minix/kernel/arch/i386/mpx386.s

612 lines
17 KiB
ArmAsm
Raw Normal View History

#
2005-04-21 16:53:53 +02:00
! This file, mpx386.s, is included by mpx.s when Minix is compiled for
! 32-bit Intel CPUs. The alternative mpx88.s is compiled for 16-bit CPUs.
! This file is part of the lowest layer of the MINIX kernel. (The other part
! is "proc.c".) The lowest layer does process switching and message handling.
! Furthermore it contains the assembler startup code for Minix and the 32-bit
! interrupt handlers. It cooperates with the code in "start.c" to set up a
! good environment for main().
2005-04-21 16:53:53 +02:00
! Every transition to the kernel goes through this file. Transitions to the
! kernel may be nested. The initial entry may be with a system call (i.e.,
! send or receive a message), an exception or a hardware interrupt; kernel
! reentries may only be made by hardware interrupts. The count of reentries
! is kept in "k_reenter". It is important for deciding whether to switch to
! the kernel stack and for protecting the message passing code in "proc.c".
2005-04-21 16:53:53 +02:00
! For the message passing trap, most of the machine state is saved in the
! proc table. (Some of the registers need not be saved.) Then the stack is
! switched to "k_stack", and interrupts are reenabled. Finally, the system
! call handler (in C) is called. When it returns, interrupts are disabled
! again and the code falls into the restart routine, to finish off held-up
! interrupts and run the process or task whose pointer is in "proc_ptr".
! Hardware interrupt handlers do the same, except (1) The entire state must
! be saved. (2) There are too many handlers to do this inline, so the save
! routine is called. A few cycles are saved by pushing the address of the
! appropiate restart routine for a return later. (3) A stack switch is
! avoided when the stack is already switched. (4) The (master) 8259 interrupt
! controller is reenabled centrally in save(). (5) Each interrupt handler
! masks its interrupt line using the 8259 before enabling (other unmasked)
! interrupts, and unmasks it after servicing the interrupt. This limits the
! nest level to the number of lines and protects the handler from itself.
! For communication with the boot monitor at startup time some constant
! data are compiled into the beginning of the text segment. This facilitates
! reading the data at the start of the boot process, since only the first
! sector of the file needs to be read.
! Some data storage is also allocated at the end of this file. This data
! will be at the start of the data segment of the kernel and will be read
! and modified by the boot monitor before the kernel starts.
! sections
#include <sys/vm_i386.h>
2005-04-21 16:53:53 +02:00
.sect .text
begtext:
.sect .rom
begrom:
.sect .data
begdata:
.sect .bss
begbss:
#include <minix/config.h>
#include <minix/const.h>
#include <minix/com.h>
#include <ibm/interrupt.h>
Split of architecture-dependent and -independent functions for i386, mainly in the kernel and headers. This split based on work by Ingmar Alting <iaalting@cs.vu.nl> done for his Minix PowerPC architecture port. . kernel does not program the interrupt controller directly, do any other architecture-dependent operations, or contain assembly any more, but uses architecture-dependent functions in arch/$(ARCH)/. . architecture-dependent constants and types defined in arch/$(ARCH)/include. . <ibm/portio.h> moved to <minix/portio.h>, as they have become, for now, architecture-independent functions. . int86, sdevio, readbios, and iopenable are now i386-specific kernel calls and live in arch/i386/do_* now. . i386 arch now supports even less 86 code; e.g. mpx86.s and klib86.s have gone, and 'machine.protected' is gone (and always taken to be 1 in i386). If 86 support is to return, it should be a new architecture. . prototypes for the architecture-dependent functions defined in kernel/arch/$(ARCH)/*.c but used in kernel/ are in kernel/proto.h . /etc/make.conf included in makefiles and shell scripts that need to know the building architecture; it defines ARCH=<arch>, currently only i386. . some basic per-architecture build support outside of the kernel (lib) . in clock.c, only dequeue a process if it was ready . fixes for new include files files deleted: . mpx/klib.s - only for choosing between mpx/klib86 and -386 . klib86.s - only for 86 i386-specific files files moved (or arch-dependent stuff moved) to arch/i386/: . mpx386.s (entry point) . klib386.s . sconst.h . exception.c . protect.c . protect.h . i8269.c
2006-12-22 16:22:27 +01:00
#include <archconst.h>
#include "../../const.h"
2005-04-21 16:53:53 +02:00
#include "sconst.h"
/* Selected 386 tss offsets. */
#define TSS3_S_SP0 4
! Exported functions
! Note: in assembly language the .define statement applied to a function name
! is loosely equivalent to a prototype in C code -- it makes it possible to
! link to an entity declared in the assembly code but does not create
! the entity.
