7e11828c6e
Created a new directory called bsp (board support package) to hold board or system on chip specific code. The idea is the following. Change-Id: Ica5886806940facae2fa5492fcc938b3c2b989be
82 lines
2 KiB
C
82 lines
2 KiB
C
#include <assert.h>
|
|
#include <sys/types.h>
|
|
#include <machine/cpu.h>
|
|
#include <minix/type.h>
|
|
#include <minix/board.h>
|
|
#include <io.h>
|
|
|
|
#include "kernel/kernel.h"
|
|
#include "kernel/proc.h"
|
|
#include "kernel/vm.h"
|
|
#include "kernel/proto.h"
|
|
#include "arch_proto.h"
|
|
#include "bsp_reset.h"
|
|
|
|
#include "omap_rtc.h"
|
|
|
|
#define AM335X_CM_BASE 0x44E00000
|
|
#define AM335X_CM_SIZE 0x1000
|
|
|
|
#define AM335X_PRM_DEVICE_OFFSET 0xf00
|
|
#define AM335X_PRM_RSTCTRL_REG 0x00
|
|
#define AM335X_RST_GLOBAL_WARM_SW_BIT 0
|
|
|
|
#define DM37XX_CM_BASE 0x48307000
|
|
#define DM37XX_CM_SIZE 0x1000
|
|
#define DM37XX_PRM_RSTCTRL_REG 0x250
|
|
#define DM37XX_RST_DPLL3_BIT 2
|
|
|
|
struct omap_reset
|
|
{
|
|
vir_bytes base;
|
|
vir_bytes size;
|
|
};
|
|
|
|
static struct omap_reset omap_reset;
|
|
|
|
static kern_phys_map reset_phys_map;
|
|
|
|
void
|
|
bsp_reset_init(void)
|
|
{
|
|
if(BOARD_IS_BBXM(machine.board_id)) {
|
|
omap_reset.base = DM37XX_CM_BASE;
|
|
omap_reset.size = DM37XX_CM_SIZE;
|
|
} else if(BOARD_IS_BB(machine.board_id)) {
|
|
omap_reset.base = AM335X_CM_BASE;
|
|
omap_reset.size = AM335X_CM_SIZE;
|
|
}
|
|
|
|
kern_phys_map_ptr(omap_reset.base, omap_reset.size, &reset_phys_map,
|
|
(vir_bytes) &omap_reset.base);
|
|
}
|
|
|
|
void
|
|
bsp_reset(void)
|
|
{
|
|
if(BOARD_IS_BBXM(machine.board_id)) {
|
|
mmio_set((omap_reset.base + DM37XX_PRM_RSTCTRL_REG), (1 << DM37XX_RST_DPLL3_BIT));
|
|
} else if(BOARD_IS_BB(machine.board_id)) {
|
|
mmio_set((omap_reset.base + AM335X_PRM_DEVICE_OFFSET + AM335X_PRM_RSTCTRL_REG), (1 << AM335X_RST_GLOBAL_WARM_SW_BIT));
|
|
}
|
|
}
|
|
|
|
void bsp_poweroff(void)
|
|
{
|
|
|
|
/*
|
|
* The am335x can signal an external power management chip to cut the power
|
|
* by toggling the PMIC_POWER_EN pin. It might fail if there isn't an
|
|
* external PMIC or if the PMIC hasn't been configured to respond to toggles.
|
|
* The only way to pull the pin low is via ALARM2 (see TRM 20.3.3.8).
|
|
* At this point PM should have already signaled readclock to set the alarm.
|
|
*/
|
|
if (BOARD_IS_BB(machine.board_id)) {
|
|
/* rtc was frozen to prevent premature power-off, unfreeze it now */
|
|
omap3_rtc_run();
|
|
|
|
/* wait for the alarm to go off and PMIC to disable power to SoC */
|
|
while (1);
|
|
}
|
|
}
|
|
|