip the
RTS_NO_PRIV flag and allow / disallow a process from running. SYS_PRIV_SET_SYS /
SYS_PRIV_SET_USER are used to set privileges for a system / user process.
- boot image table flags split: PROC_FULLVM is the only flag that has been
moved out of the privilege flags and is still maintained in the boot image
table. All the other privilege flags are out of the kernel now.
RS CHANGES:
- RS is the only user-space process who gets to run right after in-kernel
startup.
- RS uses the boot image table from the kernel and three additional boot image
info table (priv table, sys table, dev table) to complete the initialization
of the system.
- RS checks that the entries in the priv table match the entries in the boot
image table to make sure that every process in the boot image gets schedulable.
- RS only uses static privilege ids to set privileges for system services in
the boot image.
- RS includes basic memory management support to allocate the boot image buffer
dynamically during initialization. The buffer shall contain the executable
image of all the system services we would like to restart after a crash.
- First step towards decoupling between resource provisioning and resource
requirements in RS: RS must know what resources it needs to restart a process
and what resources it has currently available. This is useful to tradeoff
reliability and resource consumption. When required resources are missing, the
process cannot be restarted. In that case, in the future, a system flag will
tell RS what to do. For example, if CORE_PROC is set, RS should trigger a
system-wide panic because the system can no longer function correctly without
a core system process.
PM CHANGES:
- The process tree built at initialization time is changed to have INIT as root
with pid 0, RS child of INIT and all the system services children of RS. This
is required to make RS in control of all the system services.
- PM no longer registers labels for system services in the boot image. This is
now part of RS's initialization process.
- gas2ack cannot handle all variants of some instructions. Until this issues is
addressed, this patch places a big warning where appropriate. This code is not
supposed to change frequently.
- local APIC timer used as the source of time
- PIC is still used as the hw interrupt controller as we don't have
enough info without ACPI or MPS to set up IO APICs
- remapping of APIC when switching paging on, uses the new mechanism
to tell VM what phys areas to map in kernel's virtual space
- one more step to SMP
based on code by Arun C.
- idle task becomes a pseudo task which is never scheduled. It is never put on
any run queue and never enters userspace. An entry for this task still remains
in the process table for time accounting
- Instead of panicing if there is not process to schedule, pick_proc() returns
NULL which is a signal to put the cpu in an idle state and set everything in
such a way that after receiving and interrupt it looks like idle task was
preempted
- idle task is set non-preemptible to avoid handling in the timer interrupt code
which make userspace scheduling simpler as idle task does not need to be
handled as a special case.
- the gnu .S are compiled with __ASSEMBLY__ macro set which allows us to
conditionaly remove C stuff from the proc.h file when included in assembly
files
- new proc_is_runnable() macro to test whether process is runnable. All tests
whether p_rts_flags == 0 converted to use this macro
- pick_proc() calls removed from enqueue() and dequeue()
- removed the test for recursive calls from pick_proc() as it certainly cannot
be called recursively now
- PREEMPTED flag to mark processes that were preempted by enqueueuing a higher
priority process in enqueue()
- enqueue_head() to enqueue PREEMPTED processes again at the head of their
current priority queue
- NO_QUANTUM flag to block and dequeue processes preempted by timer tick with
exceeded quantum. They need to be enqueued again in schedcheck()
- next_ptr global variable removed
- after a trap to kernel, the code automatically switches to kernel
stack, in the future local to the CPU
- k_reenter variable replaced by a test whether the CS is kernel cs or
not. The information is passed further if needed. Removes a global
variable which would need to be cpu local
- no need for global variables describing the exception or trap
context. This information is kept on stack and a pointer to this
structure is passed to the C code as a single structure
- removed loadedcr3 variable and its use replaced by reading the %cr3
register
- no need to redisable interrupts in restart() as they are already
disabled.
