minix/drivers/dpeth/dp.c

617 lines
15 KiB
C
Raw Normal View History

/*
** File: dp.c Version 1.01, Oct. 17, 2007
** Original: eth.c Version 1.00, Jan. 14, 1997
**
** Author: Giovanni Falzoni <gfalzoni@inwind.it>
**
** This file contains the ethernet device driver main task.
** It has to be integrated with the board specific drivers.
** It is a rewriting of Minix 2.0.0 ethernet driver (dp8390.c)
** to remove bord specific code. It should operate (I hope)
** with any board driver.
*/
#include <minix/drivers.h>
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
#include <minix/netdriver.h>
#include <minix/endpoint.h>
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
#include <minix/ds.h>
#include <net/gen/ether.h>
#include <net/gen/eth_io.h>
#include "dp.h"
/*
** Local data
*/
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
static dpeth_t de_state;
static int de_instance;
typedef struct dp_conf { /* Configuration description structure */
port_t dpc_port;
int dpc_irq;
phys_bytes dpc_mem;
} dp_conf_t;
/* Device default configuration */
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
#define DP_CONF_NR 3
static dp_conf_t dp_conf[DP_CONF_NR] = {
/* I/O port, IRQ, Buff addr, Env. var */
{ 0x300, 5, 0xC8000, },
{ 0x280, 10, 0xCC000, },
{ 0x000, 0, 0x00000, },
};
2006-07-10 14:43:38 +02:00
static char CopyErrMsg[] = "unable to read/write user data";
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
static char RecvErrMsg[] = "netdriver_receive failed";
2006-07-10 14:43:38 +02:00
static char SendErrMsg[] = "send failed";
static char SizeErrMsg[] = "illegal packet size";
static char TypeErrMsg[] = "illegal message type";
static char DevName[] = "eth#?";
/*
** Name: void reply(dpeth_t *dep, int err, int m_type)
** Function: Fills a reply message and sends it.
*/
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
static void reply(dpeth_t * dep)
{
message reply;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
int r, flags;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
flags = DL_NOFLAGS;
if (dep->de_flags & DEF_ACK_SEND) flags |= DL_PACK_SEND;
if (dep->de_flags & DEF_ACK_RECV) flags |= DL_PACK_RECV;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
reply.m_type = DL_TASK_REPLY;
reply.DL_FLAGS = flags;
reply.DL_COUNT = dep->de_read_s;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
DEBUG(printf("\t reply %d (%lx)\n", reply.m_type, reply.DL_FLAGS));
if ((r = ipc_send(dep->de_client, &reply)) != OK)
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
panic(SendErrMsg, r);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
dep->de_read_s = 0;
dep->de_flags &= NOT(DEF_ACK_SEND | DEF_ACK_RECV);
return;
}
/*
** Name: void dp_confaddr(dpeth_t *dep)
** Function: Checks environment for a User defined ethernet address.
*/
static void dp_confaddr(dpeth_t * dep)
{
static char ea_fmt[] = "x:x:x:x:x:x";
char ea_key[16];
int ix;
long val;
2012-08-03 17:48:54 +02:00
strlcpy(ea_key, "DPETH0_EA", sizeof(ea_key));
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
ea_key[5] += de_instance;
for (ix = 0; ix < SA_ADDR_LEN; ix++) {
val = dep->de_address.ea_addr[ix];
if (env_parse(ea_key, ea_fmt, ix, &val, 0x00L, 0xFFL) != EP_SET)
break;
dep->de_address.ea_addr[ix] = val;
}
if (ix != 0 && ix != SA_ADDR_LEN)
/* It's all or nothing, force a panic */
env_parse(ea_key, "?", 0, &val, 0L, 0L);
return;
