- this patch only renames schedcheck() to switch_to_user(),
cycles_accounting_stop() to context_stop() and restart() to
+restore_user_context()
- the motivation is that since the introduction of schedcheck() it has
been abused for many things. It deserves a better name. It should
express the fact that from the moment we call the function we are in
the process of switching to user.
- cycles_accounting_stop() was originally a single purpose function.
As this function is called at were convenient places it is used in
for other things too, e.g. (un)locking the kernel. Thus it deserves
a better name too.
- using the old name, restart() does not call schedcheck(), however
calls to restart are replaced by calls to schedcheck()
[switch_to_user] and it calls restart() [restore_user_context]
model to an instance-based model. Each ethernet driver instance is now
responsible for exactly one network interface card. The port field in
/etc/inet.conf now acts as an instance field instead.
This patch also updates the data link protocol. This update:
- eliminates the concept of ports entirely;
- eliminates DL_GETNAME entirely;
- standardizes on using m_source for IPC and DL_ENDPT for safecopies;
- removes error codes from TASK/STAT replies, as they were unused;
- removes a number of other old or unused fields;
- names and renames a few other fields.
All ethernet drivers have been changed to:
- conform to the new protocol, and exactly that;
- take on an instance number based on a given "instance" argument;
- skip that number of PCI devices in probe iterations;
- use config tables and environment variables based on that number;
- no longer be limited to a predefined maximum of cards in any way;
- get rid of any leftover non-safecopy support and other ancient junk;
- have a correct banner protocol figure, or none at all.
Other changes:
* Inet.conf is now taken to be line-based, and supports #-comments.
No existing installations are expected to be affected by this.
* A new, select-based asynchio library replaces the old one.
Kindly contributed by Kees J. Bot.
* Inet now supports use of select() on IP devices.
Combined, the last two changes together speed up dhcpd
considerably in the presence of multiple interfaces.
* A small bug has been fixed in nonamed.
- this panic may be unnecessarily triggered if PM gets the delayed
stop signal from kernel before it gets reply from VFS to the UNPAUSE
call.
- after this change PM does not proceed to delivering the signal until
the reply from VFS is received. Perhaps PM could deliver the signal
straight away as it knows that the process does not run. Possibly
i dangerous.
- the signal is deliverd immediately after the UNPAUSE reply as the
pending signals are always checked at the moment.
it does this by
- making all processes interruptible by running out of quantum
- giving all processes a single tick of quantum
- picking a random runnable process instead of in order, and
from a single pool of runnable processes (no priorities)
This together with very high HZ values currently provokes some race conditions
seen earlier only when running with SMP.
- rs does not assume hz==60
- rs adjusts its timeout ticks by the system clock frequency
- drivers have time to reply if hz is set too high (e.g. 1000+) for
instance when debugging
- this patch substitutes *xpp for sender to increase readability of
mini_receive().
- makes sure that the dequeued sender has p_q_link == NULL and that
this condition holds when enqueuing the sender again.
- it is a sanity check to make sure that the new sender is not
enqueued already. Before this change the dequeued sender's p_q_link
may not be NULL and it was only set to NULL when enqueued again.
A new call to vm lets processes yield a part of their memory to vm,
together with an id, getting newly allocated memory in return. vm is
allowed to forget about it if it runs out of memory. processes can ask
for it back using the same id. (These two operations are normally
combined in a single call.)
It can be used as a as-big-as-memory-will-allow block cache for
filesystems, which is how mfs now uses it.
- deadlock() is more verbose in case of a detected deadlock. First, it
lists all processses in the deadlock group. Then it prints the proc
extra info, not only stack trace and register dump
- this patch moves the former printslot() from arch_system.c to
debug.c and reimplements it slightly. The output is not changed,
however, the process information is printed in a separate function
print_proc() in debug.c as such a function is also handy in other
situations and should be publicly available when debugging.
