minix/drivers/at_wini/at_wini.c

/* This file contains the device dependent part of a driver for the IBM-AT
 * winchester controller.  Written by Adri Koppes.
 *
 * The file contains one entry point:
 *
 *   at_winchester_task:	main entry when system is brought up
 *
 * Changes:
 *   Aug 19, 2005   ATA PCI support, supports SATA  (Ben Gras)
 *   Nov 18, 2004   moved AT disk driver to user-space  (Jorrit N. Herder)
 *   Aug 20, 2004   watchdogs replaced by sync alarms  (Jorrit N. Herder)
 *   Mar 23, 2000   added ATAPI CDROM support  (Michael Temari)
 *   May 14, 2000   d-d/i rewrite  (Kees J. Bot)
 *   Apr 13, 1992   device dependent/independent split  (Kees J. Bot)
 */

#include "at_wini.h"

#include <minix/sysutil.h>
#include <minix/keymap.h>
#include <sys/ioc_disk.h>
#include <ibm/pci.h>

#define ATAPI_DEBUG	    0	/* To debug ATAPI code. */

/* I/O Ports used by winchester disk controllers. */

/* Read and write registers */
#define REG_CMD_BASE0	0x1F0	/* command base register of controller 0 */
#define REG_CMD_BASE1	0x170	/* command base register of controller 1 */
#define REG_CTL_BASE0	0x3F6	/* control base register of controller 0 */
#define REG_CTL_BASE1	0x376	/* control base register of controller 1 */

#define PCI_CTL_OFF	    2	/* Offset of control registers from BAR2 */
#define PCI_DMA_2ND_OFF	    8	/* Offset of DMA registers from BAR4 for 
				 * secondary channel
				 */

#define REG_DATA	    0	/* data register (offset from the base reg.) */
#define REG_PRECOMP	    1	/* start of write precompensation */
#define REG_COUNT	    2	/* sectors to transfer */
#define REG_SECTOR	    3	/* sector number */
#define REG_CYL_LO	    4	/* low byte of cylinder number */
#define REG_CYL_HI	    5	/* high byte of cylinder number */
#define REG_LDH		    6	/* lba, drive and head */
#define   LDH_DEFAULT		0xA0	/* ECC enable, 512 bytes per sector */
#define   LDH_LBA		0x40	/* Use LBA addressing */
#define	  LDH_DEV		0x10	/* Drive 1 iff set */
#define   ldh_init(drive)	(LDH_DEFAULT | ((drive) << 4))

/* Read only registers */
#define REG_STATUS	    7	/* status */
#define   STATUS_BSY		0x80	/* controller busy */
#define	  STATUS_RDY		0x40	/* drive ready */
#define	  STATUS_WF		0x20	/* write fault */
#define	  STATUS_SC		0x10	/* seek complete (obsolete) */
#define	  STATUS_DRQ		0x08	/* data transfer request */
#define	  STATUS_CRD		0x04	/* corrected data */
#define	  STATUS_IDX		0x02	/* index pulse */
#define	  STATUS_ERR		0x01	/* error */
#define	  STATUS_ADMBSY	       0x100	/* administratively busy (software) */
#define REG_ERROR	    1	/* error code */
#define	  ERROR_BB		0x80	/* bad block */
#define	  ERROR_ECC		0x40	/* bad ecc bytes */
#define	  ERROR_ID		0x10	/* id not found */
#define	  ERROR_AC		0x04	/* aborted command */
#define	  ERROR_TK		0x02	/* track zero error */
#define	  ERROR_DM		0x01	/* no data address mark */

/* Write only registers */
#define REG_COMMAND	    7	/* command */
#define   CMD_IDLE		0x00	/* for w_command: drive idle */
#define   CMD_RECALIBRATE	0x10	/* recalibrate drive */
#define   CMD_READ		0x20	/* read data */
#define   CMD_READ_EXT		0x24	/* read data (LBA48 addressed) */
#define   CMD_READ_DMA_EXT	0x25	/* read data using DMA (w/ LBA48) */
#define   CMD_WRITE		0x30	/* write data */
#define	  CMD_WRITE_EXT		0x34	/* write data (LBA48 addressed) */
#define   CMD_WRITE_DMA_EXT	0x35	/* write data using DMA (w/ LBA48) */
#define   CMD_READVERIFY	0x40	/* read verify */
#define   CMD_FORMAT		0x50	/* format track */
#define   CMD_SEEK		0x70	/* seek cylinder */
#define   CMD_DIAG		0x90	/* execute device diagnostics */
#define   CMD_SPECIFY		0x91	/* specify parameters */
#define   CMD_READ_DMA		0xC8	/* read data using DMA */
#define   CMD_WRITE_DMA		0xCA	/* write data using DMA */
#define   ATA_IDENTIFY		0xEC	/* identify drive */
/* #define REG_CTL		0x206	*/ /* control register */
#define REG_CTL		0	/* control register */
#define   CTL_NORETRY		0x80	/* disable access retry */
#define   CTL_NOECC		0x40	/* disable ecc retry */
#define   CTL_EIGHTHEADS	0x08	/* more than eight heads */
#define   CTL_RESET		0x04	/* reset controller */
#define   CTL_INTDISABLE	0x02	/* disable interrupts */
#define REG_CTL_ALTSTAT 0	/* alternate status register */

/* Identify words */
#define ID_GENERAL		0x00	/* General configuration information */
#define		ID_GEN_NOT_ATA		0x8000	/* Not an ATA device */
#define ID_CAPABILITIES		0x31	/* Capabilities (49)*/
#define		ID_CAP_LBA		0x0200	/* LBA supported */
#define		ID_CAP_DMA		0x0100	/* DMA supported */
#define ID_FIELD_VALIDITY	0x35	/* Field Validity (53) */
#define		ID_FV_88		0x04	/* Word 88 is valid (UDMA) */
#define ID_MULTIWORD_DMA	0x3f	/* Multiword DMA (63) */
#define		ID_MWDMA_2_SEL		0x0400	/* Mode 2 is selected */
#define		ID_MWDMA_1_SEL		0x0200	/* Mode 1 is selected */
#define		ID_MWDMA_0_SEL		0x0100	/* Mode 0 is selected */
#define		ID_MWDMA_2_SUP		0x0004	/* Mode 2 is supported */
#define		ID_MWDMA_1_SUP		0x0002	/* Mode 1 is supported */
#define		ID_MWDMA_0_SUP		0x0001	/* Mode 0 is supported */
#define ID_CSS			0x53	/* Command Sets Supported (83) */
#define		ID_CSS_LBA48		0x0400
#define ID_ULTRA_DMA		0x58	/* Ultra DMA (88) */
#define		ID_UDMA_5_SEL		0x2000	/* Mode 5 is selected */
#define		ID_UDMA_4_SEL		0x1000	/* Mode 4 is selected */
#define		ID_UDMA_3_SEL		0x0800	/* Mode 3 is selected */
#define		ID_UDMA_2_SEL		0x0400	/* Mode 2 is selected */
#define		ID_UDMA_1_SEL		0x0200	/* Mode 1 is selected */
#define		ID_UDMA_0_SEL		0x0100	/* Mode 0 is selected */
#define		ID_UDMA_5_SUP		0x0020	/* Mode 5 is supported */
#define		ID_UDMA_4_SUP		0x0010	/* Mode 4 is supported */
#define		ID_UDMA_3_SUP		0x0008	/* Mode 3 is supported */
#define		ID_UDMA_2_SUP		0x0004	/* Mode 2 is supported */
#define		ID_UDMA_1_SUP		0x0002	/* Mode 1 is supported */
#define		ID_UDMA_0_SUP		0x0001	/* Mode 0 is supported */

/* DMA registers */
#define DMA_COMMAND		0		/* Command register */
#define		DMA_CMD_WRITE		0x08	/* PCI bus master writes */
#define		DMA_CMD_START		0x01	/* Start Bus Master */
#define DMA_STATUS		2		/* Status register */
#define		DMA_ST_D1_DMACAP	0x40	/* Drive 1 is DMA capable */
#define		DMA_ST_D0_DMACAP	0x20	/* Drive 0 is DMA capable */
#define		DMA_ST_INT		0x04	/* Interrupt */
#define		DMA_ST_ERROR		0x02	/* Error */
#define		DMA_ST_BM_ACTIVE	0x01	/* Bus Master IDE Active */
#define DMA_PRDTP		4		/* PRD Table Pointer */

/* Check for the presence of LBA48 only on drives that are 'big'. */
#define LBA48_CHECK_SIZE	0x0f000000
#define LBA_MAX_SIZE		0x0fffffff	/* Highest sector size for
						 * regular LBA.
						 */

#if ENABLE_ATAPI
#define   ERROR_SENSE           0xF0    /* sense key mask */
#define     SENSE_NONE          0x00    /* no sense key */
#define     SENSE_RECERR        0x10    /* recovered error */
#define     SENSE_NOTRDY        0x20    /* not ready */
#define     SENSE_MEDERR        0x30    /* medium error */
#define     SENSE_HRDERR        0x40    /* hardware error */
#define     SENSE_ILRQST        0x50    /* illegal request */
#define     SENSE_UATTN         0x60    /* unit attention */
#define     SENSE_DPROT         0x70    /* data protect */
#define     SENSE_ABRT          0xb0    /* aborted command */
#define     SENSE_MISCOM        0xe0    /* miscompare */
#define   ERROR_MCR             0x08    /* media change requested */
#define   ERROR_ABRT            0x04    /* aborted command */
#define   ERROR_EOM             0x02    /* end of media detected */
#define   ERROR_ILI             0x01    /* illegal length indication */
#define REG_FEAT            1   /* features */
#define   FEAT_OVERLAP          0x02    /* overlap */
#define   FEAT_DMA              0x01    /* dma */
#define REG_IRR             2   /* interrupt reason register */
#define   IRR_REL               0x04    /* release */
#define   IRR_IO                0x02    /* direction for xfer */
#define   IRR_COD               0x01    /* command or data */
#define REG_SAMTAG          3
#define REG_CNT_LO          4   /* low byte of cylinder number */
#define REG_CNT_HI          5   /* high byte of cylinder number */
#define REG_DRIVE           6   /* drive select */
#endif

#define REG_STATUS          7   /* status */
#define   STATUS_BSY            0x80    /* controller busy */
#define   STATUS_DRDY           0x40    /* drive ready */
#define   STATUS_DMADF          0x20    /* dma ready/drive fault */
#define   STATUS_SRVCDSC        0x10    /* service or dsc */
#define   STATUS_DRQ            0x08    /* data transfer request */
#define   STATUS_CORR           0x04    /* correctable error occurred */
#define   STATUS_CHECK          0x01    /* check error */

#ifdef ENABLE_ATAPI
#define   ATAPI_PACKETCMD       0xA0    /* packet command */
#define   ATAPI_IDENTIFY        0xA1    /* identify drive */
#define   SCSI_READ10           0x28    /* read from disk */
#define   SCSI_SENSE            0x03    /* sense request */

#define CD_SECTOR_SIZE		2048	/* sector size of a CD-ROM */
#endif /* ATAPI */

/* Interrupt request lines. */
#define NO_IRQ		 0	/* no IRQ set yet */

#define ATAPI_PACKETSIZE	12
#define SENSE_PACKETSIZE	18

/* Common command block */
struct command {
  u8_t	precomp;	/* REG_PRECOMP, etc. */
  u8_t	count;
  u8_t	sector;
  u8_t	cyl_lo;
  u8_t	cyl_hi;
  u8_t	ldh;
  u8_t	command;

  /* The following at for LBA48 */
  u8_t	count_prev;
  u8_t	sector_prev;
  u8_t	cyl_lo_prev;
  u8_t	cyl_hi_prev;
};

/* Error codes */
#define ERR		 (-1)	/* general error */
#define ERR_BAD_SECTOR	 (-2)	/* block marked bad detected */

/* Some controllers don't interrupt, the clock will wake us up. */
#define WAKEUP_SECS	32			/* drive may be out for 31 seconds max */
#define WAKEUP_TICKS	(WAKEUP_SECS*HZ)

/* Miscellaneous. */
#define MAX_DRIVES         8
#define COMPAT_DRIVES      4
#if _WORD_SIZE > 2
#define MAX_SECS	 256	/* controller can transfer this many sectors */
#else
#define MAX_SECS	 127	/* but not to a 16 bit process */
#endif
#define MAX_ERRORS         4	/* how often to try rd/wt before quitting */
#define NR_MINORS       (MAX_DRIVES * DEV_PER_DRIVE)
#define SUB_PER_DRIVE	(NR_PARTITIONS * NR_PARTITIONS)
#define NR_SUBDEVS	(MAX_DRIVES * SUB_PER_DRIVE)
#define DELAY_USECS     1000	/* controller timeout in microseconds */
#define DELAY_TICKS 	   1	/* controller timeout in ticks */
#define DEF_TIMEOUT_TICKS 	300	/* controller timeout in ticks */
#define RECOVERY_USECS 500000	/* controller recovery time in microseconds */
#define RECOVERY_TICKS    30	/* controller recovery time in ticks */
#define INITIALIZED	0x01	/* drive is initialized */
#define DEAF		0x02	/* controller must be reset */
#define SMART		0x04	/* drive supports ATA commands */
#if ENABLE_ATAPI
#define ATAPI		0x08	/* it is an ATAPI device */
#else
#define ATAPI		   0	/* don't bother with ATAPI; optimise out */
#endif
#define IDENTIFIED	0x10	/* w_identify done successfully */
#define IGNORING	0x20	/* w_identify failed once */