}
/*
** Name: void update_conf(dpeth_t *dep, dp_conf_t *dcp)
** Function: Gets the default settings from 'dp_conf' table and
** modifies them from the environment.
*/
static void update_conf(dpeth_t * dep, const dp_conf_t * dcp)
{
static char dpc_fmt[] = "x:d:x";
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
char ec_key[16];
long val;
2012-08-03 17:48:54 +02:00
strlcpy(ec_key, "DPETH0", sizeof(ec_key));
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
ec_key[5] += de_instance;
dep->de_mode = DEM_SINK;
val = dcp->dpc_port; /* Get I/O port address */
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
switch (env_parse(ec_key, dpc_fmt, 0, &val, 0x000L, 0x3FFL)) {
case EP_OFF: dep->de_mode = DEM_DISABLED; break;
case EP_ON:
case EP_SET: dep->de_mode = DEM_ENABLED; break;
}
dep->de_base_port = val;
val = dcp->dpc_irq | DEI_DEFAULT; /* Get Interrupt line (IRQ) */
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
env_parse(ec_key, dpc_fmt, 1, &val, 0L, (long) NR_IRQ_VECTORS - 1);
dep->de_irq = val;
val = dcp->dpc_mem; /* Get shared memory address */
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
env_parse(ec_key, dpc_fmt, 2, &val, 0L, LONG_MAX);
dep->de_linmem = val;
return;
}
/*
** Name: void do_dump(message *mp)
** Function: Displays statistics on screen (SFx key from console)
*/
static void do_dump(const message *mp)
{
dpeth_t *dep;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
dep = &de_state;
printf("\n\n");
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
if (dep->de_mode == DEM_DISABLED) return;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
printf("%s statistics:\t\t", dep->de_name);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
/* Network interface status */
printf("Status: 0x%04x (%d)\n\n", dep->de_flags, dep->de_int_pending);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
(*dep->de_dumpstatsf) (dep);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
/* Transmitted/received bytes */
printf("Tx bytes:%10ld\t", dep->bytes_Tx);
printf("Rx bytes:%10ld\n", dep->bytes_Rx);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
/* Transmitted/received packets */
printf("Tx OK: %8ld\t", dep->de_stat.ets_packetT);
printf("Rx OK: %8ld\n", dep->de_stat.ets_packetR);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
/* Transmit/receive errors */
printf("Tx Err: %8ld\t", dep->de_stat.ets_sendErr);
printf("Rx Err: %8ld\n", dep->de_stat.ets_recvErr);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
/* Transmit unnerruns/receive overrruns */
printf("Tx Und: %8ld\t", dep->de_stat.ets_fifoUnder);
printf("Rx Ovr: %8ld\n", dep->de_stat.ets_fifoOver);
/* Transmit collisions/receive CRC errors */
printf("Tx Coll: %8ld\t", dep->de_stat.ets_collision);
printf("Rx CRC: %8ld\n", dep->de_stat.ets_CRCerr);
return;
}
/*
2006-07-10 14:43:38 +02:00
** Name: void get_userdata_s(int user_proc, vir_bytes user_addr, int count, void *loc_addr)
** Function: Copies data from user area.
*/
2006-07-10 14:43:38 +02:00
static void get_userdata_s(int user_proc, cp_grant_id_t grant,
vir_bytes offset, int count, void *loc_addr)
{
int rc;
vir_bytes len;
len = (count > IOVEC_NR ? IOVEC_NR : count) * sizeof(iovec_t);
if ((rc = sys_safecopyfrom(user_proc, grant, 0, (vir_bytes)loc_addr, len)) != OK)
panic(CopyErrMsg, rc);
return;
}
/*
** Name: void do_first_init(dpeth_t *dep, dp_conf_t *dcp);
** Function: Init action to setup task
*/
static void do_first_init(dpeth_t *dep, const dp_conf_t *dcp)
{
dep->de_linmem = 0xFFFF0000;
/* Make sure statisics are cleared */
memset((void *) &(dep->de_stat), 0, sizeof(eth_stat_t));
/* Device specific initialization */
(*dep->de_initf) (dep);
/* Set the interrupt handler policy. Request interrupts not to be reenabled
* automatically. Return the IRQ line number when an interrupt occurs.