- unified handling of traps that push and don't push errorcode
- removed save() function as the process context is not saved directly
to process table but saved as required by the trap code. Essentially
it means that save() code is inlined everywhere not only in the
exception handling routine
- returning from syscall is more arch independent - it sets the retger
in C
- top of the x86 stack contains the current CPU id and pointer to the
currently scheduled process (the one right interrupted) so the mode
switch code can find where to save the context without need to use
proc_ptr which will be cpu local in the future and therefore
difficult to access in assembler and expensive to access in general
- some more clean up of level0 code. No need to read-back the argument
passed in
%eax from the proc structure. The mode switch code does not clobber
%the general registers and hence we can just call what is in %eax
- many assebly macros in sconst.h as they will be reused by the apic
assembly
- preemption handled in the clock timer interrupt handler, not in the clock task
- more achitecture independent clock timer handling code
- smp ready as each CPU can have its own timer
- the PIC master and slave irq handlers don't pass the irq hook pointer but just
the irq number. It gives a little bit more information to the C handler as the
irq number is not lost
- the irq code path is more achitecture independent. i386 hw interrupts are
called irq and whereever the code is arch independent enough hw_intr_
functions are called to mask/unmask interrupts
- the legacy PIC is not the only possible interrupt controller in the x86 world,
therefore the intr_(un)mask functions were renamed to signal their
functionality explicitly. APIC will add their own.
- masking and unmasking PIC interrupt lines is removed from assembler and all
the functionality is rewriten in C and moved to i8259.c
- interrupt handlers have to unmask the interrupt line if all irq handlers are
done. Assembler does not do it anymore
told to kernel
- makes VM ask the kernel if a certain process is allowed
to map in a range of physical memory (VM rounds it to page
boundaries afterwards - but it's impossible to map anything
smaller otherwise so I assume this is safe, i.e. there won't
be anything else in that page; certainly no regular memory)
- VM permission check cleanup (no more hardcoded calls, less
hardcoded logic, more readable main loop), a loose end left
by GQ
- remove do_copy warning, as the ipc server triggers this but
it's no more harmful than the special cases already excluded
explicitly (VFS, PM, etc).
debugging info on panic: decode segment selectors and descriptors, now moved
to arch-specific part, prototypes added; sanity checking in debug.h made
optional with vmassert().
be used concurrently. pass the function in eax instead; this gets rid
of the global variable. also execute the function directly if we're
already trapped into the kernel.
revert of u32_t endpoint_t to int (some code assumes endpoints are
negative for negative slot numbers).
- allow PM to tell sys_runctl() whether to use delay call feature
- only use this feature in PM for delivering signals - not for exits
- do better error checking in PM on sys_runctl() calls
- rename SIGKREADY to SIGNDELAY
o Support for ptrace T_ATTACH/T_DETACH and T_SYSCALL
o PM signal handling logic should now work properly, even with debuggers
being present
o Asynchronous PM/VFS protocol, full IPC support for senda(), and
AMF_NOREPLY senda() flag
DETAILS
Process stop and delay call handling of PM:
o Added sys_runctl() kernel call with sys_stop() and sys_resume()
aliases, for PM to stop and resume a process
o Added exception for sending/syscall-traced processes to sys_runctl(),
and matching SIGKREADY pseudo-signal to PM
o Fixed PM signal logic to deal with requests from a process after
stopping it (so-called "delay calls"), using the SIGKREADY facility
o Fixed various PM panics due to race conditions with delay calls versus
VFS calls
o Removed special PRIO_STOP priority value
o Added SYS_LOCK RTS kernel flag, to stop an individual process from
running while modifying its process structure
Signal and debugger handling in PM:
o Fixed debugger signals being dropped if a second signal arrives when
the debugger has not retrieved the first one
o Fixed debugger signals being sent to the debugger more than once
o Fixed debugger signals unpausing process in VFS; removed PM_UNPAUSE_TR
protocol message
o Detached debugger signals from general signal logic and from being
blocked on VFS calls, meaning that even VFS can now be traced
o Fixed debugger being unable to receive more than one pending signal in
one process stop
o Fixed signal delivery being delayed needlessly when multiple signals
are pending
o Fixed wait test for tracer, which was returning for children that were
not waited for
o Removed second parallel pending call from PM to VFS for any process
o Fixed process becoming runnable between exec() and debugger trap
o Added support for notifying the debugger before the parent when a