/* Timeouts and max retries. */
int timeout_ticks = DEF_TIMEOUT_TICKS, max_errors = MAX_ERRORS;
long w_standard_timeouts = 0, w_pci_debug = 0, w_instance = 0,
	disable_dma = 0, atapi_debug = 0, w_identify_wakeup_ticks = WAKEUP_TICKS,
	wakeup_ticks = WAKEUP_TICKS;

int w_testing = 0, w_silent = 0;

int w_next_drive = 0;

/* Variables. */

/* The struct wini is indexed by controller first, then drive (0-3).
 * Controller 0 is always the 'compatability' ide controller, at
 * the fixed locations, whether present or not.
 */
PRIVATE struct wini {		/* main drive struct, one entry per drive */
  unsigned state;		/* drive state: deaf, initialized, dead */
  unsigned short w_status;	/* device status register */
  unsigned base_cmd;		/* command base register */
  unsigned base_ctl;		/* control base register */
  unsigned base_dma;		/* dma base register */
  unsigned irq;			/* interrupt request line */
  unsigned irq_mask;		/* 1 << irq */
  unsigned irq_need_ack;	/* irq needs to be acknowledged */
  int irq_hook_id;		/* id of irq hook at the kernel */
  int lba48;			/* supports lba48 */
  int dma;			/* supports dma */
  unsigned lcylinders;		/* logical number of cylinders (BIOS) */
  unsigned lheads;		/* logical number of heads */
  unsigned lsectors;		/* logical number of sectors per track */
  unsigned pcylinders;		/* physical number of cylinders (translated) */
  unsigned pheads;		/* physical number of heads */
  unsigned psectors;		/* physical number of sectors per track */
  unsigned ldhpref;		/* top four bytes of the LDH (head) register */
  unsigned precomp;		/* write precompensation cylinder / 4 */
  unsigned max_count;		/* max request for this drive */
  unsigned open_ct;		/* in-use count */
  struct device part[DEV_PER_DRIVE];	/* disks and partitions */
  struct device subpart[SUB_PER_DRIVE];	/* subpartitions */
} wini[MAX_DRIVES], *w_wn;

PRIVATE int w_device = -1;
PRIVATE int w_controller = -1;
PRIVATE int w_major = -1;
PRIVATE char w_id_string[40];

PRIVATE int win_tasknr;			/* my task number */
PRIVATE int w_command;			/* current command in execution */
PRIVATE u8_t w_byteval;			/* used for SYS_IRQCTL */
PRIVATE int w_drive;			/* selected drive */
PRIVATE int w_controller;		/* selected controller */
PRIVATE struct device *w_dv;		/* device's base and size */

/* Unfortunately, DMA_SECTORS and DMA_BUF_SIZE are already defined libdriver
 * for 'tmp_buf'.
 */
#define ATA_DMA_SECTORS	64
#define ATA_DMA_BUF_SIZE	(ATA_DMA_SECTORS*SECTOR_SIZE)

PRIVATE char dma_buf[ATA_DMA_BUF_SIZE];
PRIVATE phys_bytes dma_buf_phys;

#define N_PRDTE	1024	/* Should be enough for large requests */

PRIVATE struct prdte
{
	u32_t prdte_base;
	u16_t prdte_count;
	u8_t prdte_reserved;
	u8_t prdte_flags;
} prdt[N_PRDTE];
PRIVATE phys_bytes prdt_phys;

#define PRDTE_FL_EOT	0x80	/* End of table */

/* Some IDE devices announce themselves as RAID controllers */
PRIVATE struct
{
	u16_t vendor;
	u16_t device;
} raid_table[]=
{
	{ 0x1106,	0x3149	},	/* VIA VT6420 */
	{ 0,		0	}	/* end of list */
};

FORWARD _PROTOTYPE( void init_params, (void) 				);
FORWARD _PROTOTYPE( void init_drive, (struct wini *w, int base_cmd,
	int base_ctl, int base_dma, int irq, int ack, int hook,
							int drive)	);
FORWARD _PROTOTYPE( void init_params_pci, (int) 			);
FORWARD _PROTOTYPE( int w_do_open, (struct driver *dp, message *m_ptr) 	);
FORWARD _PROTOTYPE( struct device *w_prepare, (int dev) 		);
FORWARD _PROTOTYPE( int w_identify, (void)				);
FORWARD _PROTOTYPE( char *w_name, (void) 				);
FORWARD _PROTOTYPE( int w_specify, (void) 				);
FORWARD _PROTOTYPE( int w_io_test, (void) 				);
FORWARD _PROTOTYPE( int w_transfer, (int proc_nr, int opcode, u64_t position,
				iovec_t *iov, unsigned nr_req, int safe));
FORWARD _PROTOTYPE( int com_out, (struct command *cmd) 			);
FORWARD _PROTOTYPE( int com_out_ext, (struct command *cmd)		);
FORWARD _PROTOTYPE( void setup_dma, (unsigned *sizep, int proc_nr,
		iovec_t *iov, int do_write, int *do_copyoutp, int safe)	);
FORWARD _PROTOTYPE( void w_need_reset, (void) 				);
FORWARD _PROTOTYPE( void ack_irqs, (unsigned int) 			);
FORWARD _PROTOTYPE( int w_do_close, (struct driver *dp, message *m_ptr) );
FORWARD _PROTOTYPE( int w_other, (struct driver *dp, message *m_ptr, int));
FORWARD _PROTOTYPE( int w_hw_int, (struct driver *dp, message *m_ptr) 	);
FORWARD _PROTOTYPE( int com_simple, (struct command *cmd) 		);
FORWARD _PROTOTYPE( void w_timeout, (void) 				);
FORWARD _PROTOTYPE( int w_reset, (void) 				);
FORWARD _PROTOTYPE( void w_intr_wait, (void) 				);
FORWARD _PROTOTYPE( int at_intr_wait, (void) 				);
FORWARD _PROTOTYPE( int w_waitfor, (int mask, int value) 		);
FORWARD _PROTOTYPE( int w_waitfor_dma, (int mask, int value) 		);
FORWARD _PROTOTYPE( void w_geometry, (struct partition *entry) 		);
#if ENABLE_ATAPI
FORWARD _PROTOTYPE( int atapi_sendpacket, (u8_t *packet, unsigned cnt) 	);
FORWARD _PROTOTYPE( int atapi_intr_wait, (void) 			);
FORWARD _PROTOTYPE( int atapi_open, (void) 				);
FORWARD _PROTOTYPE( void atapi_close, (void) 				);
FORWARD _PROTOTYPE( int atapi_transfer, (int proc_nr, int opcode,
		u64_t position, iovec_t *iov, unsigned nr_req, int safe));
#endif

#define panic(f,m,n) at_panic(__LINE__, (f), (m), (n))
FORWARD _PROTOTYPE( void at_panic, (int line, char *h, char *msg, int n));

#define sys_voutb(out, n) at_voutb(__LINE__, (out), (n))
FORWARD _PROTOTYPE( int at_voutb, (int line, pvb_pair_t *, int n));
#define sys_vinb(in, n) at_vinb(__LINE__, (in), (n))
FORWARD _PROTOTYPE( int at_vinb, (int line, pvb_pair_t *, int n));

#undef sys_outb
#undef sys_inb
#undef sys_outw
#undef sys_inw
#undef sys_outl
#undef sys_inl

FORWARD _PROTOTYPE( int at_out, (int line, u32_t port, u32_t value,
	char *typename, int type));
FORWARD _PROTOTYPE( int at_in, (int line, u32_t port, u32_t *value,
	char *typename, int type));

#define sys_outb(p, v) at_out(__LINE__, (p), (v), "outb", _DIO_BYTE)
#define sys_inb(p, v) at_in(__LINE__, (p), (v), "inb", _DIO_BYTE)
#define sys_outw(p, v) at_out(__LINE__, (p), (v), "outw", _DIO_WORD)
#define sys_inw(p, v) at_in(__LINE__, (p), (v), "inw", _DIO_WORD)
#define sys_outl(p, v) at_out(__LINE__, (p), (v), "outl", _DIO_LONG)
#define sys_inl(p, v) at_in(__LINE__, (p), (v), "inl", _DIO_LONG)

/* Entry points to this driver. */
PRIVATE struct driver w_dtab = {
  w_name,		/* current device's name */
  w_do_open,		/* open or mount request, initialize device */
  w_do_close,		/* release device */
  do_diocntl,		/* get or set a partition's geometry */
  w_prepare,		/* prepare for I/O on a given minor device */
  w_transfer,		/* do the I/O */
  nop_cleanup,		/* nothing to clean up */
  w_geometry,		/* tell the geometry of the disk */
  nop_signal,		/* no cleanup needed on shutdown */
  nop_alarm,		/* ignore leftover alarms */
  nop_cancel,		/* ignore CANCELs */
  nop_select,		/* ignore selects */
  w_other,		/* catch-all for unrecognized commands and ioctls */
  w_hw_int		/* leftover hardware interrupts */
};

/*===========================================================================*
 *				at_winchester_task			     *
 *===========================================================================*/
PUBLIC int main(int argc, char *argv[])
{
/* Install signal handlers. Ask PM to transform signal into message. */
  struct sigaction sa;

  sa.sa_handler = SIG_MESS;
  sigemptyset(&sa.sa_mask);
  sa.sa_flags = 0;
  if (sigaction(SIGTERM,&sa,NULL)<0) panic("AT","sigaction failed", errno);

  /* Set special disk parameters then call the generic main loop. */
  env_setargs(argc, argv);
  init_params();
  signal(SIGTERM, SIG_IGN);
  driver_task(&w_dtab);
  return(OK);
}

/*===========================================================================*
 *				init_params				     *
 *===========================================================================*/
PRIVATE void init_params()
{
/* This routine is called at startup to initialize the drive parameters. */

  u16_t parv[2];
  unsigned int vector, size;
  int drive, nr_drives;
  struct wini *wn;
  u8_t params[16];
  int s;
  long wakeup_secs = WAKEUP_SECS;

  /* Boot variables. */
  env_parse("ata_std_timeout", "d", 0, &w_standard_timeouts, 0, 1);
  env_parse("ata_pci_debug", "d", 0, &w_pci_debug, 0, 1);
  env_parse("ata_instance", "d", 0, &w_instance, 0, 8);
  env_parse("ata_no_dma", "d", 0, &disable_dma, 0, 1);
  env_parse("ata_id_timeout", "d", WAKEUP_SECS, &wakeup_secs, 1, 60);
  env_parse("atapi_debug", "d", 0, &atapi_debug, 0, 1);

  w_identify_wakeup_ticks = wakeup_secs * HZ;

  if(atapi_debug)
	panic("at_wini", "atapi_debug", NO_NUM);

  if(w_identify_wakeup_ticks <= 0) {
	printf("changing wakeup from %d to %d ticks.\n",
		w_identify_wakeup_ticks, WAKEUP_TICKS);
	w_identify_wakeup_ticks = WAKEUP_TICKS;
  }

  if (disable_dma)
	printf("DMA for ATA devices is disabled.\n");

  s= sys_umap(SELF, D, (vir_bytes)dma_buf, sizeof(dma_buf), &dma_buf_phys);
  if (s != 0)
	panic("at_wini", "can't map dma buffer", s);

  s= sys_umap(SELF, D, (vir_bytes)prdt, sizeof(prdt), &prdt_phys);
  if (s != 0)
	panic("at_wini", "can't map prd table", s);

  if (w_instance == 0) {
	  /* Get the number of drives from the BIOS data area */
	  s=sys_readbios(NR_HD_DRIVES_ADDR, params, NR_HD_DRIVES_SIZE);
	  if (s != OK)
  		panic(w_name(), "Couldn't read BIOS", s);
	  if ((nr_drives = params[0]) > 2) nr_drives = 2;

	  for (drive = 0, wn = wini; drive < COMPAT_DRIVES; drive++, wn++) {
		if (drive < nr_drives) {
		    /* Copy the BIOS parameter vector */
		    vector = (drive == 0) ? BIOS_HD0_PARAMS_ADDR :
			BIOS_HD1_PARAMS_ADDR;
		    size = (drive == 0) ? BIOS_HD0_PARAMS_SIZE :
			BIOS_HD1_PARAMS_SIZE;
		    s=sys_readbios(vector, parv, size);
		    if (s != OK)
			panic(w_name(), "Couldn't read BIOS", s);
	