*/
dep->de_hook = dep->de_irq;
2012-08-03 17:48:54 +02:00
if (sys_irqsetpolicy(dep->de_irq, 0 /*IRQ_REENABLE*/, &dep->de_hook) != OK)
panic("unable to set IRQ policy");
dep->de_int_pending = FALSE;
sys_irqenable(&dep->de_hook);
return;
}
/*
** Name: void do_init(message *mp)
** Function: Checks for hardware presence.
** Provides initialization of hardware and data structures
*/
static void do_init(const message * mp)
{
dpeth_t *dep;
dp_conf_t *dcp;
message reply_mess;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
int r, confnr;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
dep = &de_state;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
/* Pick a default configuration for this instance. */
confnr = MIN(de_instance, DP_CONF_NR-1);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
dcp = &dp_conf[confnr];
2012-08-03 17:48:54 +02:00
strlcpy(dep->de_name, DevName, sizeof(dep->de_name));
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
dep->de_name[4] = '0' + de_instance;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
if (dep->de_mode == DEM_DISABLED) {
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
update_conf(dep, dcp); /* First time thru */
if (dep->de_mode == DEM_ENABLED &&
!el1_probe(dep) && /* Probe for 3c501 */
!wdeth_probe(dep) && /* Probe for WD80x3 */
!ne_probe(dep) && /* Probe for NEx000 */
!el2_probe(dep) && /* Probe for 3c503 */
!el3_probe(dep)) { /* Probe for 3c509 */
printf("%s: warning no ethernet card found at 0x%04X\n",
dep->de_name, dep->de_base_port);
dep->de_mode = DEM_DISABLED;
}
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
}
r = OK;
/* 'de_mode' may change if probe routines fail, test again */
switch (dep->de_mode) {
case DEM_DISABLED:
/* Device is configured OFF or hardware probe failed */
r = ENXIO;
break;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
case DEM_ENABLED:
/* Device is present and probed */
if (dep->de_flags == DEF_EMPTY) {
/* These actions only the first time */
do_first_init(dep, dcp);
dep->de_flags |= DEF_ENABLED;
}
dep->de_flags &= NOT(DEF_PROMISC | DEF_MULTI | DEF_BROAD);
if (mp->DL_MODE & DL_PROMISC_REQ)
dep->de_flags |= DEF_PROMISC | DEF_MULTI | DEF_BROAD;
if (mp->DL_MODE & DL_MULTI_REQ) dep->de_flags |= DEF_MULTI;
if (mp->DL_MODE & DL_BROAD_REQ) dep->de_flags |= DEF_BROAD;
(*dep->de_flagsf) (dep);
break;
case DEM_SINK:
/* Device not present (sink mode) */
memset(dep->de_address.ea_addr, 0, sizeof(ether_addr_t));
dp_confaddr(dep); /* Station address from env. */
break;
default: break;
2010-01-26 11:59:01 +01:00
}
2006-07-10 14:43:38 +02:00
reply_mess.m_type = DL_CONF_REPLY;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
reply_mess.DL_STAT = r;
if (r == OK)
*(ether_addr_t *) reply_mess.DL_HWADDR = dep->de_address;
DEBUG(printf("\t reply %d\n", reply_mess.m_type));
if (ipc_send(mp->m_source, &reply_mess) != OK) /* Can't send */
panic(SendErrMsg, mp->m_source);
return;
}
/*
** Name: void dp_next_iovec(iovec_dat_t *iovp)
** Function: Retrieves data from next iovec element.
*/
2012-03-25 20:25:53 +02:00
void dp_next_iovec(iovec_dat_s_t * iovp)
{
iovp->iod_iovec_s -= IOVEC_NR;
2006-07-10 14:43:38 +02:00
iovp->iod_iovec_offset += IOVEC_NR * sizeof(iovec_t);
get_userdata_s(iovp->iod_proc_nr, iovp->iod_grant, iovp->iod_iovec_offset,
iovp->iod_iovec_s, iovp->iod_iovec);
return;
