separate the rx thread and tx thread and get rid of the dedicated flag.
dev/ns_gige.cc:
dev/ns_gige.hh:
dev/ns_gige_reg.h:
python/m5/objects/Ethernet.py:
dedicated flag goes away, we have new individual flags for
rx thread and tx thread
dev/sinic.cc:
Virtualize sinic
- The io registers are replicated many times in memory, allowing the NIC to
differentiate among several virtual interfaces.
- On the TX side, this allows multiple CPUs to initiate transmits at the same
time without locking in the software. If a partial packet is transmitted,
then the state machine blocks waiting for that virtual interface to complete
its packet. Then the state machine will move on to the next virtual
interface. The commands are kept in fifo order.
- On the RX side, multiple partial transmits can be simultaneously done.
Though a packet does not deallocate its fifo space until all preceeding
packets in the fifo are deallocated. To enable multiple receives, it
is necessary for each virtual nic to keep its own information about its
progress through the state machine.
dev/sinic.hh:
Virtualize sinic
Receive state must be virtualized since we allow the receipt of packets in
parallel.
dev/sinicreg.hh:
Virtualize sinic
separate rx thread and tx thread
create a soft interrupt and add a command to trigger it.
pad out the reserved bits in the RxDone and TxDone regs
--HG--
extra : convert_revision : c10bb23a46a89ffd1e08866c1f1621cb98069205
dev/ns_gige.cc:
add support for delaying pio writes until the cache access occurs
the only write we delay are for CR_TXE and CR_RXE
dev/sinic.cc:
dev/sinic.hh:
the txPioRequest and rxPioRequest things were more or less bogus
add support for delaying pio writes until the cache access occurs
dev/sinicreg.hh:
Add delay_read and delay_write to the register information struct
for now, we won't delay any reads, and we'll delay the writes that
initiate DMAs
python/m5/objects/Ethernet.py:
add a parameter to delay pio writes until the timing access
actually occurs.
--HG--
extra : convert_revision : 79b18ea2812c2935d7d5ea6eff1f55265114d05d
python/m5/config.py:
Clock should not be a NumericParamValue since math on it can be
ambiguous. (As the comment clearly says.)
--HG--
extra : convert_revision : 74f8ec846c6a980d92e0bf4bf1c7fac73a75b923
python/m5/config.py:
Make Clock a NumericParamValue so you can do math with it
--HG--
extra : convert_revision : 7fa548d1a23c604a31d3ecae3853949b064a1830
can specify either independently.
python/m5/objects/Device.py:
io_bus is split out into pio_bus and dma_bus so that any device
can specify either independently.
dma_bus defaults to point to whatever pio_bus uses.
--HG--
extra : convert_revision : d35d5374d0bf592f6b5df465c05203577b8b8763
losing type information.
python/m5/config.py:
Allow math on CheckedInt-derived ParamValue classes w/o
losing type information.
- Make CheckedInt derive from NumericParamValue, and *not*
multiply inherit from long
- Move CheckedInt bounds check to _check() hook so we can
call it when value is updated (not just in constructor)
python/m5/convert.py:
- make toInteger() return a long, making toLong() unnecessary
- toMemorySize should return long rather than float
--HG--
extra : convert_revision : c1cf5e15b9ff35d9b573dd545e076fe68afef989
interrupts.
dev/sinic.cc:
- The prepareRead function sets all the variables in the register
file that depend on various state bits that change on the fly.
Includes RxDone, RxWait, TxDone, and TxWait
- Use the new register information accessor functions to grab
validity and size information for the read and write functions
- read all registers directly from the register space by offset
and size, not by actual name (less code)
- The side effect of reading the interrupt status (clearing it) now
happens outside the actual chunk of code where the value is loaded.
- Add an iprRead function for when we may want speculative access
to device registers through an ipr or special instruction.
- When RxData or TxData are written, their busy flag is set to
indicate that they have an outstanding transaction.
- The RxHigh and TxLow interrupts are special, they only interrupt
if the rxEmpty or txFull limits were hit
- Move reset to the command register
- Update more registers on reset, clear rxEmpty and txFull
- Data dumps only happen if EthernetData trace flag set
- When a DMA completes, kick the other engine if it was waiting
- implement all of the new interrupts
- serialize the new stuff
dev/sinic.hh:
- Put all registers with their proper size and alignment into
the regs struct so that we can copy multiple at a time.
