394 lines
11 KiB
C
394 lines
11 KiB
C
/* $NetBSD: 3c509.h,v 1.6 2006/11/24 22:52:16 wiz Exp $ */
|
|
|
|
/*
|
|
* Copyright (c) 1993 Herb Peyerl
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. The name of the author may not be used to endorse or promote products
|
|
* derived from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
|
|
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
|
|
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
|
|
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
|
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
|
|
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
|
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
|
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
* if_epreg.h,v 1.4 1994/11/13 10:12:37 gibbs Exp Modified by:
|
|
*
|
|
October 2, 1994
|
|
|
|
Modified by: Andres Vega Garcia
|
|
|
|
INRIA - Sophia Antipolis, France
|
|
e-mail: avega@sophia.inria.fr
|
|
finger: avega@pax.inria.fr
|
|
|
|
*/
|
|
|
|
/*
|
|
* Ethernet software status per interface.
|
|
*/
|
|
/*
|
|
* Some global constants
|
|
*/
|
|
#define ETHER_MIN_LEN 64
|
|
#define ETHER_MAX_LEN 1518
|
|
#define ETHER_ADDR_LEN 6
|
|
|
|
#define TX_INIT_RATE 16
|
|
#define TX_INIT_MAX_RATE 64
|
|
#define RX_INIT_LATENCY 64
|
|
#define RX_INIT_EARLY_THRESH 64
|
|
#define MIN_RX_EARLY_THRESHF 16 /* not less than ether_header */
|
|
#define MIN_RX_EARLY_THRESHL 4
|
|
|
|
#define EEPROMSIZE 0x40
|
|
#define MAX_EEPROMBUSY 1000
|
|
#define EP_LAST_TAG 0xd7
|
|
#define EP_MAX_BOARDS 16
|
|
#define EP_ID_PORT 0x100
|
|
|
|
/*
|
|
* some macros to acces long named fields
|
|
*/
|
|
#define IS_BASE (eth_base)
|
|
#define BASE (eth_base)
|
|
|
|
/*
|
|
* Commands to read/write EEPROM through EEPROM command register (Window 0,
|
|
* Offset 0xa)
|
|
*/
|
|
#define EEPROM_CMD_RD 0x0080 /* Read: Address required (5 bits) */
|
|
#define EEPROM_CMD_WR 0x0040 /* Write: Address required (5 bits) */
|
|
#define EEPROM_CMD_ERASE 0x00c0 /* Erase: Address required (5 bits) */
|
|
#define EEPROM_CMD_EWEN 0x0030 /* Erase/Write Enable: No data required */
|
|
|
|
#define EEPROM_BUSY (1<<15)
|
|
#define EEPROM_TST_MODE (1<<14)
|
|
|
|
/*
|
|
* Some short functions, worth to let them be a macro
|
|
*/
|
|
#define is_eeprom_busy(b) (inw((b)+EP_W0_EEPROM_COMMAND)&EEPROM_BUSY)
|
|
#define GO_WINDOW(x) outw(BASE+EP_COMMAND, WINDOW_SELECT|(x))
|
|
|
|
/**************************************************************************
|
|
* *
|
|
* These define the EEPROM data structure. They are used in the probe
|
|
* function to verify the existence of the adapter after having sent
|
|
* the ID_Sequence.
|
|
*
|
|
* There are others but only the ones we use are defined here.
|
|
*
|
|
**************************************************************************/
|
|
|
|
#define EEPROM_NODE_ADDR_0 0x0 /* Word */
|
|
#define EEPROM_NODE_ADDR_1 0x1 /* Word */
|
|
#define EEPROM_NODE_ADDR_2 0x2 /* Word */
|
|
#define EEPROM_PROD_ID 0x3 /* 0x9[0-f]50 */
|
|
#define EEPROM_MFG_ID 0x7 /* 0x6d50 */
|
|
#define EEPROM_ADDR_CFG 0x8 /* Base addr */
|
|
#define EEPROM_RESOURCE_CFG 0x9 /* IRQ. Bits 12-15 */
|
|
|
|
/**************************************************************************
|
|
* *
|
|
* These are the registers for the 3Com 3c509 and their bit patterns when *
|
|
* applicable. They have been taken out of the "EtherLink III Parallel *
|
|
* Tasking EISA and ISA Technical Reference" "Beta Draft 10/30/92" manual *
|
|
* from 3com. *
|
|
* *
|
|
**************************************************************************/
|
|
|
|
#define EP_COMMAND 0x0e /* Write. BASE+0x0e is always a
|
|
* command reg. */
|
|
#define EP_STATUS 0x0e /* Read. BASE+0x0e is always status
|
|
* reg. */
|
|
#define EP_WINDOW 0x0f /* Read. BASE+0x0f is always window
|
|
* reg. */
|
|
/*
|
|
* Window 0 registers. Setup.