		    /* Calculate the address of the parameters and copy them */
		    s=sys_readbios(hclick_to_physb(parv[1]) + parv[0],
			params, 16L);
		    if (s != OK)
			panic(w_name(),"Couldn't copy parameters", s);
	
		    /* Copy the parameters to the structures of the drive */
		    wn->lcylinders = bp_cylinders(params);
		    wn->lheads = bp_heads(params);
		    wn->lsectors = bp_sectors(params);
		    wn->precomp = bp_precomp(params) >> 2;
		}

		/* Fill in non-BIOS parameters. */
		init_drive(wn,
			drive < 2 ? REG_CMD_BASE0 : REG_CMD_BASE1,
			drive < 2 ? REG_CTL_BASE0 : REG_CTL_BASE1,
			0 /* no DMA */, NO_IRQ, 0, 0, drive);
		w_next_drive++;
  	}
  }

  /* Look for controllers on the pci bus. Skip none the first instance,
   * skip one and then 2 for every instance, for every next instance.
   */
  if (w_instance == 0)
  	init_params_pci(0);
  else
  	init_params_pci(w_instance*2-1);

}

#define ATA_IF_NOTCOMPAT1 (1L << 0)
#define ATA_IF_NOTCOMPAT2 (1L << 2)

/*===========================================================================*
 *				init_drive				     *
 *===========================================================================*/
PRIVATE void init_drive(struct wini *w, int base_cmd, int base_ctl,
	int base_dma, int irq, int ack, int hook, int drive)
{
	w->state = 0;
	w->w_status = 0;
	w->base_cmd = base_cmd;
	w->base_ctl = base_ctl;
	w->base_dma = base_dma;
	if(w_pci_debug)
	   printf("at_wini%d: drive %d: base_cmd 0x%x, base_ctl 0x%x, base_dma 0x%x\n",
		w_instance, w-wini, w->base_cmd, w->base_ctl, w->base_dma);
	w->irq = irq;
	w->irq_mask = 1 << irq;
	w->irq_need_ack = ack;
	w->irq_hook_id = hook;
	w->ldhpref = ldh_init(drive);
	w->max_count = MAX_SECS << SECTOR_SHIFT;
	w->lba48 = 0;
	w->dma = 0;
}

/*===========================================================================*
 *				init_params_pci				     *
 *===========================================================================*/
PRIVATE void init_params_pci(int skip)
{
  int i, r, devind, drive, pci_compat = 0;
  int irq, irq_hook, raid;
  u8_t bcr, scr, interface;
  u16_t vid, did;
  u32_t base_dma, t3;

  pci_init();
  for(drive = w_next_drive; drive < MAX_DRIVES; drive++)
  	wini[drive].state = IGNORING;
  for(r = pci_first_dev(&devind, &vid, &did); r != 0;
	r = pci_next_dev(&devind, &vid, &did)) {

	raid= 0;

  	/* Except class 01h (mass storage), subclass be 01h (ATA).
	 * Also check listed RAID controllers.
  	 */
	bcr= pci_attr_r8(devind, PCI_BCR);
	scr= pci_attr_r8(devind, PCI_SCR);
	interface= pci_attr_r8(devind, PCI_PIFR);
	t3= ((bcr << 16) | (scr << 8) | interface);
  	if (bcr == PCI_BCR_MASS_STORAGE && scr == PCI_MS_IDE)
		;	/* Okay */
	else if (t3 == PCI_T3_RAID)
	{
		for (i= 0; raid_table[i].vendor != 0; i++)
		{
			if (raid_table[i].vendor == vid &&
				raid_table[i].device == did)
			{
				break;
			}
		}
		if (raid_table[i].vendor == 0)
		{
		  	printf(
	"atapci skipping unsupported RAID controller 0x%04x / 0x%04x\n",
				vid, did);
			continue;
		}
		printf("found supported RAID controller\n");
		raid= 1;
	}
	else
		continue;	/* Unsupported device class */

  	/* Found a controller.
  	 * Programming interface register tells us more.
  	 */
  	irq = pci_attr_r8(devind, PCI_ILR);

  	/* Any non-compat drives? */
  	if (raid || (interface & (ATA_IF_NOTCOMPAT1 | ATA_IF_NOTCOMPAT2))) {
  		int s;

		if (w_next_drive >= MAX_DRIVES)
		{
			/* We can't accept more drives, but have to search for
			 * controllers operating in compatibility mode.
			 */
			continue;
		}

  		irq_hook = irq;
  		if (skip > 0) {
  			if (w_pci_debug)
			{
				printf(
				"atapci skipping controller (remain %d)\n",
					skip);
			}
  			skip--;
  			continue;
  		}
		if(pci_reserve_ok(devind) != OK) {
			printf("at_wini%d: pci_reserve %d failed - "
				"ignoring controller!\n",
				w_instance, devind);
			continue;
		}
  		if ((s=sys_irqsetpolicy(irq, 0, &irq_hook)) != OK) {
		  	printf("atapci: couldn't set IRQ policy %d\n", irq);
		  	continue;
		}
		if ((s=sys_irqenable(&irq_hook)) != OK) {
			printf("atapci: couldn't enable IRQ line %d\n", irq);
		  	continue;
		}
  	} else if(w_pci_debug) printf("at_wini%d: dev %d: only compat drives\n", w_instance, devind); 

  	base_dma = pci_attr_r32(devind, PCI_BAR_5) & 0xfffffffc;

  	/* Primary channel not in compatability mode? */
  	if (raid || (interface & ATA_IF_NOTCOMPAT1)) {
  		u32_t base_cmd, base_ctl;

  		base_cmd = pci_attr_r32(devind, PCI_BAR) & 0xfffffffc;
  		base_ctl = pci_attr_r32(devind, PCI_BAR_2) & 0xfffffffc;
  		if (base_cmd != REG_CMD_BASE0 && base_cmd != REG_CMD_BASE1) {
	  		init_drive(&wini[w_next_drive],
	  			base_cmd, base_ctl+PCI_CTL_OFF,
				base_dma, irq, 1, irq_hook, 0);
  			init_drive(&wini[w_next_drive+1],
  				base_cmd, base_ctl+PCI_CTL_OFF,
				base_dma, irq, 1, irq_hook, 1);
	  		if (w_pci_debug)
		  		printf("at_wini%d: atapci %d: 0x%x 0x%x irq %d\n", w_instance, devind, base_cmd, base_ctl, irq);
			w_next_drive += 2;
  		} else printf("at_wini%d: atapci: ignored drives on primary channel, base %x\n", w_instance, base_cmd);
  	}
	else
	{
		/* Update base_dma for compatibility device */
		for (i= 0; i<MAX_DRIVES; i++)
		{
			if (wini[i].base_cmd == REG_CMD_BASE0) {
				wini[i].base_dma= base_dma;
				if(w_pci_debug)
	   			  printf("at_wini%d: drive %d: base_dma 0x%x\n",
					w_instance, i, wini[i].base_dma);
				pci_compat = 1;
			}
		}
	}

  	/* Secondary channel not in compatability mode? */
  	if (raid || (interface & ATA_IF_NOTCOMPAT2)) {
  		u32_t base_cmd, base_ctl;

  		base_cmd = pci_attr_r32(devind, PCI_BAR_3) & 0xfffffffc;
  		base_ctl = pci_attr_r32(devind, PCI_BAR_4) & 0xfffffffc;
		if (base_dma != 0)
			base_dma += PCI_DMA_2ND_OFF;
  		if (base_cmd != REG_CMD_BASE0 && base_cmd != REG_CMD_BASE1) {
  			init_drive(&wini[w_next_drive],
  				base_cmd, base_ctl+PCI_CTL_OFF, base_dma,
				irq, 1, irq_hook, 2);
	  		init_drive(&wini[w_next_drive+1],
	  			base_cmd, base_ctl+PCI_CTL_OFF, base_dma,
				irq, 1, irq_hook, 3);
	  		if (w_pci_debug)
  			  printf("at_wini%d: atapci %d: 0x%x 0x%x irq %d\n",
				w_instance, devind, base_cmd, base_ctl, irq);
			w_next_drive += 2;
  		} else printf("at_wini%d: atapci: ignored drives on "
			"secondary channel, base %x\n", w_instance, base_cmd);
  	}
	else
	{
		/* Update base_dma for compatibility device */
		for (i= 0; i<MAX_DRIVES; i++)
		{
			if (wini[i].base_cmd == REG_CMD_BASE1 && base_dma != 0) {
				wini[i].base_dma= base_dma+PCI_DMA_2ND_OFF;
	  			if (w_pci_debug)
	   			  printf("at_wini%d: drive %d: base_dma 0x%x\n",
					w_instance, i, wini[i].base_dma);
				pci_compat = 1;
			}
		}
	}

	if(pci_compat) {
		if(pci_reserve_ok(devind) != OK) {
			printf("at_wini%d (compat): pci_reserve %d failed!\n",
				w_instance, devind);
		}
	}
  }
}

/*===========================================================================*
 *				w_do_open				     *
 *===========================================================================*/
PRIVATE int w_do_open(dp, m_ptr)
struct driver *dp;
message *m_ptr;
{
/* Device open: Initialize the controller and read the partition table. */

  struct wini *wn;

  if (w_prepare(m_ptr->DEVICE) == NIL_DEV) return(ENXIO);

  wn = w_wn;

  /* If we've probed it before and it failed, don't probe it again. */
  if (wn->state & IGNORING) return ENXIO;

  /* If we haven't identified it yet, or it's gone deaf, 
   * (re-)identify it.
   */
  if (!(wn->state & IDENTIFIED) || (wn->state & DEAF)) {
	/* Try to identify the device. */
	if (w_identify() != OK) {
#if VERBOSE
  		printf("%s: probe failed\n", w_name());
#endif
		if (wn->state & DEAF) w_reset();
		wn->state = IGNORING;
		return(ENXIO);
	}
	  /* Do a test transaction unless it's a CD drive (then
	   * we can believe the controller, and a test may fail
	   * due to no CD being in the drive). If it fails, ignore
	   * the device forever.
	   */
	  if (!(wn->state & ATAPI) && w_io_test() != OK) {
  		wn->state |= IGNORING;
	  	return(ENXIO);
	  }

#if VERBOSE
	  printf("%s: AT driver detected ", w_name());
	  if (wn->state & (SMART|ATAPI)) {
		printf("%.40s\n", w_id_string);
	  } else {
		printf("%ux%ux%u\n", wn->pcylinders, wn->pheads, wn->psectors);
	  }
#endif
  }

#if ENABLE_ATAPI
   if ((wn->state & ATAPI) && (m_ptr->COUNT & W_BIT))
	return(EACCES);
#endif

  /* Partition the drive if it's being opened for the first time,
   * or being opened after being closed.
   */
  if (wn->open_ct == 0) {
#if ENABLE_ATAPI
	if (wn->state & ATAPI) {
		int r;
		if ((r = atapi_open()) != OK) return(r);
	}
#endif

	/* Partition the disk. */
	partition(&w_dtab, w_drive * DEV_PER_DRIVE, P_PRIMARY, wn->state & ATAPI);
  }
  wn->open_ct++;
  return(OK);
}

/*===========================================================================*
 *				w_prepare				     *
 *===========================================================================*/
PRIVATE struct device *w_prepare(int device)
{
/* Prepare for I/O on a device. */
struct wini *prev_wn;
prev_wn = w_wn;
  w_device = device;

  if (device < NR_MINORS) {			/* d0, d0p[0-3], d1, ... */
	w_drive = device / DEV_PER_DRIVE;	/* save drive number */
	w_wn = &wini[w_drive];
	w_dv = &w_wn->part[device % DEV_PER_DRIVE];
  } else
  if ((unsigned) (device -= MINOR_d0p0s0) < NR_SUBDEVS) {/*d[0-7]p[0-3]s[0-3]*/
	w_drive = device / SUB_PER_DRIVE;
	w_wn = &wini[w_drive];
	w_dv = &w_wn->subpart[device % SUB_PER_DRIVE];
  } else {
  	w_device = -1;
	return(NIL_DEV);
  }
  return(w_dv);
}

/*===========================================================================*
 *				w_identify				     *
 *===========================================================================*/
PRIVATE int w_identify()
{
/* Find out if a device exists, if it is an old AT disk, or a newer ATA
 * drive, a removable media device, etc.
 */

  struct wini *wn = w_wn;
  struct command cmd;
  int i, s;
  int id_dma, ultra_dma;
  u32_t dma_base;
  u16_t w;
  unsigned long dma_status;
  unsigned long size;
  int prev_wakeup;
  int r;
#define id_byte(n)	(&tmp_buf[2 * (n)])
#define id_word(n)	(((u16_t) id_byte(n)[0] <<  0) \
			|((u16_t) id_byte(n)[1] <<  8))
#define id_longword(n)	(((u32_t) id_byte(n)[0] <<  0) \
			|((u32_t) id_byte(n)[1] <<  8) \
			|((u32_t) id_byte(n)[2] << 16) \
			|((u32_t) id_byte(n)[3] << 24))