debugged child exits
o Fixed debugger death causing child to remain stopped forever
o Fixed consistently incorrect use of _NSIG
Extensions to ptrace():
o Added T_ATTACH and T_DETACH ptrace request, to attach and detach a
debugger to and from a process
o Added T_SYSCALL ptrace request, to trace system calls
o Added T_SETOPT ptrace request, to set trace options
o Added TO_TRACEFORK trace option, to attach automatically to children
of a traced process
o Added TO_ALTEXEC trace option, to send SIGSTOP instead of SIGTRAP upon
a successful exec() of the tracee
o Extended T_GETUSER ptrace support to allow retrieving a process's priv
structure
o Removed T_STOP ptrace request again, as it does not help implementing
debuggers properly
o Added MINIX3-specific ptrace test (test42)
o Added proper manual page for ptrace(2)
Asynchronous PM/VFS interface:
o Fixed asynchronous messages not being checked when receive() is called
with an endpoint other than ANY
o Added AMF_NOREPLY senda() flag, preventing such messages from
satisfying the receive part of a sendrec()
o Added asynsend3() that takes optional flags; asynsend() is now a
#define passing in 0 as third parameter
o Made PM/VFS protocol asynchronous; reintroduced tell_fs()
o Made PM_BASE request/reply number range unique
o Hacked in a horrible temporary workaround into RS to deal with newly
revealed RS-PM-VFS race condition triangle until VFS is asynchronous
System signal handling:
o Fixed shutdown logic of device drivers; removed old SIGKSTOP signal
o Removed is-superuser check from PM's do_procstat() (aka getsigset())
o Added sigset macros to allow system processes to deal with the full
signal set, rather than just the POSIX subset
Miscellaneous PM fixes:
o Split do_getset into do_get and do_set, merging common code and making
structure clearer
o Fixed setpriority() being able to put to sleep processes using an
invalid parameter, or revive zombie processes
o Made find_proc() global; removed obsolete proc_from_pid()
o Cleanup here and there
Also included:
o Fixed false-positive boot order kernel warning
o Removed last traces of old NOTIFY_FROM code
THINGS OF POSSIBLE INTEREST
o It should now be possible to run PM at any priority, even lower than
user processes
o No assumptions are made about communication speed between PM and VFS,
although communication must be FIFO
o A debugger will now receive incoming debuggee signals at kill time
only; the process may not yet be fully stopped
o A first step has been made towards making the SYSTEM task preemptible
- marks code path that should be unreachable (never executed)
- if hit, panics and reports the problem
- the end of main() marked as such. The SMP changes need some magic with stack
switching before the AP can be started as they need to run on the boot stack
before figuring out what is their own stack. As main() uses the boot stack to,
we need to switch to to the stack of BSP before executing the last part of
main() which needs to be in a separate function so we can jump to it.
Therefore restart() won't be the last call in main() which may be confusing.
The macro can/should be used in other such places too.
- headers use the endpoint_t in syslib.h and the implmentation was using int
instead. Both uses endpoint_t now
- every variable named like proc, proc_nr or proc_nr_e of type endpoint_t has
name proc_ep now
- endpoint_t defined as u32_t not int
- no longer have kernel have its own page table that is loaded
on every kernel entry (trap, interrupt, exception). the primary
purpose is to reduce the number of required reloads.
Result:
- kernel can only access memory of process that was running when
kernel was entered
- kernel must be mapped into every process page table, so traps to
kernel keep working
Problem:
- kernel must often access memory of arbitrary processes (e.g. send
arbitrary processes messages); this can't happen directly any more;
usually because that process' page table isn't loaded at all, sometimes
because that memory isn't mapped in at all, sometimes because it isn't
mapped in read-write.
So:
- kernel must be able to map in memory of any process, in its own
address space.
Implementation:
- VM and kernel share a range of memory in which addresses of
all page tables of all processes are available. This has two purposes:
. Kernel has to know what data to copy in order to map in a range
. Kernel has to know where to write the data in order to map it in
That last point is because kernel has to write in the currently loaded
page table.
- Processes and kernel are separated through segments; kernel segments
haven't changed.
- The kernel keeps the process whose page table is currently loaded
in 'ptproc.'
- If it wants to map in a range of memory, it writes the value of the
page directory entry for that range into the page directory entry
in the currently loaded map. There is a slot reserved for such
purposes. The kernel can then access this memory directly.
- In order to do this, its segment has been increased (and the
segments of processes start where it ends).