|
|
*/
|
|
/* Write */
|
|
#define EP_W0_EEPROM_DATA 0x0c
|
|
#define EP_W0_EEPROM_COMMAND 0x0a
|
|
#define EP_W0_RESOURCE_CFG 0x08
|
|
#define EP_W0_ADDRESS_CFG 0x06
|
|
#define EP_W0_CONFIG_CTRL 0x04
|
|
/* Read */
|
|
#define EP_W0_PRODUCT_ID 0x02
|
|
#define EP_W0_MFG_ID 0x00
|
|
|
|
/*
|
|
* Window 1 registers. Operating Set.
|
|
*/
|
|
/* Write */
|
|
#define EP_W1_TX_PIO_WR_2 0x02
|
|
#define EP_W1_TX_PIO_WR_1 0x00
|
|
/* Read */
|
|
#define EP_W1_FREE_TX 0x0c
|
|
#define EP_W1_TX_STATUS 0x0b /* byte */
|
|
#define EP_W1_TIMER 0x0a /* byte */
|
|
#define EP_W1_RX_STATUS 0x08
|
|
#define EP_W1_RX_PIO_RD_2 0x02
|
|
#define EP_W1_RX_PIO_RD_1 0x00
|
|
|
|
/*
|
|
* Window 2 registers. Station Address Setup/Read
|
|
*/
|
|
/* Read/Write */
|
|
#define EP_W2_ADDR_5 0x05
|
|
#define EP_W2_ADDR_4 0x04
|
|
#define EP_W2_ADDR_3 0x03
|
|
#define EP_W2_ADDR_2 0x02
|
|
#define EP_W2_ADDR_1 0x01
|
|
#define EP_W2_ADDR_0 0x00
|
|
|
|
/*
|
|
* Window 3 registers. FIFO Management.
|
|
*/
|
|
/* Read */
|
|
#define EP_W3_FREE_TX 0x0c
|
|
#define EP_W3_FREE_RX 0x0a
|
|
|
|
/*
|
|
* Window 4 registers. Diagnostics.
|
|
*/
|
|
/* Read/Write */
|
|
#define EP_W4_MEDIA_TYPE 0x0a
|
|
#define EP_W4_CTRLR_STATUS 0x08
|
|
#define EP_W4_NET_DIAG 0x06
|
|
#define EP_W4_FIFO_DIAG 0x04
|
|
#define EP_W4_HOST_DIAG 0x02
|
|
#define EP_W4_TX_DIAG 0x00
|
|
|
|
/*
|
|
* Window 5 Registers. Results and Internal status.
|
|
*/
|
|
/* Read */
|
|
#define EP_W5_READ_0_MASK 0x0c
|
|
#define EP_W5_INTR_MASK 0x0a
|
|
#define EP_W5_RX_FILTER 0x08
|
|
#define EP_W5_RX_EARLY_THRESH 0x06
|
|
#define EP_W5_TX_AVAIL_THRESH 0x02
|
|
#define EP_W5_TX_START_THRESH 0x00
|
|
|
|
/*
|
|
* Window 6 registers. Statistics.
|
|
*/
|
|
/* Read/Write */
|
|
#define TX_TOTAL_OK 0x0c
|
|
#define RX_TOTAL_OK 0x0a
|
|
#define TX_DEFERRALS 0x08
|
|
#define RX_FRAMES_OK 0x07
|
|
#define TX_FRAMES_OK 0x06
|
|
#define RX_OVERRUNS 0x05
|
|
#define TX_COLLISIONS 0x04
|
|
#define TX_AFTER_1_COLLISION 0x03
|
|
#define TX_AFTER_X_COLLISIONS 0x02
|
|
#define TX_NO_SQE 0x01
|
|
#define TX_CD_LOST 0x00
|
|
|
|
/****************************************
|
|
*
|
|
* Register definitions.
|
|
*
|
|
****************************************/
|
|
|
|
/*
|
|
* Command register. All windows.
|
|
*
|
|
* 16 bit register.
|
|
* 15-11: 5-bit code for command to be executed.
|
|
* 10-0: 11-bit arg if any. For commands with no args;
|
|
* this can be set to anything.