}
/*
** Name: int calc_iovec_size(iovec_dat_t *iovp)
** Function: Compute the size of a request.
*/
2006-07-10 14:43:38 +02:00
static int calc_iovec_size(iovec_dat_s_t * iovp)
{
int size, ix;
size = ix = 0;
do {
size += iovp->iod_iovec[ix].iov_size;
if (++ix >= IOVEC_NR) {
dp_next_iovec(iovp);
ix = 0;
}
/* Till all vectors added */
} while (ix < iovp->iod_iovec_s);
return size;
}
/*
** Name: void do_vwrite_s(message *mp)
** Function:
*/
static void do_vwrite_s(const message * mp)
{
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
int size;
dpeth_t *dep;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
dep = &de_state;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
dep->de_client = mp->m_source;
if (dep->de_mode == DEM_ENABLED) {
if (dep->de_flags & DEF_SENDING) /* Is sending in progress? */
panic("send already in progress ");
dep->de_write_iovec.iod_proc_nr = mp->m_source;
get_userdata_s(mp->m_source, mp->DL_GRANT, 0,
2006-07-10 14:43:38 +02:00
mp->DL_COUNT, dep->de_write_iovec.iod_iovec);
dep->de_write_iovec.iod_iovec_s = mp->DL_COUNT;
dep->de_write_iovec.iod_grant = (cp_grant_id_t) mp->DL_GRANT;
2006-07-10 14:43:38 +02:00
dep->de_write_iovec.iod_iovec_offset = 0;
size = calc_iovec_size(&dep->de_write_iovec);
if (size < ETH_MIN_PACK_SIZE || size > ETH_MAX_PACK_SIZE)
panic(SizeErrMsg, size);
dep->de_flags |= DEF_SENDING;
(*dep->de_sendf) (dep, FALSE, size);
} else if (dep->de_mode == DEM_SINK)
dep->de_flags |= DEF_ACK_SEND;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
reply(dep);
return;
}
/*
2006-07-10 14:43:38 +02:00
** Name: void do_vread_s(message *mp, int vectored)
** Function:
*/
static void do_vread_s(const message * mp)
{
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
int size;
dpeth_t *dep;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
dep = &de_state;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
dep->de_client = mp->m_source;
if (dep->de_mode == DEM_ENABLED) {
if (dep->de_flags & DEF_READING) /* Reading in progress */
panic("read already in progress");
dep->de_read_iovec.iod_proc_nr = mp->m_source;
get_userdata_s(mp->m_source, (cp_grant_id_t) mp->DL_GRANT, 0,
2006-07-10 14:43:38 +02:00
mp->DL_COUNT, dep->de_read_iovec.iod_iovec);
dep->de_read_iovec.iod_iovec_s = mp->DL_COUNT;
dep->de_read_iovec.iod_grant = (cp_grant_id_t) mp->DL_GRANT;
2006-07-10 14:43:38 +02:00
dep->de_read_iovec.iod_iovec_offset = 0;
size = calc_iovec_size(&dep->de_read_iovec);
if (size < ETH_MAX_PACK_SIZE) panic(SizeErrMsg, size);
dep->de_flags |= DEF_READING;
(*dep->de_recvf) (dep, FALSE, size);
#if 0
if ((dep->de_flags & (DEF_READING | DEF_STOPPED)) == (DEF_READING | DEF_STOPPED))
/* The chip is stopped, and all arrived packets delivered */
(*dep->de_resetf) (dep);
dep->de_flags &= NOT(DEF_STOPPED);
#endif
}
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
reply(dep);
return;
}
/*
2006-07-10 14:43:38 +02:00
** Name: void do_getstat_s(message *mp)
** Function: Reports device statistics.
*/
static void do_getstat_s(const message * mp)
{
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
int rc;
dpeth_t *dep;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
message reply_mess;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
dep = &de_state;
if (dep->de_mode == DEM_ENABLED) (*dep->de_getstatsf) (dep);
if ((rc = sys_safecopyto(mp->m_source, mp->DL_GRANT, 0,
2006-07-10 14:43:38 +02:00
(vir_bytes)&dep->de_stat,
(vir_bytes) sizeof(dep->de_stat))) != OK)
panic(CopyErrMsg, rc);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
reply_mess.m_type = DL_STAT_REPLY;
rc= ipc_send(mp->m_source, &reply_mess);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
if (rc != OK)
panic("do_getname: ipc_send failed: %d", rc);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
return;
