minix/drivers/e1000/e1000.c

1202 lines
35 KiB
C
Raw Normal View History

/**
* @file e1000.c
*
* @brief This file contains a device driver for Intel Pro/1000
* Gigabit Ethernet Controllers.
*/
#include <minix/drivers.h>
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
#include <minix/netdriver.h>
#include <stdlib.h>
#include <net/gen/ether.h>
#include <net/gen/eth_io.h>
#include <machine/pci.h>
#include <minix/ds.h>
#include <minix/vm.h>
#include <timers.h>
#include <sys/mman.h>
#include "assert.h"
#include "e1000.h"
#include "e1000_hw.h"
#include "e1000_reg.h"
#include "e1000_pci.h"
PRIVATE u16_t pcitab_e1000[] =
{
E1000_DEV_ID_82540EM,
E1000_DEV_ID_82541GI_LF,
E1000_DEV_ID_ICH10_R_BM_LF,
0,
};
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
PRIVATE int e1000_instance;
PRIVATE e1000_t e1000_state;
_PROTOTYPE( PRIVATE void e1000_init, (message *mp) );
_PROTOTYPE( PRIVATE void e1000_init_pci, (void) );
_PROTOTYPE( PRIVATE int e1000_probe, (e1000_t *e, int skip) );
_PROTOTYPE( PRIVATE int e1000_init_hw, (e1000_t *e) );
_PROTOTYPE( PRIVATE void e1000_init_addr, (e1000_t *e) );
_PROTOTYPE( PRIVATE void e1000_init_buf, (e1000_t *e) );
_PROTOTYPE( PRIVATE void e1000_reset_hw, (e1000_t *e) );
_PROTOTYPE( PRIVATE void e1000_writev_s, (message *mp, int from_int) );
_PROTOTYPE( PRIVATE void e1000_readv_s, (message *mp, int from_int) );
_PROTOTYPE( PRIVATE void e1000_getstat_s, (message *mp) );
_PROTOTYPE( PRIVATE void e1000_interrupt, (message *mp) );
_PROTOTYPE( PRIVATE int e1000_link_changed, (e1000_t *e) );
_PROTOTYPE( PRIVATE void e1000_stop, (void) );
_PROTOTYPE( PRIVATE uint32_t e1000_reg_read, (e1000_t *e, uint32_t reg) );
_PROTOTYPE( PRIVATE void e1000_reg_write, (e1000_t *e, uint32_t reg,
uint32_t value) );
_PROTOTYPE( PRIVATE void e1000_reg_set, (e1000_t *e, uint32_t reg,
uint32_t value) );
_PROTOTYPE( PRIVATE void e1000_reg_unset, (e1000_t *e, uint32_t reg,
uint32_t value) );
_PROTOTYPE( PRIVATE u16_t eeprom_eerd, (void *e, int reg) );
_PROTOTYPE( PRIVATE u16_t eeprom_ich, (void *e, int reg) );
_PROTOTYPE( PRIVATE int eeprom_ich_init, (e1000_t *e) );
_PROTOTYPE( PRIVATE int eeprom_ich_cycle, (const e1000_t *e, u32_t timeout) );
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
_PROTOTYPE( PRIVATE void reply, (e1000_t *e) );
_PROTOTYPE( PRIVATE void mess_reply, (message *req, message *reply) );
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
/* SEF functions and variables. */
FORWARD _PROTOTYPE( void sef_local_startup, (void) );
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
FORWARD _PROTOTYPE( int sef_cb_init_fresh, (int type, sef_init_info_t *info) );
New RS and new signal handling for system processes. UPDATING INFO: 20100317: /usr/src/etc/system.conf updated to ignore default kernel calls: copy it (or merge it) to /etc/system.conf. The hello driver (/dev/hello) added to the distribution: # cd /usr/src/commands/scripts && make clean install # cd /dev && MAKEDEV hello KERNEL CHANGES: - Generic signal handling support. The kernel no longer assumes PM as a signal manager for every process. The signal manager of a given process can now be specified in its privilege slot. When a signal has to be delivered, the kernel performs the lookup and forwards the signal to the appropriate signal manager. PM is the default signal manager for user processes, RS is the default signal manager for system processes. To enable ptrace()ing for system processes, it is sufficient to change the default signal manager to PM. This will temporarily disable crash recovery, though. - sys_exit() is now split into sys_exit() (i.e. exit() for system processes, which generates a self-termination signal), and sys_clear() (i.e. used by PM to ask the kernel to clear a process slot when a process exits). - Added a new kernel call (i.e. sys_update()) to swap two process slots and implement live update. PM CHANGES: - Posix signal handling is no longer allowed for system processes. System signals are split into two fixed categories: termination and non-termination signals. When a non-termination signaled is processed, PM transforms the signal into an IPC message and delivers the message to the system process. When a termination signal is processed, PM terminates the process. - PM no longer assumes itself as the signal manager for system processes. It now makes sure that every system signal goes through the kernel before being actually processes. The kernel will then dispatch the signal to the appropriate signal manager which may or may not be PM. SYSLIB CHANGES: - Simplified SEF init and LU callbacks. - Added additional predefined SEF callbacks to debug crash recovery and live update. - Fixed a temporary ack in the SEF init protocol. SEF init reply is now completely synchronous. - Added SEF signal event type to provide a uniform interface for system processes to deal with signals. A sef_cb_signal_handler() callback is available for system processes to handle every received signal. A sef_cb_signal_manager() callback is used by signal managers to process system signals on behalf of the kernel. - Fixed a few bugs with memory mapping and DS. VM CHANGES: - Page faults and memory requests coming from the kernel are now implemented using signals. - Added a new VM call to swap two process slots and implement live update. - The call is used by RS at update time and in turn invokes the kernel call sys_update(). RS CHANGES: - RS has been reworked with a better functional decomposition. - Better kernel call masks. com.h now defines the set of very basic kernel calls every system service is allowed to use. This makes system.conf simpler and easier to maintain. In addition, this guarantees a higher level of isolation for system libraries that use one or more kernel calls internally (e.g. printf). - RS is the default signal manager for system processes. By default, RS intercepts every signal delivered to every system process. This makes crash recovery possible before bringing PM and friends in the loop. - RS now supports fast rollback when something goes wrong while initializing the new version during a live update. - Live update is now implemented by keeping the two versions side-by-side and swapping the process slots when the old version is ready to update. - Crash recovery is now implemented by keeping the two versions side-by-side and cleaning up the old version only when the recovery process is complete. DS CHANGES: - Fixed a bug when the process doing ds_publish() or ds_delete() is not known by DS. - Fixed the completely broken support for strings. String publishing is now implemented in the system library and simply wraps publishing of memory ranges. Ideally, we should adopt a similar approach for other data types as well. - Test suite fixed. DRIVER CHANGES: - The hello driver has been added to the Minix distribution to demonstrate basic live update and crash recovery functionalities. - Other drivers have been adapted to conform the new SEF interface.
