minix/drivers/dpeth/dp.c

650 lines
18 KiB
C

/*
** File: eth.c Version 1.00, Jan. 14, 1997
**
** Author: Giovanni Falzoni <gfalzoni@inwind.it>
**
** This file contains the ethernet device driver main task.
** It has to be integrated with the board specific drivers.
** It is a rewriting of Minix 2.0.0 ethernet driver (dp8390.c)
** to remove bord specific code. It should operate (I hope)
** with any board driver.
**
** The valid messages and their parameters are:
**
** m_type DL_PORT DL_PROC DL_COUNT DL_MODE DL_ADDR
** +------------+---------+---------+--------+-------+---------+
** | HARD_INT | | | | | |
** +------------+---------+---------+--------+-------+---------+
** | SYN_ALARM | | | | | |
** +------------+---------+---------+--------+-------+---------+
** | HARD_STOP | | | | | |
** +------------+---------+---------+--------+-------+---------+
** | FKEY_PRESSED | | | | | (99)
** +------------+---------+---------+--------+-------+---------+
** | DL_WRITE | port nr | proc nr | count | mode | address | (3)
** +------------+---------+---------+--------+-------+---------+
** | DL_WRITEV | port nr | proc nr | count | mode | address | (4)
** +------------+---------+---------+--------+-------+---------+
** | DL_READ | port nr | proc nr | count | | address | (5)
** +------------+---------+---------+--------+-------+---------+
** | DL_READV | port nr | proc nr | count | | address | (6)
** +------------+---------+---------+--------+-------+---------+
** | DL_INIT | port nr | proc nr | | mode | address | (7)
** +------------+---------+---------+--------+-------+---------+
** | DL_STOP | port_nr | | | | | (8)
** +------------+---------+---------+--------+-------+---------+
** | DL_GETSTAT | port nr | proc nr | | | address | (9)
** +------------+---------+---------+--------+-------+---------+
**
** The messages sent are:
**
** m-type DL_PORT DL_PROC DL_COUNT DL_STAT DL_CLCK
** +------------+---------+---------+--------+---------+---------+
** |DL_TASK_REPL| port nr | proc nr |rd-count| err|stat| clock | (21)
** +------------+---------+---------+--------+---------+---------+
**
** m_type m3_i1 m3_i2 m3_ca1
** +------------+---------+---------+---------------+
** |DL_INIT_REPL| port nr |last port| ethernet addr | (20)
** +------------+---------+---------+---------------+
**
** $Log$
** Revision 1.3 2005/07/20 15:28:04 jnherder
** Kernel sends SIGKSTOP just before shutdown. Drivers do clean up and exit.
**
** Revision 1.2 2005/07/14 15:15:17 jnherder
** Renamed some system library functionality.
**
** Revision 1.1 2005/06/29 10:16:46 beng
** Import of dpeth 3c501/3c509b/.. ethernet driver by
** Giovanni Falzoni <fgalzoni@inwind.it>.
**
** Revision 2.0 2005/06/26 16:16:46 lsodgf0
** Initial revision for Minix 3.0.6
**
** $Id$
*/
#include "drivers.h"
#include <minix/keymap.h>
#include <net/hton.h>
#include <net/gen/ether.h>
#include <net/gen/eth_io.h>
#include "dp.h"
#if ENABLE_NETWORKING == 1
/*
** Local data
*/
static dpeth_t de_table[DE_PORT_NR];
static int dpeth_tasknr = ANY;
typedef struct dp_conf { /* Configuration description structure */
port_t dpc_port;
int dpc_irq;
phys_bytes dpc_mem;
char *dpc_envvar;
} dp_conf_t;
/* Device default configuration */
static dp_conf_t dp_conf[DE_PORT_NR] = {
/* I/O port, IRQ, Buff addr, Env. var, Buf. selector */
{ 0x300, 5, 0xC8000, "DPETH0", },
{ 0x280, 10, 0xCC000, "DPETH1", },
};
static const char CopyErrMsg[] = "unable to read/write user data";
static const char PortErrMsg[] = "illegal port";
static const char RecvErrMsg[] = "receive failed";
static const char SendErrMsg[] = "send failed";
static const char SizeErrMsg[] = "illegal packet size";
static const char TypeErrMsg[] = "illegal message type";
static const char DevName[] = "eth#?";