.define _restart
.define save
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
.define _reload_cr3
.define _write_cr3 ! write cr3
.define errexception
.define exception1
.define exception
2005-04-21 16:53:53 +02:00
.define _divide_error
.define _single_step_exception
.define _nmi
.define _breakpoint_exception
.define _overflow
.define _bounds_check
.define _inval_opcode
.define _copr_not_available
.define _double_fault
.define _copr_seg_overrun
.define _inval_tss
.define _segment_not_present
.define _stack_exception
.define _general_protection
.define _page_fault
.define _copr_error
.define _params_size
.define _params_offset
.define _mon_ds
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
.define _schedcheck
.define _dirtypde
2005-04-21 16:53:53 +02:00
.define _hwint00 ! handlers for hardware interrupts
.define _hwint01
.define _hwint02
.define _hwint03
.define _hwint04
.define _hwint05
.define _hwint06
.define _hwint07
.define _hwint08
.define _hwint09
.define _hwint10
.define _hwint11
.define _hwint12
.define _hwint13
.define _hwint14
.define _hwint15
.define _s_call
.define _p_s_call
.define _level0_call
! Exported variables.
.define begbss
.define begdata
.sect .text
!*===========================================================================*
!* MINIX *
!*===========================================================================*
MINIX: ! this is the entry point for the MINIX kernel
jmp over_flags ! skip over the next few bytes
.data2 CLICK_SHIFT ! for the monitor: memory granularity
flags:
.data2 0x01FD ! boot monitor flags:
! call in 386 mode, make bss, make stack,
2005-09-07 20:15:21 +02:00
! load high, don't patch, will return,
2005-04-21 16:53:53 +02:00
! uses generic INT, memory vector,
! new boot code return
nop ! extra byte to sync up disassembler
over_flags:
! Set up a C stack frame on the monitor stack. (The monitor sets cs and ds
! right. The ss descriptor still references the monitor data segment.)
movzx esp, sp ! monitor stack is a 16 bit stack
push ebp
mov ebp, esp
push esi
push edi
cmp 4(ebp), 0 ! monitor return vector is
jz noret ! nonzero if return possible
inc (_mon_return)
noret: mov (_mon_sp), esp ! save stack pointer for later return
! Copy the monitor global descriptor table to the address space of kernel and
! switch over to it. Prot_init() can then update it with immediate effect.
sgdt (_gdt+GDT_SELECTOR) ! get the monitor gdtr
mov esi, (_gdt+GDT_SELECTOR+2) ! absolute address of GDT
mov ebx, _gdt ! address of kernel GDT
mov ecx, 8*8 ! copying eight descriptors
copygdt:
eseg movb al, (esi)
movb (ebx), al
inc esi
inc ebx
loop copygdt
mov eax, (_gdt+DS_SELECTOR+2) ! base of kernel data
and eax, 0x00FFFFFF ! only 24 bits
add eax, _gdt ! eax = vir2phys(gdt)
mov (_gdt+GDT_SELECTOR+2), eax ! set base of GDT
lgdt (_gdt+GDT_SELECTOR) ! switch over to kernel GDT
! Locate boot parameters, set up kernel segment registers and stack.