2010-03-17 02:15:29 +01:00
FORWARD _PROTOTYPE( void sef_cb_signal_handler, (int signo) );
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
EXTERN int env_argc;
EXTERN char **env_argv;
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
/*===========================================================================*
* main *
*===========================================================================*/
int main(int argc, char *argv[])
{
message m;
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
int ipc_status;
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
int r;
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
/* SEF local startup. */
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
env_setargs(argc, argv);
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
sef_local_startup();
/*
* Enter the main driver loop.
*/
while (TRUE)
{
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
if ((r= netdriver_receive(ANY, &m, &ipc_status)) != OK)
{
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
panic("netdriver_receive failed: %d", r);
}
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
if (is_ipc_notify(ipc_status))
{
switch (_ENDPOINT_P(m.m_source))
{
case HARDWARE:
e1000_interrupt(&m);
break;
New RS and new signal handling for system processes. UPDATING INFO: 20100317: /usr/src/etc/system.conf updated to ignore default kernel calls: copy it (or merge it) to /etc/system.conf. The hello driver (/dev/hello) added to the distribution: # cd /usr/src/commands/scripts && make clean install # cd /dev && MAKEDEV hello KERNEL CHANGES: - Generic signal handling support. The kernel no longer assumes PM as a signal manager for every process. The signal manager of a given process can now be specified in its privilege slot. When a signal has to be delivered, the kernel performs the lookup and forwards the signal to the appropriate signal manager. PM is the default signal manager for user processes, RS is the default signal manager for system processes. To enable ptrace()ing for system processes, it is sufficient to change the default signal manager to PM. This will temporarily disable crash recovery, though. - sys_exit() is now split into sys_exit() (i.e. exit() for system processes, which generates a self-termination signal), and sys_clear() (i.e. used by PM to ask the kernel to clear a process slot when a process exits). - Added a new kernel call (i.e. sys_update()) to swap two process slots and implement live update. PM CHANGES: - Posix signal handling is no longer allowed for system processes. System signals are split into two fixed categories: termination and non-termination signals. When a non-termination signaled is processed, PM transforms the signal into an IPC message and delivers the message to the system process. When a termination signal is processed, PM terminates the process. - PM no longer assumes itself as the signal manager for system processes. It now makes sure that every system signal goes through the kernel before being actually processes. The kernel will then dispatch the signal to the appropriate signal manager which may or may not be PM. SYSLIB CHANGES: - Simplified SEF init and LU callbacks. - Added additional predefined SEF callbacks to debug crash recovery and live update. - Fixed a temporary ack in the SEF init protocol. SEF init reply is now completely synchronous. - Added SEF signal event type to provide a uniform interface for system processes to deal with signals. A sef_cb_signal_handler() callback is available for system processes to handle every received signal. A sef_cb_signal_manager() callback is used by signal managers to process system signals on behalf of the kernel. - Fixed a few bugs with memory mapping and DS. VM CHANGES: - Page faults and memory requests coming from the kernel are now implemented using signals. - Added a new VM call to swap two process slots and implement live update. - The call is used by RS at update time and in turn invokes the kernel call sys_update(). RS CHANGES: - RS has been reworked with a better functional decomposition. - Better kernel call masks. com.h now defines the set of very basic kernel calls every system service is allowed to use. This makes system.conf simpler and easier to maintain. In addition, this guarantees a higher level of isolation for system libraries that use one or more kernel calls internally (e.g. printf). - RS is the default signal manager for system processes. By default, RS intercepts every signal delivered to every system process. This makes crash recovery possible before bringing PM and friends in the loop. - RS now supports fast rollback when something goes wrong while initializing the new version during a live update. - Live update is now implemented by keeping the two versions side-by-side and swapping the process slots when the old version is ready to update. - Crash recovery is now implemented by keeping the two versions side-by-side and cleaning up the old version only when the recovery process is complete. DS CHANGES: - Fixed a bug when the process doing ds_publish() or ds_delete() is not known by DS. - Fixed the completely broken support for strings. String publishing is now implemented in the system library and simply wraps publishing of memory ranges. Ideally, we should adopt a similar approach for other data types as well. - Test suite fixed. DRIVER CHANGES: - The hello driver has been added to the Minix distribution to demonstrate basic live update and crash recovery functionalities. - Other drivers have been adapted to conform the new SEF interface.
