To map kernel we use 1M sections therefore we should use
ARM_VM_SECTION_MASK to determine base address.
Change-Id: I0b97fe459f2325d702aad9b7b1e8e066d9721b87
. Replace 64bit funcions with operators in arch_clock.c
. Replace 64bit funcions with operators in proc.c
. Replace 64bit funcions with operators in vbox.c
. Replace 64bit funcions with operators in driver.c
. Eradicates is_zero64, make_zero64, neg64
Change-Id: Ie4e1242a73534f114725271b2e2365b2004cb7b9
AM335X SoCs support power-off via a power management
chip (PMIC). An alarm in the real time clock is used
to trigger the PMIC to cut the power.
To ensure the alarm goes off when the system is in
a safe state, the RTC is frozen when the alarm is
set. At the last moment, the kernel unfreezes the RTC
to let the alarm go off.
This patch adds a mini driver for unfreezing the RTC
as well as code to handle RBT_POWEROFF on Minix/arm.
Change-Id: I7d48e75791e3a81bdd2f7704997193a269409fe8
The padconf library runs in user mode, but to actually affect the
padconf register contents, the processor has to be in privileged
mode. A full server based solution will be developed, but for now
just set the pinmux in the kernel at boot.
Change-Id: I170ed54dae64b27cd9bd8807445231598fb8e3e1
Implement getrusage.
These fields of struct rusage are not supported and always set to zero at this time
long ru_nswap; /* swaps */
long ru_inblock; /* block input operations */
long ru_oublock; /* block output operations */
long ru_msgsnd; /* messages sent */
long ru_msgrcv; /* messages received */
long ru_nvcsw; /* voluntary context switches */
long ru_nivcsw; /* involuntary context switches */
test75.c is the unit test for this new function
Change-Id: I3f1eb69de1fce90d087d76773b09021fc6106539
. with hz=1000, clock_t only lasts a few years.
whenever we can't express the desired realtime
in ticks because the distance with boottime is
too high, simply adjust bootime like we do for
otherwise negative values.
. fixes test 2 on ARM
kernel:
. modules can be as big as the space (8MB) between them
instead of 4MB; memory is slightly bigger with DBG=-g
arm ucontext:
. r4 is clobbered by the restore function, as it's
used as a scratch register, causing problems for the
DBG=-g build
. r1-r3 are safe for scratch registers, as they are
caller-save, so use r3 instead; and don't bother
restoring r1-r3, but preserve r4
vfs:
. improve TLL pointer sanity check a bit
Change-Id: I0e3cfc367fdc14477e40d04b5e044f288ca4cc7d
. set 'done' once initialized so 32-bit read frc works,
thanks to keesj
. make sure the software-implemented upper 32 bit of the 64-bit
"tsc" value works OK by adding an assert in one of its calls
Change-Id: I5ce24fea919f4610c6a86ac7ec9f04b1815620c2
. by making the address and frequency of the
free running clock kinfo members, set at runtime
in the kernel, instead of compile time constants
in libsys
Change-Id: I4a8387302d4d3ffd47d2448525725683a74c9a4f
Use acpi poweroff if it's possible.
Change-Id: I103cc288523bf63fa536750b1d408ac88bbe35fb
Signed-off-by: Ben Gras <ben@minix3.org>
Signed-off-by: Tomas Hruby <tom@minix3.org>
Omap timers remove hardcoded base address and add some initial
support for the beaglebone's timers. Frclock_util will need
refactoring to remain independent of the ARM flavour.
Change-Id: I2b5d04e930364262c81b5686de634c0a51796b23
Remove hardcoded base address for the omap interrupt handler and add
interrupt names for AM335X in omap_intr.h.
Change-Id: Ie606d8612f55990d55f9db655583052f53950e8e
Keep kernel and modules in the first 256MB of memory in preparation
for the beaglebone. That target only has 256 MB of memory.
Change-Id: I3d92247b5d4e5d3aab7388fe01c2f5713d6a4593
Removed hardcoded base address for in kernel serial. This will ease
porting to different boards and allow us to remap i/o at later stage.
Change-Id: I4a4e00ed2aa2f94dfe928dc43a6816d3b94576b7
Simplify the in kernel serial header to a minimum. The driver doing
the real handling is the tty driver.
Change-Id: I5d487d71a3d22906313aa8af5e9d84b0751a6868
. an instruction fetch pagefault generates a prefetch
abort exception, this should also be a source of
a pagefault event
. the saved_lr argument to the C exception handler was
sometimes an address, sometimes a pointer to that address;
the kernel sometimes dereferences it, so it should always be
an in-kernel address, never a userspace address. fix in mpx.S
makes it always a pointer.
