minix/sys/dev/ic/comreg.h

156 lines
6.5 KiB
C
Raw Normal View History

/* $NetBSD: comreg.h,v 1.17 2011/05/28 19:30:19 matt Exp $ */
/*-
* Copyright (c) 1991 The Regents of the University of California.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the University nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* @(#)comreg.h 7.2 (Berkeley) 5/9/91
*/
#include <dev/ic/ns16550reg.h>
#ifdef _KERNEL_OPT
#include "opt_com.h"
#endif
#define COM_FREQ 1843200 /* 16-bit baud rate divisor */
#ifndef COM_TOLERANCE
#define COM_TOLERANCE 30 /* baud rate tolerance, in 0.1% units */
#endif
/* interrupt enable register */
#define IER_ERXRDY 0x1 /* Enable receiver interrupt */
#define IER_ETXRDY 0x2 /* Enable transmitter empty interrupt */
#define IER_ERLS 0x4 /* Enable line status interrupt */
#define IER_EMSC 0x8 /* Enable modem status interrupt */
#define IER_ERTS 0x40 /* Enable RTS interrupt */
#define IER_ECTS 0x80 /* Enable CTS interrupt */
/* PXA2X0's ns16550 ports have extra bits in this register */
#define IER_ERXTOUT 0x10 /* Enable rx timeout interrupt */
#define IER_EUART 0x40 /* Enable UART */
/* interrupt identification register */
#define IIR_IMASK 0xf
#define IIR_RXTOUT 0xc
#define IIR_RLS 0x6 /* Line status change */
#define IIR_RXRDY 0x4 /* Receiver ready */
#define IIR_TXRDY 0x2 /* Transmitter ready */
#define IIR_MLSC 0x0 /* Modem status */
#define IIR_NOPEND 0x1 /* No pending interrupts */
#define IIR_FIFO_MASK 0xc0 /* set if FIFOs are enabled */
/* fifo control register */
#define FIFO_ENABLE 0x01 /* Turn the FIFO on */
#define FIFO_RCV_RST 0x02 /* Reset RX FIFO */
#define FIFO_XMT_RST 0x04 /* Reset TX FIFO */
#define FIFO_DMA_MODE 0x08
#define FIFO_TRIGGER_1 0x00 /* Trigger RXRDY intr on 1 character */
#define FIFO_TRIGGER_4 0x40 /* ibid 4 */
#define FIFO_TRIGGER_8 0x80 /* ibid 8 */
#define FIFO_TRIGGER_14 0xc0 /* ibid 14 */
/* enhanced feature register */
#define EFR_AUTOCTS 0x80 /* Automatic CTS flow control */
#define EFR_AUTORTS 0x40 /* Automatic RTS flow control */
#define EFR_SPECIAL 0x20 /* Special char detect */
#define EFR_EFCR 0x10 /* Enhanced function control bit */
#define EFR_TXFLOWBOTH 0x0c /* Automatic transmit XON/XOFF 1 and 2 */
#define EFR_TXFLOW1 0x08 /* Automatic transmit XON/XOFF 1 */
#define EFR_TXFLOW2 0x04 /* Automatic transmit XON/XOFF 2 */
#define EFR_TXFLOWNONE 0x00 /* No automatic XON/XOFF transmit */
#define EFR_RXFLOWBOTH 0x03 /* Automatic receive XON/XOFF 1 and 2 */
#define EFR_RXFLOW1 0x02 /* Automatic receive XON/XOFF 1 */
#define EFR_RXFLOW2 0x01 /* Automatic receive XON/XOFF 2 */
#define EFR_RXFLOWNONE 0x00 /* No automatic XON/XOFF receive */
/* line control register */
#define LCR_EERS 0xBF /* Enable access to Enhanced Register Set */
#define LCR_DLAB 0x80 /* Divisor latch access enable */
#define LCR_SBREAK 0x40 /* Break Control */
#define LCR_PZERO 0x38 /* Space parity */
#define LCR_PONE 0x28 /* Mark parity */
#define LCR_PEVEN 0x18 /* Even parity */
#define LCR_PODD 0x08 /* Odd parity */
#define LCR_PNONE 0x00 /* No parity */
#define LCR_PENAB 0x08 /* XXX - low order bit of all parity */
#define LCR_STOPB 0x04 /* 2 stop bits per serial word */
#define LCR_8BITS 0x03 /* 8 bits per serial word */
#define LCR_7BITS 0x02 /* 7 bits */
#define LCR_6BITS 0x01 /* 6 bits */
#define LCR_5BITS 0x00 /* 5 bits */
/* modem control register */
#define MCR_PRESCALE 0x80 /* 16650/16950: Baud rate prescaler select */
#define MCR_TCR_TLR 0x40 /* OMAP: enables access to the TCR & TLR regs */
#define MCR_XONENABLE 0x20 /* OMAP XON_EN */
#define MCR_LOOPBACK 0x10 /* Loop test: echos from TX to RX */
#define MCR_IENABLE 0x08 /* Out2: enables UART interrupts */
#define MCR_DRS 0x04 /* Out1: resets some internal modems */
#define MCR_RTS 0x02 /* Request To Send */
#define MCR_DTR 0x01 /* Data Terminal Ready */
/* line status register */
#define LSR_RCV_FIFO 0x80
#define LSR_TSRE 0x40 /* Transmitter empty: byte sent */
#define LSR_TXRDY 0x20 /* Transmitter buffer empty */
#define LSR_BI 0x10 /* Break detected */
#define LSR_FE 0x08 /* Framing error: bad stop bit */
#define LSR_PE 0x04 /* Parity error */
#define LSR_OE 0x02 /* Overrun, lost incoming byte */
#define LSR_RXRDY 0x01 /* Byte ready in Receive Buffer */
#define LSR_RCV_MASK 0x1f /* Mask for incoming data or error */
/* modem status register */
/* All deltas are from the last read of the MSR. */
#define MSR_DCD 0x80 /* Current Data Carrier Detect */
#define MSR_RI 0x40 /* Current Ring Indicator */
#define MSR_DSR 0x20 /* Current Data Set Ready */
#define MSR_CTS 0x10 /* Current Clear to Send */
#define MSR_DDCD 0x08 /* DCD has changed state */
#define MSR_TERI 0x04 /* RI has toggled low to high */
#define MSR_DDSR 0x02 /* DSR has changed state */
#define MSR_DCTS 0x01 /* CTS has changed state */
/* OMAP mode definition register 1 */
#define MDR1_FRAME_END_MODE 0x80
#define MDR1_SIP_MODE 0x40
#define MDR1_SCT 0x20
#define MDR1_SET_TXIR 0x10
#define MDR1_IR_SLEEP 0x08
#define MDR1_MODE_DISABLE 0x07
#define MDR1_MODE_FIR 0x05
#define MDR1_MODE_MIR 0x04
#define MDR1_MODE_UART_13X 0x03
#define MDR1_MODE_UART_16X_AUTOBAUD 0x02
#define MDR1_MODE_SIR 0x01
#define MDR1_MODE_UART_16X 0x00
#define MDR1_MODE_MASK 0x07
/* XXX ISA-specific. */
#define COM_NPORTS 8