- Provide accessor functions for accessing the registers with
different sizes.
- Flags to track when the rx fifo hit empty and the tx fifo became
full. These flags are used to determine what to do when below
the watermarks, and are reset when crossing the watermark.
- the txDmaEvent should actually trigger the txDmaDone function
- Add an iprRead function for when we may want speculative access
to device registers through an ipr or special instruction.
- The prepareRead function sets all the variables in the register
file that depend on various state bits that change on the fly.
- add rx_max_intr and dedicated (for dedicated thread) config params
dev/sinicreg.hh:
Add some new registers: Command, RxMaxIntr, RxFifoSize, TxFifoSize,
rename XxThreshold to XxFifoMark
Move Reset to the Command register
Add Thread to the Config register
New interrupts, better names
More info in RxDone and TxDone
Easier access to information on each register (size, read, write, name)
python/m5/objects/Ethernet.py:
Both sinic and nsgige have the dedicated thread
Add a parameter to configure the maximum number for receive
packets per interrupt
--HG--
extra : convert_revision : 407c5a993b6fb17326b4c623ee5d4b25fd69ac80
Create EtherDevBase which both Sinic and NSGigE derive from
bump fifos
drop rx max copy size to 1514 bytes to be friendlier with linux
default interrupt delay is 10us
dev/ns_gige.cc:
Shuffle around parameters to make it easier to find stuff
dev/sinic.cc:
Shuffle around parameters to make it easier to find stuff
rename cycleTime -> clock
dev/sinic.hh:
rename cycleTime -> clock
--HG--
extra : convert_revision : a673bee875e50d083098991aea20972fa8d5b5c7
dev/ns_gige.cc:
stop exposing the m5reg to the configuration stuff and build it
based on exposed flags. Expose dedicated now.
dev/ns_gige.hh:
goodbye m5reg hello dedicated
dev/ns_gige_reg.h:
Flags for the M5REG
--HG--
extra : convert_revision : 11134fe67cdf5291caacf9b3041739c437b983e3
stay fixed even if the path to the binary changes, so the simulation results
are independent of that path.
--HG--
extra : convert_revision : d1109cd284466c14eddc97289908a51e771fc5db
dev/etherdump.cc:
no default parameters anymore they should be in python
python/m5/objects/Ethernet.py:
move the maxlen parameter for EtherDump into python
--HG--
extra : convert_revision : a796353a68907dfeb22059cd3ad536e6e8f60998
For example, 'scons ALPHA_SE/test/opt/quick' will build
ALPHA_SE/m5.opt if necessary and run all the self-identified
"quick" tests on it. Other possibilities:
- Run just test1: scons ALPHA_SE/test/opt/test1
- Run all tests: scons ALPHA_SE/test/opt
- Run all tests on debug build: scons ALPHA_SE/test/debug
- Update test1 reference outputs in m5-test:
scons update_ref=y ALPHA_SE/test/opt/test1
The proper tests will be selected based on the setting
of FULL_SYSTEM, ALPHA_TLASER, etc.
README:
Update directions to use scons-based test invocation.
SConscript:
Return list of generated build environments to SConstruct
so it can associate tests with each of them.
Set 'M5Binary' attribute on each env to record name of
generated binary to be tested.
build/SConstruct:
- Support invoking m5-test tests via scons.
- Add new non-sticky option category, for 'update_ref'.
- Move existing "sticky" option definitions out of
build_dir loop. Someday we can generate help text
from these.
- Make 'CC' and 'CXX' sticky options; use environment vars as
defaults if available.
- Make config builder more scons-y.
python/m5/__init__.py:
Make AddToPath() correctly handle relative path arguments.
Assumes that sys.path[0] has the directory where the current
Python file lives; new m5execfile() function sets this up
properly for exec'd files.
--HG--
extra : convert_revision : 48896688592e210d8e63f96c34e57474853d0e66
from Latency to Tick, and rename max_time to max_tick.
python/m5/objects/Root.py:
sim/root.cc:
Convert type of max_time and progress_interval
from Latency to Tick, and rename max_time to max_tick.
