- change all sync char drivers into async drivers;
- retire support for the sync protocol in libchardev;
- remove async dev style, as this is now the default;
- remove dev_status from VFS;
- clean up now-unused protocol messages.
Change-Id: I6aacff712292f6b29f2ccd51bc1e7d7003723e87
BeagleBone Capes add additional hardware to the BeagleBone to
improve functionality.
This patch probes the third i2c bus for capes and loads the
appropriate drivers for each detected cape. Currently only
the 'BeagleBone Weather' cape is supported.
Change-Id: Id8c133810db6de7c21625c2d5a794b8874673a0f
Use EDID when available to configure the frame buffer driver with
good settings for the attached display.
Change-Id: I69a78155a93e55ffa1ca3ff6621a879a56cdbceb
On the BeagleBoard-xM, the RTC is located on the Power Management IC
(PMIC). To keep things consistent, access to the PMIC's RTC is done
through the readclock driver. The readclock driver forwards the request
on to the TPS65950 driver which does the work of manipulating the
registers on the chip.
Change-Id: I53cefbb59c5a9ab87fab90df3cc1a75a6e430f58
This program uses the i2c /dev interface to read the
contents of EEPROMs and display it to the user in
HEX and ASCII. It also has a mode that can display
data in label:value pairs. That mode is used for
board detection in the rc script to start the right
i2c drivers for the board.
Change-Id: I0bf5b13ffab5a89533c762d6881a145cf7f14914
To use the new SD building script, Linux has to be configured with
loop.max_part=15 on the command line (or set at module load time)
to make the loopback device see the partitions.
This commit removes a lot of differences between the ARM and x86
boot ramdisk and rc scripts. It changes the ARM build from running
from ramdisk to requiring a full filesystem on the SD image and
booting into it.
. ramdisk: remove some arm-only utilities only used for running
from the shell
. remove ARM-only rc.arm, proto.arm.small, ttys and mylogin.sh
boot-time ramdisk files
. change kernel to add "arch" variable so userland knows what
we're running on from sysenv
. make ARM use the regular ramdisk rc file, changed to distinguish
i386-only and ARM-only drivers; requires rootdevname to be set
. change /etc/rc and /usr/etc/rc to start i386-only drivers only on
i386 systems
. change the kernel/arm to have a special case for the memory
driver to load it higher so it can be bigger
. add uEnv.txt, cmdline.txt and a for now highly linux-dependent
SD preparation script arm_sdimage.sh to the git repository in
releasetools/
Change-Id: I68910ba4e96ee80f7a12b65e48b5d39b43ca6397
The rc script manually parses /etc/fstab to mount all file systems.
To do that it needs /bin/sed which does not exist anymore. mount(8)
now supports the -a flag which causes it to mount all file systems
listed in /etc/fstab except for '/'. File systems marked with 'noauto'
are skipped.
- libnetsock - internal implementation of a socket on the lwip
server side. it encapsulates the asynchronous protocol
- lwip server - uses libnetsock to work with the asynchronous
protocol
. rc script and service know to look in /usr/pkg/.. for
extra binaries and conf files
. service split into parsing config and doing RS request
so that a new utility (printconfig) can just print the
config in machine-parseable format for netconf integration
. converted all base system eth drivers/netconf
. detect both formats in /etc/rc
. generate new format in setup
. obsoletes /etc/fstab.local: everything can go in /etc/fstab
. put shutdown/reboot/halt and a copy of /usr/adm/wtmp
(/etc/wtmp) on root FS so that we can do shutdown checks before
mounting /usr
. new fstab format makes getfsent() and friends work
. add bsd-style MLINKS to minix man set, restoring aliases
(e.g. man add64 -> int64)
. update daily cron script to run makewhatis and restore makewhatis
in man Makefile (makedb), restores functionality of man -k
. netbsd imports of man, mdocml, makewhatis, libutil, apropos
. update man.conf with manpage locations, restoring man [-s] <section>
. throws out some obsolete manpages
. speeds up mkdep (i.e. world builds) significantly
. have to keep minix /bin/sed for a while because previous
usr/etc/rc depends on it
. force mkdep to use /usr/bin/sed for speedup
. use bmake for pkgsrc instead, reads mk.conf from /usr/pkg/etc/mk.conf
. tracking bmake from pkgsrc eases tracking pkgsrc
. further disentangles pkgsrc from base system, reducing maintenance
burden of pkgsrc
model to an instance-based model. Each ethernet driver instance is now
responsible for exactly one network interface card. The port field in
/etc/inet.conf now acts as an instance field instead.