/*
** Name: void reply(dpeth_t *dep, int err)
** Function: Fills a DL_TASK_REPLY reply message and sends it.
*/
static void reply(dpeth_t * dep, int err)
{
message reply;
int status = FALSE;
if (dep->de_flags & DEF_ACK_SEND) status |= DL_PACK_SEND;
if (dep->de_flags & DEF_ACK_RECV) status |= DL_PACK_RECV;
reply.m_type = DL_TASK_REPLY;
reply.DL_PORT = dep - de_table;
reply.DL_PROC = dep->de_client;
reply.DL_STAT = status | ((u32_t) err << 16);
reply.DL_COUNT = dep->de_read_s;
getuptime(&reply.DL_CLCK);
DEBUG(printf("\t reply %d (%ld)\n", reply.m_type, reply.DL_STAT));
if ((status = send(dep->de_client, &reply)) != OK)
panic(dep->de_name, SendErrMsg, dep->de_client);
dep->de_read_s = 0;
dep->de_flags &= NOT(DEF_ACK_SEND | DEF_ACK_RECV);
return;
}
/*
** Name: void dp_confaddr(dpeth_t *dep)
** Function: Chechs environment for a User defined ethernet address.
*/
static void dp_confaddr(dpeth_t * dep)
{
static char ea_fmt[] = "x:x:x:x:x:x";
char ea_key[16];
int ix;
long val;
strcpy(ea_key, dp_conf[dep - de_table].dpc_envvar);
strcat(ea_key, "_EA");
for (ix = 0; ix < SA_ADDR_LEN; ix++) {
val = dep->de_address.ea_addr[ix];
if (env_parse(ea_key, ea_fmt, ix, &val, 0x00L, 0xFFL) != EP_SET)
break;
dep->de_address.ea_addr[ix] = val;
}
if (ix != 0 && ix != SA_ADDR_LEN)
/* It's all or nothing, force a panic */
env_parse(ea_key, "?", 0, &val, 0L, 0L);
return;
}
/*
** Name: void update_conf(dpeth_t *dep, dp_conf_t *dcp)
** Function: Gets the default settings from 'dp_conf' table and
** modifies them from the environment.
*/
static void update_conf(dpeth_t * dep, dp_conf_t * dcp)
{
static char dpc_fmt[] = "x:d:x";
long val;
dep->de_mode = DEM_SINK;
val = dcp->dpc_port; /* Get I/O port address */
switch (env_parse(dcp->dpc_envvar, dpc_fmt, 0, &val, 0x000L, 0x3FFL)) {
case EP_OFF: dep->de_mode = DEM_DISABLED; break;
case EP_ON:
case EP_SET: dep->de_mode = DEM_ENABLED; break;
}
dep->de_base_port = val;
val = dcp->dpc_irq | DEI_DEFAULT; /* Get Interrupt line (IRQ) */
env_parse(dcp->dpc_envvar, dpc_fmt, 1, &val, 0L, (long) NR_IRQ_VECTORS - 1);
dep->de_irq = val;
val = dcp->dpc_mem; /* Get shared memory address */
env_parse(dcp->dpc_envvar, dpc_fmt, 2, &val, 0L, LONG_MAX);
dep->de_linmem = val;