  /* Try to identify the device. */
  cmd.ldh     = wn->ldhpref;
  cmd.command = ATA_IDENTIFY;

  /* In testing mode, a drive will get ignored at the first timeout. */
  w_testing = 1;

  /* Execute *_IDENTIFY with configured *_IDENTIFY timeout. */
  prev_wakeup = wakeup_ticks;
  wakeup_ticks = w_identify_wakeup_ticks;
  r = com_simple(&cmd);

  if (r == OK && w_waitfor(STATUS_DRQ, STATUS_DRQ) &&
	!(wn->w_status & (STATUS_ERR|STATUS_WF))) {

	/* Device information. */
	if ((s=sys_insw(wn->base_cmd + REG_DATA, SELF, tmp_buf, SECTOR_SIZE)) != OK)
		panic(w_name(),"Call to sys_insw() failed", s);

#if 0
	if (id_word(0) & ID_GEN_NOT_ATA)
	{
		printf("%s: not an ATA device?\n", w_name());
  		wakeup_ticks = prev_wakeup;
		w_testing = 0;
		return ERR;
	}
#endif

	/* This is an ATA device. */
	wn->state |= SMART;

	/* Why are the strings byte swapped??? */
	for (i = 0; i < 40; i++) w_id_string[i] = id_byte(27)[i^1];

	/* Preferred CHS translation mode. */
	wn->pcylinders = id_word(1);
	wn->pheads = id_word(3);
	wn->psectors = id_word(6);
	size = (u32_t) wn->pcylinders * wn->pheads * wn->psectors;

	w= id_word(ID_CAPABILITIES);
	if ((w & ID_CAP_LBA) && size > 512L*1024*2) {
		/* Drive is LBA capable and is big enough to trust it to
		 * not make a mess of it.
		 */
		wn->ldhpref |= LDH_LBA;
		size = id_longword(60);

		w= id_word(ID_CSS);
		if (size < LBA48_CHECK_SIZE)
		{
			/* No need to check for LBA48 */
		}
		else if (w & ID_CSS_LBA48) {
			/* Drive is LBA48 capable (and LBA48 is turned on). */
			if (id_longword(102)) {
				/* If no. of sectors doesn't fit in 32 bits,
				 * trunacte to this. So it's LBA32 for now.
				 * This can still address devices up to 2TB
				 * though.
				 */
				size = ULONG_MAX;
			} else {
				/* Actual number of sectors fits in 32 bits. */
				size = id_longword(100);
			}
			wn->lba48 = 1;
		}

		/* Check for DMA. Assume that only LBA capable devices can do
		 * DMA.
		 */
		w= id_word(ID_CAPABILITIES);
		id_dma= !!(w & ID_CAP_DMA);
		w= id_byte(ID_FIELD_VALIDITY)[0];
		ultra_dma= !!(w & ID_FV_88);
		dma_base= wn->base_dma;
		if (dma_base)
		{
			if (sys_inb(dma_base + DMA_STATUS, &dma_status) != OK)
			{
				panic(w_name(),
					"unable to read DMA status register",
					NO_NUM);
			}
		}
		if (disable_dma)
			;	/* DMA is disabled */
		else if (id_dma && dma_base)
		{
			w= id_word(ID_MULTIWORD_DMA);
			if (w & (ID_MWDMA_2_SUP|ID_MWDMA_1_SUP|ID_MWDMA_0_SUP))
			{
				printf(
				"%s: multiword DMA modes supported:%s%s%s\n",
					w_name(),
					(w & ID_MWDMA_0_SUP) ? " 0" : "",
					(w & ID_MWDMA_1_SUP) ? " 1" : "",
					(w & ID_MWDMA_2_SUP) ? " 2" : "");
			}
			if (w & (ID_MWDMA_0_SEL|ID_MWDMA_1_SEL|ID_MWDMA_2_SEL))
			{
				printf(
				"%s: multiword DMA mode selected:%s%s%s\n",
					w_name(),
					(w & ID_MWDMA_0_SEL) ? " 0" : "",
					(w & ID_MWDMA_1_SEL) ? " 1" : "",
					(w & ID_MWDMA_2_SEL) ? " 2" : "");
			}
			if (ultra_dma) 
			{
				w= id_word(ID_ULTRA_DMA);
				if (w & (ID_UDMA_0_SUP|ID_UDMA_1_SUP|
					ID_UDMA_2_SUP|ID_UDMA_3_SUP|
					ID_UDMA_4_SUP|ID_UDMA_5_SUP))
				{
					printf(
				"%s: Ultra DMA modes supported:%s%s%s%s%s%s\n",
					w_name(),
					(w & ID_UDMA_0_SUP) ? " 0" : "",
					(w & ID_UDMA_1_SUP) ? " 1" : "",
					(w & ID_UDMA_2_SUP) ? " 2" : "",
					(w & ID_UDMA_3_SUP) ? " 3" : "",
					(w & ID_UDMA_4_SUP) ? " 4" : "",
					(w & ID_UDMA_5_SUP) ? " 5" : "");
				}
				if (w & (ID_UDMA_0_SEL|ID_UDMA_1_SEL|
					ID_UDMA_2_SEL|ID_UDMA_3_SEL|
					ID_UDMA_4_SEL|ID_UDMA_5_SEL))
				{
					printf(
				"%s: Ultra DMA mode selected:%s%s%s%s%s%s\n",
					w_name(),
					(w & ID_UDMA_0_SEL) ? " 0" : "",
					(w & ID_UDMA_1_SEL) ? " 1" : "",
					(w & ID_UDMA_2_SEL) ? " 2" : "",
					(w & ID_UDMA_3_SEL) ? " 3" : "",
					(w & ID_UDMA_4_SEL) ? " 4" : "",
					(w & ID_UDMA_5_SEL) ? " 5" : "");
				}
			}
			wn->dma= 1;
		}
		else if (id_dma || dma_base)
		{
			printf("id_dma %d, dma_base 0x%x\n", id_dma, dma_base);
		}
		else
			printf("no DMA support\n");

#if 0
		if (wn->dma && wn == &wini[0])
		{
			printf("disabling DMA for drive 0\n");
			wn->dma= 0;
		}
#endif
	}

	if (wn->lcylinders == 0 || wn->lheads == 0 || wn->lsectors == 0) {
		/* No BIOS parameters?  Then make some up. */
		wn->lcylinders = wn->pcylinders;
		wn->lheads = wn->pheads;
		wn->lsectors = wn->psectors;
		while (wn->lcylinders > 1024) {
			wn->lheads *= 2;
			wn->lcylinders /= 2;
		}
	}
#if ENABLE_ATAPI
  } else
  if (cmd.command = ATAPI_IDENTIFY,
	com_simple(&cmd) == OK && w_waitfor(STATUS_DRQ, STATUS_DRQ) &&
	!(wn->w_status & (STATUS_ERR|STATUS_WF))) {
	/* An ATAPI device. */
	wn->state |= ATAPI;

	/* Device information. */
	if ((s=sys_insw(wn->base_cmd + REG_DATA, SELF, tmp_buf, 512)) != OK)
		panic(w_name(),"Call to sys_insw() failed", s);

	/* Why are the strings byte swapped??? */
	for (i = 0; i < 40; i++) w_id_string[i] = id_byte(27)[i^1];

	size = 0;	/* Size set later. */
#endif
  } else {
	/* Not an ATA device; no translations, no special features.  Don't
	 * touch it unless the BIOS knows about it.
	 */
	if (wn->lcylinders == 0) { 
  		wakeup_ticks = prev_wakeup;
		w_testing = 0;
		return(ERR);
	}	/* no BIOS parameters */
	wn->pcylinders = wn->lcylinders;
	wn->pheads = wn->lheads;
	wn->psectors = wn->lsectors;
	size = (u32_t) wn->pcylinders * wn->pheads * wn->psectors;
  }

  /* Restore wakeup_ticks and unset testing mode. */
  wakeup_ticks = prev_wakeup;
  w_testing = 0;

  /* Size of the whole drive */
  wn->part[0].dv_size = mul64u(size, SECTOR_SIZE);

  /* Reset/calibrate (where necessary) */
  if (w_specify() != OK && w_specify() != OK) {
  	return(ERR);
  }

  if (wn->irq == NO_IRQ) {
	  /* Everything looks OK; register IRQ so we can stop polling. */
	  wn->irq = w_drive < 2 ? AT_WINI_0_IRQ : AT_WINI_1_IRQ;
	  wn->irq_hook_id = wn->irq;	/* id to be returned if interrupt occurs */
	  if ((s=sys_irqsetpolicy(wn->irq, IRQ_REENABLE, &wn->irq_hook_id)) != OK) 
	  	panic(w_name(), "couldn't set IRQ policy", s);
	  if ((s=sys_irqenable(&wn->irq_hook_id)) != OK)
	  	panic(w_name(), "couldn't enable IRQ line", s);
  }
  wn->state |= IDENTIFIED;
  return(OK);
}

/*===========================================================================*
 *				w_name					     *
 *===========================================================================*/
PRIVATE char *w_name()
{
/* Return a name for the current device. */
  static char name[] = "AT0-D0";

  name[2] = '0' + w_instance;
  name[5] = '0' + w_drive;
  return name;
}

/*===========================================================================*
 *				w_io_test				     *
 *===========================================================================*/
PRIVATE int w_io_test(void)
{
	int r, save_dev;
	int save_timeout, save_errors, save_wakeup;
	iovec_t iov;
#ifdef CD_SECTOR_SIZE
	static char buf[CD_SECTOR_SIZE];
#else
	static char buf[SECTOR_SIZE];
#endif

	iov.iov_addr = (vir_bytes) buf;
	iov.iov_size = sizeof(buf);
	save_dev = w_device;

	/* Reduce timeout values for this test transaction. */
	save_timeout = timeout_ticks;
	save_errors = max_errors;
	save_wakeup = wakeup_ticks;

	if (!w_standard_timeouts) {
		timeout_ticks = HZ * 4;
		wakeup_ticks = HZ * 6;
		max_errors = 3;
	}

	w_testing = 1;

	/* Try I/O on the actual drive (not any (sub)partition). */
 	if (w_prepare(w_drive * DEV_PER_DRIVE) == NIL_DEV)
 		panic(w_name(), "Couldn't switch devices", NO_NUM);

	r = w_transfer(SELF, DEV_GATHER_S, cvu64(0), &iov, 1, 0);

	/* Switch back. */
 	if (w_prepare(save_dev) == NIL_DEV)
 		panic(w_name(), "Couldn't switch back devices", NO_NUM);

 	/* Restore parameters. */
	timeout_ticks = save_timeout;
	max_errors = save_errors;
	wakeup_ticks = save_wakeup;
	w_testing = 0;

 	/* Test if everything worked. */
	if (r != OK || iov.iov_size != 0) {
		return ERR;
	}

	/* Everything worked. */

	return OK;
}

/*===========================================================================*
 *				w_specify				     *
 *===========================================================================*/
PRIVATE int w_specify()
{
/* Routine to initialize the drive after boot or when a reset is needed. */

  struct wini *wn = w_wn;
  struct command cmd;

  if ((wn->state & DEAF) && w_reset() != OK) {
  	return(ERR);
  }

  if (!(wn->state & ATAPI)) {
	/* Specify parameters: precompensation, number of heads and sectors. */
	cmd.precomp = wn->precomp;
	cmd.count   = wn->psectors;
	cmd.ldh     = w_wn->ldhpref | (wn->pheads - 1);
	cmd.command = CMD_SPECIFY;		/* Specify some parameters */

	/* Output command block and see if controller accepts the parameters. */
	if (com_simple(&cmd) != OK) return(ERR);

	if (!(wn->state & SMART)) {
		/* Calibrate an old disk. */
		cmd.sector  = 0;
		cmd.cyl_lo  = 0;
		cmd.cyl_hi  = 0;
		cmd.ldh     = w_wn->ldhpref;
		cmd.command = CMD_RECALIBRATE;

		if (com_simple(&cmd) != OK) return(ERR);
	}
  }
  wn->state |= INITIALIZED;
  return(OK);
}