This patch also updates the data link protocol. This update:
- eliminates the concept of ports entirely;
- eliminates DL_GETNAME entirely;
- standardizes on using m_source for IPC and DL_ENDPT for safecopies;
- removes error codes from TASK/STAT replies, as they were unused;
- removes a number of other old or unused fields;
- names and renames a few other fields.
All ethernet drivers have been changed to:
- conform to the new protocol, and exactly that;
- take on an instance number based on a given "instance" argument;
- skip that number of PCI devices in probe iterations;
- use config tables and environment variables based on that number;
- no longer be limited to a predefined maximum of cards in any way;
- get rid of any leftover non-safecopy support and other ancient junk;
- have a correct banner protocol figure, or none at all.
Other changes:
* Inet.conf is now taken to be line-based, and supports #-comments.
No existing installations are expected to be affected by this.
* A new, select-based asynchio library replaces the old one.
Kindly contributed by Kees J. Bot.
* Inet now supports use of select() on IP devices.
Combined, the last two changes together speed up dhcpd
considerably in the presence of multiple interfaces.
* A small bug has been fixed in nonamed.
VFS CHANGES:
- dmap table no longer statically initialized in VFS
- Dropped FSSIGNON svrctl call no longer used by INET
INET CHANGES:
- INET announces its presence to VFS just like any other driver
RS CHANGES:
- The boot image dev table contains all the data to initialize VFS' dmap table
- RS interface supports asynchronous up and update operations now
- RS interface extended to support driver style and flags
SYSLIB CHANGES:
- DS calls to publish / retrieve labels consider endpoints instead of u32_t.
VFS CHANGES:
- mapdriver() only adds an entry in the dmap table in VFS.
- dev_up() is only executed upon reception of a driver up event.
INET CHANGES:
- INET no longer searches for existing drivers instances at startup.
- A newtwork driver is (re)initialized upon reception of a driver up event.
- Networking startup is now race-free by design. No need to waste 5 seconds
at startup any more.
DRIVER CHANGES:
- Every driver publishes driver up events when starting for the first time or
in case of restart when recovery actions must be taken in the upper layers.
- Driver up events are published by drivers through DS.
- For regular drivers, VFS is normally the only subscriber, but not necessarily.
For instance, when the filter driver is in use, it must subscribe to driver
up events to initiate recovery.
- For network drivers, inet is the only subscriber for now.
- Every VFS driver is statically linked with libdriver, every network driver
is statically linked with libnetdriver.
DRIVER LIBRARIES CHANGES:
- Libdriver is extended to provide generic receive() and ds_publish() interfaces
for VFS drivers.
- driver_receive() is a wrapper for sef_receive() also used in driver_task()
to discard spurious messages that were meant to be delivered to a previous
version of the driver.
- driver_receive_mq() is the same as driver_receive() but integrates support
for queued messages.
- driver_announce() publishes a driver up event for VFS drivers and marks
the driver as initialized and expecting a DEV_OPEN message.
- Libnetdriver is introduced to provide similar receive() and ds_publish()
interfaces for network drivers (netdriver_announce() and netdriver_receive()).
- Network drivers all support live update with no state transfer now.
KERNEL CHANGES:
- Added kernel call statectl for state management. Used by driver_announce() to
unblock eventual callers sendrecing to the driver.