return;
}
/*
** Name: void do_dump(message *mp)
** Function: Displays statistics on screen (SFx key from console)
*/
static void do_dump(message *mp)
{
dpeth_t *dep;
int port;
printf("\n\n");
for (port = 0, dep = de_table; port < DE_PORT_NR; port += 1, dep += 1) {
if (dep->de_mode == DEM_DISABLED) continue;
printf("%s statistics:\t\t", dep->de_name);
/* Network interface status */
printf("Status: 0x%04x\n\n", dep->de_flags);
(*dep->de_dumpstatsf) (dep);
/* Transmitted/received bytes */
printf("Tx bytes:%10ld\t", dep->bytes_Tx);
printf("Rx bytes:%10ld\n", dep->bytes_Rx);
/* Transmitted/received packets */
printf("Tx OK: %8ld\t", dep->de_stat.ets_packetT);
printf("Rx OK: %8ld\n", dep->de_stat.ets_packetR);
/* Transmit/receive errors */
printf("Tx Err: %8ld\t", dep->de_stat.ets_sendErr);
printf("Rx Err: %8ld\n", dep->de_stat.ets_recvErr);
/* Transmit unnerruns/receive overrruns */
printf("Tx Und: %8ld\t", dep->de_stat.ets_fifoUnder);
printf("Rx Ovr: %8ld\n", dep->de_stat.ets_fifoOver);
/* Transmit collisions/receive CRC errors */
printf("Tx Coll: %8ld\t", dep->de_stat.ets_collision);
printf("Rx CRC: %8ld\n", dep->de_stat.ets_CRCerr);
}
return;
}
/*
** Name: void get_userdata(int user_proc, vir_bytes user_addr, int count, void *loc_addr)
** Function: Copies data from user area.
*/
static void get_userdata(int user_proc, vir_bytes user_addr, int count, void *loc_addr)
{
int rc;
vir_bytes len;
len = (count > IOVEC_NR ? IOVEC_NR : count) * sizeof(iovec_t);
if ((rc = sys_datacopy(user_proc, user_addr, SELF, (vir_bytes)loc_addr, len)) != OK)
panic(DevName, CopyErrMsg, rc);
return;
}
/*
** Name: void do_first_init(dpeth_t *dep, dp_conf_t *dcp);
** Function: Init action to setup task
*/
static void do_first_init(dpeth_t *dep, dp_conf_t *dcp)
{
if (dep->de_linmem != 0) {
dep->de_memsegm = BIOS_SEG;
/* phys2seg(&dep->de_memsegm, &dep->de_memoffs, dep->de_linmem); */
} else
dep->de_linmem = 0xFFFF0000;
/* Make sure statisics are cleared */
memset((void *) &(dep->de_stat), 0, sizeof(eth_stat_t));
/* Device specific initialization */
(*dep->de_initf) (dep);
/* Set the interrupt handler policy */
sys_irqsetpolicy(dep->de_irq, IRQ_REENABLE, &dep->de_hook);
sys_irqenable(&dep->de_hook);
return;