--HG--
extra : convert_revision : 2f2aacf6321c3003a0ce834acd8fb726abf27ce3
build directory instead of being inferred from the name
of the build directory.
Options are passed to C++ via config/*.hh files instead of
via the command line. Build option flags are now always
defined to 0 or 1, so checks must use '#if' rather than
'#ifdef'.
SConscript:
MySQL detection moved to SConstruct.
Add config/*.hh files (via ConfigFile builder).
arch/alpha/alpha_memory.cc:
arch/alpha/ev5.cc:
arch/alpha/ev5.hh:
arch/alpha/isa_traits.hh:
base/fast_alloc.hh:
base/statistics.cc:
base/statistics.hh:
base/stats/events.cc:
base/stats/events.hh:
cpu/base.cc:
cpu/base.hh:
cpu/base_dyn_inst.cc:
cpu/base_dyn_inst.hh:
cpu/exec_context.cc:
cpu/exec_context.hh:
cpu/o3/alpha_cpu.hh:
cpu/o3/alpha_cpu_builder.cc:
cpu/o3/alpha_cpu_impl.hh:
cpu/o3/alpha_dyn_inst.hh:
cpu/o3/alpha_dyn_inst_impl.hh:
cpu/o3/alpha_params.hh:
cpu/o3/commit_impl.hh:
cpu/o3/cpu.cc:
cpu/o3/cpu.hh:
cpu/o3/fetch_impl.hh:
cpu/o3/iew.hh:
cpu/o3/iew_impl.hh:
cpu/o3/regfile.hh:
cpu/o3/rename_impl.hh:
cpu/o3/rob_impl.hh:
cpu/ozone/cpu.hh:
cpu/pc_event.cc:
cpu/simple/cpu.cc:
cpu/simple/cpu.hh:
sim/process.cc:
sim/process.hh:
Convert compile flags from def/undef to 0/1.
Set via #include config/*.hh instead of command line.
arch/alpha/isa_desc:
Convert compile flags from def/undef to 0/1.
Set via #include config/*.hh instead of command line.
Revamp fenv.h support... most of the ugliness is hidden
in base/fenv.hh now.
base/mysql.hh:
Fix typo in #ifndef guard.
build/SConstruct:
Build options are set via a build_options file in the
build directory instead of being inferred from the name
of the build directory.
Options are passed to C++ via config/*.hh files instead of
via the command line.
python/SConscript:
Generate m5_build_env directly from scons options
instead of indirectly via CPPDEFINES.
python/m5/convert.py:
Allow '0' and '1' for booleans.
Rewrite toBool to use dict.
base/fenv.hh:
Revamp <fenv.h> support to make it a compile option
(so we can test w/o it even if it's present) and to
make isa_desc cleaner.
--HG--
extra : convert_revision : 8f97dc11185bef5e1865b3269c7341df8525c9ad
SConscript:
Added more files to compile: dev/pcifake.cc, dev/isa_fake.cc, kern/freebsd/freebsd_system.cc, kern/freebsd/freebsd_events.cc.
arch/alpha/isa_traits.hh:
Added constant for argument register 2 as it is needed by FreebsdSystem::doCalibrateClocks().
cpu/exec_context.hh:
cpu/o3/alpha_cpu.hh:
Replaced htoa()s with gtoh() and htog().
cpu/o3/fetch_impl.hh:
cpu/simple/cpu.cc:
Replaced htoa() with gtoh().
dev/disk_image.cc:
Replaced htoa()s with letoh()s.
dev/ide_ctrl.cc:
Got rid of magic numbers.
Added IdeChannel and IdeRegType type names where necessary.
dev/ide_ctrl.hh:
Got rid of unnecessary macros.
Changed RegType_t to IdeRegType.
Changed bmi_regs to allow accessing registers by name instead of just by array index.