- In the pagefault handler, detect if the kernel is doing
'trappable' memory access (i.e. a pagefault isn't a fatal
error) and if so,
- set the saved instruction pointer to phys_copy_fault,
breaking out of phys_copy
- set the saved eax register to the address of the page
fault, both for sanity checking and for checking in
which of the two ranges that phys_copy was called
with the fault occured
- Some boot-time processes do not have their own page table,
and are mapped in with the kernel, and separated with
segments. The kernel detects this using HASPT. If such a
process has to be scheduled, any page table will work and
no page table switch is done.
Major changes in kernel are
- When accessing user processes memory, kernel no longer
explicitly checks before it does so if that memory is OK.
It simply makes the mapping (if necessary), tries to do the
operation, and traps the pagefault if that memory isn't present;
if that happens, the copy function returns EFAULT.
So all of the CHECKRANGE_OR_SUSPEND macros are gone.
- Kernel no longer has to copy/read and parse page tables.
- A message copying optimisation: when messages are copied, and
the recipient isn't mapped in, they are copied into a buffer
in the kernel. This is done in QueueMess. The next time
the recipient is scheduled, this message is copied into
its memory. This happens in schedcheck().
This eliminates the mapping/copying step for messages, and makes
it easier to deliver messages. This eliminates soft_notify.
- Kernel no longer creates a page table at all, so the vm_setbuf
and pagetable writing in memory.c is gone.
Minor changes in kernel are
- ipc_stats thrown out, wasn't used
- misc flags all renamed to MF_*
- NOREC_* macros to enter and leave functions that should not
be called recursively; just sanity checks really
- code to fully decode segment selectors and descriptors
to print on exceptions
- lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
- [ABCD]_INDEX are not used anywhere
- value of *_SELECTOR is now calculated using the *_INDEX value so changing the
index does not break the selector
- TSS is now the last of the global selectors. There will be TSS per CPU on SMP
and the number will vary depending on the maximal supported number of CPUs
configured
- pproc_addr is not neccessary to get the address of a process if we know its
number
- local proc variables in system calls implementation (sys_task) conflicts with
the global proc array of all process, therefore the variable were renamed to
proc_nr as they hold the process number
- a better name for architecture specific init function
- some of x86 init code must execute in protected mode
- prot_init() removed from this function and still called in cstart() Imho this
should be called from the architecture specific assembly not cstart. cstart
perform Minix monitor specific tasks and will be touched once another
bootloader is in use, e.g. booting via tftp, therefore we keep it as is for
now.
- this is a backport from the SMP code which requires this. Merging will be simpler
If an exception happens in kernel while the kernel is booting and no processes
are running yet, saved_proc == NULL and priting any process related information
results in dumping rubish.
This check is mostly useful when debugging kernel stuff. Should _never_ happen
on a production kernel.
This is a backport form the SMP branch. Not required here, it only makes life
for SMP easier. And future merging too.
- filling the IDT is removed from prot_init()
- struct gate_table_s is a public type
- gate_table_pic is a global array as it is used by APIC code too
- idt_copy_vectors() is also global and used by idt_init() as well as
apic_idt_init()
- idt_init() is called right after prot_init() in system_init()
Kernel:
o Remove s_ipc_sendrec, instead using s_ipc_to for all send primitives
o Centralize s_ipc_to bit manipulation,
- disallowing assignment of bits pointing to unused priv structs;
- preventing send-to-self by not setting bit for own priv struct;
- preserving send mask matrix symmetry in all cases
o Add IPC send mask checks to SENDA, which were missing entirely somehow
o Slightly improve IPC stats accounting for SENDA
o Remove SYSTEM from user processes' send mask
o Half-fix the dependency between boot image order and process numbers,
- correcting the table order of the boot processes;
- documenting the order requirement needed for proper send masks;
- warning at boot time if the order is violated
RS:
o Add support in /etc/drivers.conf for servers that talk to user processes,
- disallowing IPC to user processes if no "ipc" field is present
- adding a special "USER" label to explicitly allow IPC to user processes
o Always apply IPC masks when specified; remove -i flag from service(8)
o Use kernel send mask symmetry to delay adding IPC permissions for labels
that do not exist yet, adding them to that label's process upon creation
o Add VM to ipc permissions list for rtl8139 and fxp in drivers.conf
Left to future fixes:
o Removal of the table order vs process numbers dependency altogether,
possibly using per-process send list structures as used for SYSTEM calls
o Proper assignment of send masks to boot processes;
some of the assigned (~0) masks are much wider than necessary
o Proper assignment of IPC send masks for many more servers in drivers.conf
o Removal of the debugging warning about the now legitimate case where RS's
add_forward_ipc cannot find the IPC destination's label yet
give every process a full pagetable by default now.
first step to disabling kernel page table code (processes
might not have page tables -> no address translation).