}
/*
** Name: void do_init(message *mp)
** Function: Checks for hardware presence.
** Provides initialization of hardware and data structures
*/
static void do_init(message * mp)
{
int port;
dpeth_t *dep;
dp_conf_t *dcp;
message reply_mess;
port = mp->DL_PORT;
if (port >= 0 && port < DE_PORT_NR) {
dep = &de_table[port];
dcp = &dp_conf[port];
strcpy(dep->de_name, DevName);
dep->de_name[4] = '0' + port;
if (dep->de_mode == DEM_DISABLED) {
update_conf(dep, dcp); /* First time thru */
if (dep->de_mode == DEM_ENABLED &&
!el1_probe(dep) && /* Probe for 3c501 */
!wdeth_probe(dep) && /* Probe for WD80x3 */
!ne_probe(dep) && /* Probe for NEx000 */
!el2_probe(dep) && /* Probe for 3c503 */
!el3_probe(dep)) { /* Probe for 3c509 */
printf("%s: warning no ethernet card found at 0x%04X\n",
dep->de_name, dep->de_base_port);
dep->de_mode = DEM_DISABLED;
}
}
/* 'de_mode' may change if probe routines fail, test again */
switch (dep->de_mode) {
case DEM_DISABLED:
/* Device is configured OFF or hardware probe failed */
port = ENXIO;
break;
case DEM_ENABLED:
/* Device is present and probed */
if (dep->de_flags == DEF_EMPTY) {
/* These actions only the first time */
do_first_init(dep, dcp);
dep->de_flags |= DEF_ENABLED;
}
dep->de_flags &= NOT(DEF_PROMISC | DEF_MULTI | DEF_BROAD);
if (mp->DL_MODE & DL_PROMISC_REQ)
dep->de_flags |= DEF_PROMISC | DEF_MULTI | DEF_BROAD;
if (mp->DL_MODE & DL_MULTI_REQ) dep->de_flags |= DEF_MULTI;
if (mp->DL_MODE & DL_BROAD_REQ) dep->de_flags |= DEF_BROAD;
(*dep->de_flagsf) (dep);
dep->de_client = mp->m_source;
break;
case DEM_SINK:
/* Device not present (sink mode) */
memset(dep->de_address.ea_addr, 0, sizeof(ether_addr_t));
dp_confaddr(dep); /* Station address from env. */
break;
default: break;
}
*(ether_addr_t *) reply_mess.m3_ca1 = dep->de_address;
} else /* Port number is out of range */
port = ENXIO;
reply_mess.m_type = DL_INIT_REPLY;
reply_mess.m3_i1 = port;
reply_mess.m3_i2 = DE_PORT_NR;
DEBUG(printf("\t reply %d\n", reply_mess.m_type));
if (send(mp->m_source, &reply_mess) != OK) /* Can't send */
panic(dep->de_name, SendErrMsg, mp->m_source);
return;
}
/*
** Name: void dp_next_iovec(iovec_dat_t *iovp)
** Function: Retrieves data from next iovec element.
*/
PUBLIC void dp_next_iovec(iovec_dat_t * iovp)
{
iovp->iod_iovec_s -= IOVEC_NR;
iovp->iod_iovec_addr += IOVEC_NR * sizeof(iovec_t);
get_userdata(iovp->iod_proc_nr, iovp->iod_iovec_addr,
iovp->iod_iovec_s, iovp->iod_iovec);
return;
}
/*
** Name: int calc_iovec_size(iovec_dat_t *iovp)
** Function: Compute the size of a request.
*/
static int calc_iovec_size(iovec_dat_t * iovp)
{
int size, ix;
size = ix = 0;
do {
size += iovp->iod_iovec[ix].iov_size;
if (++ix >= IOVEC_NR) {
dp_next_iovec(iovp);
ix = 0;
}
/* Till all vectors added */
} while (ix < iovp->iod_iovec_s);
return size;
}
/*
** Name: void do_vwrite(message *mp, int vectored)
** Function:
*/
static void do_vwrite(message * mp, int vectored)
{
int port, size;
dpeth_t *dep;
port = mp->DL_PORT;
if (port < 0 || port >= DE_PORT_NR) /* Check for illegal port number */
