minix/drivers/tty/arch/earm/omap_serial.h
Ben Gras c8f3b10909 fix a few more minix specific warnings
. also disable stack protection feature for gcc,
	  causes build errors for pkgsrc gcc on minix

Change-Id: I1c6e2bcb4d948098d642543d7b2711284ee55c72
2013-08-27 16:16:03 +00:00

107 lines
4.3 KiB
C

#ifndef _OMAP_SERIAL_H
#define _OMAP_SERIAL_H
/* UART register map */
#define OMAP3_UART1_BASE 0x4806A000 /* UART1 physical address */
#define OMAP3_UART2_BASE 0x4806C000 /* UART2 physical address */
#define OMAP3_UART3_BASE 0x49020000 /* UART3 physical address */
/* UART registers */
#define OMAP3_THR 0 /* Transmit holding register */
#define OMAP3_RHR 0 /* Receive holding register */
#define OMAP3_DLL 0 /* Divisor latches low */
#define OMAP3_DLH 1 /* Divisor latches high */
#define OMAP3_IER 1 /* Interrupt enable register */
#define OMAP3_IIR 2 /* Interrupt identification register */
#define OMAP3_EFR 2 /* Extended features register */
#define OMAP3_FCR 2 /* FIFO control register */
#define OMAP3_LCR 3 /* Line control register */
#define OMAP3_MCR 4 /* Modem control register */
#define OMAP3_LSR 5 /* Line status register */
#define OMAP3_MSR 6 /* Modem status register */
#define OMAP3_TCR 6
#define OMAP3_MDR1 0x08 /* Mode definition register 1 */
#define OMAP3_MDR2 0x09 /* Mode definition register 2 */
#define OMAP3_SCR 0x10 /* Supplementary control register */
#define OMAP3_SSR 0x11 /* Supplementary status register */
#define OMAP3_SYSC 0x15 /* System configuration register */
#define OMAP3_SYSS 0x16 /* System status register */
/* Enhanced Features Register bits */
#define UART_EFR_ECB (1 << 4)/* Enhanced control bit */
#define UART_EFR_AUTO_CTS (1 << 6)/* auto cts enable */
#define UART_EFR_AUTO_RTS (1 << 7)/* auto rts enable */
/* Interrupt Enable Register bits */
#define UART_IER_MSI 0x08 /* Modem status interrupt */
#define UART_IER_RLSI 0x04 /* Receiver line status interrupt */
#define UART_IER_THRI 0x02 /* Transmitter holding register int. */
#define UART_IER_RDI 0x01 /* Receiver data interrupt */
/* FIFO control register */
#define OMAP_UART_FCR_RX_FIFO_TRIG_SHIFT 6
#define OMAP_UART_FCR_RX_FIFO_TRIG_MASK (0x3 << 6)
#define OMAP_UART_FCR_TX_FIFO_TRIG_SHIFT 4
#define OMAP_UART_FCR_TX_FIFO_TRIG_MASK (0x3 << 4)
#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the fifo */
#define UART_FCR_CLR_RCVR 0x02 /* Clear the RCVR FIFO */
#define UART_FCR_CLR_XMIT 0x04 /* Clear the XMIT FIFO */
/* Interrupt Identification Register bits */
#define UART_IIR_RDI 0x04 /* Data ready interrupt */
#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
#define UART_IIR_NO_INT 0x01 /* No interrupt is pending */
/* Line Control Register bits */
#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
#define UART_LCR_SBC 0x40 /* Set break control */
#define UART_LCR_EPAR 0x10 /* Even parity select */
#define UART_LCR_PARITY 0x08 /* Enable parity */
#define UART_LCR_STOP 0x04 /* Stop bits; 0=1 bit, 1=2 bits */
#define UART_LCR_WLEN5 0x00 /* Wordlength 5 bits */
#define UART_LCR_WLEN6 0x01 /* Wordlength 6 bits */
#define UART_LCR_WLEN7 0x02 /* Wordlength 7 bits */
#define UART_LCR_WLEN8 0x03 /* Wordlength 8 bits */
#define UART_LCR_CONF_MODE_A UART_LCR_DLAB /* Configuration Mode A */
#define UART_LCR_CONF_MODE_B 0xBF /* Configuration Mode B */
/* Line Status Register bits */
#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */
#define UART_LSR_BI 0x10 /* Break condition */
#define UART_LSR_DR 0x01 /* Data ready */
/* Modem Control Register bits */
#define UART_MCR_TCRTLR 0x40 /* Access TCR/TLR */
#define UART_MCR_OUT2 0x08 /* Out2 complement */
#define UART_MCR_RTS 0x02 /* RTS complement */
#define UART_MCR_DTR 0x01 /* DTR output low */
/* Mode Definition Register 1 bits */
#define OMAP_MDR1_DISABLE 0x07
#define OMAP_MDR1_MODE13X 0x03
#define OMAP_MDR1_MODE16X 0x00
/* Modem Status Register bits */
#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
#define UART_MSR_CTS 0x10 /* Clear to Send */
#define UART_MSR_DDCD 0x08 /* Delta DCD */
/* Supplementary control Register bits */
#define OMAP_UART_SCR_RX_TRIG_GRANU1_MASK (1 << 7)
/* System Control Register bits */
#define UART_SYSC_SOFTRESET 0x02
/* System Status Register bits */
#define UART_SYSS_RESETDONE 0x01
/* Line status register fields */
#define OMAP3_LSR_TX_FIFO_E (1 << 5) /* Transmit FIFO empty */
#define OMAP3_LSR_RX_FIFO_E (1 << 0) /* Receive FIFO empty */
#define OMAP3_LSR_RXOE (1 << 1) /* Overrun error.*/
/* Supplementary status register fields */
#define OMAP3_SSR_TX_FIFO_FULL (1 << 0) /* Transmit FIFO full */
#endif /* _OMAP_SERIAL_H */