minix/drivers/printer/printer.c

422 lines
15 KiB
C
Raw Normal View History

2005-04-21 16:53:53 +02:00
/* This file contains the printer driver. It is a fairly simple driver,
* supporting only one printer. Characters that are written to the driver
* are written to the printer without any changes at all.
*
* Changes:
2005-04-29 17:36:43 +02:00
* May 07, 2004 fix: wait until printer is ready (Jorrit N. Herder)
2005-04-21 16:53:53 +02:00
* May 06, 2004 printer driver moved to user-space (Jorrit N. Herder)
*
* The valid messages and their parameters are:
*
* DEV_OPEN: initializes the printer
* DEV_CLOSE: does nothing
* HARD_INT: interrupt handler has finished current chunk of output
* DEV_WRITE: a process wants to write on a terminal
2005-06-24 18:21:54 +02:00
* CANCEL: terminate a previous incomplete system call immediately
2005-04-21 16:53:53 +02:00
*
* m_type TTY_LINE IO_ENDPT COUNT ADDRESS
2005-04-21 16:53:53 +02:00
* |-------------+---------+---------+---------+---------|
* | DEV_OPEN | | | | |
* |-------------+---------+---------+---------+---------|
* | DEV_CLOSE | | proc nr | | |
* -------------------------------------------------------
* | HARD_INT | | | | |
* |-------------+---------+---------+---------+---------|
* | SYS_EVENT | | | | |
2005-04-21 16:53:53 +02:00
* |-------------+---------+---------+---------+---------|
* | DEV_WRITE |minor dev| proc nr | count | buf ptr |
* |-------------+---------+---------+---------+---------|
* | CANCEL |minor dev| proc nr | | |
* -------------------------------------------------------
*
* Note: since only 1 printer is supported, minor dev is not used at present.
*/
#include "../drivers.h"
/* Control bits (in port_base + 2). "+" means positive logic and "-" means
* negative logic. Most of the signals are negative logic on the pins but
* many are converted to positive logic in the ports. Some manuals are
* misleading because they only document the pin logic.
*
* +0x01 Pin 1 -Strobe
* +0x02 Pin 14 -Auto Feed
* -0x04 Pin 16 -Initialize Printer
* +0x08 Pin 17 -Select Printer
* +0x10 IRQ7 Enable
*
* Auto Feed and Select Printer are always enabled. Strobe is enabled briefly
* when characters are output. Initialize Printer is enabled briefly when
* the task is started. IRQ7 is enabled when the first character is output
* and left enabled until output is completed (or later after certain
* abnormal completions).
*/
#define ASSERT_STROBE 0x1D /* strobe a character to the interface */
#define NEGATE_STROBE 0x1C /* enable interrupt on interface */
#define PR_SELECT 0x0C /* select printer bit */
2005-04-21 16:53:53 +02:00
#define INIT_PRINTER 0x08 /* init printer bits */
/* Status bits (in port_base + 2).
*
* -0x08 Pin 15 -Error
* +0x10 Pin 13 +Select Status
* +0x20 Pin 12 +Out of Paper
* -0x40 Pin 10 -Acknowledge
* -0x80 Pin 11 +Busy
*/
#define BUSY_STATUS 0x10 /* printer gives this status when busy */
#define NO_PAPER 0x20 /* status bit saying that paper is out */
#define NORMAL_STATUS 0x90 /* printer gives this status when idle */
#define ON_LINE 0x10 /* status bit saying that printer is online */
#define STATUS_MASK 0xB0 /* mask to filter out status bits */
#define MAX_ONLINE_RETRIES 120 /* about 60s: waits 0.5s after each retry */
/* Centronics interface timing that must be met by software (in microsec).
*
* Strobe length: 0.5u to 100u (not sure about the upper limit).
* Data set up: 0.5u before strobe.
* Data hold: 0.5u after strobe.
* Init pulse length: over 200u (not sure).
*
* The strobe length is about 50u with the code here and function calls for
* sys_outb() - not much to spare. The 0.5u minimums will not be violated
* with the sys_outb() messages exchanged.