2010-03-17 02:15:29 +01:00
case CLOCK:
break;
}
continue;
}
switch (m.m_type)
{
case DL_WRITEV_S: e1000_writev_s(&m, FALSE); break;
case DL_READV_S: e1000_readv_s(&m, FALSE); break;
case DL_CONF: e1000_init(&m); break;
case DL_GETSTAT_S: e1000_getstat_s(&m); break;
default:
panic("illegal message: %d", m.m_type);
}
}
}
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
/*===========================================================================*
* sef_local_startup *
*===========================================================================*/
PRIVATE void sef_local_startup()
{
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
/* Register init callbacks. */
sef_setcb_init_fresh(sef_cb_init_fresh);
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
sef_setcb_init_lu(sef_cb_init_fresh);
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
sef_setcb_init_restart(sef_cb_init_fresh);
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
/* Register live update callbacks. */
sef_setcb_lu_prepare(sef_cb_lu_prepare_always_ready);
sef_setcb_lu_state_isvalid(sef_cb_lu_state_isvalid_workfree);
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
New RS and new signal handling for system processes. UPDATING INFO: 20100317: /usr/src/etc/system.conf updated to ignore default kernel calls: copy it (or merge it) to /etc/system.conf. The hello driver (/dev/hello) added to the distribution: # cd /usr/src/commands/scripts && make clean install # cd /dev && MAKEDEV hello KERNEL CHANGES: - Generic signal handling support. The kernel no longer assumes PM as a signal manager for every process. The signal manager of a given process can now be specified in its privilege slot. When a signal has to be delivered, the kernel performs the lookup and forwards the signal to the appropriate signal manager. PM is the default signal manager for user processes, RS is the default signal manager for system processes. To enable ptrace()ing for system processes, it is sufficient to change the default signal manager to PM. This will temporarily disable crash recovery, though. - sys_exit() is now split into sys_exit() (i.e. exit() for system processes, which generates a self-termination signal), and sys_clear() (i.e. used by PM to ask the kernel to clear a process slot when a process exits). - Added a new kernel call (i.e. sys_update()) to swap two process slots and implement live update. PM CHANGES: - Posix signal handling is no longer allowed for system processes. System signals are split into two fixed categories: termination and non-termination signals. When a non-termination signaled is processed, PM transforms the signal into an IPC message and delivers the message to the system process. When a termination signal is processed, PM terminates the process. - PM no longer assumes itself as the signal manager for system processes. It now makes sure that every system signal goes through the kernel before being actually processes. The kernel will then dispatch the signal to the appropriate signal manager which may or may not be PM. SYSLIB CHANGES: - Simplified SEF init and LU callbacks. - Added additional predefined SEF callbacks to debug crash recovery and live update. - Fixed a temporary ack in the SEF init protocol. SEF init reply is now completely synchronous. - Added SEF signal event type to provide a uniform interface for system processes to deal with signals. A sef_cb_signal_handler() callback is available for system processes to handle every received signal. A sef_cb_signal_manager() callback is used by signal managers to process system signals on behalf of the kernel. - Fixed a few bugs with memory mapping and DS. VM CHANGES: - Page faults and memory requests coming from the kernel are now implemented using signals. - Added a new VM call to swap two process slots and implement live update. - The call is used by RS at update time and in turn invokes the kernel call sys_update(). RS CHANGES: - RS has been reworked with a better functional decomposition. - Better kernel call masks. com.h now defines the set of very basic kernel calls every system service is allowed to use. This makes system.conf simpler and easier to maintain. In addition, this guarantees a higher level of isolation for system libraries that use one or more kernel calls internally (e.g. printf). - RS is the default signal manager for system processes. By default, RS intercepts every signal delivered to every system process. This makes crash recovery possible before bringing PM and friends in the loop. - RS now supports fast rollback when something goes wrong while initializing the new version during a live update. - Live update is now implemented by keeping the two versions side-by-side and swapping the process slots when the old version is ready to update. - Crash recovery is now implemented by keeping the two versions side-by-side and cleaning up the old version only when the recovery process is complete. DS CHANGES: - Fixed a bug when the process doing ds_publish() or ds_delete() is not known by DS. - Fixed the completely broken support for strings. String publishing is now implemented in the system library and simply wraps publishing of memory ranges. Ideally, we should adopt a similar approach for other data types as well. - Test suite fixed. DRIVER CHANGES: - The hello driver has been added to the Minix distribution to demonstrate basic live update and crash recovery functionalities. - Other drivers have been adapted to conform the new SEF interface.
2010-03-17 02:15:29 +01:00
/* Register signal callbacks. */
sef_setcb_signal_handler(sef_cb_signal_handler);
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
/* Let SEF perform startup. */
sef_startup();
}
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
/*===========================================================================*
* sef_cb_init_fresh *
*===========================================================================*/
PRIVATE int sef_cb_init_fresh(int UNUSED(type), sef_init_info_t *UNUSED(info))
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
{
/* Initialize the e1000 driver. */
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
long v;
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
int r;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
v = 0;
(void) env_parse("instance", "d", 0, &v, 0, 255);
e1000_instance = (int) v;
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
/* Clear state. */
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
memset(&e1000_state, 0, sizeof(e1000_state));
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
/* Perform calibration. */
if((r = tsc_calibrate()) != OK)
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
{
panic("tsc_calibrate failed: %d", r);
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
}
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
/* Announce we are up! */
netdriver_announce();
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
return(OK);
}
New RS and new signal handling for system processes. UPDATING INFO: 20100317: /usr/src/etc/system.conf updated to ignore default kernel calls: copy it (or merge it) to /etc/system.conf. The hello driver (/dev/hello) added to the distribution: # cd /usr/src/commands/scripts && make clean install # cd /dev && MAKEDEV hello KERNEL CHANGES: - Generic signal handling support. The kernel no longer assumes PM as a signal manager for every process. The signal manager of a given process can now be specified in its privilege slot. When a signal has to be delivered, the kernel performs the lookup and forwards the signal to the appropriate signal manager. PM is the default signal manager for user processes, RS is the default signal manager for system processes. To enable ptrace()ing for system processes, it is sufficient to change the default signal manager to PM. This will temporarily disable crash recovery, though. - sys_exit() is now split into sys_exit() (i.e. exit() for system processes, which generates a self-termination signal), and sys_clear() (i.e. used by PM to ask the kernel to clear a process slot when a process exits). - Added a new kernel call (i.e. sys_update()) to swap two process slots and implement live update. PM CHANGES: - Posix signal handling is no longer allowed for system processes. System signals are split into two fixed categories: termination and non-termination signals. When a non-termination signaled is processed, PM transforms the signal into an IPC message and delivers the message to the system process. When a termination signal is processed, PM terminates the process. - PM no longer assumes itself as the signal manager for system processes. It now makes sure that every system signal goes through the kernel before being actually processes. The kernel will then dispatch the signal to the appropriate signal manager which may or may not be PM. SYSLIB CHANGES: - Simplified SEF init and LU callbacks. - Added additional predefined SEF callbacks to debug crash recovery and live update. - Fixed a temporary ack in the SEF init protocol. SEF init reply is now completely synchronous. - Added SEF signal event type to provide a uniform interface for system processes to deal with signals. A sef_cb_signal_handler() callback is available for system processes to handle every received signal. A sef_cb_signal_manager() callback is used by signal managers to process system signals on behalf of the kernel. - Fixed a few bugs with memory mapping and DS. VM CHANGES: - Page faults and memory requests coming from the kernel are now implemented using signals. - Added a new VM call to swap two process slots and implement live update. - The call is used by RS at update time and in turn invokes the kernel call sys_update(). RS CHANGES: - RS has been reworked with a better functional decomposition. - Better kernel call masks. com.h now defines the set of very basic kernel calls every system service is allowed to use. This makes system.conf simpler and easier to maintain. In addition, this guarantees a higher level of isolation for system libraries that use one or more kernel calls internally (e.g. printf). - RS is the default signal manager for system processes. By default, RS intercepts every signal delivered to every system process. This makes crash recovery possible before bringing PM and friends in the loop. - RS now supports fast rollback when something goes wrong while initializing the new version during a live update. - Live update is now implemented by keeping the two versions side-by-side and swapping the process slots when the old version is ready to update. - Crash recovery is now implemented by keeping the two versions side-by-side and cleaning up the old version only when the recovery process is complete. DS CHANGES: - Fixed a bug when the process doing ds_publish() or ds_delete() is not known by DS. - Fixed the completely broken support for strings. String publishing is now implemented in the system library and simply wraps publishing of memory ranges. Ideally, we should adopt a similar approach for other data types as well. - Test suite fixed. DRIVER CHANGES: - The hello driver has been added to the Minix distribution to demonstrate basic live update and crash recovery functionalities. - Other drivers have been adapted to conform the new SEF interface.