. move dumping of all processes over serial out of
the arch-specific arch_system.c
. add receive hooks in the kernel to print asynchronously
delivered messages
. do not rely on MF_REPLY_PEND to decide between calls and errors,
as that isn't reliable for asynchronous messages; try both instead
. add _sendcall() that extract-mfield.sh can then reliably recognize
the fields for messages that are sent with just send()
. add DEBUG_DUMPIPC_NAMES to restrict printed messages to
from/to given process names
Change-Id: Ia65eb02a69a2b58e73bf9f009987be06dda774a3
The natural term to use when talking about MINIX big pages on ARM
is SECTION. A section is a level 1 page table entry pointing to
a 1MB area.
Change-Id: I9bd27ca99bc772126c31c27a537b1415db20c4a6
In libexec, split the memory allocation method into cleared and
non-cleared. Cleared gives zeroed memory, non-cleared gives 'junk'
memory (that will be overwritten anyway, and so needn't be cleared)
that is faster to get.
Also introduce the 'memmap' method that can be used, if available,
to map code and data from executables into a process using the
third-party mmap() mode.
Change-Id: I26694fd3c21deb8b97e01ed675dfc14719b0672b
We used to load the memory driver above the other modules to allow
the memory driver (ramdisk) to grow. We no longer want or need this
this as we have a working mmc driver.
This also adds the sys_settime() kernel call which allows for the adjusting
of the clock named realtime in the kernel. The existing sys_stime()
function is still needed for a separate job (setting the boottime). The
boottime is set in the readclock driver. The sys_settime() interface is
meant to be flexible and will support both clock_settime() and adjtime()
when adjtime() is implemented later.
settimeofday() was adjusted to use the clock_settime() interface.
One side note discovered during testing: uptime(1) (part of the last(1)),
uses wtmp to determine boottime (not Minix's times(2)). This leads `uptime`
to report odd results when you set the time to a time prior to boottime.
This isn't a new bug introduced by my changes. It's been there for a while.
In order to make it more clear that ticks should be used for timers
and realtime should be used for timestamps / displaying the date/time,
getuptime() was renamed to getticks() and getuptime2() was renamed to
getuptime().
Servers, drivers, libraries, tests, etc that use getuptime()/getuptime2()
have been updated. In instances where a realtime was calculated, the
calculation was changed to use realtime.
System calls clock_getres() and clock_gettime() were added to PM/libc.
Old realtime was used for both timers (where an accurate count of
all ticks is needed) and the system time. In order to implement
adjtime(2), these duties must be separated as changing the time
of day by a small amount shouldn't affect timers in any way nor
should it change the boot time.
Following the naming of the clocks used by clock_gettime(2). The
clock named 'realtime' will represent the best guess at the
current wall clock time, and the clock named 'monotonic' will
represent the absolute time the system has been running.
Use monotonic for timers in kernel and in drivers. Use realtime
for determining time of day, dates, etc.
This commit simply renames realtime to monotonic and adds a new
tick counter named realtime. There are no functional changes in
this commit. It just lays the foundation for future work.
To use the new SD building script, Linux has to be configured with
loop.max_part=15 on the command line (or set at module load time)
to make the loopback device see the partitions.
This commit removes a lot of differences between the ARM and x86
boot ramdisk and rc scripts. It changes the ARM build from running
from ramdisk to requiring a full filesystem on the SD image and
booting into it.
. ramdisk: remove some arm-only utilities only used for running
from the shell
. remove ARM-only rc.arm, proto.arm.small, ttys and mylogin.sh
boot-time ramdisk files
. change kernel to add "arch" variable so userland knows what
we're running on from sysenv
. make ARM use the regular ramdisk rc file, changed to distinguish
i386-only and ARM-only drivers; requires rootdevname to be set
. change /etc/rc and /usr/etc/rc to start i386-only drivers only on
i386 systems
. change the kernel/arm to have a special case for the memory
driver to load it higher so it can be bigger
. add uEnv.txt, cmdline.txt and a for now highly linux-dependent
SD preparation script arm_sdimage.sh to the git repository in
releasetools/
Change-Id: I68910ba4e96ee80f7a12b65e48b5d39b43ca6397
The build system distinction between "bootprog" and "service" is
meaningless as boot programs are standard services.
As minix.service.mk simply imports minix.bootprog.mk, reduce confusion
by removing minix.bootprog.mk and placing the rules in minix.service.mk.
Change-Id: I4056b1e574bed59a8c890239b41b1a7c7cad63e8
. phys_copy() (taken from memcpy) can legitimately
cause pagefaults below the source/dest address due
to word-alignment
Change-Id: Ibee8f069781d16caea671246c021fb17a2a892b1
Interrupts where not correctly masked while in kernel, which
breaks one of the current main assumptions.
Also remove some duplication on ARM asm files, and add a function
to check the status of ARM irqs (not compiled by default)
Change-Id: I3c25d2b388f93fd8fe423998b94b3c4f140ba831