*/
PRIVATE int caller; /* process to tell when printing done (FS) */
PRIVATE int revive_pending; /* set to true if revive is pending */
PRIVATE int revive_status; /* revive status */
2005-04-21 16:53:53 +02:00
PRIVATE int done_status; /* status of last output completion */
PRIVATE int oleft; /* bytes of output left in obuf */
PRIVATE char obuf[128]; /* output buffer */
PRIVATE char *optr; /* ptr to next char in obuf to print */
PRIVATE int orig_count; /* original byte count */
PRIVATE int port_base; /* I/O port for printer */
PRIVATE int proc_nr; /* user requesting the printing */
PRIVATE int user_left; /* bytes of output left in user buf */
PRIVATE vir_bytes user_vir; /* address of remainder of user buf */
PRIVATE int writing; /* nonzero while write is in progress */
2005-05-02 16:30:04 +02:00
PRIVATE int irq_hook_id; /* id of irq hook at kernel */
2005-04-21 16:53:53 +02:00
2005-06-24 18:21:54 +02:00
extern int errno; /* error number */
2005-04-21 16:53:53 +02:00
FORWARD _PROTOTYPE( void do_cancel, (message *m_ptr) );
FORWARD _PROTOTYPE( void output_done, (void) );
FORWARD _PROTOTYPE( void do_write, (message *m_ptr) );
FORWARD _PROTOTYPE( void do_status, (message *m_ptr) );
2005-04-21 16:53:53 +02:00
FORWARD _PROTOTYPE( void prepare_output, (void) );
FORWARD _PROTOTYPE( void do_initialize, (void) );
FORWARD _PROTOTYPE( void reply, (int code,int replyee,int proc,int status));
FORWARD _PROTOTYPE( void do_printer_output, (void) );
FORWARD _PROTOTYPE( void do_signal, (message *m_ptr) );
2005-06-24 18:21:54 +02:00
2005-04-21 16:53:53 +02:00
/*===========================================================================*
* printer_task *
*===========================================================================*/
PUBLIC void main(void)
{
/* Main routine of the printer task. */
message pr_mess; /* buffer for all incoming messages */
struct sigaction sa;
int s;
/* Install signal handlers. Ask PM to transform signal into message. */
sa.sa_handler = SIG_MESS;
sigemptyset(&sa.sa_mask);
sa.sa_flags = 0;
if (sigaction(SIGTERM,&sa,NULL)<0) panic("PRN","sigaction failed", errno);
2005-06-24 18:21:54 +02:00
2005-04-21 16:53:53 +02:00
while (TRUE) {
receive(ANY, &pr_mess);
switch(pr_mess.m_type) {
case DEV_OPEN:
do_initialize(); /* initialize */
/* fall through */
case DEV_CLOSE:
reply(TASK_REPLY, pr_mess.m_source, pr_mess.IO_ENDPT, OK);
2005-04-21 16:53:53 +02:00
break;
case DEV_WRITE: do_write(&pr_mess); break;
case DEV_STATUS: do_status(&pr_mess); break;
case CANCEL: do_cancel(&pr_mess); break;
case HARD_INT: do_printer_output(); break;
case SYS_SIG: do_signal(&pr_mess); break;
case DEV_PING: notify(pr_mess.m_source); break;
2006-03-16 12:22:31 +01:00
case PROC_EVENT: break;
2005-04-21 16:53:53 +02:00
default:
reply(TASK_REPLY, pr_mess.m_source, pr_mess.IO_ENDPT, EINVAL);
2005-04-21 16:53:53 +02:00
}
}
}
/*===========================================================================*
* do_signal *
*===========================================================================*/
PRIVATE void do_signal(m_ptr)
message *m_ptr; /* signal message */
{
int sig;
sigset_t sigset = m_ptr->NOTIFY_ARG;
/* Expect a SIGTERM signal when this server must shutdown. */
if (sigismember(&sigset, SIGTERM)) {
exit(0);
}
/* Ignore all other signals. */
}
2005-04-21 16:53:53 +02:00
/*===========================================================================*
* do_write *
*===========================================================================*/
PRIVATE void do_write(m_ptr)
register message *m_ptr; /* pointer to the newly arrived message */
{
/* The printer is used by sending DEV_WRITE messages to it. Process one. */
register int r = SUSPEND;
int retries;
2006-03-25 00:05:21 +01:00
unsigned long status;
2005-04-21 16:53:53 +02:00
/* Reject command if last write is not yet finished, the count is not
* positive, or the user address is bad.