2005-10-21 19:09:08 +02:00
}
/*
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
** Name: void dp_stop(dpeth_t *dep)
** Function: Stops network interface.
*/
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
static void dp_stop(dpeth_t * dep)
{
if (dep->de_mode == DEM_ENABLED && (dep->de_flags & DEF_ENABLED)) {
/* Stop device */
(dep->de_stopf) (dep);
dep->de_flags = DEF_EMPTY;
dep->de_mode = DEM_DISABLED;
}
return;
}
static void do_watchdog(const void *UNUSED(message))
{
DEBUG(printf("\t no reply"));
return;
}
2012-03-25 20:25:53 +02:00
static void handle_hw_intr(void)
{
dpeth_t *dep;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
dep = &de_state;
/* If device is enabled and interrupt pending */
if (dep->de_mode == DEM_ENABLED) {
dep->de_int_pending = TRUE;
(*dep->de_interruptf) (dep);
if (dep->de_flags & (DEF_ACK_SEND | DEF_ACK_RECV))
reply(dep);
dep->de_int_pending = FALSE;
sys_irqenable(&dep->de_hook);
}
}
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
/* SEF functions and variables. */
2012-03-25 20:25:53 +02:00
static void sef_local_startup(void);
static int sef_cb_init_fresh(int type, sef_init_info_t *info);
static void sef_cb_signal_handler(int signo);
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
/*
** Name: int dpeth_task(void)
** Function: Main entry for dp task
*/
2012-03-25 20:25:53 +02:00
int main(int argc, char **argv)
{
message m;
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
int ipc_status;
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
int rc;
2005-10-21 19:09:08 +02:00
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
/* SEF local startup. */
env_setargs(argc, argv);
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
sef_local_startup();
2005-10-21 19:09:08 +02:00
while (TRUE) {
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
if ((rc = netdriver_receive(ANY, &m, &ipc_status)) != OK){
panic(RecvErrMsg, rc);
}
DEBUG(printf("eth: got message %d, ", m.m_type));
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
if (is_ipc_notify(ipc_status)) {
switch(_ENDPOINT_P(m.m_source)) {
case CLOCK:
/* to be defined */
do_watchdog(&m);
break;
case HARDWARE:
/* Interrupt from device */
handle_hw_intr();
break;
case TTY_PROC_NR:
/* Function key pressed */
do_dump(&m);
break;
default:
/* Invalid message type */
panic(TypeErrMsg, m.m_type);
break;
}
/* message processed, get another one */
continue;
}
switch (m.m_type) {
2006-07-10 14:43:38 +02:00
case DL_WRITEV_S: /* Write message to device */
do_vwrite_s(&m);
break;
2006-07-10 14:43:38 +02:00
case DL_READV_S: /* Read message from device */
do_vread_s(&m);
break;
2006-07-10 14:43:38 +02:00
case DL_CONF: /* Initialize device */
do_init(&m);
break;
2006-07-10 14:43:38 +02:00
case DL_GETSTAT_S: /* Get device statistics */
do_getstat_s(&m);
break;
default: /* Invalid message type */
panic(TypeErrMsg, m.m_type);
break;
}
}
return OK; /* Never reached, but keeps compiler happy */
}
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
/*===========================================================================*
* sef_local_startup *
*===========================================================================*/
2012-03-25 20:25:53 +02:00
static void sef_local_startup()
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
{
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
/* Register init callbacks. */
sef_setcb_init_fresh(sef_cb_init_fresh);
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
sef_setcb_init_lu(sef_cb_init_fresh);
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
sef_setcb_init_restart(sef_cb_init_fresh);
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
/* Register live update callbacks. */
sef_setcb_lu_prepare(sef_cb_lu_prepare_always_ready);
sef_setcb_lu_state_isvalid(sef_cb_lu_state_isvalid_workfree);
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
New RS and new signal handling for system processes. UPDATING INFO: 20100317: /usr/src/etc/system.conf updated to ignore default kernel calls: copy it (or merge it) to /etc/system.conf. The hello driver (/dev/hello) added to the distribution: # cd /usr/src/commands/scripts && make clean install # cd /dev && MAKEDEV hello KERNEL CHANGES: - Generic signal handling support. The kernel no longer assumes PM as a signal manager for every process. The signal manager of a given process can now be specified in its privilege slot. When a signal has to be delivered, the kernel performs the lookup and forwards the signal to the appropriate signal manager. PM is the default signal manager for user processes, RS is the default signal manager for system processes. To enable ptrace()ing for system processes, it is sufficient to change the default