minix/man/man2/ptrace.2
2005-05-02 13:01:42 +00:00

231 lines
5.9 KiB
Groff

.\" Copyright (c) 1980 Regents of the University of California.
.\" All rights reserved. The Berkeley software License Agreement
.\" specifies the terms and conditions for redistribution.
.\"
.\" @(#)ptrace.2 6.4 (Berkeley) 5/23/86
.\"
.TH PTRACE 2 "May 23, 1986"
.UC 4
.SH NAME
ptrace \- process trace
.SH SYNOPSIS
.nf
.ft B
#include <sys/types.h>
#include <sys/signal.h>
#include <sys/ptrace.h>
int ptrace(int \fIrequest\fP, pid_t \fIpid\fP, long \fIaddr\fP, long \fIdata\fP)
.ft R
.fi
.SH DESCRIPTION
.ft B
Note: This manual page has no relation to Minix. Someone who knows ptrace()
has to check, or rewrite, this page. (kjb)
.ft R
.PP
.B Ptrace
provides a means by which a parent process
may control the execution of a child process,
and examine and change its core image.
Its primary use is for the implementation of breakpoint debugging.
There are four arguments whose interpretation
depends on a
.I request
argument.
Generally,
.I pid
is the process ID of the traced process,
which must be a child (no more distant descendant)
of the tracing process.
A process being traced
behaves normally until it encounters some signal
whether internally generated
like \*(lqillegal instruction\*(rq or externally
generated like \*(lqinterrupt\*(rq.
See
.BR sigaction (2)
for the list.
Then the traced process enters a stopped state
and its parent is notified via
.BR wait (2).
When the child is in the stopped state,
its core image can be examined and modified
using
.BR ptrace .
If desired, another
.B ptrace
request can then cause the child either to terminate
or to continue, possibly ignoring the signal.
.PP
The value of the
.I request
argument determines the precise
action of the call:
.TP 4
PT_TRACE_ME
This request is the only one used by the child process;
it declares that the process is to be traced by its parent.
All the other arguments are ignored.
Peculiar results will ensue
if the parent does not expect to trace the child.
.TP 4
PT_READ_I, PT_READ_D
The
word in the child process's address space
at
.I addr
is returned.
If I and D space are separated (e.g. historically
on a pdp-11), request PT_READ_I indicates I space,
PT_READ_D D space.
.I Addr
must be even on some machines.
The child must be stopped.
The input
.I data
is ignored.
.TP 4
PT_READ_U
The word
of the system's per-process data area corresponding to
.I addr
is returned.
.I Addr
must be even on some machines and less than 512.
This space contains the registers and other information about
the process;
its layout corresponds to the
.I user
structure in the system.
.TP 4
PT_WRITE_I, PT_WRITE_D
The
given
.I data
is written at the word in the process's address space corresponding to
.I addr,
which must be even on some machines.
No useful value is returned.
If I and D space are separated, request PT_WRITE_I indicates I space,
PT_WRITE_D D space.
Attempts to write in pure procedure
fail if another process is executing the same file.
.TP 4
PT_WRITE_U
The process's system data is written,
as it is read with request PT_READ_U.
Only a few locations can be written in this way:
the general registers,
the floating point status and registers,
and certain bits of the processor status word.
.TP 4
PT_CONTINUE
The
.I data
argument is taken as a signal number
and the child's execution continues
at location
.I addr
as if it had incurred that signal.
Normally the signal number will be
either 0 to indicate that the signal that caused the stop
should be ignored,
or that value fetched out of the
process's image indicating which signal caused
the stop.
If
.I addr
is (int *)1 then execution continues from where it stopped.
.TP 4
PT_KILL
The traced process terminates.
.TP 4
PT_STEP
Execution continues as in request PT_CONTINUE;
however, as soon as possible after execution of at least one instruction,
execution stops again.
The signal number from the stop is
SIGTRAP.
(On the VAX-11 the T-bit is used and just one instruction
is executed.)
This is part of the mechanism for implementing breakpoints.
.PP
As indicated,
these calls
(except for request PT_TRACE_ME)
can be used only when the subject process has stopped.
The
.B wait
call is used to determine
when a process stops;
in such a case the \*(lqtermination\*(rq status
returned by
.B wait
has the value 0177 to indicate stoppage rather
than genuine termination.
.PP
To forestall possible fraud,
.B ptrace
inhibits the set-user-id and set-group-id facilities
on subsequent
.BR execve (2)
calls.
If a traced process calls
.BR execve ,
it will stop before executing the first instruction of the new image
showing signal SIGTRAP.
.PP
On a VAX-11, \*(lqword\*(rq also means a 32-bit integer,
but the \*(lqeven\*(rq
restriction does not apply.
.SH "RETURN VALUE
A 0 value is returned if the call succeeds. If the call fails
then a \-1 is returned and the global variable \fIerrno\fP is
set to indicate the error.
.SH "ERRORS
.TP 15
[EIO]
The request code is invalid.
.TP 15
[ESRCH]
The specified process does not exist.
.TP 15
[EIO]
The given signal number is invalid.
.TP 15
[EIO]
The specified address is out of bounds.
.TP 15
[EPERM]
The specified process cannot be traced.
.SH "SEE ALSO"
.BR wait (2),
.BR sigaction (2),
.BR mdb (1).
.SH BUGS
.B Ptrace
is unique and arcane; it should be replaced with a special file that
can be opened and read and written. The control functions could then
be implemented with
.BR ioctl (2)
calls on this file. This would be simpler to understand and have much
higher performance.
.PP
The request PT_TRACE_ME call should be able to specify
signals that are to be treated normally and not cause a stop.
In this way, for example,
programs with simulated floating point (which
use \*(lqillegal instruction\*(rq signals at a very high rate)
could be efficiently debugged.
.PP
The error indication, \-1, is a legitimate function value;
.BR errno ,
(see
.BR intro (2)),
can be used to disambiguate.
.PP
It should be possible to stop a process on occurrence of a system
call;
in this way a completely controlled environment could
be provided.