Added IdeChannel enum type to use in place of bool variables which were used to specify IDE channel.
dev/ide_disk.cc:
Rewrote IdeDisk::read and IdeDisk::write functions to specify registers by name instead of indexing through an array.
dev/ide_disk.hh:
Updated command register struct.
dev/ns_gige.cc:
dev/ns_gige.hh:
Made ReadConfig and WriteConfig begin with a lower-case letter.
writeConfig() now takes a pointer to data as a parameter instead of a copy of data.
dev/pciconfigall.cc:
writeConfig() now takes a pointer to data as a parameter instead of a copy of data.
dev/pcidev.cc:
Cleaned up readConfig() and writeConfig() functions.
dev/pcidev.hh:
Added macros to make code that works with the BARs (base adress registers) more readable. writeConfig() now takes a pointer to data.
dev/pcireg.h:
Changed PCIConfig struct to make accessing elements more straight forward. Removed type 1 (for PCI-to-PCI bridges) PCI configuration space struct since it is not used.
dev/rtcreg.h:
Added macros for bit fields in RTC status registers A & B.
dev/sinic.cc:
Function name change: WriteConfig --> writeConfig.
writeConfig() now takes a pointer to data instead of a copy of data.
The accessing of elements of PCIConfig structure is updated.
dev/sinic.hh:
Function name change: WriteConfig --> writeConfig.
writeConfig() now takes a pointer to data instead of a copy of data.
dev/tsunami_io.cc:
Added implementation of new RTC and PIT classes.
dev/tsunami_io.hh:
Added classes for RTC and PIT modules.
dev/tsunamireg.h:
Added macros for DMA ports used by Tsunami-Tru64.
dev/uart8250.cc:
Got rid of a magic number.
Transmit (Tx) interrupts should clear upon a read of the Interrupt ID register.
dev/uart8250.hh:
Added comments and macros dealing with the UART Interrupt ID register.
kern/linux/linux_system.cc:
Replaced htoa() with htog().
python/m5/objects/Pci.py:
PciFake is a python class for Pci Devices that do nothing.
python/m5/objects/Tsunami.py:
TsunamiFake was renamed as IsaFake.
sim/system.cc:
Replaced htoa()s with htog()s.
dev/isa_fake.cc:
New BitKeeper file ``dev/isa_fake.cc''
TsunamiFake was renamed as IsaFake.
dev/isa_fake.hh:
New BitKeeper file ``dev/isa_fake.hh''
TsunmaiFake was renamed as IsaFake.
dev/pitreg.h:
New BitKeeper file ``dev/pitreg.h''
Useful macros for working with PIT (Periodic Interval Timer) registers.
--HG--
extra : convert_revision : 33f3a8a1034af4f6c71b32dd743e371c8613e780
python/m5/config.py:
NextEthernetAddr shouldnt' be a Singleton since we want __init__ to be
called more than once.
Make the EthernetAddr class a "proxy" so that unproxy will
be called and NextEthernetAddr will generally work correctly.
--HG--
extra : convert_revision : c89bf268e805e202ae71030fcea4833867c7e477
Make the AlphaConsole calculate the number of CPUs instead
of passing that in as a parameter.
cpu/base.cc:
pass the desired cpu_id into registerExecContext, offsetting it
by the thread number. a cpu_id of -1 means that it should be
generated for you.
cpu/base.hh:
Take the cpu_id as a parameter
cpu/o3/alpha_cpu_builder.cc:
cpu/simple/cpu.cc:
Accept the cpu_id as a parameter
while we're here, let's remove the multiplier since it is
not used.
dev/alpha_console.cc:
don't take the number of CPUs as a parameter. Calculate it from
the system based on the number of CPUs that have been registered.
move init() code to startup() to ensure that all CPUs are registerd.
dev/alpha_console.hh:
python/m5/objects/AlphaConsole.py:
don't take the number of CPUs as a parameter.
move init() code to startup() to ensure that all CPUs are registerd.
python/m5/objects/BaseCPU.py:
take the cpu_id as a parameter. Default it to -1 which means
that it will be generated.
sim/system.cc:
allow the registerExecContext functioin to take a desired
cpu_id as a parameter. Check to ensure that the id isn't
already used. Accept -1 as a request to have an id assigned.
sim/system.hh:
keep track of the number of registered exec contexts.
provide a function for accessing the number of exec contexts
that checks to ensure that they are all registered correctly.