- ipc checking code in kernel didn't properly catch the
sendrec() to self case; added special case check
- triggered by PM using stock panic() - needs its own _exit()
reported by Joren l'Ami.
now used for printing diagnostic messages through the kernel message
buffer. this lets processes print diagnostics without sending messages
to tty and log directly, simplifying the message protocol a lot and
reducing difficulties with deadlocks and other situations in which
diagnostics are blackholed (e.g. grants don't work). this makes
DIAGNOSTICS(_S), ASYN_DIAGNOSTICS and DIAG_REPL obsolete, although tty
and log still accept the codes for 'old' binaries. This also simplifies
diagnostics in several servers and drivers - only tty needs its own
kputc() now.
. simplifications in vfs, and some effort to get the vnode references
right (consistent) even during shutdown. m_mounted_on is now NULL
for root filesystems (!) (the original and new root), a less awkward
special case than 'm_mounted_on == m_root_node'. root now has exactly
one reference, to root, if no files are open, just like all other
filesystems. m_driver_e is unused.
. introduce FULLVM flag: MEMORY and the initial MFS
get their own full address spaces, making their stacks
and heaps not preallocated (well, freed after VM has
initialized it) and letting them allocate more dynamically.
MEMORY in particular needs this to map in physical memory
using its own page table, without having to allocate.
process is not PREEMPTIBLE (or it's not ready, or there isn't a current
process yet). This fixes a case where a process that isn't
PREEMPTIBLE actually gets preempted. (This solves a race condition
between CLOCK and SYSTEM.)
. read_tsc() in sysutil library saves edx and eax now
. added read_tsc_64() by Antonio Mancina to load tsc into
a 64-bit data type directly
. deleted read_tsc.h in favour of a prototype in <minix/syslib.h>
bugfixes:
SYSTEM:
. removed
rc->p_priv->s_flags = 0;
for the priv struct shared by all user processes in get_priv(). this
should only be done once. doing a SYS_PRIV_USER in sys_privctl()
caused the flags of all user processes to be reset, so they were no
longer PREEMPTIBLE. this happened when RS executed a policy script.
(this broke test1 in the test set)
VFS/MFS:
. chown can change the mode of a file, and chmod arguments are only
part of the full file mode so the full filemode is slightly magic.
changed these calls so that the final modes are returned to VFS, so
that the vnode can be kept up-to-date.
(this broke test11 in the test set)
MFS:
. lookup() checked for sizeof(string) instead of sizeof(user_path),
truncating long path names
(caught by test 23)
. truncate functions neglected to update ctime
(this broke test16)
VFS:
. corner case of an empty filename lookup caused fields of a request
not to be filled in in the lookup functions, not making it clear
that the lookup had failed, causing messages to garbage processes,
causing strange failures.
(caught by test 30)
. trust v_size in vnode when doing reads or writes on non-special
files, truncating i/o where necessary; this is necessary for pipes,
as MFS can't tell when a pipe has been truncated without it being
told explicitly each time.
when the last reader/writer on a pipe closes, tell FS about
the new size using truncate_vn().
(this broke test 25, among others)
. permission check for chdir() had disappeared; added a
forbidden() call
(caught by test 23)
new code, shouldn't change anything:
. introduced RTS_SET, RTS_UNSET, and RTS_ISSET macro's, and their
LOCK variants. These macros set and clear the p_rts_flags field,
causing a lot of duplicated logic like
old_flags = rp->p_rts_flags; /* save value of the flags */
rp->p_rts_flags &= ~NO_PRIV;
if (old_flags != 0 && rp->p_rts_flags == 0) lock_enqueue(rp);
to change into the simpler
RTS_LOCK_UNSET(rp, NO_PRIV);
so the macros take care of calling dequeue() and enqueue() (or lock_*()),
as the case may be). This makes the code a bit more readable and a
bit less fragile.