panic(dep->de_name, PortErrMsg, port);
dep = &de_table[port];
dep->de_client = mp->DL_PROC;
if (dep->de_mode == DEM_ENABLED) {
if (dep->de_flags & DEF_SENDING) /* Is sending in progress? */
panic(dep->de_name, "send already in progress ", NO_NUM);
dep->de_write_iovec.iod_proc_nr = mp->DL_PROC;
if (vectored) {
get_userdata(mp->DL_PROC, (vir_bytes) mp->DL_ADDR,
mp->DL_COUNT, dep->de_write_iovec.iod_iovec);
dep->de_write_iovec.iod_iovec_s = mp->DL_COUNT;
dep->de_write_iovec.iod_iovec_addr = (vir_bytes) mp->DL_ADDR;
size = calc_iovec_size(&dep->de_write_iovec);
} else {
dep->de_write_iovec.iod_iovec[0].iov_addr = (vir_bytes) mp->DL_ADDR;
dep->de_write_iovec.iod_iovec[0].iov_size = size = mp->DL_COUNT;
dep->de_write_iovec.iod_iovec_s = 1;
dep->de_write_iovec.iod_iovec_addr = 0;
}
if (size < ETH_MIN_PACK_SIZE || size > ETH_MAX_PACK_SIZE)
panic(dep->de_name, SizeErrMsg, size);
dep->de_flags |= DEF_SENDING;
(*dep->de_sendf) (dep, FALSE, size);
} else if (dep->de_mode == DEM_SINK)
dep->de_flags |= DEF_ACK_SEND;
reply(dep, OK);
return;
}
/*
** Name: void do_vread(message *mp, int vectored)
** Function:
*/
static void do_vread(message * mp, int vectored)
{
int port, size;
dpeth_t *dep;
port = mp->DL_PORT;
if (port < 0 || port >= DE_PORT_NR) /* Check for illegal port number */
panic(dep->de_name, PortErrMsg, port);
dep = &de_table[port];
dep->de_client = mp->DL_PROC;
if (dep->de_mode == DEM_ENABLED) {
if (dep->de_flags & DEF_READING) /* Reading in progress */
panic(dep->de_name, "read already in progress", NO_NUM);
dep->de_read_iovec.iod_proc_nr = mp->DL_PROC;
if (vectored) {
get_userdata(mp->DL_PROC, (vir_bytes) mp->DL_ADDR,
mp->DL_COUNT, dep->de_read_iovec.iod_iovec);
dep->de_read_iovec.iod_iovec_s = mp->DL_COUNT;
dep->de_read_iovec.iod_iovec_addr = (vir_bytes) mp->DL_ADDR;
size = calc_iovec_size(&dep->de_read_iovec);
} else {
dep->de_read_iovec.iod_iovec[0].iov_addr = (vir_bytes) mp->DL_ADDR;
dep->de_read_iovec.iod_iovec[0].iov_size = size = mp->DL_COUNT;
dep->de_read_iovec.iod_iovec_s = 1;
dep->de_read_iovec.iod_iovec_addr = 0;
}
if (size < ETH_MAX_PACK_SIZE) panic(dep->de_name, SizeErrMsg, size);
dep->de_flags |= DEF_READING;
(*dep->de_recvf) (dep, FALSE, size);
#if 0
if ((dep->de_flags & (DEF_READING | DEF_STOPPED)) == (DEF_READING | DEF_STOPPED))
/* The chip is stopped, and all arrived packets delivered */
(*dep->de_resetf) (dep);
dep->de_flags &= NOT(DEF_STOPPED);
#endif
}
reply(dep, OK);
return;
}
/*
** Name: void do_getstat(message *mp)
** Function: Reports device statistics.
*/
static void do_getstat(message * mp)
{
int port, rc;
dpeth_t *dep;
port = mp->DL_PORT;
if (port < 0 || port >= DE_PORT_NR) /* Check for illegal port number */
panic(dep->de_name, PortErrMsg, port);
dep = &de_table[port];
dep->de_client = mp->DL_PROC;
if (dep->de_mode == DEM_ENABLED) (*dep->de_getstatsf) (dep);
if ((rc = sys_datacopy(SELF, (vir_bytes)&dep->de_stat,
mp->DL_PROC, (vir_bytes)mp->DL_ADDR,
(vir_bytes) sizeof(dep->de_stat))) != OK)
panic(DevName, CopyErrMsg, rc);
reply(dep, OK);
return;