--HG--
extra : convert_revision : 8e12f96ff8a49fa16cdbbdb4c05c651376c35788
the nsgige state machine can run. The frequency is of the actual
state transitions, and not the rate of what underlying
instructions might run at.
dev/ns_gige.cc:
Implement a state machine clock that acutally limits how fast
the state machine can run. After each state transition, a
variable is kept to hold the next state transition until the
next clock. The frequency is of the actual state transitions,
and not the rate of what underlying instructions might run at.
dev/ns_gige.hh:
Add back the rxKickEvent and txKickEvent events.
python/m5/objects/Ethernet.py:
Default the state machine clock to '0ns' so the default
behaviour doesn't change when we actually implement the
state machine clock.
--HG--
extra : convert_revision : 2db1943dee4e91ea75aaee6a91e88f27f01a09dd
Fixed printing so the tokenizer in m5 doesn't get confused
Expanded NullSimObject so it could be used as an element in a VectorParam
--HG--
extra : convert_revision : 661b1916967d663ab7aee891f15f7ca190deeba6
object and get rid of the ParamContext that each used to have.
python/m5/objects/Root.py:
Add max_time and progress_interval to the Root object
sim/root.cc:
Add max_time and progress_interval to the Root object. These
parameters used to be in their own contexts in sim_events.cc
sim/sim_events.cc:
Get rid of the ParamContext for max cycles and the progress
event. Move the functionality to the Root object
sim/sim_events.hh:
Move ProgressEvent declaration to the header so that it can
be used in other files.
--HG--
extra : convert_revision : ff664b806855e8eb9201b8a25392aa53204464f0
Make System an object that can be instantiated. For operating
systems that don't need any OS specific hacks.
python/m5/objects/AlphaConsole.py:
python/m5/objects/BaseCPU.py:
python/m5/objects/Tsunami.py:
BaseSystem -> System
--HG--
rename : python/m5/objects/BaseSystem.py => python/m5/objects/System.py
extra : convert_revision : e5d12db02abef1b0eda720b50dd2c09cb1ac5232
python/m5/config.py:
Bug fix: code was silently converting between
incompatible SimObject types as an unintended
side-effect of the object cloning support.
--HG--
extra : convert_revision : 236f4fe5370f2eddf8af8fab68e2b83dccc34305
python/m5/config.py:
Make NetworkBandwidth and MemoryBandwidth work
python/m5/objects/Ethernet.py:
Make 1Gbps default for ethernet
--HG--
extra : convert_revision : 59e62f7e62624356ae8d7304598617f60667f040
Fix description for Bus clock_ratio (no longer a ratio).
Add Clock param type (generic Frequency or Latency).
cpu/base_cpu.cc:
cpu/base_cpu.hh:
cpu/beta_cpu/alpha_full_cpu_builder.cc:
cpu/simple_cpu/simple_cpu.cc:
dev/ide_ctrl.cc:
dev/ns_gige.cc:
dev/ns_gige.hh:
dev/pciconfigall.cc:
dev/sinic.cc:
dev/tsunami_cchip.cc:
dev/tsunami_io.cc:
dev/tsunami_pchip.cc:
dev/uart.cc:
python/m5/objects/BaseCPU.py:
python/m5/objects/BaseCache.py:
python/m5/objects/BaseSystem.py:
python/m5/objects/Bus.py:
python/m5/objects/Ethernet.py:
python/m5/objects/Root.py:
sim/universe.cc:
Standardize clock parameter names to 'clock'.
Fix description for Bus clock_ratio (no longer a ratio).
python/m5/config.py:
Minor tweaks on Frequency/Latency:
- added new Clock param type to avoid ambiguities
- factored out init code into getLatency()
- made RootFrequency *not* a subclass of Frequency so it
can't be directly assigned to a Frequency paremeter
--HG--
extra : convert_revision : fc4bb8562df171b454bbf696314cda57e1ec8506
configs/splash2/run.py:
Update file for new config changes.
python/m5/config.py:
- isParamContext() not defined any more
- fix bug with re-assigning vectors over scalars
and vice versa
--HG--
rename : configs/splash2/run.mpy => configs/splash2/run.py
extra : convert_revision : 2eb28a92f8de327f6dfddd01467c61e759275f6b
Special mpy importer is gone; everything is just plain
Python now (funky, but straight-up).