2010-03-17 02:15:29 +01:00
/*===========================================================================*
* sef_cb_signal_handler *
*===========================================================================*/
PRIVATE void sef_cb_signal_handler(int signo)
{
E1000_DEBUG(3, ("e1000: got signal\n"));
/* Only check for termination signal, ignore anything else. */
if (signo != SIGTERM) return;
e1000_stop();
}
/*===========================================================================*
* e1000_init *
*===========================================================================*/
PRIVATE void e1000_init(message *mp)
{
static int first_time = 1;
message reply_mess;
e1000_t *e;
E1000_DEBUG(3, ("e1000: init()\n"));
/* Configure PCI devices, if needed. */
if (first_time)
{
first_time = 0;
e1000_init_pci();
}
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
e = &e1000_state;
/* Initialize hardware, if needed. */
if (!(e->status & E1000_ENABLED) && !(e1000_init_hw(e)))
{
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
reply_mess.m_type = DL_CONF_REPLY;
reply_mess.DL_STAT = ENXIO;
mess_reply(mp, &reply_mess);
return;
}
/* Reply back to INET. */
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
reply_mess.m_type = DL_CONF_REPLY;
reply_mess.DL_STAT = OK;
*(ether_addr_t *) reply_mess.DL_HWADDR = e->address;
mess_reply(mp, &reply_mess);
}
/*===========================================================================*
* e1000_int_pci *
*===========================================================================*/
PRIVATE void e1000_init_pci()
{
e1000_t *e;
/* Initialize the PCI bus. */
pci_init();
/* Try to detect e1000's. */
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
e = &e1000_state;
strcpy(e->name, "e1000#0");
e->name[6] += e1000_instance;
e1000_probe(e, e1000_instance);
}
/*===========================================================================*
* e1000_probe *
*===========================================================================*/
PRIVATE int e1000_probe(e1000_t *e, int skip)
{
int i, r, devind;
u16_t vid, did;
u32_t status[2];
u32_t gfpreg, sector_base_addr;
char *dname;
E1000_DEBUG(3, ("%s: probe()\n", e->name));
/*
* Attempt to iterate the PCI bus. Start at the beginning.
*/
if ((r = pci_first_dev(&devind, &vid, &did)) == 0)
{
return FALSE;
}
/* Loop devices on the PCI bus. */
for(;;)
{
for (i = 0; pcitab_e1000[i] != 0; i++)
{
if (vid != 0x8086)
continue;
if (did != pcitab_e1000[i])
continue;
else
break;
}
if (pcitab_e1000[i] != 0)
{
if (!skip)
break;
skip--;
}
if (!(r = pci_next_dev(&devind, &vid, &did)))
{
return FALSE;
}
}
/*
* Successfully detected an Intel Pro/1000 on the PCI bus.
*/
e->status |= E1000_DETECTED;
e->eeprom_read = eeprom_eerd;
/*
* Set card specific properties.
*/
switch (did)
{
case E1000_DEV_ID_ICH10_R_BM_LF:
e->eeprom_read = eeprom_ich;
break;
case E1000_DEV_ID_82541GI_LF:
e->eeprom_done_bit = (1 << 1);
e->eeprom_addr_off = 2;
break;
default:
e->eeprom_done_bit = (1 << 4);
e->eeprom_addr_off = 8;
break;
}
/* Inform the user about the new card. */
if (!(dname = pci_dev_name(vid, did)))
{
dname = "Intel Pro/1000 Gigabit Ethernet Card";
}
E1000_DEBUG(1, ("%s: %s (%04x/%04x/%02x) at %s\n",
e->name, dname, vid, did, e->revision,
pci_slot_name(devind)));
/* Reserve PCI resources found. */
if ((r = pci_reserve_ok(devind)) != OK)
{
panic("failed to reserve PCI device: %d", r);
}
/* Read PCI configuration. */
e->irq = pci_attr_r8(devind, PCI_ILR);
e->regs = vm_map_phys(SELF, (void *) pci_attr_r32(devind, PCI_BAR),
0x20000);
/* Verify mapped registers. */
if (e->regs == (u8_t *) -1) {
panic("failed to map hardware registers from PCI");
}
/* Optionally map flash memory. */
if (pci_attr_r32(devind, PCI_BAR_3))
{
if((e->flash = vm_map_phys(SELF,
(void *) pci_attr_r32(devind, PCI_BAR_2), 0x10000)) == MAP_FAILED) {
if((e->flash = vm_map_phys(SELF,
(void *) pci_attr_r32(devind, PCI_BAR_2), 0x1000))
== MAP_FAILED) {
panic("e1000: couldn't map in flash.");
}
}
gfpreg = E1000_READ_FLASH_REG(e, ICH_FLASH_GFPREG);
/*
* sector_base_addr is a "sector"-aligned address (4096 bytes)
*/
sector_base_addr = gfpreg & FLASH_GFPREG_BASE_MASK;
/* flash_base_addr is byte-aligned */
e->flash_base_addr = sector_base_addr << FLASH_SECTOR_ADDR_SHIFT;
}
/*
* Output debug information.
*/
status[0] = e1000_reg_read(e, E1000_REG_STATUS);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
E1000_DEBUG(3, ("%s: MEM at %p, IRQ %d\n",
e->name, e->regs, e->irq));
E1000_DEBUG(3, ("%s: link %s, %s duplex\n",
e->name, status[0] & 3 ? "up" : "down",
status[0] & 1 ? "full" : "half"));
return TRUE;
}
/*===========================================================================*
* e1000_init_hw *
*===========================================================================*/
PRIVATE int e1000_init_hw(e)
e1000_t *e;
{
int r, i;
e->status |= E1000_ENABLED;
e->irq_hook = e->irq;
/*
* Set the interrupt handler and policy. Do not automatically
* re-enable interrupts. Return the IRQ line number on interrupts.
*/
if ((r = sys_irqsetpolicy(e->irq, 0, &e->irq_hook)) != OK)
{
panic("sys_irqsetpolicy failed: %d", r);
}
if ((r = sys_irqenable(&e->irq_hook)) != OK)
{
panic("sys_irqenable failed: %d", r);
}
/* Reset hardware. */
e1000_reset_hw(e);
/*
* Initialize appropriately, according to section 14.3 General Configuration
* of Intel's Gigabit Ethernet Controllers Software Developer's Manual.