|
|
*/
|
|
#define GLOBAL_RESET (u_short) 0x0000 /* Wait at least 1ms
|
|
* after issuing */
|
|
#define WINDOW_SELECT (u_short) (0x1<<11)
|
|
#define START_TRANSCEIVER (u_short) (0x2<<11) /* Read ADDR_CFG reg to
|
|
* determine whether
|
|
* this is needed. If
|
|
* so; wait 800 uSec
|
|
* before using trans-
|
|
* ceiver. */
|
|
#define RX_DISABLE (u_short) (0x3<<11) /* state disabled on
|
|
* power-up */
|
|
#define RX_ENABLE (u_short) (0x4<<11)
|
|
#define RX_RESET (u_short) (0x5<<11)
|
|
#define RX_DISCARD_TOP_PACK (u_short) (0x8<<11)
|
|
#define TX_ENABLE (u_short) (0x9<<11)
|
|
#define TX_DISABLE (u_short) (0xa<<11)
|
|
#define TX_RESET (u_short) (0xb<<11)
|
|
#define REQ_INTR (u_short) (0xc<<11)
|
|
#define SET_INTR_MASK (u_short) (0xe<<11)
|
|
#define SET_RD_0_MASK (u_short) (0xf<<11)
|
|
#define SET_RX_FILTER (u_short) (0x10<<11)
|
|
#define FIL_INDIVIDUAL (u_short) (0x1)
|
|
#define FIL_GROUP (u_short) (0x2)
|
|
#define FIL_BRDCST (u_short) (0x4)
|
|
#define FIL_ALL (u_short) (0x8)
|
|
#define SET_RX_EARLY_THRESH (u_short) (0x11<<11)
|
|
#define SET_TX_AVAIL_THRESH (u_short) (0x12<<11)
|
|
#define SET_TX_START_THRESH (u_short) (0x13<<11)
|
|
#define STATS_ENABLE (u_short) (0x15<<11)
|
|
#define STATS_DISABLE (u_short) (0x16<<11)
|
|
#define STOP_TRANSCEIVER (u_short) (0x17<<11)
|
|
/*
|
|
* The following C_* acknowledge the various interrupts. Some of them don't
|
|
* do anything. See the manual.
|
|
*/
|
|
#define ACK_INTR (u_short) (0x6800)
|
|
#define C_INTR_LATCH (u_short) (ACK_INTR|0x1)
|
|
#define C_CARD_FAILURE (u_short) (ACK_INTR|0x2)
|
|
#define C_TX_COMPLETE (u_short) (ACK_INTR|0x4)
|
|
#define C_TX_AVAIL (u_short) (ACK_INTR|0x8)
|
|
#define C_RX_COMPLETE (u_short) (ACK_INTR|0x10)
|
|
#define C_RX_EARLY (u_short) (ACK_INTR|0x20)
|
|
#define C_INT_RQD (u_short) (ACK_INTR|0x40)
|
|
#define C_UPD_STATS (u_short) (ACK_INTR|0x80)
|
|
|
|
/*
|
|
* Status register. All windows.
|
|
*
|
|
* 15-13: Window number(0-7).
|
|
* 12: Command_in_progress.
|
|
* 11: reserved.
|
|
* 10: reserved.
|
|
* 9: reserved.
|
|
* 8: reserved.
|
|
* 7: Update Statistics.
|
|
* 6: Interrupt Requested.
|
|
* 5: RX Early.
|
|
* 4: RX Complete.
|
|
* 3: TX Available.
|
|
* 2: TX Complete.
|
|
* 1: Adapter Failure.
|
|
* 0: Interrupt Latch.
|
|
*/
|
|
#define S_INTR_LATCH (u_short) (0x1)
|
|
#define S_CARD_FAILURE (u_short) (0x2)
|
|
#define S_TX_COMPLETE (u_short) (0x4)
|
|
#define S_TX_AVAIL (u_short) (0x8)
|
|
#define S_RX_COMPLETE (u_short) (0x10)
|
|
#define S_RX_EARLY (u_short) (0x20)
|
|
#define S_INT_RQD (u_short) (0x40)
|
|
#define S_UPD_STATS (u_short) (0x80)
|
|
#define S_5_INTS (S_CARD_FAILURE|S_TX_COMPLETE|\
|
|
S_TX_AVAIL|S_RX_COMPLETE|S_RX_EARLY)
|
|
#define S_COMMAND_IN_PROGRESS (u_short) (0x1000)
|
|
|
|
/*
|
|
* FIFO Registers.