mov ebx, 8(ebp) ! boot parameters offset
mov edx, 12(ebp) ! boot parameters length
mov eax, 16(ebp) ! address of a.out headers
mov (_aout), eax
mov ax, ds ! kernel data
mov es, ax
mov fs, ax
mov gs, ax
mov ss, ax
mov esp, k_stktop ! set sp to point to the top of kernel stack
! Save boot parameters into these global variables for i386 code
mov (_params_size), edx
mov (_params_offset), ebx
mov (_mon_ds), SS_SELECTOR
2005-04-21 16:53:53 +02:00
! Call C startup code to set up a proper environment to run main().
push edx
push ebx
push SS_SELECTOR
push DS_SELECTOR
push CS_SELECTOR
call _cstart ! cstart(cs, ds, mds, parmoff, parmlen)
add esp, 5*4
! Reload gdtr, idtr and the segment registers to global descriptor table set
! up by prot_init().
lgdt (_gdt+GDT_SELECTOR)
lidt (_gdt+IDT_SELECTOR)
jmpf CS_SELECTOR:csinit
csinit:
o16 mov ax, DS_SELECTOR
mov ds, ax
mov es, ax
mov fs, ax
mov gs, ax
mov ss, ax
o16 mov ax, TSS_SELECTOR ! no other TSS is used
ltr ax
push 0 ! set flags to known good state
popf ! esp, clear nested task and int enable
jmp _main ! main()
!*===========================================================================*
!* interrupt handlers *
!* interrupt handlers for 386 32-bit protected mode *
!*===========================================================================*
!*===========================================================================*
!* hwint00 - 07 *
!*===========================================================================*
! Note this is a macro, it just looks like a subroutine.
#define hwint_master(irq) \
call save /* save interrupted process state */;\
2005-05-02 16:30:04 +02:00
push (_irq_handlers+4*irq) /* irq_handlers[irq] */;\
call _intr_handle /* intr_handle(irq_handlers[irq]) */;\
2005-04-21 16:53:53 +02:00
pop ecx ;\
cmp (_irq_actids+4*irq), 0 /* interrupt still active? */;\
jz 0f ;\
inb INT_CTLMASK /* get current mask */ ;\
orb al, [1<<irq] /* mask irq */ ;\
outb INT_CTLMASK /* disable the irq */;\
0: movb al, END_OF_INT ;\
outb INT_CTL /* reenable master 8259 */;\
ret /* restart (another) process */
2005-04-21 16:53:53 +02:00
! Each of these entry points is an expansion of the hwint_master macro
.align 16
_hwint00: ! Interrupt routine for irq 0 (the clock).
hwint_master(0)
.align 16
_hwint01: ! Interrupt routine for irq 1 (keyboard)
hwint_master(1)
.align 16
_hwint02: ! Interrupt routine for irq 2 (cascade!)
hwint_master(2)
.align 16
_hwint03: ! Interrupt routine for irq 3 (second serial)
hwint_master(3)
.align 16
_hwint04: ! Interrupt routine for irq 4 (first serial)
hwint_master(4)
.align 16
_hwint05: ! Interrupt routine for irq 5 (XT winchester)
hwint_master(5)
.align 16
_hwint06: ! Interrupt routine for irq 6 (floppy)
hwint_master(6)
.align 16
_hwint07: ! Interrupt routine for irq 7 (printer)
hwint_master(7)
!*===========================================================================*
!* hwint08 - 15 *
!*===========================================================================*
! Note this is a macro, it just looks like a subroutine.