. removed return code from do_clocktick in CLOCK as it currently
never replies
. removed some debug code from VFS
. fixed grant debug message in device.c
preemptive checks, tests, changes:
. added return code checks of receive() to SYSTEM and CLOCK
. O_TRUNC should never arrive at MFS (added sanity check and removed
O_TRUNC code)
. user_path declared with PATH_MAX+1 to let it be null-terminated
. checks in MFS to see if strings passed by VFS are null-terminated
IS:
. static irq name table thrown out
mainly in the kernel and headers. This split based on work by
Ingmar Alting <iaalting@cs.vu.nl> done for his Minix PowerPC architecture
port.
. kernel does not program the interrupt controller directly, do any
other architecture-dependent operations, or contain assembly any more,
but uses architecture-dependent functions in arch/$(ARCH)/.
. architecture-dependent constants and types defined in arch/$(ARCH)/include.
. <ibm/portio.h> moved to <minix/portio.h>, as they have become, for now,
architecture-independent functions.
. int86, sdevio, readbios, and iopenable are now i386-specific kernel calls
and live in arch/i386/do_* now.
. i386 arch now supports even less 86 code; e.g. mpx86.s and klib86.s have
gone, and 'machine.protected' is gone (and always taken to be 1 in i386).
If 86 support is to return, it should be a new architecture.
. prototypes for the architecture-dependent functions defined in
kernel/arch/$(ARCH)/*.c but used in kernel/ are in kernel/proto.h
. /etc/make.conf included in makefiles and shell scripts that need to
know the building architecture; it defines ARCH=<arch>, currently only
i386.
. some basic per-architecture build support outside of the kernel (lib)
. in clock.c, only dequeue a process if it was ready
. fixes for new include files
files deleted:
. mpx/klib.s - only for choosing between mpx/klib86 and -386
. klib86.s - only for 86
i386-specific files files moved (or arch-dependent stuff moved) to arch/i386/:
. mpx386.s (entry point)
. klib386.s
. sconst.h
. exception.c
. protect.c
. protect.h
. i8269.c
from DIO_REQUEST. Also do_vdevio. Also do_sdevio, but this
function also supports grant id's and offsets.
do_segctl: rename protected to prot.
do_umap: support for GRANT_SEG umap.
do_privctl: support SYS_PRIV_SET_GRANTS, which sets location and size
of in-own-address-space grant table.
do_safecopy: functions to verify and perform 'safe' (grant-based) copies.
implementation functions.
Changed check in system.c to check compile-time-sized bitmap of
kernel calls.
Added SYS_SAFECOPYFROM and SYS_SAFECOPYTO, both mapping to
do_safecopy (that's what sys_call_code is used for).
any number of kernel calls.
Allowed kernel calls are stored in table.c for every image process as a
variably-sized array of allowed calls. This is used to fill the bitmap
of size determined at compile time by the number of kernel calls. This
filling is done by main.c. There is a special call called SYS_ALL_CALLS
which fills the bitmap of allowed calls completely, if that is the only
entry in the array.
instead of keeping a running total of enqueued processes
(because somehow the load average was broken)
. added SI_KPROC_TAB to get a copy of kernel process table from PM, for
a top implementation
. fixed arg to sys_nice() to make it an endpoint, not a slot number
instance numbers, encoded and decoded using macros in <minix/endpoint.h>.
proc number -> endpoint migration
. proc_nr in the interrupt hook is now an endpoint, proc_nr_e.
. m_source for messages and notifies is now an endpoint, instead of
proc number.
. isokendpt() converts an endpoint to a process number, returns
success (but fails if the process number is out of range, the
process slot is not a living process, or the given endpoint
number does not match the endpoint number in the process slot,
indicating an old process).
. okendpt() is the same as isokendpt(), but panic()s if the conversion
fails. This is mainly used for decoding message.m_source endpoints,
and other endpoint numbers in kernel data structures, which should
always be correct.
. if DEBUG_ENABLE_IPC_WARNINGS is enabled, isokendpt() and okendpt()
get passed the __FILE__ and __LINE__ of the calling lines, and
print messages about what is wrong with the endpoint number
(out of range proc, empty proc, or inconsistent endpoint number),
with the caller, making finding where the conversion failed easy
without having to include code for every call to print where things
went wrong. Sometimes this is harmless (wrong arg to a kernel call),
sometimes it's a fatal internal inconsistency (bogus m_source).
