readclock:
- the setup function for readclock on i386 was missing a return.
- the message field for RTCDEV_GRANT wasn't the right type.
tda19988:
- position variable was used without being initialized.
Change-Id: I3f78dd0a9d44f35eb38cb7da0974909f066b7007
On the BeagleBoard-xM, the RTC is located on the Power Management IC
(PMIC). To keep things consistent, access to the PMIC's RTC is done
through the readclock driver. The readclock driver forwards the request
on to the TPS65950 driver which does the work of manipulating the
registers on the chip.
Change-Id: I53cefbb59c5a9ab87fab90df3cc1a75a6e430f58
. Replace 64bit funcions with operators in arch_clock.c
. Replace 64bit funcions with operators in proc.c
. Replace 64bit funcions with operators in vbox.c
. Replace 64bit funcions with operators in driver.c
. Eradicates is_zero64, make_zero64, neg64
Change-Id: Ie4e1242a73534f114725271b2e2365b2004cb7b9
Add support for getting/setting the am335x SoC's internal real
time clock. Also, allow the power off alarm to be set.
Make readclock an "always on" driver. This is needed for setting
power-off alarms whenever the power button is pressed on the BBB.
Replace the readclock.sh script & single run driver with a
readclock program that takes the same arguments and forwards
the requests on to the always up readclock driver.
Change-Id: Ifd6c2acd80ae4b5e79d83df510df445c24e24a71
128 byte reads are much more common than 32 byte reads. The message
passing + setup/teardown for a read is much more expensive, in terms
of time, than the reading itself. A slightly bigger struct is well
worth the time savings. This reduces read times for /dev/eeprom
from 57 seconds per 4KB to 14 seconds.
Additionally, make sending the page address in the eeprom driver
and utility optional. This can save a little time when reading
within the same page and allows support for smaller devices that
don't support pages (example: chips containing EDID).
Change-Id: Ie48087caee40c11fa241d1555fce9309ddd27b43
This reverts commit 85e7d849c8.
This introduce a bug in position computing for disk bigger than 4GB.
Change-Id: I281e60e9644d995cc4643006b50c05693f939b44
When we send MMC commads that contain data the controller provides no
description of the order of events and we need to be able to send data
from and to the controller "when needed". Changed the code to react
on buffer read and buffer write ready based on interrupts.
Change-Id: I60c9140bf0e45b74be6475054564d4e1bd89f21e
Generalize the usage of mmc_send_cmd function to allow
it to transfer data and remove direct invocations to
mmchs_send_cmd.
Change-Id: Iabb9a7d3f4ec57536407b369531ded2b8b649cce
Clock configuration will be needed by other/future subsystems such as i2c.
Extract the functionality from libgpio and put it into it's own library.
Change-Id: I6f6de0b3fb4d305ddfeac74123b78c983d1318dd
. always keep reading data from uart so the interrupt is
not continually asserted if data is sent but no process
reads it
. increase tx & rx fifo trigger levels -> reduces the number
of interrupts necessary
. bigger rx/tx buffers
Change-Id: I3cf7c73b22ae2fc091b845d516ba4aa53e892cda
. ignore interrupt (stop interrupt check loop) if
interrupt bit not set; limit loop too
. mask off other bits when testing bits in the status register
. this fixes rs232 output that would otherwise never get re-triggered
as too many bits were set in the status byte to match the
possibilities.
Change-Id: I311c93377fa8fb477ee9a756455fdeda780e6ba1
kernel: stop gathering timestamps once the bin is full per interrupt
random: once seeded, retrieve new entropy at a lower rate
Change-Id: I4ce6081d39274728d82c6889686d1650cfd5fc2e
. add receive hooks in the kernel to print asynchronously
delivered messages
. do not rely on MF_REPLY_PEND to decide between calls and errors,
as that isn't reliable for asynchronous messages; try both instead
. add _sendcall() that extract-mfield.sh can then reliably recognize
the fields for messages that are sent with just send()
. add DEBUG_DUMPIPC_NAMES to restrict printed messages to
from/to given process names
Change-Id: Ia65eb02a69a2b58e73bf9f009987be06dda774a3
The kernel API for requesting interrupts and the associated callback
have a somewhat strange behaviour. Requesting an interrupts is done
by calling sys_irqsetpolicy using an interrupt and a given id. This
id can be modified by the sys_irqsetpolicy and must be used for
subsequent calls to sys_irqenable/sys_irqdisable. However upon an
incoming call from the kernel NOTIFY_ARG contains the original value
encoded in a set e.g. if 1 << id == true the interrupt was raised.
In order to make it more clear that ticks should be used for timers
and realtime should be used for timestamps / displaying the date/time,
getuptime() was renamed to getticks() and getuptime2() was renamed to
getuptime().
Servers, drivers, libraries, tests, etc that use getuptime()/getuptime2()
have been updated. In instances where a realtime was calculated, the
calculation was changed to use realtime.
System calls clock_getres() and clock_gettime() were added to PM/libc.
To use the new SD building script, Linux has to be configured with
loop.max_part=15 on the command line (or set at module load time)
to make the loopback device see the partitions.
This commit removes a lot of differences between the ARM and x86
boot ramdisk and rc scripts. It changes the ARM build from running
from ramdisk to requiring a full filesystem on the SD image and
booting into it.
. ramdisk: remove some arm-only utilities only used for running
from the shell
. remove ARM-only rc.arm, proto.arm.small, ttys and mylogin.sh
boot-time ramdisk files
. change kernel to add "arch" variable so userland knows what
we're running on from sysenv
. make ARM use the regular ramdisk rc file, changed to distinguish
i386-only and ARM-only drivers; requires rootdevname to be set
. change /etc/rc and /usr/etc/rc to start i386-only drivers only on
i386 systems
. change the kernel/arm to have a special case for the memory
driver to load it higher so it can be bigger
. add uEnv.txt, cmdline.txt and a for now highly linux-dependent
SD preparation script arm_sdimage.sh to the git repository in
releasetools/
Change-Id: I68910ba4e96ee80f7a12b65e48b5d39b43ca6397