#define hwint_slave(irq) \
call save /* save interrupted process state */;\
2005-05-02 16:30:04 +02:00
push (_irq_handlers+4*irq) /* irq_handlers[irq] */;\
2005-09-11 18:44:06 +02:00
call _intr_handle /* intr_handle(irq_handlers[irq]) */;\
2005-04-21 16:53:53 +02:00
pop ecx ;\
cmp (_irq_actids+4*irq), 0 /* interrupt still active? */;\
jz 0f ;\
2005-04-21 16:53:53 +02:00
inb INT2_CTLMASK ;\
orb al, [1<<[irq-8]] ;\
outb INT2_CTLMASK /* disable the irq */;\
0: movb al, END_OF_INT ;\
outb INT_CTL /* reenable master 8259 */;\
outb INT2_CTL /* reenable slave 8259 */;\
ret /* restart (another) process */
2005-04-21 16:53:53 +02:00
! Each of these entry points is an expansion of the hwint_slave macro
.align 16
_hwint08: ! Interrupt routine for irq 8 (realtime clock)
hwint_slave(8)
.align 16
_hwint09: ! Interrupt routine for irq 9 (irq 2 redirected)
hwint_slave(9)
.align 16
_hwint10: ! Interrupt routine for irq 10
hwint_slave(10)
.align 16
_hwint11: ! Interrupt routine for irq 11
hwint_slave(11)
.align 16
_hwint12: ! Interrupt routine for irq 12
hwint_slave(12)
.align 16
_hwint13: ! Interrupt routine for irq 13 (FPU exception)
hwint_slave(13)
.align 16
_hwint14: ! Interrupt routine for irq 14 (AT winchester)
hwint_slave(14)
.align 16
_hwint15: ! Interrupt routine for irq 15
hwint_slave(15)
!*===========================================================================*
!* save *
!*===========================================================================*
! Save for protected mode.
! This is much simpler than for 8086 mode, because the stack already points
! into the process table, or has already been switched to the kernel stack.
.align 16
save:
cld ! set direction flag to a known value
pushad ! save "general" registers
o16 push ds ! save ds
o16 push es ! save es
o16 push fs ! save fs
o16 push gs ! save gs
mov dx, ss ! ss is kernel data segment
mov ds, dx ! load rest of kernel segments
mov es, dx ! kernel does not use fs, gs
mov eax, esp ! prepare to return
incb (_k_reenter) ! from -1 if not reentering
jnz set_restart1 ! stack is already kernel stack
mov esp, k_stktop
push _restart ! build return address for int handler
xor ebp, ebp ! for stacktrace
jmp RETADR-P_STACKBASE(eax)
.align 4
set_restart1:
push restart1
jmp RETADR-P_STACKBASE(eax)
!*===========================================================================*
!* _s_call *
!*===========================================================================*
.align 16
_s_call:
_p_s_call:
cld ! set direction flag to a known value
Merge of David's ptrace branch. Summary: o Support for ptrace T_ATTACH/T_DETACH and T_SYSCALL o PM signal handling logic should now work properly, even with debuggers being present o Asynchronous PM/VFS protocol, full IPC support for senda(), and AMF_NOREPLY senda() flag DETAILS Process stop and delay call handling of PM: o Added sys_runctl() kernel call with sys_stop() and sys_resume() aliases, for PM to stop and resume a process o Added exception for sending/syscall-traced processes to sys_runctl(), and matching SIGKREADY pseudo-signal to PM o Fixed PM signal logic to deal with requests from a process after stopping it (so-called "delay calls"), using the SIGKREADY facility o Fixed various PM panics due to race conditions with delay calls versus VFS calls o Removed special PRIO_STOP priority value o Added SYS_LOCK RTS kernel flag, to stop an individual process from running while modifying its process structure Signal and debugger handling in PM: o Fixed debugger signals being dropped if a second signal arrives when the debugger has not retrieved the first one o Fixed debugger signals being sent to the debugger more than once o Fixed debugger signals unpausing process in VFS; removed PM_UNPAUSE_TR protocol message o Detached debugger signals from general signal logic and from being blocked on VFS calls, meaning that even VFS can now be traced o Fixed debugger being unable to receive more than one pending signal in one process stop o Fixed signal delivery being delayed needlessly when multiple signals are pending o Fixed wait test for tracer, which was