|
|
* RX Status. Window 1/Port 08
|
|
*
|
|
* 15: Incomplete or FIFO empty.
|
|
* 14: 1: Error in RX Packet 0: Incomplete or no error.
|
|
* 13-11: Type of error.
|
|
* 1000 = Overrun.
|
|
* 1011 = Run Packet Error.
|
|
* 1100 = Alignment Error.
|
|
* 1101 = CRC Error.
|
|
* 1001 = Oversize Packet Error (>1514 bytes)
|
|
* 0010 = Dribble Bits.
|
|
* (all other error codes, no errors.)
|
|
*
|
|
* 10-0: RX Bytes (0-1514)
|
|
*/
|
|
#define ERR_RX_INCOMPLETE (u_short) (0x1<<15)
|
|
#define ERR_RX (u_short) (0x1<<14)
|
|
#define ERR_RX_OVERRUN (u_short) (0x8<<11)
|
|
#define ERR_RX_RUN_PKT (u_short) (0xb<<11)
|
|
#define ERR_RX_ALIGN (u_short) (0xc<<11)
|
|
#define ERR_RX_CRC (u_short) (0xd<<11)
|
|
#define ERR_RX_OVERSIZE (u_short) (0x9<<11)
|
|
#define ERR_RX_DRIBBLE (u_short) (0x2<<11)
|
|
|
|
/*
|
|
* FIFO Registers.
|
|
* TX Status. Window 1/Port 0B
|
|
*
|
|
* Reports the transmit status of a completed transmission. Writing this
|
|
* register pops the transmit completion stack.
|
|
*
|
|
* Window 1/Port 0x0b.
|
|
*
|
|
* 7: Complete
|
|
* 6: Interrupt on successful transmission requested.
|
|
* 5: Jabber Error (TP Only, TX Reset required. )
|
|
* 4: Underrun (TX Reset required. )
|
|
* 3: Maximum Collisions.
|
|
* 2: TX Status Overflow.
|
|
* 1-0: Undefined.
|
|
*
|
|
*/
|
|
#define TXS_COMPLETE 0x80
|
|
#define TXS_SUCCES_INTR_REQ 0x40
|
|
#define TXS_JABBER 0x20
|
|
#define TXS_UNDERRUN 0x10
|
|
#define TXS_MAX_COLLISION 0x8
|
|
#define TXS_STATUS_OVERFLOW 0x4
|
|
|
|
/*
|
|
* Configuration control register.
|
|
* Window 0/Port 04
|
|
*/
|
|
/* Read */
|
|
#define IS_AUI (1<<13)
|
|
#define IS_BNC (1<<12)
|
|
#define IS_UTP (1<<9)
|
|
/* Write */
|
|
#define ENABLE_DRQ_IRQ 0x0001
|
|
#define W0_P4_CMD_RESET_ADAPTER 0x4
|
|
#define W0_P4_CMD_ENABLE_ADAPTER 0x1
|
|
/*
|
|
* Media type and status.
|
|
* Window 4/Port 0A
|
|
*/
|
|
#define ENABLE_UTP 0xc0
|
|
#define DISABLE_UTP 0x0
|
|
|
|
/*
|
|
* Resource control register
|
|
*/
|
|
|
|
#define SET_IRQ(i) ( ((i)<<12) | 0xF00) /* set IRQ i */
|
|
|
|
/*
|
|
* Receive status register
|
|
*/
|
|
|
|
#define RX_BYTES_MASK (u_short) (0x07ff)
|
|
#define RX_ERROR 0x4000
|
|
#define RX_INCOMPLETE 0x8000
|
|
|
|
|
|
/*
|
|
* Misc defines for various things.
|
|
*/
|
|
#define ACTIVATE_ADAPTER_TO_CONFIG 0xff /* to the id_port */
|
|
#define MFG_ID 0x6d50 /* in EEPROM and W0 ADDR_CONFIG */
|
|
#define PROD_ID 0x9150
|
|
|
|
#define AUI 0x1
|
|
#define BNC 0x2
|
|
#define UTP 0x4
|
|
|
|
#define ETHER_ADDR_LEN 6
|
|
#define ETHER_MAX 1536
|
|
#define RX_BYTES_MASK (u_short) (0x07ff)
|
|
|
|
/* EISA support */
|
|
#define EP_EISA_START 0x1000
|
|
#define EP_EISA_W0 0x0c80
|