May not completely work yet... generates identical ini
files for many configs/kernel settings, but I have yet
to run it against regressions. This commit is for my
own convenience and won't be pushed until more testing
is done.
python/m5/__init__.py:
Get rid of mpy_importer and param_types.
python/m5/config.py:
Major cleanup. We now have separate classes and
instances for SimObjects. Proxy handling and param
conversion significantly reorganized. No explicit
instantiation step anymore; we can dump an ini file
straight from the original tree.
Still needs more/better/truer comments.
test/genini.py:
Replace LoadMpyFile() with built-in execfile().
Export __main__.m5_build_env.
python/m5/objects/AlphaConsole.py:
python/m5/objects/AlphaFullCPU.py:
python/m5/objects/AlphaTLB.py:
python/m5/objects/BadDevice.py:
python/m5/objects/BaseCPU.py:
python/m5/objects/BaseCache.py:
python/m5/objects/BaseSystem.py:
python/m5/objects/Bus.py:
python/m5/objects/CoherenceProtocol.py:
python/m5/objects/Device.py:
python/m5/objects/DiskImage.py:
python/m5/objects/Ethernet.py:
python/m5/objects/Ide.py:
python/m5/objects/IntrControl.py:
python/m5/objects/MemTest.py:
python/m5/objects/Pci.py:
python/m5/objects/PhysicalMemory.py:
python/m5/objects/Platform.py:
python/m5/objects/Process.py:
python/m5/objects/Repl.py:
python/m5/objects/Root.py:
python/m5/objects/SimConsole.py:
python/m5/objects/SimpleDisk.py:
python/m5/objects/Tsunami.py:
python/m5/objects/Uart.py:
Fixes for eliminating mpy_importer, and modified
handling of frequency/latency params.
Also renamed parent to Parent.
--HG--
rename : python/m5/objects/AlphaConsole.mpy => python/m5/objects/AlphaConsole.py
rename : python/m5/objects/AlphaFullCPU.mpy => python/m5/objects/AlphaFullCPU.py
rename : python/m5/objects/AlphaTLB.mpy => python/m5/objects/AlphaTLB.py
rename : python/m5/objects/BadDevice.mpy => python/m5/objects/BadDevice.py
rename : python/m5/objects/BaseCPU.mpy => python/m5/objects/BaseCPU.py
rename : python/m5/objects/BaseCache.mpy => python/m5/objects/BaseCache.py
rename : python/m5/objects/BaseSystem.mpy => python/m5/objects/BaseSystem.py
rename : python/m5/objects/Bus.mpy => python/m5/objects/Bus.py
rename : python/m5/objects/CoherenceProtocol.mpy => python/m5/objects/CoherenceProtocol.py
rename : python/m5/objects/Device.mpy => python/m5/objects/Device.py
rename : python/m5/objects/DiskImage.mpy => python/m5/objects/DiskImage.py
rename : python/m5/objects/Ethernet.mpy => python/m5/objects/Ethernet.py
rename : python/m5/objects/Ide.mpy => python/m5/objects/Ide.py
rename : python/m5/objects/IntrControl.mpy => python/m5/objects/IntrControl.py
rename : python/m5/objects/MemTest.mpy => python/m5/objects/MemTest.py
rename : python/m5/objects/Pci.mpy => python/m5/objects/Pci.py
rename : python/m5/objects/PhysicalMemory.mpy => python/m5/objects/PhysicalMemory.py
rename : python/m5/objects/Platform.mpy => python/m5/objects/Platform.py
rename : python/m5/objects/Process.mpy => python/m5/objects/Process.py
rename : python/m5/objects/Repl.mpy => python/m5/objects/Repl.py
rename : python/m5/objects/Root.mpy => python/m5/objects/Root.py
rename : python/m5/objects/SimConsole.mpy => python/m5/objects/SimConsole.py
rename : python/m5/objects/SimpleDisk.mpy => python/m5/objects/SimpleDisk.py
rename : python/m5/objects/Tsunami.mpy => python/m5/objects/Tsunami.py
rename : python/m5/objects/Uart.mpy => python/m5/objects/Uart.py
extra : convert_revision : 9dc55103a6f5b40eada4ed181a71a96fae6b0b76
SConscript:
arch/isa_parser.py:
cpu/base_dyn_inst.cc:
Remove OOO CPU stuff.
