- if supported, override BSY/DRQ flags and start the port anyway if it
times out with DET=3h status during device detection;
- no longer rely on the device signature to be set; unless a valid
signature is obtained, try both ATA and ATAPI device identification.
- do not start a port before the BSY and DRQ flags have been cleared;
as such, poll on device status rather than signature availability.
- change "ahci_sig_timeout" to "ahci_device_timeout" variable setting
accordingly; this variable determines the polling duration before a
newly attached device is given up on, and uses 30 seconds as default;
- use port connect changes (PCS/X/DET->1h) to kick off polling for an
attached device; detachment is still detected by means of PhyRdy
status changes (PRCS/N/DET<->3h).
- the "ahci_sig_timeout" variable now denotes the entire checking
period, and the delay between checks has been hardcoded; what was
previously "ahci_sig_checks" is now computed from those two;
- timeout values are no longer used for both millisecond and clock
tick values, and better typed;
- the computation of timeouts is no longer off by half a second.
There is no need to set/clear PxCMD.FRE on every port start/stop.
Also remove some already useless and now also incomplete port
reinitialization at startup.
. all invocations were S or D, so can safely be dropped
to prepare for the segmentless world
. still assign D to the SCP_SEG field in the message
to make previous kernels usable
- remove PCI tables where system.conf suffices
- remove drivers' ability to mess up NIC order
- fix dp8390 PCI enumeration
- convert ti1225 to instance model
- add system.conf entry for ti1225
This removes a race condition when the block driver performs a
complete restart after a crash (the new default). If any user of
the driver finds out its new endpoint and sends a request to the
new driver instance before this instance has had the chance to
initialize, then its initialization would clear all IPC state and
thereby erroneously cancel the incoming request. Clearing IPC
state is only desired upon a stateful restart (where the driver's
endpoint is retained). This information is now passed to and used
by libblockdriver accordingly.
Each block driver now gets to specify whether it is a disk block
driver, which implies it wants the library to handle getting and
setting partitions for it.
This patch separates the character and block driver communication
protocols. The old character protocol remains the same, but a new
block protocol is introduced. The libdriver library is replaced by
two new libraries: libchardriver and libblockdriver. Their exposed
API, and drivers that use them, have been updated accordingly.
Together, libbdev and libblockdriver now completely abstract away
the message format used by the block protocol. As the memory driver
is both a character and a block device driver, it now implements its
own message loop.
The most important semantic change made to the block protocol is that
it is no longer possible to return both partial results and an error
for a single transfer. This simplifies the interaction between the
caller and the driver, as the I/O vector no longer needs to be copied
back. Also, drivers are now no longer supposed to decide based on the
layout of the I/O vector when a transfer should be cut short. Put
simply, transfers are now supposed to either succeed completely, or
result in an error.
After this patch, the state of the various pieces is as follows:
- block protocol: stable
- libbdev API: stable for synchronous communication
- libblockdriver API: needs slight revision (the drvlib/partition API
in particular; the threading API will also change shortly)
- character protocol: needs cleanup
- libchardriver API: needs cleanup accordingly
- driver restarts: largely unsupported until endpoint changes are
reintroduced
As a side effect, this patch eliminates several bugs, hacks, and gcc
-Wall and -W warnings all over the place. It probably introduces a
few new ones, too.
Update warning: this patch changes the protocol between MFS and disk
drivers, so in order to use old/new images, the MFS from the ramdisk
must be used to mount all file systems.
While no problems have been observed in practice yet, modern compilers
may reorder memory access operations, and that could lead to problems
with memory-mapped I/O typically done by drivers. This patch prevents
any potentially problematic reordering by the compiler in the AHCI
driver.
This patch adds support for executing multiple concurrent requests on
different devices on the same AHCI controller. The libdriver library
has been extended to include a generic multithreading interface, and
the AHCI driver has been extended to make use of this interface.
The original version of this code has been written by Arne Welzel.
Before safecopies, the IO_ENDPT and DL_ENDPT message fields were needed
to know which actual process to copy data from/to, as that process may
not always be the caller. Now that we have full safecopy support, these
fields have become useless for that purpose: the owner of the grant is
*always* the caller. Allowing the caller to supply another endpoint is
in fact dangerous, because the callee may then end up using a grant
from a third party. One could call this a variant of the confused
deputy problem.
From now on, safecopy calls should always use the caller's endpoint as
grant owner. This fully obsoletes the DL_ENDPT field in the
inet/ethernet protocol. IO_ENDPT has other uses besides identifying the
grant owner though. This patch renames IO_ENDPT to USER_ENDPT, not only
because that is a more fitting name (it should never be used for I/O
after all), but also in order to intentionally break any old system
source code outside the base system. If this patch breaks your code,
fixing it is fairly simple:
- DL_ENDPT should be replaced with m_source;
- IO_ENDPT should be replaced with m_source when used for safecopies;
- IO_ENDPT should be replaced with USER_ENDPT for any other use, e.g.
when setting REP_ENDPT, matching requests in CANCEL calls, getting
DEV_SELECT flags, and retrieving of the real user process's endpoint
in DEV_OPEN.
The changes in this patch are binary backward compatible.
- check the DF status flag after each command
- increase I/O timeout from 15 to 30 seconds
- share some code between ATA and ATAPI after all
- produce more accurate errors on DIOCEJECT
- rename AHCI_ID_SIZE to the more appropriate ATA_ID_SIZE
- rearrange ahci.h in a now more sensible way