returning for children that were not waited for o Removed second parallel pending call from PM to VFS for any process o Fixed process becoming runnable between exec() and debugger trap o Added support for notifying the debugger before the parent when a debugged child exits o Fixed debugger death causing child to remain stopped forever o Fixed consistently incorrect use of _NSIG Extensions to ptrace(): o Added T_ATTACH and T_DETACH ptrace request, to attach and detach a debugger to and from a process o Added T_SYSCALL ptrace request, to trace system calls o Added T_SETOPT ptrace request, to set trace options o Added TO_TRACEFORK trace option, to attach automatically to children of a traced process o Added TO_ALTEXEC trace option, to send SIGSTOP instead of SIGTRAP upon a successful exec() of the tracee o Extended T_GETUSER ptrace support to allow retrieving a process's priv structure o Removed T_STOP ptrace request again, as it does not help implementing debuggers properly o Added MINIX3-specific ptrace test (test42) o Added proper manual page for ptrace(2) Asynchronous PM/VFS interface: o Fixed asynchronous messages not being checked when receive() is called with an endpoint other than ANY o Added AMF_NOREPLY senda() flag, preventing such messages from satisfying the receive part of a sendrec() o Added asynsend3() that takes optional flags; asynsend() is now a #define passing in 0 as third parameter o Made PM/VFS protocol asynchronous; reintroduced tell_fs() o Made PM_BASE request/reply number range unique o Hacked in a horrible temporary workaround into RS to deal with newly revealed RS-PM-VFS race condition triangle until VFS is asynchronous System signal handling: o Fixed shutdown logic of device drivers; removed old SIGKSTOP signal o Removed is-superuser check from PM's do_procstat() (aka getsigset()) o Added sigset macros to allow system processes to deal with the full signal set, rather than just the POSIX subset Miscellaneous PM fixes: o Split do_getset into do_get and do_set, merging common code and making structure clearer o Fixed setpriority() being able to put to sleep processes using an invalid parameter, or revive zombie processes o Made find_proc() global; removed obsolete proc_from_pid() o Cleanup here and there Also included: o Fixed false-positive boot order kernel warning o Removed last traces of old NOTIFY_FROM code THINGS OF POSSIBLE INTEREST o It should now be possible to run PM at any priority, even lower than user processes o No assumptions are made about communication speed between PM and VFS, although communication must be FIFO o A debugger will now receive incoming debuggee signals at kill time only; the process may not yet be fully stopped o A first step has been made towards making the SYSTEM task preemptible
2009-09-30 11:57:22 +02:00
sub esp, 4 ! skip RETADR
pushad ! save "general" registers
2005-04-21 16:53:53 +02:00
o16 push ds
o16 push es
o16 push fs
o16 push gs
2006-03-10 17:10:05 +01:00
mov si, ss ! ss is kernel data segment
mov ds, si ! load rest of kernel segments
mov es, si ! kernel does not use fs, gs
incb (_k_reenter) ! increment kernel entry count
2005-04-21 16:53:53 +02:00
mov esi, esp ! assumes P_STACKBASE == 0
mov esp, k_stktop
xor ebp, ebp ! for stacktrace
! end of inline save
! now set up parameters for sys_call()
2006-03-10 17:10:05 +01:00
push edx ! event set or flags bit map
2005-04-21 16:53:53 +02:00
push ebx ! pointer to user message
2006-03-10 17:10:05 +01:00
push eax ! source / destination
push ecx ! call number (ipc primitive to use)
2006-03-10 17:10:05 +01:00
call _sys_call ! sys_call(call_nr, src_dst, m_ptr, bit_map)
2005-04-21 16:53:53 +02:00
! caller is now explicitly in proc_ptr
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
mov AXREG(esi), eax
2005-04-21 16:53:53 +02:00
! Fall into code to restart proc/task running.
!*===========================================================================*
!* restart *
!*===========================================================================*
_restart:
! Restart the current process or the next process if it is set.