arch/alpha/faults.hh:
Add fake memory fault. This will be removed eventually.
arch/alpha/isa_desc:
Change EA comp and Mem accessor to be const StaticInstPtrs.
cpu/base_dyn_inst.hh:
Update read/write calls to use load queue and store queue indices.
cpu/beta_cpu/alpha_dyn_inst.hh:
Change to const StaticInst in the register accessors.
cpu/beta_cpu/alpha_dyn_inst_impl.hh:
Update syscall code with thread numbers.
cpu/beta_cpu/alpha_full_cpu.hh:
Alter some of the full system code so it will compile without errors.
cpu/beta_cpu/alpha_full_cpu_builder.cc:
Created a DerivAlphaFullCPU class so I can instantiate different CPUs that have different template parameters.
cpu/beta_cpu/alpha_full_cpu_impl.hh:
Update some of the full system code so it compiles.
cpu/beta_cpu/alpha_params.hh:
cpu/beta_cpu/fetch_impl.hh:
Remove asid.
cpu/beta_cpu/comm.hh:
Remove global history field.
cpu/beta_cpu/commit.hh:
Comment out rename map.
cpu/beta_cpu/commit_impl.hh:
Update some of the full system code so it compiles. Also change it so that it handles memory instructions properly.
cpu/beta_cpu/cpu_policy.hh:
Removed IQ from the IEW template parameter to make it more uniform.
cpu/beta_cpu/decode.hh:
Add debug function.
cpu/beta_cpu/decode_impl.hh:
Slight updates for decode in the case where it causes a squash.
cpu/beta_cpu/fetch.hh:
cpu/beta_cpu/rob.hh:
Comment out unneccessary code.
cpu/beta_cpu/full_cpu.cc:
Changed some of the full system code so it compiles. Updated exec contexts and so forth to hopefully make multithreading easier.
cpu/beta_cpu/full_cpu.hh:
Updated some of the full system code to make it compile.
cpu/beta_cpu/iew.cc:
Removed IQ from template parameter to IEW.
cpu/beta_cpu/iew.hh:
Removed IQ from template parameter to IEW. Updated IEW to recognize the Load/Store queue.
cpu/beta_cpu/iew_impl.hh:
New handling of memory instructions through the Load/Store queue.
cpu/beta_cpu/inst_queue.hh:
Updated comment.
cpu/beta_cpu/inst_queue_impl.hh:
Slightly different handling of memory instructions due to Load/Store queue.
cpu/beta_cpu/regfile.hh:
Updated full system code so it compiles.
cpu/beta_cpu/rob_impl.hh:
Moved some code around; no major functional changes.
cpu/ooo_cpu/ooo_cpu.hh:
Slight updates to OOO CPU; still does not work.
cpu/static_inst.hh:
Remove OOO CPU stuff. Change ea comp and mem acc to return const StaticInst.
kern/kernel_stats.hh:
Extra forward declares added due to compile error.
--HG--
extra : convert_revision : 594a7cdbe57f6c2bda7d08856fcd864604a6238e
can pass simulator specific options to the device driver.
dev/ns_gige.cc:
Add the m5 register and parameter to the ns83820 device model
so that we can pass simulator specific options to the device
driver.
dev/ns_gige.hh:
dev/ns_gige_reg.h:
Add the m5 register to the ns83820 device model
--HG--
extra : convert_revision : 84674887560fa3b607e725b8e5bc8272761fcf09
(plus some small fixes).
python/m5/config.py:
Hacks to allow multiplication on Frequency/Latency-valued proxies.
Provide __rmul__ as well as __mul__ on Proxy objects.
test/genini.py:
Default value for -EFOO should be True not 1 (since 1 is no longer
convertable to Bool).