*/
e1000_reg_set(e, E1000_REG_CTRL, E1000_REG_CTRL_ASDE | E1000_REG_CTRL_SLU);
e1000_reg_unset(e, E1000_REG_CTRL, E1000_REG_CTRL_LRST);
e1000_reg_unset(e, E1000_REG_CTRL, E1000_REG_CTRL_PHY_RST);
e1000_reg_unset(e, E1000_REG_CTRL, E1000_REG_CTRL_ILOS);
e1000_reg_write(e, E1000_REG_FCAL, 0);
e1000_reg_write(e, E1000_REG_FCAH, 0);
e1000_reg_write(e, E1000_REG_FCT, 0);
e1000_reg_write(e, E1000_REG_FCTTV, 0);
e1000_reg_unset(e, E1000_REG_CTRL, E1000_REG_CTRL_VME);
/* Clear Multicast Table Array (MTA). */
for (i = 0; i < 128; i++)
{
e1000_reg_write(e, E1000_REG_MTA + i, 0);
}
/* Initialize statistics registers. */
for (i = 0; i < 64; i++)
{
e1000_reg_write(e, E1000_REG_CRCERRS + (i * 4), 0);
}
/*
* Aquire MAC address and setup RX/TX buffers.
*/
e1000_init_addr(e);
e1000_init_buf(e);
/* Enable interrupts. */
e1000_reg_set(e, E1000_REG_IMS, E1000_REG_IMS_LSC |
E1000_REG_IMS_RXO |
E1000_REG_IMS_RXT |
E1000_REG_IMS_TXQE |
E1000_REG_IMS_TXDW);
return TRUE;
}
/*===========================================================================*
* e1000_init_addr *
*===========================================================================*/
PRIVATE void e1000_init_addr(e)
e1000_t *e;
{
static char eakey[]= E1000_ENVVAR "#_EA";
static char eafmt[]= "x:x:x:x:x:x";
u16_t word;
int i;
long v;
/*
* Do we have a user defined ethernet address?
*/
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
eakey[sizeof(E1000_ENVVAR)-1] = '0' + e1000_instance;
for (i= 0; i < 6; i++)
{
if (env_parse(eakey, eafmt, i, &v, 0x00L, 0xFFL) != EP_SET)
break;
else
e->address.ea_addr[i]= v;
}
/*
* If that fails, read Ethernet Address from EEPROM.
*/
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
if (i != 6)
{
for (i = 0; i < 3; i++)
{
word = e->eeprom_read(e, i);
e->address.ea_addr[(i * 2)] = (word & 0xff);
e->address.ea_addr[(i * 2) + 1] = (word & 0xff00) >> 8;
}
}
/*
* Set Receive Address.
*/
e1000_reg_write(e, E1000_REG_RAL, *(u32_t *)(&e->address.ea_addr[0]));
e1000_reg_write(e, E1000_REG_RAH, *(u16_t *)(&e->address.ea_addr[4]));
e1000_reg_set(e, E1000_REG_RAH, E1000_REG_RAH_AV);
e1000_reg_set(e, E1000_REG_RCTL, E1000_REG_RCTL_MPE);
E1000_DEBUG(3, ("%s: Ethernet Address %x:%x:%x:%x:%x:%x\n", e->name,
e->address.ea_addr[0], e->address.ea_addr[1],
e->address.ea_addr[2], e->address.ea_addr[3],
e->address.ea_addr[4], e->address.ea_addr[5]));
}
/*===========================================================================*
* e1000_init_buf *
*===========================================================================*/
PRIVATE void e1000_init_buf(e)
e1000_t *e;
{
phys_bytes rx_desc_p, rx_buff_p;
phys_bytes tx_desc_p, tx_buff_p;
int i;
/* Number of descriptors. */
e->rx_desc_count = E1000_RXDESC_NR;
e->tx_desc_count = E1000_TXDESC_NR;
/*
* First, allocate the receive descriptors.
*/
if (!e->rx_desc)
{
if ((e->rx_desc = alloc_contig(sizeof(e1000_rx_desc_t) *
e->rx_desc_count, AC_ALIGN4K,
&rx_desc_p)) == NULL) {
panic("failed to allocate RX descriptors");
}
memset(e->rx_desc, 0, sizeof(e1000_rx_desc_t) * e->rx_desc_count);
/*
* Allocate 2048-byte buffers.
*/
e->rx_buffer_size = E1000_RXDESC_NR * E1000_IOBUF_SIZE;
/* Attempt to allocate. */
if ((e->rx_buffer = alloc_contig(e->rx_buffer_size,
AC_ALIGN4K, &rx_buff_p)) == NULL)
{
panic("failed to allocate RX buffers");
}
/* Setup receive descriptors. */
for (i = 0; i < E1000_RXDESC_NR; i++)
{
e->rx_desc[i].buffer = rx_buff_p + (i * E1000_IOBUF_SIZE);
}
}
/*
* Then, allocate transmit descriptors.
*/
if (!e->tx_desc)
{
if ((e->tx_desc = alloc_contig(sizeof(e1000_tx_desc_t) *
e->tx_desc_count, AC_ALIGN4K,
&tx_desc_p)) == NULL) {
panic("failed to allocate TX descriptors");
}
memset(e->tx_desc, 0, sizeof(e1000_tx_desc_t) * e->tx_desc_count);
/*
* Allocate 2048-byte buffers.
*/
e->tx_buffer_size = E1000_TXDESC_NR * E1000_IOBUF_SIZE;
/* Attempt to allocate. */
if ((e->tx_buffer = alloc_contig(e->tx_buffer_size,
AC_ALIGN4K, &tx_buff_p)) == NULL)
{
panic("failed to allocate TX buffers");
}
/* Setup transmit descriptors. */
for (i = 0; i < E1000_RXDESC_NR; i++)
{
e->tx_desc[i].buffer = tx_buff_p + (i * E1000_IOBUF_SIZE);
}
}
/*
* Setup the receive ring registers.
*/
e1000_reg_write(e, E1000_REG_RDBAL, rx_desc_p);
e1000_reg_write(e, E1000_REG_RDBAH, 0);
e1000_reg_write(e, E1000_REG_RDLEN, e->rx_desc_count *
sizeof(e1000_rx_desc_t));
e1000_reg_write(e, E1000_REG_RDH, 0);
e1000_reg_write(e, E1000_REG_RDT, e->rx_desc_count - 1);
e1000_reg_unset(e, E1000_REG_RCTL, E1000_REG_RCTL_BSIZE);
e1000_reg_set(e, E1000_REG_RCTL, E1000_REG_RCTL_EN);
/*
* Setup the transmit ring registers.