/*===========================================================================*
 *				do_transfer				     *
 *===========================================================================*/
PRIVATE int do_transfer(struct wini *wn, unsigned int precomp,
	unsigned int count, unsigned int sector,
	unsigned int opcode, int do_dma)
{
  	struct command cmd;
	unsigned int sector_high;
	unsigned secspcyl = wn->pheads * wn->psectors;
	int do_lba48;

	sector_high= 0;	/* For future extensions */

	do_lba48= 0;
	if (sector >= LBA48_CHECK_SIZE || sector_high != 0)
	{
		if (wn->lba48)
			do_lba48= 1;
		else if (sector > LBA_MAX_SIZE || sector_high != 0)
		{
			/* Strange sector count for LBA device */
			return EIO;
		}
	}

	cmd.precomp = precomp;
	cmd.count   = count;
	if (do_dma)
	{
		cmd.command = opcode == DEV_SCATTER_S ? CMD_WRITE_DMA :
			CMD_READ_DMA;
	}
	else
		cmd.command = opcode == DEV_SCATTER_S ? CMD_WRITE : CMD_READ;

	if (do_lba48) {
		if (do_dma)
		{
			cmd.command = ((opcode == DEV_SCATTER_S) ?
				CMD_WRITE_DMA_EXT : CMD_READ_DMA_EXT);
		}
		else
		{
			cmd.command = ((opcode == DEV_SCATTER_S) ?
				CMD_WRITE_EXT : CMD_READ_EXT);
		}
		cmd.count_prev= (count >> 8);
		cmd.sector  = (sector >>  0) & 0xFF;
		cmd.cyl_lo  = (sector >>  8) & 0xFF;
		cmd.cyl_hi  = (sector >> 16) & 0xFF;
		cmd.sector_prev= (sector >> 24) & 0xFF;
		cmd.cyl_lo_prev= (sector_high) & 0xFF;
		cmd.cyl_hi_prev= (sector_high >> 8) & 0xFF;
		cmd.ldh     = wn->ldhpref;

		return com_out_ext(&cmd);
	} else if (wn->ldhpref & LDH_LBA) {
		cmd.sector  = (sector >>  0) & 0xFF;
		cmd.cyl_lo  = (sector >>  8) & 0xFF;
		cmd.cyl_hi  = (sector >> 16) & 0xFF;
		cmd.ldh     = wn->ldhpref | ((sector >> 24) & 0xF);
	} else {
  		int cylinder, head, sec;
		cylinder = sector / secspcyl;
		head = (sector % secspcyl) / wn->psectors;
		sec = sector % wn->psectors;
		cmd.sector  = sec + 1;
		cmd.cyl_lo  = cylinder & BYTE;
		cmd.cyl_hi  = (cylinder >> 8) & BYTE;
		cmd.ldh     = wn->ldhpref | head;
	}

	return com_out(&cmd);
}

/*===========================================================================*
 *				w_transfer				     *
 *===========================================================================*/
PRIVATE int w_transfer(proc_nr, opcode, position, iov, nr_req, safe)
int proc_nr;			/* process doing the request */
int opcode;			/* DEV_GATHER_S or DEV_SCATTER_S */
u64_t position;			/* offset on device to read or write */
iovec_t *iov;			/* pointer to read or write request vector */
unsigned nr_req;		/* length of request vector */
int safe;			/* iov contains addresses (0) or grants? */
{
  struct wini *wn = w_wn;
  iovec_t *iop, *iov_end = iov + nr_req;
  int n, r, s, errors, do_dma, do_write, do_copyout;
  unsigned long v, block, w_status;
  u64_t dv_size = w_dv->dv_size;
  unsigned cylinder, head, sector, nbytes;
  unsigned dma_buf_offset;
  size_t addr_offset = 0;

#if ENABLE_ATAPI
  if (w_wn->state & ATAPI) {
	return atapi_transfer(proc_nr, opcode, position, iov, nr_req, safe);
  }
#endif

  /* Check disk address. */
  if (rem64u(position, SECTOR_SIZE) != 0) return(EINVAL);

  errors = 0;

  while (nr_req > 0) {
	/* How many bytes to transfer? */
	nbytes = 0;
	for (iop = iov; iop < iov_end; iop++) nbytes += iop->iov_size;
	if ((nbytes & SECTOR_MASK) != 0) return(EINVAL);

	/* Which block on disk and how close to EOF? */
	if (cmp64(position, dv_size) >= 0) return(OK);		/* At EOF */
	if (cmp64(add64ul(position, nbytes), dv_size) > 0)
		nbytes = diff64(dv_size, position);
	block = div64u(add64(w_dv->dv_base, position), SECTOR_SIZE);

	do_dma= wn->dma;
	do_write= (opcode == DEV_SCATTER_S);
	
	if (nbytes >= wn->max_count) {
		/* The drive can't do more then max_count at once. */
		nbytes = wn->max_count;
	}

	/* First check to see if a reinitialization is needed. */
	if (!(wn->state & INITIALIZED) && w_specify() != OK) return(EIO);

	if (do_dma)
	{
		setup_dma(&nbytes, proc_nr, iov, do_write, &do_copyout, safe);
#if 0
		printf("nbytes = %d\n", nbytes);
#endif
	}

	/* Tell the controller to transfer nbytes bytes. */
	r = do_transfer(wn, wn->precomp, (nbytes >> SECTOR_SHIFT),
		block, opcode, do_dma);

	if (opcode == DEV_SCATTER_S) {
		/* The specs call for a 400 ns wait after issuing the command.
		 * Reading the alternate status register is the suggested 
		 * way to implement this wait.
		 */
		if (sys_inb((wn->base_ctl+REG_CTL_ALTSTAT), &w_status) != OK)
			panic(w_name(), "couldn't get status", NO_NUM);
	}

	if (do_dma)
	{
		/* Wait for the interrupt, check DMA status and optionally
		 * copy out.
		 */

		if ((r = at_intr_wait()) != OK) 
		{
			/* Don't retry if sector marked bad or too many
			 * errors.
			 */
			if (r == ERR_BAD_SECTOR || ++errors == max_errors) {
				w_command = CMD_IDLE;
				return(EIO);
			}
			continue;
		}

		/* Wait for DMA_ST_INT to get set */
		w_waitfor_dma(DMA_ST_INT, DMA_ST_INT);

		r= sys_inb(wn->base_dma + DMA_STATUS, &v);
		if (r != 0) panic("at_wini", "w_transfer: sys_inb failed", r);

#if 0
		printf("dma_status: 0x%x\n", v);
#endif
		if (!(v & DMA_ST_INT))
		{
			/* DMA did not complete successfully */
			if (v & DMA_ST_BM_ACTIVE)
				panic(w_name(), "DMA did not complete", NO_NUM);
			else if (v & DMA_ST_ERROR)
			{
				printf("at_wini: DMA error\n");
				r= EIO;
				break;
			}
			else
			{
#if 0
				printf("DMA buffer too small\n");
#endif
				panic(w_name(), "DMA buffer too small", NO_NUM);
			}
		}
		else if (v & DMA_ST_BM_ACTIVE)
			panic(w_name(), "DMA buffer too large", NO_NUM);

		dma_buf_offset= 0;
		while (r == OK && nbytes > 0)
		{
			n= iov->iov_size;
			if (n > nbytes)
				n= nbytes;

			if (do_copyout)
			{
				if(safe) {
				   s= sys_safecopyto(proc_nr, iov->iov_addr,
					addr_offset,
					(vir_bytes)dma_buf+dma_buf_offset, n, D);
				} else {
				   s= sys_vircopy(SELF, D,
					(vir_bytes)dma_buf+dma_buf_offset, 
					proc_nr, D,
					iov->iov_addr + addr_offset, n);
				}
				if (s != OK)
				{
					panic(w_name(),
					"w_transfer: sys_vircopy failed",
						s);
				}
			}

			/* Book the bytes successfully transferred. */
			nbytes -= n;
			position= add64ul(position, n);
			if ((iov->iov_size -= n) == 0) {
				iov++; nr_req--; addr_offset = 0;
			}
			dma_buf_offset += n;
		}
	}

	while (r == OK && nbytes > 0) {
		/* For each sector, wait for an interrupt and fetch the data
		 * (read), or supply data to the controller and wait for an
		 * interrupt (write).
		 */

		if (opcode == DEV_GATHER_S) {
			/* First an interrupt, then data. */
			if ((r = at_intr_wait()) != OK) {
				/* An error, send data to the bit bucket. */
				if (w_wn->w_status & STATUS_DRQ) {
					if ((s=sys_insw(wn->base_cmd+REG_DATA,
						SELF, tmp_buf,
						SECTOR_SIZE)) != OK)
					{
						panic(w_name(),
						"Call to sys_insw() failed",
							s);
					}
				}
				break;
			}
		}

		/* Wait for busy to clear. */
		if (!w_waitfor(STATUS_BSY, 0)) { r = ERR; break; }

		/* Wait for data transfer requested. */
		if (!w_waitfor(STATUS_DRQ, STATUS_DRQ)) { r = ERR; break; }

		/* Copy bytes to or from the device's buffer. */
		if (opcode == DEV_GATHER_S) {
		   if(safe) {
			s=sys_safe_insw(wn->base_cmd + REG_DATA, proc_nr, 
				(void *) (iov->iov_addr), addr_offset,
					SECTOR_SIZE);
		   } else {
			s=sys_insw(wn->base_cmd + REG_DATA, proc_nr, 
				(void *) (iov->iov_addr + addr_offset),
					SECTOR_SIZE);
		   }
		   if(s != OK) {
			panic(w_name(),"Call to sys_insw() failed", s);
		   }
		} else {
		   if(safe) {
			s=sys_safe_outsw(wn->base_cmd + REG_DATA, proc_nr,
				(void *) (iov->iov_addr), addr_offset,
				SECTOR_SIZE);
		   } else {
			s=sys_outsw(wn->base_cmd + REG_DATA, proc_nr,
				(void *) (iov->iov_addr + addr_offset),
				SECTOR_SIZE);
		   }

		   if(s != OK) {
		  	panic(w_name(),"Call to sys_outsw() failed",
			  	s);
		   }

			/* Data sent, wait for an interrupt. */
			if ((r = at_intr_wait()) != OK) break;
		}

		/* Book the bytes successfully transferred. */
		nbytes -= SECTOR_SIZE;
		position= add64u(position, SECTOR_SIZE);
		addr_offset += SECTOR_SIZE;
		if ((iov->iov_size -= SECTOR_SIZE) == 0) {
			iov++;
			nr_req--;
			addr_offset = 0;
		}
	}

	/* Any errors? */
	if (r != OK) {
		/* Don't retry if sector marked bad or too many errors. */
		if (r == ERR_BAD_SECTOR || ++errors == max_errors) {
			w_command = CMD_IDLE;
			return(EIO);
		}
	}
  }

  w_command = CMD_IDLE;
  return(OK);
}

/*===========================================================================*
 *				com_out					     *
 *===========================================================================*/
PRIVATE int com_out(cmd)
struct command *cmd;		/* Command block */
{
/* Output the command block to the winchester controller and return status */

  struct wini *wn = w_wn;
  unsigned base_cmd = wn->base_cmd;
  unsigned base_ctl = wn->base_ctl;
  pvb_pair_t outbyte[7];		/* vector for sys_voutb() */
  int s;				/* status for sys_(v)outb() */

  if (w_wn->state & IGNORING) return ERR;

  if (!w_waitfor(STATUS_BSY, 0)) {
	printf("%s: controller not ready\n", w_name());
	return(ERR);
  }

  /* Select drive. */
  if ((s=sys_outb(base_cmd + REG_LDH, cmd->ldh)) != OK)
  	panic(w_name(),"Couldn't write register to select drive",s);

  if (!w_waitfor(STATUS_BSY, 0)) {
	printf("%s: com_out: drive not ready\n", w_name());
	return(ERR);
  }

  /* Schedule a wakeup call, some controllers are flaky. This is done with
   * a synchronous alarm. If a timeout occurs a SYN_ALARM message is sent
   * from HARDWARE, so that w_intr_wait() can call w_timeout() in case the
   * controller was not able to execute the command. Leftover timeouts are
   * simply ignored by the main loop. 
   */
  sys_setalarm(wakeup_ticks, 0);

  wn->w_status = STATUS_ADMBSY;
  w_command = cmd->command;
  pv_set(outbyte[0], base_ctl + REG_CTL, wn->pheads >= 8 ? CTL_EIGHTHEADS : 0);
  pv_set(outbyte[1], base_cmd + REG_PRECOMP, cmd->precomp);
  pv_set(outbyte[2], base_cmd + REG_COUNT, cmd->count);
  pv_set(outbyte[3], base_cmd + REG_SECTOR, cmd->sector);
  pv_set(outbyte[4], base_cmd + REG_CYL_LO, cmd->cyl_lo);
  pv_set(outbyte[5], base_cmd + REG_CYL_HI, cmd->cyl_hi);
  pv_set(outbyte[6], base_cmd + REG_COMMAND, cmd->command);
  if ((s=sys_voutb(outbyte,7)) != OK)
  	panic(w_name(),"Couldn't write registers with sys_voutb()",s);
  return(OK);
}