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
cli
call _schedcheck ! ask C function who we're running
mov esp, (_proc_ptr) ! will assume P_STACKBASE == 0
lldt P_LDT_SEL(esp) ! enable process' segment descriptors
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
cmp P_CR3(esp), 0 ! process does not have its own PT
jz 0f
mov eax, P_CR3(esp)
cmp eax, (loadedcr3)
jz 0f
mov cr3, eax
mov (loadedcr3), eax
mov eax, (_proc_ptr)
mov (_ptproc), eax
mov (_dirtypde), 0
0:
2005-04-21 16:53:53 +02:00
lea eax, P_STACKTOP(esp) ! arrange for next interrupt
mov (_tss+TSS3_S_SP0), eax ! to save state in process table
restart1:
decb (_k_reenter)
o16 pop gs
o16 pop fs
o16 pop es
o16 pop ds
popad
add esp, 4 ! skip return adr
iretd ! continue process
!*===========================================================================*
!* exception handlers *
!*===========================================================================*
_divide_error:
push DIVIDE_VECTOR
jmp exception
_single_step_exception:
push DEBUG_VECTOR
jmp exception
_nmi:
push NMI_VECTOR
jmp exception
_breakpoint_exception:
push BREAKPOINT_VECTOR
jmp exception
_overflow:
push OVERFLOW_VECTOR
jmp exception
_bounds_check:
push BOUNDS_VECTOR
jmp exception
_inval_opcode:
push INVAL_OP_VECTOR
jmp exception
_copr_not_available:
push COPROC_NOT_VECTOR
jmp exception
_double_fault:
push DOUBLE_FAULT_VECTOR
jmp errexception
_copr_seg_overrun:
push COPROC_SEG_VECTOR
jmp exception
_inval_tss:
push INVAL_TSS_VECTOR
jmp errexception
_segment_not_present:
push SEG_NOT_VECTOR
jmp errexception
_stack_exception:
push STACK_FAULT_VECTOR
jmp errexception
_general_protection:
push PROTECTION_VECTOR
jmp errexception
_page_fault:
push PAGE_FAULT_VECTOR
push eax
mov eax, cr2
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
sseg mov (pagefaultcr2), eax
pop eax
2005-04-21 16:53:53 +02:00
jmp errexception
_copr_error:
push COPROC_ERR_VECTOR
jmp exception
!*===========================================================================*
!* exception *
!*===========================================================================*
! This is called for all exceptions which do not push an error code.
.align 16
exception:
sseg mov (trap_errno), 0 ! clear trap_errno
sseg pop (ex_number)
jmp exception1
!*===========================================================================*
!* errexception *
!*===========================================================================*
! This is called for all exceptions which push an error code.
.align 16
errexception:
sseg pop (ex_number)
sseg pop (trap_errno)
exception1: ! Common for all exceptions.
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
sseg mov (old_eax_ptr), esp ! where will eax be saved?
sseg sub (old_eax_ptr), PCREG-AXREG ! here
2005-04-21 16:53:53 +02:00
push eax ! eax is scratch register
2005-04-21 16:53:53 +02:00
mov eax, 0+4(esp) ! old eip
sseg mov (old_eip), eax
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
mov eax, esp
add eax, 4
sseg mov (old_eip_ptr), eax
2005-04-21 16:53:53 +02:00
movzx eax, 4+4(esp) ! old cs
sseg mov (old_cs), eax
mov eax, 8+4(esp) ! old eflags
sseg mov (old_eflags), eax
2005-04-21 16:53:53 +02:00
pop eax
call save
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
push (pagefaultcr2)
push (old_eax_ptr)
push (old_eip_ptr)
2005-04-21 16:53:53 +02:00
push (old_eflags)
push (old_cs)
push (old_eip)
push (trap_errno)
push (ex_number)
call _exception ! (ex_number, trap_errno, old_eip,
! old_cs, old_eflags)
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
add esp, 8*4
2005-04-21 16:53:53 +02:00
ret
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
2005-04-21 16:53:53 +02:00
!*===========================================================================*
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
!* write_cr3 *
2005-04-21 16:53:53 +02:00
!*===========================================================================*
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
! PUBLIC void write_cr3(unsigned long value);
_write_cr3:
push ebp
mov ebp, esp
mov eax, 8(ebp)
cmp eax, (loadedcr3)
jz 0f
mov cr3, eax
mov (loadedcr3), eax
mov (_dirtypde), 0
0:
pop ebp
ret
2005-04-21 16:53:53 +02:00
!*===========================================================================*
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
!* reload_cr3 *
!*===========================================================================*
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
! PUBLIC void reload_cr3(void);
_reload_cr3:
push ebp
mov ebp, esp
mov (_dirtypde), 0
mov eax, cr3
mov cr3, eax
pop ebp