*/
e1000_reg_write(e, E1000_REG_TDBAL, tx_desc_p);
e1000_reg_write(e, E1000_REG_TDBAH, 0);
e1000_reg_write(e, E1000_REG_TDLEN, e->tx_desc_count *
sizeof(e1000_tx_desc_t));
e1000_reg_write(e, E1000_REG_TDH, 0);
e1000_reg_write(e, E1000_REG_TDT, 0);
e1000_reg_set( e, E1000_REG_TCTL, E1000_REG_TCTL_EN | E1000_REG_TCTL_PSP);
}
/*===========================================================================*
* e1000_reset_hw *
*===========================================================================*/
PRIVATE void e1000_reset_hw(e)
e1000_t *e;
{
/* Assert a Device Reset signal. */
e1000_reg_set(e, E1000_REG_CTRL, E1000_REG_CTRL_RST);
/* Wait one microsecond. */
tickdelay(1);
}
/*===========================================================================*
* e1000_writev_s *
*===========================================================================*/
PRIVATE void e1000_writev_s(mp, from_int)
message *mp;
int from_int;
{
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
e1000_t *e = &e1000_state;
e1000_tx_desc_t *desc;
iovec_s_t iovec[E1000_IOVEC_NR];
int r, head, tail, i, bytes = 0, size;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
E1000_DEBUG(3, ("e1000: writev_s(%p,%d)\n", mp, from_int));
/* Are we called from the interrupt handler? */
if (!from_int)
{
/* We cannot write twice simultaneously.
assert(!(e->status & E1000_WRITING)); */
/* Copy write message. */
e->tx_message = *mp;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
e->client = mp->m_source;
e->status |= E1000_WRITING;
/* Must be a sane vector count. */
assert(e->tx_message.DL_COUNT > 0);
assert(e->tx_message.DL_COUNT < E1000_IOVEC_NR);
/*
* Copy the I/O vector table.
*/
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
if ((r = sys_safecopyfrom(e->tx_message.DL_ENDPT,
e->tx_message.DL_GRANT, 0,
(vir_bytes) iovec, e->tx_message.DL_COUNT *
sizeof(iovec_s_t), D)) != OK)
{
panic("sys_safecopyfrom() failed: %d", r);
}
/* Find the head, tail and current descriptors. */
head = e1000_reg_read(e, E1000_REG_TDH);
tail = e1000_reg_read(e, E1000_REG_TDT);
desc = &e->tx_desc[tail];
E1000_DEBUG(4, ("%s: head=%d, tail=%d\n",
e->name, head, tail));
/* Loop vector elements. */
for (i = 0; i < e->tx_message.DL_COUNT; i++)
{
size = iovec[i].iov_size < (E1000_IOBUF_SIZE - bytes) ?
iovec[i].iov_size : (E1000_IOBUF_SIZE - bytes);
E1000_DEBUG(4, ("iovec[%d] = %d\n", i, size));
/* Copy bytes to TX queue buffers. */
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
if ((r = sys_safecopyfrom(e->tx_message.DL_ENDPT,
iovec[i].iov_grant, 0,
(vir_bytes) e->tx_buffer +
(tail * E1000_IOBUF_SIZE),
size, D)) != OK)
{
panic("sys_safecopyfrom() failed: %d", r);
}
/* Mark this descriptor ready. */
desc->status = 0;
desc->command = 0;
desc->length = size;
/* Marks End-of-Packet. */
if (i == e->tx_message.DL_COUNT - 1)
{
desc->command = E1000_TX_CMD_EOP |
E1000_TX_CMD_FCS |
E1000_TX_CMD_RS;
}
/* Move to next descriptor. */
tail = (tail + 1) % e->tx_desc_count;
bytes += size;
desc = &e->tx_desc[tail];
}
/* Increment tail. Start transmission. */
e1000_reg_write(e, E1000_REG_TDT, tail);
E1000_DEBUG(2, ("e1000: wrote %d byte packet\n", bytes));
}
else
{
e->status |= E1000_TRANSMIT;
}
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
reply(e);
}
/*===========================================================================*
* e1000_readv_s *
*===========================================================================*/
PRIVATE void e1000_readv_s(mp, from_int)
message *mp;
int from_int;
{
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
e1000_t *e = &e1000_state;
e1000_rx_desc_t *desc;
iovec_s_t iovec[E1000_IOVEC_NR];
int i, r, head, tail, cur, bytes = 0, size;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
E1000_DEBUG(3, ("e1000: readv_s(%p,%d)\n", mp, from_int));
/* Are we called from the interrupt handler? */
if (!from_int)
{
e->rx_message = *mp;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
e->client = mp->m_source;
e->status |= E1000_READING;
e->rx_size = 0;
assert(e->rx_message.DL_COUNT > 0);
assert(e->rx_message.DL_COUNT < E1000_IOVEC_NR);
}
if (e->status & E1000_READING)
{
/*
* Copy the I/O vector table first.
*/
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
if ((r = sys_safecopyfrom(e->rx_message.DL_ENDPT,
e->rx_message.DL_GRANT, 0,
(vir_bytes) iovec, e->rx_message.DL_COUNT *
sizeof(iovec_s_t), D)) != OK)
{
panic("sys_safecopyfrom() failed: %d", r);
}
/* Find the head, tail and current descriptors. */
head = e1000_reg_read(e, E1000_REG_RDH);
tail = e1000_reg_read(e, E1000_REG_RDT);
cur = (tail + 1) % e->rx_desc_count;
desc = &e->rx_desc[cur];
/*
* Only handle one packet at a time.
*/
if (!(desc->status & E1000_RX_STATUS_EOP))
{
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
reply(e);
return;
}
E1000_DEBUG(4, ("%s: head=%x, tail=%d\n",
e->name, head, tail));
/*
* Copy to vector elements.
*/
for (i = 0; i < e->rx_message.DL_COUNT && bytes < desc->length; i++)
{
size = iovec[i].iov_size < (desc->length - bytes) ?
iovec[i].iov_size : (desc->length - bytes);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
E1000_DEBUG(4, ("iovec[%d] = %lu[%d]\n",
i, iovec[i].iov_size, size));
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
if ((r = sys_safecopyto(e->rx_message.DL_ENDPT, iovec[i].iov_grant,
0, (vir_bytes) e->rx_buffer + bytes +
(cur * E1000_IOBUF_SIZE),
size, D)) != OK)
{
panic("sys_safecopyto() failed: %d", r);
}
bytes += size;
}
desc->status = 0;
/*
* Update state.