/*===========================================================================*
 *				com_out_ext				     *
 *===========================================================================*/
PRIVATE int com_out_ext(cmd)
struct command *cmd;		/* Command block */
{
/* Output the command block to the winchester controller and return status */

  struct wini *wn = w_wn;
  unsigned base_cmd = wn->base_cmd;
  unsigned base_ctl = wn->base_ctl;
  pvb_pair_t outbyte[11];		/* vector for sys_voutb() */
  int s;				/* status for sys_(v)outb() */
  unsigned long w_status;

  if (w_wn->state & IGNORING) return ERR;

  if (!w_waitfor(STATUS_BSY, 0)) {
	printf("%s: controller not ready\n", w_name());
	return(ERR);
  }

  /* Select drive. */
  if ((s=sys_outb(base_cmd + REG_LDH, cmd->ldh)) != OK)
  	panic(w_name(),"Couldn't write register to select drive",s);

  if (!w_waitfor(STATUS_BSY, 0)) {
	printf("%s: com_out: drive not ready\n", w_name());
	return(ERR);
  }

  /* Schedule a wakeup call, some controllers are flaky. This is done with
   * a synchronous alarm. If a timeout occurs a SYN_ALARM message is sent
   * from HARDWARE, so that w_intr_wait() can call w_timeout() in case the
   * controller was not able to execute the command. Leftover timeouts are
   * simply ignored by the main loop. 
   */
  sys_setalarm(wakeup_ticks, 0);

  wn->w_status = STATUS_ADMBSY;
  w_command = cmd->command;
  pv_set(outbyte[0], base_ctl + REG_CTL, 0);
  pv_set(outbyte[1], base_cmd + REG_COUNT, cmd->count_prev);
  pv_set(outbyte[2], base_cmd + REG_SECTOR, cmd->sector_prev);
  pv_set(outbyte[3], base_cmd + REG_CYL_LO, cmd->cyl_lo_prev);
  pv_set(outbyte[4], base_cmd + REG_CYL_HI, cmd->cyl_hi_prev);
  pv_set(outbyte[5], base_cmd + REG_COUNT, cmd->count);
  pv_set(outbyte[6], base_cmd + REG_SECTOR, cmd->sector);
  pv_set(outbyte[7], base_cmd + REG_CYL_LO, cmd->cyl_lo);
  pv_set(outbyte[8], base_cmd + REG_CYL_HI, cmd->cyl_hi);
  pv_set(outbyte[9], base_cmd + REG_COMMAND, cmd->command);
  if ((s=sys_voutb(outbyte, 10)) != OK)
  	panic(w_name(),"Couldn't write registers with sys_voutb()",s);

  return(OK);
}

/*===========================================================================*
 *				setup_dma				     *
 *===========================================================================*/
PRIVATE void setup_dma(sizep, proc_nr, iov, do_write, do_copyoutp, safe)
unsigned *sizep;
int proc_nr;
iovec_t *iov;
int do_write;
int *do_copyoutp;
int safe;
{
	phys_bytes phys, user_phys;
	unsigned n, offset, size;
	int i, j, r, bad;
	unsigned long v;
	struct wini *wn = w_wn;

	/* First try direct scatter/gather to the supplied buffers */
	size= *sizep;
	i= 0;	/* iov index */
	j= 0;	/* prdt index */
	bad= 0;
	offset= 0;	/* Offset in current iov */

#if 0
	printf("setup_dma: proc_nr %d\n", proc_nr);
#endif

	while (size > 0)
	{
#if 0
		printf(
		"setup_dma: iov[%d]: addr 0x%x, size %d offset %d, size %d\n",
			i, iov[i].iov_addr, iov[i].iov_size, offset, size);
#endif
			
		n= iov[i].iov_size-offset;
		if (n > size)
			n= size;
		if (n == 0 || (n & 1))
			panic("at_wini", "bad size in iov", iov[i].iov_size);
		if(safe) {
		 r= sys_umap(proc_nr, GRANT_SEG, iov[i].iov_addr, n,&user_phys);
		 user_phys += offset;
		} else {
		 r= sys_umap(proc_nr, D, iov[i].iov_addr+offset, n, &user_phys);
		}
		if (r != 0)
			panic("at_wini", "can't map user buffer", r);
		if (user_phys & 1)
		{
			/* Buffer is not aligned */
			printf("setup_dma: user buffer is not aligned\n");
			bad= 1;
			break;
		}

		/* vector is not allowed to cross a 64K boundary */
		if (user_phys/0x10000 != (user_phys+n-1)/0x10000)
			n= ((user_phys/0x10000)+1)*0x10000 - user_phys;

		/* vector is not allowed to be bigger than 64K, but we get that
		 * for free.
		 */

		if (j >= N_PRDTE)
		{
			/* Too many entries */
			bad= 1;
			break;
		}

		prdt[j].prdte_base= user_phys;
		prdt[j].prdte_count= n;
		prdt[j].prdte_reserved= 0;
		prdt[j].prdte_flags= 0;
		j++;

		offset += n;
		if (offset >= iov[i].iov_size)
		{
			i++;
			offset= 0;
		}

		size -= n;
	}

	if (!bad)
	{
		if (j <= 0 || j > N_PRDTE)
			panic("at_wini", "bad prdt index", j);
		prdt[j-1].prdte_flags |= PRDTE_FL_EOT;

#if 0
		for (i= 0; i<j; i++)
		{
			printf("prdt[%d]: base 0x%x, size %d, flags 0x%x\n",
				i, prdt[i].prdte_base, prdt[i].prdte_count,
				prdt[i].prdte_flags);
		}
#endif
	}

	/* The caller needs to perform a copy-out from the dma buffer if
	 * this is a read request and we can't DMA directly to the user's
	 * buffers.
	 */
	*do_copyoutp= (!do_write && bad);

	if (bad)
	{
		/* Adjust request size */
		size= *sizep;
		if (size > ATA_DMA_BUF_SIZE)
			*sizep= size= ATA_DMA_BUF_SIZE;

		if (do_write)
		{
			/* Copy-in */
			for (offset= 0; offset < size; offset += n)
			{
				n= size-offset;
				if (n > iov->iov_size)
					n= iov->iov_size;
			
				if(safe) {
				  r= sys_safecopyfrom(proc_nr, iov->iov_addr,
					0, (vir_bytes)dma_buf+offset, n, D);
				} else {
				  r= sys_vircopy(proc_nr, D, iov->iov_addr,
					SELF, D, (vir_bytes)dma_buf+offset, 
					n);
				}
				if (r != OK)
				{
					panic(w_name(),
					"setup_dma: sys_vircopy failed",
						r);
				}
				iov++;
			}
		}
	
		/* Fill-in the physical region descriptor table */
		phys= dma_buf_phys;
		if (phys & 1)
		{
			/* Two byte alignment is required */
			panic("at_wini", "bad buffer alignment in setup_dma",
				phys);
		}
		for (j= 0; j<N_PRDTE; i++)
		{
			if (size == 0)
			{
				panic("at_wini", "bad size in setup_dma",
					size);
			}
			if (size & 1)
			{
				/* Two byte alignment is required for size */
				panic("at_wini",
					"bad size alignment in setup_dma",
					size);
			}
			n= size;

			/* Buffer is not allowed to cross a 64K boundary */
			if (phys / 0x10000 != (phys+n-1) / 0x10000)
			{
				n= ((phys/0x10000)+1)*0x10000 - phys;
			}
			prdt[j].prdte_base= phys;
			prdt[j].prdte_count= n;
			prdt[j].prdte_reserved= 0;
			prdt[j].prdte_flags= 0;

			size -= n;
			if (size == 0)
			{
				prdt[j].prdte_flags |= PRDTE_FL_EOT;
				break;
			}
		}
		if (size != 0)
			panic("at_wini", "size to large for prdt", NO_NUM);

#if 0
		for (i= 0; i<=j; i++)
		{
			printf("prdt[%d]: base 0x%x, size %d, flags 0x%x\n",
				i, prdt[i].prdte_base, prdt[i].prdte_count,
				prdt[i].prdte_flags);
		}
#endif
	}

	/* Stop bus master operation */
	r= sys_outb(wn->base_dma + DMA_COMMAND, 0);
	if (r != 0) panic("at_wini", "setup_dma: sys_outb failed", r);

	/* Verify that the bus master is not active */
	r= sys_inb(wn->base_dma + DMA_STATUS, &v);
	if (r != 0) panic("at_wini", "setup_dma: sys_inb failed", r);
	if (v & DMA_ST_BM_ACTIVE)
		panic("at_wini", "Bus master IDE active", NO_NUM);

	if (prdt_phys & 3)
		panic("at_wini", "prdt not aligned", prdt_phys);
	r= sys_outl(wn->base_dma + DMA_PRDTP, prdt_phys);
	if (r != 0) panic("at_wini", "setup_dma: sys_outl failed", r);

	/* Clear interrupt and error flags */
	r= sys_outb(wn->base_dma + DMA_STATUS, DMA_ST_INT | DMA_ST_ERROR);
	if (r != 0) panic("at_wini", "setup_dma: sys_outb failed", r);

	/* Assume disk reads. Start DMA */
	v= DMA_CMD_START;
	if (!do_write)
	{
		/* Disk reads generate PCI write cycles. */
		v |= DMA_CMD_WRITE;	
	}
	r= sys_outb(wn->base_dma + DMA_COMMAND, v);
	if (r != 0) panic("at_wini", "setup_dma: sys_outb failed", r);

#if 0
	r= sys_inb(wn->base_dma + DMA_STATUS, &v);
	if (r != 0) panic("at_wini", "setup_dma: sys_inb failed", r);
	printf("dma status: 0x%x\n", v);
#endif
}


/*===========================================================================*
 *				w_need_reset				     *
 *===========================================================================*/
PRIVATE void w_need_reset()
{
/* The controller needs to be reset. */
  struct wini *wn;
  int dr = 0;

  for (wn = wini; wn < &wini[MAX_DRIVES]; wn++, dr++) {
	if (wn->base_cmd == w_wn->base_cmd) {
		wn->state |= DEAF;
		wn->state &= ~INITIALIZED;
	}
  }
}

/*===========================================================================*
 *				w_do_close				     *
 *===========================================================================*/
PRIVATE int w_do_close(dp, m_ptr)
struct driver *dp;
message *m_ptr;
{
/* Device close: Release a device. */
  if (w_prepare(m_ptr->DEVICE) == NIL_DEV)
  	return(ENXIO);
  w_wn->open_ct--;
#if ENABLE_ATAPI
  if (w_wn->open_ct == 0 && (w_wn->state & ATAPI)) atapi_close();
#endif
  return(OK);
}

/*===========================================================================*
 *				com_simple				     *
 *===========================================================================*/
PRIVATE int com_simple(cmd)
struct command *cmd;		/* Command block */
{
/* A simple controller command, only one interrupt and no data-out phase. */
  int r;

  if (w_wn->state & IGNORING) return ERR;

  if ((r = com_out(cmd)) == OK) r = at_intr_wait();
  w_command = CMD_IDLE;
  return(r);
}

/*===========================================================================*
 *				w_timeout				     *
 *===========================================================================*/
PRIVATE void w_timeout(void)
{
  struct wini *wn = w_wn;

  switch (w_command) {
  case CMD_IDLE:
	break;		/* fine */
  case CMD_READ:
  case CMD_READ_EXT:
  case CMD_WRITE:
  case CMD_WRITE_EXT:
	/* Impossible, but not on PC's:  The controller does not respond. */

	/* Limiting multisector I/O seems to help. */
	if (wn->max_count > 8 * SECTOR_SIZE) {
		wn->max_count = 8 * SECTOR_SIZE;
	} else {
		wn->max_count = SECTOR_SIZE;
	}
	/*FALL THROUGH*/
  default:
	/* Some other command. */
	if (w_testing)  wn->state |= IGNORING;	/* Kick out this drive. */
	else if (!w_silent) printf("%s: timeout on command 0x%02x\n",
		w_name(), w_command);
	w_need_reset();
	wn->w_status = 0;
  }
}

/*===========================================================================*
 *				w_reset					     *
 *===========================================================================*/
PRIVATE int w_reset()
{
/* Issue a reset to the controller.  This is done after any catastrophe,
 * like the controller refusing to respond.
 */
  int s;
  struct wini *wn = w_wn;

  /* Don't bother if this drive is forgotten. */
  if (w_wn->state & IGNORING) return ERR;

  /* Wait for any internal drive recovery. */
  tickdelay(RECOVERY_TICKS);

  /* Strobe reset bit */
  if ((s=sys_outb(wn->base_ctl + REG_CTL, CTL_RESET)) != OK)
  	panic(w_name(),"Couldn't strobe reset bit",s);
  tickdelay(DELAY_TICKS);
  if ((s=sys_outb(wn->base_ctl + REG_CTL, 0)) != OK)
  	panic(w_name(),"Couldn't strobe reset bit",s);
  tickdelay(DELAY_TICKS);

