xv6-cs450/bootother.S

#include "asm.h"

# Each non-boot CPU ("AP") is started up in response to a STARTUP
# IPI from the boot CPU.  Section B.4.2 of the Multi-Processor
# Specification says that the AP will start in real mode with CS:IP
# set to XY00:0000, where XY is an 8-bit value sent with the
# STARTUP. Thus this code must start at a 4096-byte boundary.
#
# Because this code sets DS to zero, it must sit
# at an address in the low 2^16 bytes.
#
# Bootothers (in main.c) sends the STARTUPs, one at a time.
# It puts this code (start) at 0x7000.
# It puts the correct %esp in start-4,
# and the place to jump to in start-8.
#
# This code is identical to bootasm.S except:
#   - it does not need to enable A20
#   - it uses the address at start-4 for the %esp
#   - it jumps to the address at start-8 instead of calling bootmain

#define SEG_KCODE 1  // kernel code
#define SEG_KDATA 2  // kernel data+stack

#define CR0_PE    1  // protected mode enable bit

.code16                       # Assemble for 16-bit mode
.globl start
start:
  cli                         # Disable interrupts

  # Set up the important data segment registers (DS, ES, SS).
  xorw    %ax,%ax             # Segment number zero
  movw    %ax,%ds             # -> Data Segment
  movw    %ax,%es             # -> Extra Segment
  movw    %ax,%ss             # -> Stack Segment

//PAGEBREAK!
  # Switch from real to protected mode, using a bootstrap GDT
  # and segment translation that makes virtual addresses 
  # identical to physical addresses, so that the 
  # effective memory map does not change during the switch.
  lgdt    gdtdesc
  movl    %cr0, %eax
  orl     $CR0_PE, %eax
  movl    %eax, %cr0

  # Jump to next instruction, but in 32-bit code segment.
  # Switches processor into 32-bit mode.
  ljmp    $(SEG_KCODE<<3), $start32

.code32                       # Assemble for 32-bit mode
start32:
  # Set up the protected-mode data segment registers
  movw    $(SEG_KDATA<<3), %ax    # Our data segment selector
  movw    %ax, %ds                # -> DS: Data Segment
  movw    %ax, %es                # -> ES: Extra Segment
  movw    %ax, %ss                # -> SS: Stack Segment
  movw    $0, %ax                 # Zero segments not ready for use
  movw    %ax, %fs                # -> FS
  movw    %ax, %gs                # -> GS

  # Set up the stack pointer and call into C.
  movl    start-4, %esp
  call	*(start-8)

  # If the call returns (it shouldn't), trigger a Bochs
  # breakpoint if running under Bochs, then loop.
  movw    $0x8a00, %ax            # 0x8a00 -> port 0x8a00
  movw    %ax, %dx
  outw    %ax, %dx
  movw    $0x8e00, %ax            # 0x8e00 -> port 0x8a00
  outw    %ax, %dx
spin:
  jmp     spin

# Bootstrap GDT
.p2align 2                                # force 4 byte alignment
gdt:
  SEG_NULLASM                             # null seg
  SEG_ASM(STA_X|STA_R, 0x0, 0xffffffff)   # code seg
  SEG_ASM(STA_W, 0x0, 0xffffffff)         # data seg

gdtdesc:
  .word   (gdtdesc - gdt - 1)                            # sizeof(gdt) - 1
  .long   gdt                             # address gdt