*/
e->rx_size = bytes;
e->status |= E1000_RECEIVED;
E1000_DEBUG(2, ("e1000: got %d byte packet\n", e->rx_size));
/* Increment tail. */
e1000_reg_write(e, E1000_REG_RDT, (tail + 1) % e->rx_desc_count);
}
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
reply(e);
}
/*===========================================================================*
* e1000_getstat_s *
*===========================================================================*/
PRIVATE void e1000_getstat_s(mp)
message *mp;
{
int r;
eth_stat_t stats;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
e1000_t *e = &e1000_state;
E1000_DEBUG(3, ("e1000: getstat_s()\n"));
stats.ets_recvErr = e1000_reg_read(e, E1000_REG_RXERRC);
stats.ets_sendErr = 0;
stats.ets_OVW = 0;
stats.ets_CRCerr = e1000_reg_read(e, E1000_REG_CRCERRS);
stats.ets_frameAll = 0;
stats.ets_missedP = e1000_reg_read(e, E1000_REG_MPC);
stats.ets_packetR = e1000_reg_read(e, E1000_REG_TPR);
stats.ets_packetT = e1000_reg_read(e, E1000_REG_TPT);
stats.ets_collision = e1000_reg_read(e, E1000_REG_COLC);
stats.ets_transAb = 0;
stats.ets_carrSense = 0;
stats.ets_fifoUnder = 0;
stats.ets_fifoOver = 0;
stats.ets_CDheartbeat = 0;
stats.ets_OWC = 0;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
sys_safecopyto(mp->DL_ENDPT, mp->DL_GRANT, 0, (vir_bytes)&stats,
sizeof(stats), D);
mp->m_type = DL_STAT_REPLY;
if((r=send(mp->m_source, mp)) != OK)
panic("e1000_getstat: send() failed: %d", r);
}
/*===========================================================================*
* e1000_interrupt *
*===========================================================================*/
PRIVATE void e1000_interrupt(mp)
message *mp;
{
e1000_t *e;
u32_t cause;
E1000_DEBUG(3, ("e1000: interrupt\n"));
/*
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
* Check the card for interrupt reason(s).
*/
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
e = &e1000_state;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
/* Re-enable interrupts. */
if (sys_irqenable(&e->irq_hook) != OK)
{
panic("failed to re-enable IRQ");
}
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
/* Read the Interrupt Cause Read register. */
if ((cause = e1000_reg_read(e, E1000_REG_ICR)))
{
if (cause & E1000_REG_ICR_LSC)
e1000_link_changed(e);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
if (cause & (E1000_REG_ICR_RXO | E1000_REG_ICR_RXT))
e1000_readv_s(&e->rx_message, TRUE);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
if ((cause & E1000_REG_ICR_TXQE) ||
(cause & E1000_REG_ICR_TXDW))
e1000_writev_s(&e->tx_message, TRUE);
}
}
/*===========================================================================*
* e1000_link_changed *
*===========================================================================*/
PRIVATE int e1000_link_changed(e)
e1000_t *e;
{
E1000_DEBUG(4, ("%s: link_changed()\n", e->name));
return FALSE;
}
/*===========================================================================*
* e1000_stop *
*===========================================================================*/
PRIVATE void e1000_stop()
{
E1000_DEBUG(3, ("e1000: stop()\n"));
exit(EXIT_SUCCESS);
}
/*===========================================================================*
* e1000_reg_read *
*===========================================================================*/
PRIVATE uint32_t e1000_reg_read(e, reg)
e1000_t *e;
uint32_t reg;
{
uint32_t value;
/* Assume a sane register. */
assert(reg < 0x1ffff);
/* Read from memory mapped register. */
value = *(u32_t *)(e->regs + reg);
/* Return the result. */
return value;
}
/*===========================================================================*
* e1000_reg_write *
*===========================================================================*/
PRIVATE void e1000_reg_write(e, reg, value)
e1000_t *e;
uint32_t reg;
uint32_t value;
{
/* Assume a sane register. */
assert(reg < 0x1ffff);
/* Write to memory mapped register. */
*(u32_t *)(e->regs + reg) = value;
}
/*===========================================================================*
* e1000_reg_set *
*===========================================================================*/
PRIVATE void e1000_reg_set(e, reg, value)
e1000_t *e;
uint32_t reg;
uint32_t value;
{
uint32_t data;
/* First read the current value. */
data = e1000_reg_read(e, reg);
/* Set value, and write back. */
e1000_reg_write(e, reg, data | value);
}
/*===========================================================================*
* e1000_reg_unset *
*===========================================================================*/
PRIVATE void e1000_reg_unset(e, reg, value)
e1000_t *e;
uint32_t reg;
uint32_t value;
{
uint32_t data;
/* First read the current value. */
data = e1000_reg_read(e, reg);
/* Unset value, and write back. */
e1000_reg_write(e, reg, data & ~value);
}
/*===========================================================================*
* eeprom_eerd *
*===========================================================================*/
PRIVATE u16_t eeprom_eerd(v, reg)
void *v;
int reg;
{
e1000_t *e = (e1000_t *) v;
u16_t data;
/* Request EEPROM read. */
e1000_reg_write(e, E1000_REG_EERD,
(reg << e->eeprom_addr_off) | (E1000_REG_EERD_START));
/* Wait until ready. */
while (!(e1000_reg_read(e, E1000_REG_EERD) &
e->eeprom_done_bit));
/* Fetch data. */
data = (e1000_reg_read(e, E1000_REG_EERD) &
E1000_REG_EERD_DATA) >> 16;
return data;
}
/*===========================================================================*
* eeprom_ich_init *
*===========================================================================*/
PRIVATE int eeprom_ich_init(e)
e1000_t *e;
{
union ich8_hws_flash_status hsfsts;
int ret_val = -1;
int i = 0;
hsfsts.regval = E1000_READ_FLASH_REG16(e, ICH_FLASH_HSFSTS);
/* Check if the flash descriptor is valid */
if (hsfsts.hsf_status.fldesvalid == 0)
{
E1000_DEBUG(3, ("Flash descriptor invalid. "
"SW Sequencing must be used."));
goto out;
}
/* Clear FCERR and DAEL in hw status by writing 1 */
hsfsts.hsf_status.flcerr = 1;
hsfsts.hsf_status.dael = 1;
E1000_WRITE_FLASH_REG16(e, ICH_FLASH_HSFSTS, hsfsts.regval);
/*
* Either we should have a hardware SPI cycle in progress
* bit to check against, in order to start a new cycle or
* FDONE bit should be changed in the hardware so that it
* is 1 after hardware reset, which can then be used as an
* indication whether a cycle is in progress or has been
* completed.