ret
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
!*===========================================================================*
!* level0_call *
!*===========================================================================*
_level0_call:
call save
jmp (_level0_func)
2005-04-21 16:53:53 +02:00
!*===========================================================================*
!* data *
!*===========================================================================*
.sect .rom ! Before the string table please
.data2 0x526F ! this must be the first data entry (magic #)
.sect .bss
k_stack:
.space K_STACK_BYTES ! kernel stack
k_stktop: ! top of kernel stack
.comm ex_number, 4
.comm trap_errno, 4
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
.comm old_eip_ptr, 4
.comm old_eax_ptr, 4
2005-04-21 16:53:53 +02:00
.comm old_eip, 4
.comm old_cs, 4
.comm old_eflags, 4
Primary goal for these changes is: - no longer have kernel have its own page table that is loaded on every kernel entry (trap, interrupt, exception). the primary purpose is to reduce the number of required reloads. Result: - kernel can only access memory of process that was running when kernel was entered - kernel must be mapped into every process page table, so traps to kernel keep working Problem: - kernel must often access memory of arbitrary processes (e.g. send arbitrary processes messages); this can't happen directly any more; usually because that process' page table isn't loaded at all, sometimes because that memory isn't mapped in at all, sometimes because it isn't mapped in read-write. So: - kernel must be able to map in memory of any process, in its own address space. Implementation: - VM and kernel share a range of memory in which addresses of all page tables of all processes are available. This has two purposes: . Kernel has to know what data to copy in order to map in a range . Kernel has to know where to write the data in order to map it in That last point is because kernel has to write in the currently loaded page table. - Processes and kernel are separated through segments; kernel segments haven't changed. - The kernel keeps the process whose page table is currently loaded in 'ptproc.' - If it wants to map in a range of memory, it writes the value of the page directory entry for that range into the page directory entry in the currently loaded map. There is a slot reserved for such purposes. The kernel can then access this memory directly. - In order to do this, its segment has been increased (and the segments of processes start where it ends). - In the pagefault handler, detect if the kernel is doing 'trappable' memory access (i.e. a pagefault isn't a fatal error) and if so, - set the saved instruction pointer to phys_copy_fault, breaking out of phys_copy - set the saved eax register to the address of the page fault, both for sanity checking and for checking in which of the two ranges that phys_copy was called with the fault occured - Some boot-time processes do not have their own page table, and are mapped in with the kernel, and separated with segments. The kernel detects this using HASPT. If such a process has to be scheduled, any page table will work and no page table switch is done. Major changes in kernel are - When accessing user processes memory, kernel no longer explicitly checks before it does so if that memory is OK. It simply makes the mapping (if necessary), tries to do the operation, and traps the pagefault if that memory isn't present; if that happens, the copy function returns EFAULT. So all of the CHECKRANGE_OR_SUSPEND macros are gone. - Kernel no longer has to copy/read and parse page tables. - A message copying optimisation: when messages are copied, and the recipient isn't mapped in, they are copied into a buffer in the kernel. This is done in QueueMess. The next time the recipient is scheduled, this message is copied into its memory. This happens in schedcheck(). This eliminates the mapping/copying step for messages, and makes it easier to deliver messages. This eliminates soft_notify. - Kernel no longer creates a page table at all, so the vm_setbuf and pagetable writing in memory.c is gone. Minor changes in kernel are - ipc_stats thrown out, wasn't used - misc flags all renamed to MF_* - NOREC_* macros to enter and leave functions that should not be called recursively; just sanity checks really - code to fully decode segment selectors and descriptors to print on exceptions - lots of vmassert()s added, only executed if DEBUG_VMASSERT is 1
2009-09-21 16:31:52 +02:00
.comm pagefaultcr2, 4
.comm loadedcr3, 4