}
/*
** Name: void do_stop(message *mp)
** Function: Stops network interface.
*/
static void do_stop(message * mp)
{
int port;
dpeth_t *dep;
port = mp->DL_PORT;
if (port < 0 || port >= DE_PORT_NR) /* Check for illegal port number */
panic(dep->de_name, PortErrMsg, port);
dep = &de_table[port];
if (dep->de_mode == DEM_ENABLED && (dep->de_flags & DEF_ENABLED)) {
/* Stop device */
(dep->de_stopf) (dep);
dep->de_flags = DEF_EMPTY;
dep->de_mode = DEM_DISABLED;
}
return;
}
static void do_watchdog(void *message)
{
DEBUG(printf("\t no reply"));
return;
}
/*
** Name: int dpeth_task(void)
** Function: Main entry for dp task
*/
PUBLIC int main(void)
{
message m;
dpeth_t *dep;
int rc, fkeys, sfkeys;
/* Get precess number */
if ((rc = getprocnr(&dpeth_tasknr)) != OK)
panic(DevName, "getprocnr() failed", rc);
#if defined USE_IOPL
/* Request direct access to hardware I/O ports */
if ((rc = sys_enable_iop(dpeth_tasknr)) != OK)
panic(DevName, "sys_enable_iop() failed", rc);
#endif
/* Request function key for debug dumps */
fkeys = sfkeys = 0; bit_set(sfkeys, 8);
if ((fkey_map(&fkeys, &sfkeys)) != OK)
printf("%s: couldn't program Shift+F8 key (%d)\n", DevName, errno);
#ifdef ETH_IGN_PROTO
{
static u16_t eth_ign_proto = 0;
long val;
val = 0xFFFF;
env_parse("ETH_IGN_PROTO", "x", 0, &val, 0x0000L, 0xFFFFL);
eth_ign_proto = htons((u16_t) val);
}
#endif
printf("DPETH: ethernet driver task initialized (process No. %d)\n", dpeth_tasknr);
while (TRUE) {
if ((rc = receive(ANY, &m)) != OK) panic(dep->de_name, RecvErrMsg, rc);
DEBUG(printf("eth: got message %d, ", m.m_type));
switch (m.m_type) {
case DL_WRITE: /* Write message to device */
do_vwrite(&m, FALSE);
break;
case DL_WRITEV: /* Write message to device */
do_vwrite(&m, TRUE);
break;
case DL_READ: /* Read message from device */
do_vread(&m, FALSE);
break;
case DL_READV: /* Read message from device */
do_vread(&m, TRUE);
break;
case DL_INIT: /* Initialize device */
do_init(&m);
break;
case DL_GETSTAT: /* Get device statistics */
do_getstat(&m);
break;
case SYN_ALARM: /* to be defined */
do_watchdog(&m);
break;
case DL_STOP: /* Stop device */
do_stop(&m);
break;
case SYS_EVENT: {
sigset_t sigset = m.NOTIFY_ARG;
if (sigismember(&sigset, SIGKSTOP)) { /* Shut down */
for (rc = 0; rc < DE_PORT_NR; rc += 1) {
if (de_table[rc].de_mode == DEM_ENABLED) {
m.m_type = DL_STOP;
m.DL_PORT = rc;
do_stop(&m);
}
}
}
break;
}
case HARD_INT: /* Interrupt from device */
for (dep = de_table; dep < &de_table[DE_PORT_NR]; dep += 1) {
/* If device is enabled and interrupt pending */
if (dep->de_mode == DEM_ENABLED) {
/* dep->de_int_pending = FALSE; */
(*dep->de_interruptf) (dep);
if (dep->de_flags & (DEF_ACK_SEND | DEF_ACK_RECV))
reply(dep, OK);
/* enable_irq(&dep->de_hook); */
}
}
break;
case FKEY_PRESSED: /* Function key pressed */
do_dump(&m);
break;
default: /* Invalid message type */
panic(DevName, TypeErrMsg, m.m_type);
break;
}
}
return OK; /* Never reached, but keeps compiler happy */
}
#else
int main(void) { return 0; }
#endif /* ENABLE_NETWORKING */
/** dp.c **/