  /* Wait for controller ready */
  if (!w_waitfor(STATUS_BSY, 0)) {
	printf("%s: reset failed, drive busy\n", w_name());
	return(ERR);
  }

  /* The error register should be checked now, but some drives mess it up. */

  for (wn = wini; wn < &wini[MAX_DRIVES]; wn++) {
	if (wn->base_cmd == w_wn->base_cmd) {
		wn->state &= ~DEAF;
  		if (w_wn->irq_need_ack) {
		    	/* Make sure irq is actually enabled.. */
	  		sys_irqenable(&w_wn->irq_hook_id);
		}
	}
  }
		

  return(OK);
}

/*===========================================================================*
 *				w_intr_wait				     *
 *===========================================================================*/
PRIVATE void w_intr_wait()
{
/* Wait for a task completion interrupt. */

  int r;
  unsigned long w_status;
  message m;

  if (w_wn->irq != NO_IRQ) {
	/* Wait for an interrupt that sets w_status to "not busy".
	 * (w_timeout() also clears w_status.)
	 */
	while (w_wn->w_status & (STATUS_ADMBSY|STATUS_BSY)) {
		int rr;
		if((rr=receive(ANY, &m)) != OK)
			panic("at_wini", "receive(ANY) failed", rr);
		switch(m.m_type) {
		  case SYN_ALARM:
			/* Timeout. */
			w_timeout();	      /* a.o. set w_status */
			break;
		  case HARD_INT:
			/* Interrupt. */
			r= sys_inb(w_wn->base_cmd + REG_STATUS, &w_status);
			if (r != 0)
				panic("at_wini", "sys_inb failed", r);
			w_wn->w_status= w_status;
			ack_irqs(m.NOTIFY_ARG);
			break;
		  case DEV_PING:
			/* RS monitor ping. */
			notify(m.m_source);
			break;
		  default:
			/* unhandled message.
			 * queue it and handle it in the libdriver loop.
			 */
			mq_queue(&m);
		}
	}
  } else {
	/* Interrupt not yet allocated; use polling. */
	(void) w_waitfor(STATUS_BSY, 0);
  }
}

/*===========================================================================*
 *				at_intr_wait				     *
 *===========================================================================*/
PRIVATE int at_intr_wait()
{
/* Wait for an interrupt, study the status bits and return error/success. */
  int r, s;
  unsigned long inbval;

  w_intr_wait();
  if ((w_wn->w_status & (STATUS_BSY | STATUS_WF | STATUS_ERR)) == 0) {
	r = OK;
  } else {
  	if ((s=sys_inb(w_wn->base_cmd + REG_ERROR, &inbval)) != OK)
  		panic(w_name(),"Couldn't read register",s);
  	if ((w_wn->w_status & STATUS_ERR) && (inbval & ERROR_BB)) {
  		r = ERR_BAD_SECTOR;	/* sector marked bad, retries won't help */
  	} else {
  		r = ERR;		/* any other error */
  	}
  }
  w_wn->w_status |= STATUS_ADMBSY;	/* assume still busy with I/O */
  return(r);
}

/*===========================================================================*
 *				w_waitfor				     *
 *===========================================================================*/
PRIVATE int w_waitfor(mask, value)
int mask;			/* status mask */
int value;			/* required status */
{
/* Wait until controller is in the required state.  Return zero on timeout.
 * An alarm that set a timeout flag is used. TIMEOUT is in micros, we need
 * ticks. Disabling the alarm is not needed, because a static flag is used
 * and a leftover timeout cannot do any harm.
 */
  unsigned long w_status;
  clock_t t0, t1;
  int s;

  getuptime(&t0);
  do {
	if ((s=sys_inb(w_wn->base_cmd + REG_STATUS, &w_status)) != OK)
		panic(w_name(),"Couldn't read register",s);
	w_wn->w_status= w_status;
	if ((w_wn->w_status & mask) == value) {
        	return 1;
	}
  } while ((s=getuptime(&t1)) == OK && (t1-t0) < timeout_ticks );
  if (OK != s) printf("AT_WINI: warning, get_uptime failed: %d\n",s);

  w_need_reset();			/* controller gone deaf */
  return(0);
}

/*===========================================================================*
 *				w_waitfor_dma				     *
 *===========================================================================*/
PRIVATE int w_waitfor_dma(mask, value)
int mask;			/* status mask */
int value;			/* required status */
{
/* Wait until controller is in the required state.  Return zero on timeout.
 * An alarm that set a timeout flag is used. TIMEOUT is in micros, we need
 * ticks. Disabling the alarm is not needed, because a static flag is used
 * and a leftover timeout cannot do any harm.
 */
  unsigned long w_status;
  clock_t t0, t1;
  int s;

  getuptime(&t0);
  do {
	if ((s=sys_inb(w_wn->base_dma + DMA_STATUS, &w_status)) != OK)
		panic(w_name(),"Couldn't read register",s);
	if ((w_status & mask) == value) {
        	return 1;
	}
  } while ((s=getuptime(&t1)) == OK && (t1-t0) < timeout_ticks );
  if (OK != s) printf("AT_WINI: warning, get_uptime failed: %d\n",s);

  return(0);
}

/*===========================================================================*
 *				w_geometry				     *
 *===========================================================================*/
PRIVATE void w_geometry(entry)
struct partition *entry;
{
  struct wini *wn = w_wn;

  if (wn->state & ATAPI) {		/* Make up some numbers. */
	entry->cylinders = div64u(wn->part[0].dv_size, SECTOR_SIZE) / (64*32);
	entry->heads = 64;
	entry->sectors = 32;
  } else {				/* Return logical geometry. */
	entry->cylinders = wn->lcylinders;
	entry->heads = wn->lheads;
	entry->sectors = wn->lsectors;
  }
}

#if ENABLE_ATAPI
/*===========================================================================*
 *				atapi_open				     *
 *===========================================================================*/
PRIVATE int atapi_open()
{
/* Should load and lock the device and obtain its size.  For now just set the
 * size of the device to something big.  What is really needed is a generic
 * SCSI layer that does all this stuff for ATAPI and SCSI devices (kjb). (XXX)
 */
  w_wn->part[0].dv_size = mul64u(800L*1024, 1024);
  return(OK);
}

/*===========================================================================*
 *				atapi_close				     *
 *===========================================================================*/
PRIVATE void atapi_close()
{
/* Should unlock the device.  For now do nothing.  (XXX) */
}

void sense_request(void)
{
	int r, i;
	static u8_t sense[100], packet[ATAPI_PACKETSIZE];

	packet[0] = SCSI_SENSE;
	packet[1] = 0;
	packet[2] = 0;
	packet[3] = 0;
	packet[4] = SENSE_PACKETSIZE;
	packet[5] = 0;
	packet[7] = 0;
	packet[8] = 0;
	packet[9] = 0;
	packet[10] = 0;
	packet[11] = 0;

	for(i = 0; i < SENSE_PACKETSIZE; i++) sense[i] = 0xff;
	r = atapi_sendpacket(packet, SENSE_PACKETSIZE);
	if (r != OK) { printf("request sense command failed\n"); return; }
	if (atapi_intr_wait() <= 0) { printf("WARNING: request response failed\n"); }

	if (sys_insw(w_wn->base_cmd + REG_DATA, SELF, (void *) sense, SENSE_PACKETSIZE) != OK)
		printf("WARNING: sense reading failed\n");

	printf("sense data:");
	for(i = 0; i < SENSE_PACKETSIZE; i++) printf(" %02x", sense[i]);
	printf("\n");
}

/*===========================================================================*
 *				atapi_transfer				     *
 *===========================================================================*/
PRIVATE int atapi_transfer(proc_nr, opcode, position, iov, nr_req, safe)
int proc_nr;			/* process doing the request */
int opcode;			/* DEV_GATHER_S or DEV_SCATTER_S */
u64_t position;			/* offset on device to read or write */
iovec_t *iov;			/* pointer to read or write request vector */
unsigned nr_req;		/* length of request vector */
int safe;			/* use safecopies? */
{
  struct wini *wn = w_wn;
  iovec_t *iop, *iov_end = iov + nr_req;
  int r, s, errors, fresh;
  u64_t pos;
  unsigned long block;
  u64_t dv_size = w_dv->dv_size;
  unsigned nbytes, nblocks, count, before, chunk;
  static u8_t packet[ATAPI_PACKETSIZE];
  size_t addr_offset = 0;

  errors = fresh = 0;

  while (nr_req > 0 && !fresh) {
	/* The Minix block size is smaller than the CD block size, so we
	 * may have to read extra before or after the good data.
	 */
	pos = add64(w_dv->dv_base, position);
	block = div64u(pos, CD_SECTOR_SIZE);
	before = rem64u(pos, CD_SECTOR_SIZE);

	/* How many bytes to transfer? */
	nbytes = count = 0;
	for (iop = iov; iop < iov_end; iop++) {
		nbytes += iop->iov_size;
		if ((before + nbytes) % CD_SECTOR_SIZE == 0) count = nbytes;
	}

	/* Does one of the memory chunks end nicely on a CD sector multiple? */
	if (count != 0) nbytes = count;

	/* Data comes in as words, so we have to enforce even byte counts. */
	if ((before | nbytes) & 1) return(EINVAL);

	/* Which block on disk and how close to EOF? */
	if (cmp64(position, dv_size) >= 0) return(OK);		/* At EOF */
	if (cmp64(add64ul(position, nbytes), dv_size) > 0)
		nbytes = diff64(dv_size, position);

	nblocks = (before + nbytes + CD_SECTOR_SIZE - 1) / CD_SECTOR_SIZE;
	if (ATAPI_DEBUG) {
		printf("block=%lu, before=%u, nbytes=%u, nblocks=%u\n",
			block, before, nbytes, nblocks);
	}

	/* First check to see if a reinitialization is needed. */
	if (!(wn->state & INITIALIZED) && w_specify() != OK) return(EIO);

	/* Build an ATAPI command packet. */
	packet[0] = SCSI_READ10;
	packet[1] = 0;
	packet[2] = (block >> 24) & 0xFF;
	packet[3] = (block >> 16) & 0xFF;
	packet[4] = (block >>  8) & 0xFF;
	packet[5] = (block >>  0) & 0xFF;
	packet[6] = 0;
	packet[7] = (nblocks >> 8) & 0xFF;
	packet[8] = (nblocks >> 0) & 0xFF;
	packet[9] = 0;
	packet[10] = 0;
	packet[11] = 0;

	/* Tell the controller to execute the packet command. */
	r = atapi_sendpacket(packet, nblocks * CD_SECTOR_SIZE);
	if (r != OK) goto err;

	/* Read chunks of data. */
	while ((r = atapi_intr_wait()) > 0) {
		count = r;

		if (ATAPI_DEBUG) {
			printf("before=%u, nbytes=%u, count=%u\n",
				before, nbytes, count);
		}

		while (before > 0 && count > 0) {	/* Discard before. */
			chunk = before;
			if (chunk > count) chunk = count;
			if (chunk > DMA_BUF_SIZE) chunk = DMA_BUF_SIZE;
	if ((s=sys_insw(wn->base_cmd + REG_DATA, SELF, tmp_buf, chunk)) != OK)
		panic(w_name(),"Call to sys_insw() failed", s);
			before -= chunk;
			count -= chunk;
		}

		while (nbytes > 0 && count > 0) {	/* Requested data. */
			chunk = nbytes;
			if (chunk > count) chunk = count;
			if (chunk > iov->iov_size) chunk = iov->iov_size;
			if(safe) {
				s=sys_safe_insw(wn->base_cmd + REG_DATA, proc_nr,
					(void *) iov->iov_addr, addr_offset, chunk);
			} else {
				s=sys_insw(wn->base_cmd + REG_DATA, proc_nr,
					(void *) (iov->iov_addr + addr_offset), chunk);
			}
			if (s != OK)
				panic(w_name(),"Call to sys_insw() failed", s);
			position= add64ul(position, chunk);
			nbytes -= chunk;
			count -= chunk;
			addr_offset += chunk;
			fresh = 0;
			if ((iov->iov_size -= chunk) == 0) {
				iov++;
				nr_req--;
				fresh = 1;	/* new element is optional */
				addr_offset = 0;
			}
		}

		while (count > 0) {		/* Excess data. */
			chunk = count;
			if (chunk > DMA_BUF_SIZE) chunk = DMA_BUF_SIZE;
	if ((s=sys_insw(wn->base_cmd + REG_DATA, SELF, tmp_buf, chunk)) != OK)
		panic(w_name(),"Call to sys_insw() failed", s);
			count -= chunk;
		}
	}

	if (r < 0) {
  err:		/* Don't retry if too many errors. */
		if (atapi_debug) sense_request();
		if (++errors == max_errors) {
			w_command = CMD_IDLE;
			if (atapi_debug) printf("giving up (%d)\n", errors);
			return(EIO);
		}
		if (atapi_debug) printf("retry (%d)\n", errors);
	}
  }

  w_command = CMD_IDLE;
  return(OK);
}

/*===========================================================================*
 *				atapi_sendpacket			     *
 *===========================================================================*/
PRIVATE int atapi_sendpacket(packet, cnt)
u8_t *packet;
unsigned cnt;
{
/* Send an Atapi Packet Command */
  struct wini *wn = w_wn;
  pvb_pair_t outbyte[6];		/* vector for sys_voutb() */
  int s;

  if (wn->state & IGNORING) return ERR;