*/
if (writing) r = EIO;
else if (m_ptr->COUNT <= 0) r = EINVAL;
/* Reply to FS, no matter what happened, possible SUSPEND caller. */
reply(TASK_REPLY, m_ptr->m_source, m_ptr->IO_ENDPT, r);
2005-04-21 16:53:53 +02:00
/* If no errors occurred, continue printing with SUSPENDED caller.
* First wait until the printer is online to prevent stupid errors.
*/
if (SUSPEND == r) {
caller = m_ptr->m_source;
proc_nr = m_ptr->IO_ENDPT;
2005-04-21 16:53:53 +02:00
user_left = m_ptr->COUNT;
orig_count = m_ptr->COUNT;
user_vir = (vir_bytes) m_ptr->ADDRESS;
writing = TRUE;
retries = MAX_ONLINE_RETRIES + 1;
while (--retries > 0) {
sys_inb(port_base + 1, &status);
if ((status & ON_LINE)) { /* printer online! */
prepare_output();
do_printer_output();
return;
}
tickdelay(30); /* wait before retry */
2005-04-21 16:53:53 +02:00
}
/* If we reach this point, the printer was not online in time. */
done_status = status;
output_done();
}
}
/*===========================================================================*
* output_done *
2005-04-21 16:53:53 +02:00
*===========================================================================*/
PRIVATE void output_done()
{
/* Previous chunk of printing is finished. Continue if OK and more.
* Otherwise, reply to caller (FS).
*/
register int status;
if (!writing) return; /* probably leftover interrupt */
if (done_status != OK) { /* printer error occurred */
status = EIO;
if ((done_status & ON_LINE) == 0) {
printf("Printer is not on line\n");
} else if ((done_status & NO_PAPER)) {
printf("Printer is out of paper\n");
status = EAGAIN;
} else {
printf("Printer error, status is 0x%02X\n", done_status);
}
/* Some characters have been printed, tell how many. */
if (status == EAGAIN && user_left < orig_count) {
status = orig_count - user_left;
}
oleft = 0; /* cancel further output */
}
else if (user_left != 0) { /* not yet done, continue! */
prepare_output();
return;
}
else { /* done! report back to FS */
status = orig_count;
}
revive_pending = TRUE;
revive_status = status;
notify(caller);
2005-04-21 16:53:53 +02:00
}
/*===========================================================================*
* do_status *
*===========================================================================*/
PRIVATE void do_status(m_ptr)
register message *m_ptr; /* pointer to the newly arrived message */
{
if (revive_pending) {
m_ptr->m_type = DEV_REVIVE; /* build message */
m_ptr->REP_ENDPT = proc_nr;
m_ptr->REP_STATUS = revive_status;
writing = FALSE; /* unmark event */
revive_pending = FALSE; /* unmark event */
} else {
m_ptr->m_type = DEV_NO_STATUS;
}
send(m_ptr->m_source, m_ptr); /* send the message */
}
2005-04-21 16:53:53 +02:00
/*===========================================================================*
* do_cancel *
*===========================================================================*/
PRIVATE void do_cancel(m_ptr)
register message *m_ptr; /* pointer to the newly arrived message */
{
/* Cancel a print request that has already started. Usually this means that
* the process doing the printing has been killed by a signal. It is not
* clear if there are race conditions. Try not to cancel the wrong process,
* but rely on FS to handle the EINTR reply and de-suspension properly.