. some process table fields have been appended an _e to indicate it's
become and endpoint.
. process endpoint is stored in p_endpoint, without generation number.
it turns out the kernel never needs the generation number, except
when fork()ing, so it's decoded then.
. kernel calls all take endpoints as arguments, not proc numbers.
the one exception is sys_fork(), which needs to know in which slot
to put the child.
via cause_sig() during an exception.
moved lock check configuration to <minix/sys_config.h> instead of
kernel/config.h, because the 'relocking' field in kinfo depends on it.
other prettification: common locking macro, whether lock timing is on or
not.
OUTPUT_PROCS_ARRAY in <minix/config.h>, in that order, terminated by NONE.
log no longer forwards messages to tty itself. This leads to less funny
loops and more robust debug-message handling. Also the list of
processes receiving messages can easily be changed around or disabled by
editing the array (e.g. disable it by changing the array to { NONE }.).
. motd update (ast)
. made /usr/local/man/man* and made them bin-owned (mtree)
(to let bin install there)
. made copyright notice in kernel 1987-2006 (ast)
. added chown -R bin /usr/src so that bin can compile everything
. Also allow receive() to be done from kernel processes, not just
sendrec(). This is because receive()s can't harm the kernel processes,
but are done from the CLOCK task (without sendrec()).
enforced. If a call is denied, this will be kprinted. Please report any such
errors, so that I can adjust the mask before returning errors instead of
warnings.
Wrote CMOS driver. All CMOS code from FS has been removed. Currently the
driver only supports get time calls. Set time is left out as an exercise
for the book readers ... startup scripts were updated because the CMOS driver
is needed early on. (IS got same treatment.) Don't forget to run MAKEDEV cmos
in /dev/, otherwise the driver cannot be loaded.
The user needs to set label=... to choose the driver of his or her choice.
This driver will be mapped onto the controller that is set in controller=...
Minor cleanup of kernel source code (boot image table now is static).
This was caused by a change in the shared driver code. Not log's fault.
Renamed #definitions of driver process numbers, e.g., TTY now is TTY_PROC_NR.
All known (special) processes now have consistent naming scheme. Kernel tasks
don't follow this scheme.
to provide an index (0 .. 31) that is passed in the HARD_INT message when an
interrupt occurs. The NOTIFY_ARG field contains a bitmap with all indexes for
which an interrupt occured.
TTY: select and revive with new notify and FS call back;
kernel: removed old notify code; removed ugly prepare_shutdown timer
kputc: don't send to FS if PRINTF_PROC fails
- reinstalled priority changing, now in sched() and unready()
- reinstalled check on message buffer in sys_call()
- reinstalled check in send masks in sys_call()
- changed do_fork() to get new privilege structure for SYS_PROCs
- removed some processes from boot image---will be dynamically started later
sys_privctl() call to dynamically start servers and drivers.
- Shutdown sequence slightly adjusted: called as watchdog timer to let the
busy sys_abort() call from the PM return first.
- Changed umap_bios() to have more restrictive check: BIOS memory is now
allowed in BIOS_MEM_BEGIN to END (interrupt vectors) and BASE_MEM_TOP
to UPPER_MEM_END. Hopefully this keeps QEMU and Bochs happy.
- fixed bug that caused IDLE to panic (irq hook inconsistency);
- kprintf() now accepts multiple arguments; moved to utility.c;
- prepare_shutdown() signals system processes with SIGKSTOP;
- phys_fill() renamed to phys_memset(), argument order changed;
- kmemset() removed in favor of phys_kmemset();
- kstrncpy() removed in favor of phys_copy();
- katoi, kstrncmp replaced by normal library procedure again;
- rm_irq_handler() interface changed (simply pass hook pointer);
that passes signal map along. This mechanisms is also used for nonuser signals
like SIGKMESS, SIGKSTOP, SIGKSIG.
Revised comments of many system call handlers. Renamed setpriority to nice.
New configuration header file to include/ exclude functionality.
Extracted privileged features from struct proc and create new struct priv.