--HG--
extra : convert_revision : f8a221fcd9e095fdd7b7db4be0ed0cdcd20074be
CPU cycle ticks. This allows the user to have CPUs of different
frequencies, and also allows frequencies and latencies that are
not evenly divisible by the CPU frequency. For now, the CPU
frequency is still set to the global frequency, but soon, we'll
hopefully make the global frequency fixed at something like 1THz
and set all other frequencies independently.
arch/alpha/ev5.cc:
The cycles counter is based on the current cpu cycle.
cpu/base_cpu.cc:
frequency isn't the cpu parameter anymore, cycleTime is.
cpu/base_cpu.hh:
frequency isn't the cpu parameter anymore, cycleTime is.
create several public functions for getting the cpu frequency
and the numbers of ticks for a given number of cycles, etc.
cpu/memtest/memtest.cc:
cpu/simple_cpu/simple_cpu.cc:
cpu/simple_cpu/simple_cpu.hh:
cpu/trace/trace_cpu.cc:
Now that ticks aren't cpu cycles, fixup code to advance
by the proper number of ticks.
cpu/memtest/memtest.hh:
cpu/trace/trace_cpu.hh:
Provide a function to get the number of ticks for a given
number of cycles.
dev/alpha_console.cc:
Update for changes in the way that frequencies and latencies are
accessed. Move some stuff to init()
dev/alpha_console.hh:
Need a pointer to the system and the cpu to get the frequency
so we can pass the info to the console code.
dev/etherbus.cc:
dev/etherbus.hh:
dev/etherlink.cc:
dev/etherlink.hh:
dev/ethertap.cc:
dev/ide_disk.hh:
dev/ns_gige.cc:
dev/ns_gige.hh:
update for changes in the way bandwidths are passed from
python to C++ to accomidate the new way that ticks works.
dev/ide_disk.cc:
update for changes in the way bandwidths are passed from
python to C++ to accomidate the new way that ticks works.
Add some extra debugging printfs
dev/platform.cc:
dev/sinic.cc:
dev/sinic.hh:
outline the constructor and destructor
dev/platform.hh:
outline the constructor and destructor.
don't keep track of the interrupt frequency. Only provide the
accessor function.
dev/tsunami.cc:
dev/tsunami.hh:
outline the constructor and destructor
Don't set the interrupt frequency here. Get it from the actual device
that does the interrupting.
dev/tsunami_io.cc:
dev/tsunami_io.hh:
Make the interrupt interval a configuration parameter. (And convert
the interval to the new latency/frequency stuff in the python)
kern/linux/linux_system.cc:
update for changes in the way bandwidths are passed from
python to C++ to accomidate the new way that ticks works.
For now, we must get the boot cpu's frequency as a parameter
since allowing the system to have a pointer to the boot cpu would
cause a cycle.
kern/tru64/tru64_system.cc:
For now, we must get the boot cpu's frequency as a parameter
since allowing the system to have a pointer to the boot cpu would
cause a cycle.
python/m5/config.py:
Fix support for cycle_time relative latencies and frequencies.
Add support for getting a NetworkBandwidth or a MemoryBandwidth.
python/m5/objects/BaseCPU.mpy:
All CPUs now have a cycle_time. The default is the global frequency,
but it is now possible to set the global frequency to some large value
(like 1THz) and set each CPU frequency independently.
python/m5/objects/BaseCache.mpy:
python/m5/objects/Ide.mpy:
Make this a Latency parameter
python/m5/objects/BaseSystem.mpy:
We need to pass the boot CPU's frequency to the system
python/m5/objects/Ethernet.mpy:
Update parameter types to use latency and bandwidth types
python/m5/objects/Platform.mpy:
this frequency isn't needed. We get it from the clock interrupt.
python/m5/objects/Tsunami.mpy:
The clock generator should hold the frequency
sim/eventq.hh:
Need to remove this assertion because the writeback event
queue is different from the CPU's event queue which can cause
this assertion to fail.
sim/process.cc:
Fix comment.
sim/system.hh:
Struct member to hold the boot CPU's frequency.
sim/universe.cc:
remove unneeded variable.
--HG--
extra : convert_revision : 51efe4041095234bf458d9b3b0d417f4cae16fdc