*/
if (writing && m_ptr->IO_ENDPT == proc_nr) {
2005-04-21 16:53:53 +02:00
oleft = 0; /* cancel output by interrupt handler */
writing = FALSE;
revive_pending = FALSE;
2005-04-21 16:53:53 +02:00
}
reply(TASK_REPLY, m_ptr->m_source, m_ptr->IO_ENDPT, EINTR);
2005-04-21 16:53:53 +02:00
}
/*===========================================================================*
* reply *
*===========================================================================*/
PRIVATE void reply(code, replyee, process, status)
int code; /* TASK_REPLY or REVIVE */
int replyee; /* destination for message (normally FS) */
int process; /* which user requested the printing */
int status; /* number of chars printed or error code */
{
/* Send a reply telling FS that printing has started or stopped. */
message pr_mess;
pr_mess.m_type = code; /* TASK_REPLY or REVIVE */
pr_mess.REP_STATUS = status; /* count or EIO */
pr_mess.REP_ENDPT = process; /* which user does this pertain to */
2005-04-21 16:53:53 +02:00
send(replyee, &pr_mess); /* send the message */
}
/*===========================================================================*
* do_initialize *
*===========================================================================*/
PRIVATE void do_initialize()
{
/* Set global variables and initialize the printer. */
static int initialized = FALSE;
if (initialized) return;
initialized = TRUE;
2005-05-02 16:30:04 +02:00
/* Get the base port for first printer. */
2005-04-29 17:36:43 +02:00
sys_vircopy(SELF, BIOS_SEG, LPT1_IO_PORT_ADDR,
SELF, D, (vir_bytes) &port_base, LPT1_IO_PORT_SIZE);
2005-04-21 16:53:53 +02:00
sys_outb(port_base + 2, INIT_PRINTER);
tickdelay(1); /* easily satisfies Centronics minimum */
2005-04-21 16:53:53 +02:00
/* was 2 millisecs; now is ~17 millisecs */
sys_outb(port_base + 2, PR_SELECT);
irq_hook_id = 0;
2005-05-02 16:30:04 +02:00
sys_irqsetpolicy(PRINTER_IRQ, 0, &irq_hook_id);
sys_irqenable(&irq_hook_id);
2005-04-21 16:53:53 +02:00
}
/*==========================================================================*
* prepare_output *
*==========================================================================*/
PRIVATE void prepare_output()
{
/* Start next chunk of printer output. Fetch the data from user space. */
register int chunk;
if ( (chunk = user_left) > sizeof obuf) chunk = sizeof obuf;
if (OK!=sys_datacopy(proc_nr, user_vir, SELF, (vir_bytes) obuf, chunk)) {
done_status = EFAULT;
output_done();
return;
}
optr = obuf;
oleft = chunk;
}
/*===========================================================================*
* do_printer_output *
*===========================================================================*/
PRIVATE void do_printer_output()
{
/* This function does the actual output to the printer. This is called on
* a HARD_INT message sent from the generic interrupt handler that 'forwards'
* interrupts to this driver. The generic handler did not reenable the
* printer IRQ yet!
*/
2006-03-25 00:05:21 +01:00
unsigned long status;
2005-04-21 16:53:53 +02:00
pvb_pair_t char_out[3];
if (oleft == 0) {
/* Nothing more to print. Turn off printer interrupts in case they
* are level-sensitive as on the PS/2. This should be safe even
* when the printer is busy with a previous character, because the
* interrupt status does not affect the printer.
*/
sys_outb(port_base + 2, PR_SELECT);
2005-05-02 16:30:04 +02:00
sys_irqenable(&irq_hook_id);
2005-04-21 16:53:53 +02:00
return;
}
do {
/* Loop to handle fast (buffered) printers. It is important that
* processor interrupts are not disabled here, just printer interrupts.
*/
(void) sys_inb(port_base + 1, &status);
if ((status & STATUS_MASK) == BUSY_STATUS) {
/* Still busy with last output. This normally happens
* immediately after doing output to an unbuffered or slow
* printer. It may happen after a call from prepare_output or
* pr_restart, since they are not synchronized with printer
* interrupts. It may happen after a spurious interrupt.
*/
2005-05-02 16:30:04 +02:00
sys_irqenable(&irq_hook_id);
2005-04-21 16:53:53 +02:00
return;
}
if ((status & STATUS_MASK) == NORMAL_STATUS) {
/* Everything is all right. Output another character. */
pv_set(char_out[0], port_base, *optr++);
pv_set(char_out[1], port_base+2, ASSERT_STROBE);
pv_set(char_out[2], port_base+2, NEGATE_STROBE);
sys_voutb(char_out, 3); /* request series of port outb */
user_vir++;
user_left--;
} else {
/* Error. This would be better ignored (treat as busy). */
done_status = status;
output_done();
2005-05-02 16:30:04 +02:00
sys_irqenable(&irq_hook_id);
2005-04-21 16:53:53 +02:00
return;
}
}
while (--oleft != 0);
/* Finished printing chunk OK. */
done_status = OK;
output_done();
2005-05-02 16:30:04 +02:00
sys_irqenable(&irq_hook_id);
2005-04-21 16:53:53 +02:00
}