  /* Select Master/Slave drive */
  if ((s=sys_outb(wn->base_cmd + REG_DRIVE, wn->ldhpref)) != OK)
  	panic(w_name(),"Couldn't select master/ slave drive",s);

  if (!w_waitfor(STATUS_BSY | STATUS_DRQ, 0)) {
	printf("%s: atapi_sendpacket: drive not ready\n", w_name());
	return(ERR);
  }

  /* Schedule a wakeup call, some controllers are flaky. This is done with
   * a synchronous alarm. If a timeout occurs a SYN_ALARM message is sent
   * from HARDWARE, so that w_intr_wait() can call w_timeout() in case the
   * controller was not able to execute the command. Leftover timeouts are
   * simply ignored by the main loop. 
   */
  sys_setalarm(wakeup_ticks, 0);

#if _WORD_SIZE > 2
  if (cnt > 0xFFFE) cnt = 0xFFFE;	/* Max data per interrupt. */
#endif

  w_command = ATAPI_PACKETCMD;
  pv_set(outbyte[0], wn->base_cmd + REG_FEAT, 0);
  pv_set(outbyte[1], wn->base_cmd + REG_IRR, 0);
  pv_set(outbyte[2], wn->base_cmd + REG_SAMTAG, 0);
  pv_set(outbyte[3], wn->base_cmd + REG_CNT_LO, (cnt >> 0) & 0xFF);
  pv_set(outbyte[4], wn->base_cmd + REG_CNT_HI, (cnt >> 8) & 0xFF);
  pv_set(outbyte[5], wn->base_cmd + REG_COMMAND, w_command);
  if (atapi_debug) printf("cmd: %x  ", w_command);
  if ((s=sys_voutb(outbyte,6)) != OK)
  	panic(w_name(),"Couldn't write registers with sys_voutb()",s);

  if (!w_waitfor(STATUS_BSY | STATUS_DRQ, STATUS_DRQ)) {
	printf("%s: timeout (BSY|DRQ -> DRQ)\n", w_name());
	return(ERR);
  }
  wn->w_status |= STATUS_ADMBSY;		/* Command not at all done yet. */

  /* Send the command packet to the device. */
  if ((s=sys_outsw(wn->base_cmd + REG_DATA, SELF, packet, ATAPI_PACKETSIZE)) != OK)
	panic(w_name(),"sys_outsw() failed", s);

 {
 int p;
 if (atapi_debug) {
 	printf("sent command:");
	 for(p = 0; p < ATAPI_PACKETSIZE; p++) { printf(" %02x", packet[p]); }
	 printf("\n");
	}
 }
  return(OK);
}


#endif /* ENABLE_ATAPI */

/*===========================================================================*
 *				w_other					     *
 *===========================================================================*/
PRIVATE int w_other(dr, m, safe)
struct driver *dr;
message *m;
int safe;
{
	int r, timeout, prev;

	if (m->m_type != DEV_IOCTL_S )
		return EINVAL;

	if (m->REQUEST == DIOCTIMEOUT) {
		if(safe) {
		  r= sys_safecopyfrom(m->IO_ENDPT, (vir_bytes) m->IO_GRANT,
			0, (vir_bytes)&timeout, sizeof(timeout), D);
		} else {
		  r= sys_datacopy(m->IO_ENDPT, (vir_bytes)m->ADDRESS,
			SELF, (vir_bytes)&timeout, sizeof(timeout));
		}

		if(r != OK)
		    return r;
	
		if (timeout == 0) {
			/* Restore defaults. */
			timeout_ticks = DEF_TIMEOUT_TICKS;
			max_errors = MAX_ERRORS;
			wakeup_ticks = WAKEUP_TICKS;
			w_silent = 0;
		} else if (timeout < 0) {
			return EINVAL;
		} else  {
			prev = wakeup_ticks;
	
			if (!w_standard_timeouts) {
				/* Set (lower) timeout, lower error
				 * tolerance and set silent mode.
				 */
				wakeup_ticks = timeout;
				max_errors = 3;
				w_silent = 1;
	
				if (timeout_ticks > timeout)
					timeout_ticks = timeout;
			}
	
			if(safe) {
		  	   r= sys_safecopyto(m->IO_ENDPT,
				(vir_bytes) m->IO_GRANT,
				0, (vir_bytes)&prev, sizeof(prev), D);
			} else {
			   r=sys_datacopy(SELF, (vir_bytes)&prev, 
				m->IO_ENDPT, (vir_bytes)m->ADDRESS,
				sizeof(prev));
			}

			if(r != OK)
				return r;
		}
	
		return OK;
	} else  if (m->REQUEST == DIOCOPENCT) {
		int count;
		if (w_prepare(m->DEVICE) == NIL_DEV) return ENXIO;
		count = w_wn->open_ct;
		if(safe) {
		    r= sys_safecopyto(m->IO_ENDPT, (vir_bytes) m->IO_GRANT,
			0, (vir_bytes)&count, sizeof(count), D);
		} else {
		    r=sys_datacopy(SELF, (vir_bytes)&count, 
			m->IO_ENDPT, (vir_bytes)m->ADDRESS, sizeof(count));
		} 

		if(r != OK)
			return r;

		return OK;
	}
	return EINVAL;
}

/*===========================================================================*
 *				w_hw_int				     *
 *===========================================================================*/
PRIVATE int w_hw_int(dr, m)
struct driver *dr;
message *m;
{
  /* Leftover interrupt(s) received; ack it/them. */
  ack_irqs(m->NOTIFY_ARG);

  return OK;
}


/*===========================================================================*
 *				ack_irqs				     *
 *===========================================================================*/
PRIVATE void ack_irqs(unsigned int irqs)
{
  unsigned int drive;
  unsigned long w_status;

  for (drive = 0; drive < MAX_DRIVES && irqs; drive++) {
  	if (!(wini[drive].state & IGNORING) && wini[drive].irq_need_ack &&
		(wini[drive].irq_mask & irqs)) {
		if (sys_inb((wini[drive].base_cmd + REG_STATUS),
			&w_status) != OK)
		{
		  	panic(w_name(), "couldn't ack irq on drive %d\n",
				drive);
		}
		wini[drive].w_status= w_status;
	 	if (sys_irqenable(&wini[drive].irq_hook_id) != OK)
		  	printf("couldn't re-enable drive %d\n", drive);
		irqs &= ~wini[drive].irq_mask;
	}
  }
}


#define STSTR(a) if (status & STATUS_ ## a) { strcat(str, #a); strcat(str, " "); }
#define ERRSTR(a) if (e & ERROR_ ## a) { strcat(str, #a); strcat(str, " "); }
char *strstatus(int status)
{
	static char str[200];
	str[0] = '\0';

	STSTR(BSY);
	STSTR(DRDY);
	STSTR(DMADF);
	STSTR(SRVCDSC);
	STSTR(DRQ);
	STSTR(CORR);
	STSTR(CHECK);
	return str;
}

char *strerr(int e)
{
	static char str[200];
	str[0] = '\0';

	ERRSTR(BB);
	ERRSTR(ECC);
	ERRSTR(ID);
	ERRSTR(AC);
	ERRSTR(TK);
	ERRSTR(DM);

	return str;
}

#if ENABLE_ATAPI

/*===========================================================================*
 *				atapi_intr_wait				     *
 *===========================================================================*/
PRIVATE int atapi_intr_wait()
{
/* Wait for an interrupt and study the results.  Returns a number of bytes
 * that need to be transferred, or an error code.
 */
  struct wini *wn = w_wn;
  pvb_pair_t inbyte[4];		/* vector for sys_vinb() */
  int s;			/* status for sys_vinb() */
  int e;
  int len;
  int irr;
  int r;
  int phase;

  w_intr_wait();

  /* Request series of device I/O. */
  inbyte[0].port = wn->base_cmd + REG_ERROR;
  inbyte[1].port = wn->base_cmd + REG_CNT_LO;
  inbyte[2].port = wn->base_cmd + REG_CNT_HI;
  inbyte[3].port = wn->base_cmd + REG_IRR;
  if ((s=sys_vinb(inbyte, 4)) != OK)
  	panic(w_name(),"ATAPI failed sys_vinb()", s);
  e = inbyte[0].value;
  len = inbyte[1].value;
  len |= inbyte[2].value << 8;
  irr = inbyte[3].value;

#if ATAPI_DEBUG
	printf("wn %p  S=%x=%s E=%02x=%s L=%04x I=%02x\n", wn, wn->w_status, strstatus(wn->w_status), e, strerr(e), len, irr);
#endif
  if (wn->w_status & (STATUS_BSY | STATUS_CHECK)) {
	if (atapi_debug) {
		printf("atapi fail:  S=%x=%s E=%02x=%s L=%04x I=%02x\n", wn->w_status, strstatus(wn->w_status), e, strerr(e), len, irr);
	}
  	return ERR;
  }

  phase = (wn->w_status & STATUS_DRQ) | (irr & (IRR_COD | IRR_IO));

  switch (phase) {
  case IRR_COD | IRR_IO:
	if (ATAPI_DEBUG) printf("ACD: Phase Command Complete\n");
	r = OK;
	break;
  case 0:
	if (ATAPI_DEBUG) printf("ACD: Phase Command Aborted\n");
	r = ERR;
	break;
  case STATUS_DRQ | IRR_COD:
	if (ATAPI_DEBUG) printf("ACD: Phase Command Out\n");
	r = ERR;
	break;
  case STATUS_DRQ:
	if (ATAPI_DEBUG) printf("ACD: Phase Data Out %d\n", len);
	r = len;
	break;
  case STATUS_DRQ | IRR_IO:
	if (ATAPI_DEBUG) printf("ACD: Phase Data In %d\n", len);
	r = len;
	break;
  default:
	if (ATAPI_DEBUG) printf("ACD: Phase Unknown\n");
	r = ERR;
	break;
  }

#if 0
  /* retry if the media changed */
  XXX while (phase == (IRR_IO | IRR_COD) && (wn->w_status & STATUS_CHECK)
	&& (e & ERROR_SENSE) == SENSE_UATTN && --try > 0);
#endif

  wn->w_status |= STATUS_ADMBSY;	/* Assume not done yet. */
  return(r);
}

#endif /* ENABLE_ATAPI */

#undef sys_voutb
#undef sys_vinb

PRIVATE int at_voutb(int line, pvb_pair_t *pvb, int n)
{
  int s, i;
  if ((s=sys_voutb(pvb,n)) == OK)
	return OK;
  printf("at_wini%d: sys_voutb failed: %d pvb (%d):\n", w_instance, s, n);
  for(i = 0; i < n; i++)
	printf("%2d: %4x -> %4x\n", i, pvb[i].value, pvb[i].port);
  panic(w_name(), "sys_voutb failed", NO_NUM);
}

PRIVATE int at_vinb(int line, pvb_pair_t *pvb, int n)
{
  int s, i;
  if ((s=sys_vinb(pvb,n)) == OK)
	return OK;
  printf("at_wini%d: sys_vinb failed: %d pvb (%d):\n", w_instance, s, n);
  for(i = 0; i < n; i++)
	printf("%2d: %4x\n", i, pvb[i].port);
  panic(w_name(), "sys_vinb failed", NO_NUM);
}

PRIVATE int at_out(int line, u32_t port, u32_t value,
	char *typename, int type)
{
	int s;
	s = sys_out(port, value, type);
	if(s == OK)
		return OK;
	printf("at_wini%d: line %d: %s failed: %d; %x -> %x\n", 
		w_instance, line, typename, s, value, port);
        panic(w_name(), "sys_out failed", NO_NUM);
}


PRIVATE int at_in(int line, u32_t port, u32_t *value,
	char *typename, int type)
{
	int s;
	s = sys_in(port, value, type);
	if(s == OK)
		return OK;
	printf("at_wini%d: line %d: %s failed: %d; port %x\n", 
		w_instance, line, typename, s, value, port);
        panic(w_name(), "sys_out failed", NO_NUM);
}

#undef panic
PRIVATE void at_panic(line, h, msg, n)
int line;
char *h;
char *msg;
int n;
{
	printf("at_wini%d: panic at line %d: %s: %s %d\n",
		w_instance, line, h, msg, n);
	while(1);
}