*/
if (hsfsts.hsf_status.flcinprog == 0)
{
/*
* There is no cycle running at present,
* so we can start a cycle.
* Begin by setting Flash Cycle Done.
*/
hsfsts.hsf_status.flcdone = 1;
E1000_WRITE_FLASH_REG16(e, ICH_FLASH_HSFSTS, hsfsts.regval);
ret_val = 0;
}
else
{
/*
* Otherwise poll for sometime so the current
* cycle has a chance to end before giving up.
*/
for (i = 0; i < ICH_FLASH_READ_COMMAND_TIMEOUT; i++)
{
hsfsts.regval = E1000_READ_FLASH_REG16(e, ICH_FLASH_HSFSTS);
if (hsfsts.hsf_status.flcinprog == 0)
{
ret_val = 0;
break;
}
tickdelay(1);
}
if (ret_val == 0)
{
/*
* Successful in waiting for previous cycle to timeout,
* now set the Flash Cycle Done.
*/
hsfsts.hsf_status.flcdone = 1;
E1000_WRITE_FLASH_REG16(e, ICH_FLASH_HSFSTS,
hsfsts.regval);
}
else
{
E1000_DEBUG(3, ("Flash controller busy, cannot get access"));
}
}
out:
return ret_val;
}
/*===========================================================================*
* eeprom_ich_cycle *
*===========================================================================*/
PRIVATE int eeprom_ich_cycle(const e1000_t *e, u32_t timeout)
{
union ich8_hws_flash_ctrl hsflctl;
union ich8_hws_flash_status hsfsts;
int ret_val = -1;
u32_t i = 0;
E1000_DEBUG(3, ("e1000_flash_cycle_ich8lan"));
/* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */
hsflctl.regval = E1000_READ_FLASH_REG16(e, ICH_FLASH_HSFCTL);
hsflctl.hsf_ctrl.flcgo = 1;
E1000_WRITE_FLASH_REG16(e, ICH_FLASH_HSFCTL, hsflctl.regval);
/* wait till FDONE bit is set to 1 */
do
{
hsfsts.regval = E1000_READ_FLASH_REG16(e, ICH_FLASH_HSFSTS);
if (hsfsts.hsf_status.flcdone == 1)
break;
tickdelay(1);
}
while (i++ < timeout);
if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0)
ret_val = 0;
return ret_val;
}
/*===========================================================================*
* eeprom_ich *
*===========================================================================*/
PRIVATE u16_t eeprom_ich(v, reg)
void *v;
int reg;
{
union ich8_hws_flash_status hsfsts;
union ich8_hws_flash_ctrl hsflctl;
u32_t flash_linear_addr;
u32_t flash_data = 0;
int ret_val = -1;
u8_t count = 0;
e1000_t *e = (e1000_t *) v;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
u16_t data = 0;
E1000_DEBUG(3, ("e1000_read_flash_data_ich8lan"));
if (reg > ICH_FLASH_LINEAR_ADDR_MASK)
goto out;
reg *= sizeof(u16_t);
flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & reg) +
e->flash_base_addr;
do {
tickdelay(1);
/* Steps */
ret_val = eeprom_ich_init(e);
if (ret_val != 0)
break;
hsflctl.regval = E1000_READ_FLASH_REG16(e, ICH_FLASH_HSFCTL);
/* 0b/1b corresponds to 1 or 2 byte size, respectively. */
hsflctl.hsf_ctrl.fldbcount = 1;
hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ;
E1000_WRITE_FLASH_REG16(e, ICH_FLASH_HSFCTL, hsflctl.regval);
E1000_WRITE_FLASH_REG(e, ICH_FLASH_FADDR, flash_linear_addr);
ret_val = eeprom_ich_cycle(v, ICH_FLASH_READ_COMMAND_TIMEOUT);
/*
* Check if FCERR is set to 1, if set to 1, clear it
* and try the whole sequence a few more times, else
* read in (shift in) the Flash Data0, the order is
* least significant byte first msb to lsb
*/
if (ret_val == 0)
{
flash_data = E1000_READ_FLASH_REG(e, ICH_FLASH_FDATA0);
data = (u16_t)(flash_data & 0x0000FFFF);
break;
}
else
{
/*
* If we've gotten here, then things are probably
* completely hosed, but if the error condition is
* detected, it won't hurt to give it another try...
* ICH_FLASH_CYCLE_REPEAT_COUNT times.
*/
hsfsts.regval = E1000_READ_FLASH_REG16(e, ICH_FLASH_HSFSTS);
if (hsfsts.hsf_status.flcerr == 1)
{
/* Repeat for some time before giving up. */
continue;
}
else if (hsfsts.hsf_status.flcdone == 0)
{
E1000_DEBUG(3, ("Timeout error - flash cycle "
"did not complete."));
break;
}
}
} while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
out:
return data;
}
/*===========================================================================*
* reply *
*===========================================================================*/
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
PRIVATE void reply(e)
e1000_t *e;
{
message msg;
int r;
/* Only reply to client for read/write request. */
if (!(e->status & E1000_READING ||
e->status & E1000_WRITING))
{
return;
}
/* Construct reply message. */
msg.m_type = DL_TASK_REPLY;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
msg.DL_FLAGS = DL_NOFLAGS;
msg.DL_COUNT = 0;
/* Did we successfully receive packet(s)? */
if (e->status & E1000_READING &&
e->status & E1000_RECEIVED)
{
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
msg.DL_FLAGS |= DL_PACK_RECV;
msg.DL_COUNT = e->rx_size >= ETH_MIN_PACK_SIZE ?
e->rx_size : ETH_MIN_PACK_SIZE;
/* Clear flags. */
e->status &= ~(E1000_READING | E1000_RECEIVED);
}
/* Did we successfully transmit packet(s)? */
if (e->status & E1000_TRANSMIT &&
e->status & E1000_WRITING)
{
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
msg.DL_FLAGS |= DL_PACK_SEND;
/* Clear flags. */
e->status &= ~(E1000_WRITING | E1000_TRANSMIT);
}
/* Acknowledge to INET. */
if ((r = send(e->client, &msg)) != OK)
{
panic("send() failed: %d", r);
}
}
/*===========================================================================*
* mess_reply *
*===========================================================================*/
PRIVATE void mess_reply(req, reply_mess)
message *req;
message *reply_mess;
{
if (send(req->m_source, reply_mess) != OK)
{
panic("unable to send reply message");
}
}