Renamed various system calls for readability.
copied into was the same size as the source string - it will keep on
filling with zeroes forever. This was a signed/unsigned bug, fixed by
making the kstrncpy argument ssize_t instead of size_t. This bug was
triggered by Chris Young <teddga@earthlink.net>, by dazzling coincedence -
changing OS_VERSION into something with one more character (exactly the
same size as the buffer in the kinfo struct).
Also noticed that the kstrncpy() call didn't null-terminate the strings
if necessary, also fixed.
and the new log driver if enabled.
new usyslogd is started from /usr/etc/rc. New device created by
MAKEDEV.sh. /var/log created by etc/mtree/minix.tree (on root for
now). Made select() slightly more generic, with less code duplication.
Not a really good solution (as it might not catch situations in which this
is caused by another bug), but the forrest of checks necessary might be worse
than this quick fix - because when looking for the cause, I found some other
cases in which the PM would panic as well. See info in bug 2 for details.
Another fix is to delay notification of PM by SYSTASK of signals delivered
internally until after the reply (e.g. of exec()), because the reply would
be messed up otherwise (receiving the notify instead of reply). This caused
SIGTRAP not to be delivered properly with traced processes.
- current and maximum priority per process;
- quantum size and current ticks left per process;
- max number of full quantums in a row allow
(otherwise current priority is decremented)
Removed stop sequence when MINIX is shut down.
Disabled send mask checks --- to be replaced by proper mechanism.
Fixed bug relating to 'shutdown -x'.
Simplified clock accounting of realtime.
Updated Makefiles for mkdept script.
long. This is used to check for interrupts being disabled at the time
of a lock() call, if enabled in config.h. The number of times this
happens is then counted in the kinfo structure. These events (recursive
lockings) lead to nasty race conditions.
The TTY driver now only notifies the IS server about function key event,
but does not tell which keys are pressed. The IS servers queries the TTY
driver to find out about this.
caused interrupts to be reenabled (due to unlock), which caused a race. The
problems were especially visible on slower machines.
* Relocated free memory parsing to process manager. This saved quite some
code at the kernel level. Text size was reduced by about 650 bytes.
* Removed locks for updating the realtime in the clock's main loop and the
get_uptime function. Interrupts are no longer reentrant, so realtime is
immediately updated.
Reduced kernel size by 512KB by moving private buffer into cstart() function.
Replaced assertions with erroneous return values. Removed assertions relating
to isuserp(rp), since all processes should become user processes; system
processes are now treated similar to other processes.
* Removed some variants of the SYS_GETINFO calls from the kernel;
replaced them with new PM and utils libary functionality. Fixed
bugs in utils library that used old get_kenv() variant.
* Implemented a buffer in the kernel to gather random data.
Memory driver periodically checks this for /dev/random.
A better random algorithm can now be implemented in the driver.
Removed SYS_RANDOM; the SYS_GETINFO call is used instead.
* Remove SYS_KMALLOC from the kernel. Memory allocation can now
be done at the process manager with new 'other' library functions.
when lock timing is enabled in minix/config.h.
Added phys_zero() routine to klib386.s that zeroes a range of memory, and
added corresponding system call.
This allowed removing the p_flagarlm timer from the kernel's process table.
Furthermore, I merged p_syncalrm and p_signalrm into p_alarm_timer to save
even more space. Note that processes can no longer have both a signal and
synchronous alarm timer outstanding as of now.
size wraparound), one to see if the size fits in the designated segment.
It seems this check wasn't done. This came to light when trying to pre-check
the users buffer for read() and write() in using the vectored virtual
copy system call in servers/fs/read.c.
and type) are overwritten with newer flags/ arguments. The interface from
within the kernel is lock_notify(). User processes can make a system call with
notify(). NOTIFY fully replaces the old notification mechanism.
The call works. Permission check, restriction of outstanding notifications
to be added. Low level code to make it work from within interrupt handlers
will be added as well.
list of handlers, callable by irqctl system call
. workaround for hanging keyboard bug after shutdown.. if key is pressed
during or after shutdown procedure, keyboard stops working. It looks like
irq 1 gets stuck high if no keyboard reading is done (e.g. because the
irq is masked or tty driver has exited). Workaround is to leave irqs
enabled until the last second, and call shutdown() immediately after the
last driver has stopped (tty task). This way the chance of an unserviced
interrupt occuring is negligible.
