100 lines
3.8 KiB
ArmAsm
100 lines
3.8 KiB
ArmAsm
#
|
|
# from JOS
|
|
#
|
|
|
|
#include "asm.h"
|
|
|
|
.set PROT_MODE_CSEG,0x8 # code segment selector
|
|
.set PROT_MODE_DSEG,0x10 # data segment selector
|
|
.set CR0_PE_ON,0x1 # protected mode enable flag
|
|
|
|
###################################################################################
|
|
# ENTRY POINT
|
|
# This code should be stored in the first sector of the hard disk.
|
|
# After the BIOS initializes the hardware on startup or system reset,
|
|
# it loads this code at physical address 0x7c00 - 0x7d00 (512 bytes).
|
|
# Then the BIOS jumps to the beginning of it, address 0x7c00,
|
|
# while running in 16-bit real-mode (8086 compatibility mode).
|
|
# The Code Segment register (CS) is initially zero on entry.
|
|
#
|
|
# This code switches into 32-bit protected mode so that all of
|
|
# memory can accessed, then calls into C.
|
|
###################################################################################
|
|
|
|
.globl start # Entry point
|
|
start: .code16 # This runs in real mode
|
|
cli # Disable interrupts
|
|
cld # String operations increment
|
|
|
|
# Set up the important data segment registers (DS, ES, SS).
|
|
xorw %ax,%ax # Segment number zero
|
|
movw %ax,%ds # -> Data Segment
|
|
movw %ax,%es # -> Extra Segment
|
|
movw %ax,%ss # -> Stack Segment
|
|
|
|
# Set up the stack pointer, growing downward from 0x7c00.
|
|
movw $start,%sp # Stack Pointer
|
|
|
|
#### Enable A20:
|
|
#### For fascinating historical reasons (related to the fact that
|
|
#### the earliest 8086-based PCs could only address 1MB of physical memory
|
|
#### and subsequent 80286-based PCs wanted to retain maximum compatibility),
|
|
#### physical address line 20 is tied to low when the machine boots.
|
|
#### Obviously this a bit of a drag for us, especially when trying to
|
|
#### address memory above 1MB. This code undoes this.
|
|
|
|
seta20.1: inb $0x64,%al # Get status
|
|
testb $0x2,%al # Busy?
|
|
jnz seta20.1 # Yes
|
|
movb $0xd1,%al # Command: Write
|
|
outb %al,$0x64 # output port
|
|
seta20.2: inb $0x64,%al # Get status
|
|
testb $0x2,%al # Busy?
|
|
jnz seta20.2 # Yes
|
|
movb $0xdf,%al # Enable
|
|
outb %al,$0x60 # A20
|
|
|
|
#### Switch from real to protected mode
|
|
#### The descriptors in our GDT allow all physical memory to be accessed.
|
|
#### Furthermore, the descriptors have base addresses of 0, so that the
|
|
#### segment translation is a NOP, ie. virtual addresses are identical to
|
|
#### their physical addresses. With this setup, immediately after
|
|
#### enabling protected mode it will still appear to this code
|
|
#### that it is running directly on physical memory with no translation.
|
|
#### This initial NOP-translation setup is required by the processor
|
|
#### to ensure that the transition to protected mode occurs smoothly.
|
|
|
|
real_to_prot: cli # Mandatory since we dont set up an IDT
|
|
lgdt gdtdesc # load GDT -- mandatory in protected mode
|
|
movl %cr0, %eax # turn on protected mode
|
|
orl $CR0_PE_ON, %eax #
|
|
movl %eax, %cr0 #
|
|
### CPU magic: jump to relocation, flush prefetch queue, and reload %cs
|
|
### Has the effect of just jmp to the next instruction, but simultaneous
|
|
### loads CS with $PROT_MODE_CSEG.
|
|
ljmp $PROT_MODE_CSEG, $protcseg
|
|
|
|
#### we are in 32-bit protected mode (hence the .code32)
|
|
.code32
|
|
protcseg:
|
|
# Set up the protected-mode data segment registers
|
|
movw $PROT_MODE_DSEG, %ax # Our data segment selector
|
|
movw %ax, %ds # -> DS: Data Segment
|
|
movw %ax, %es # -> ES: Extra Segment
|
|
movw %ax, %fs # -> FS
|
|
movw %ax, %gs # -> GS
|
|
movw %ax, %ss # -> SS: Stack Segment
|
|
|
|
call cmain # finish the boot load from C.
|
|
# cmain() should not return
|
|
spin: jmp spin # ..but in case it does, spin
|
|
|
|
.p2align 2 # force 4 byte alignment
|
|
gdt:
|
|
SEG_NULL # null seg
|
|
SEG(STA_X|STA_R, 0x0, 0xffffffff) # code seg
|
|
SEG(STA_W, 0x0, 0xffffffff) # data seg
|
|
|
|
gdtdesc:
|
|
.word 0x17 # sizeof(gdt) - 1
|
|
.long gdt # address gdt
|