signal manager to PM. This will temporarily disable crash recovery, though. - sys_exit() is now split into sys_exit() (i.e. exit() for system processes, which generates a self-termination signal), and sys_clear() (i.e. used by PM to ask the kernel to clear a process slot when a process exits). - Added a new kernel call (i.e. sys_update()) to swap two process slots and implement live update. PM CHANGES: - Posix signal handling is no longer allowed for system processes. System signals are split into two fixed categories: termination and non-termination signals. When a non-termination signaled is processed, PM transforms the signal into an IPC message and delivers the message to the system process. When a termination signal is processed, PM terminates the process. - PM no longer assumes itself as the signal manager for system processes. It now makes sure that every system signal goes through the kernel before being actually processes. The kernel will then dispatch the signal to the appropriate signal manager which may or may not be PM. SYSLIB CHANGES: - Simplified SEF init and LU callbacks. - Added additional predefined SEF callbacks to debug crash recovery and live update. - Fixed a temporary ack in the SEF init protocol. SEF init reply is now completely synchronous. - Added SEF signal event type to provide a uniform interface for system processes to deal with signals. A sef_cb_signal_handler() callback is available for system processes to handle every received signal. A sef_cb_signal_manager() callback is used by signal managers to process system signals on behalf of the kernel. - Fixed a few bugs with memory mapping and DS. VM CHANGES: - Page faults and memory requests coming from the kernel are now implemented using signals. - Added a new VM call to swap two process slots and implement live update. - The call is used by RS at update time and in turn invokes the kernel call sys_update(). RS CHANGES: - RS has been reworked with a better functional decomposition. - Better kernel call masks. com.h now defines the set of very basic kernel calls every system service is allowed to use. This makes system.conf simpler and easier to maintain. In addition, this guarantees a higher level of isolation for system libraries that use one or more kernel calls internally (e.g. printf). - RS is the default signal manager for system processes. By default, RS intercepts every signal delivered to every system process. This makes crash recovery possible before bringing PM and friends in the loop. - RS now supports fast rollback when something goes wrong while initializing the new version during a live update. - Live update is now implemented by keeping the two versions side-by-side and swapping the process slots when the old version is ready to update. - Crash recovery is now implemented by keeping the two versions side-by-side and cleaning up the old version only when the recovery process is complete. DS CHANGES: - Fixed a bug when the process doing ds_publish() or ds_delete() is not known by DS. - Fixed the completely broken support for strings. String publishing is now implemented in the system library and simply wraps publishing of memory ranges. Ideally, we should adopt a similar approach for other data types as well. - Test suite fixed. DRIVER CHANGES: - The hello driver has been added to the Minix distribution to demonstrate basic live update and crash recovery functionalities. - Other drivers have been adapted to conform the new SEF interface.
2010-03-17 02:15:29 +01:00
/* Register signal callbacks. */
sef_setcb_signal_handler(sef_cb_signal_handler);
Basic System Event Framework (SEF) with ping and live update. SYSLIB CHANGES: - SEF must be used by every system process and is thereby part of the system library. - The framework provides a receive() interface (sef_receive) for system processes to automatically catch known system even messages and process them. - SEF provides a default behavior for each type of system event, but allows system processes to register callbacks to override the default behavior. - Custom (local to the process) or predefined (provided by SEF) callback implementations can be registered to SEF. - SEF currently includes support for 2 types of system events: 1. SEF Ping. The event occurs every time RS sends a ping to figure out whether a system process is still alive. The default callback implementation provided by SEF is to notify RS back to let it know the process is alive and kicking. 2. SEF Live update. The event occurs every time RS sends a prepare to update message to let a system process know an update is available and to prepare for it. The live update support is very basic for now. SEF only deals with verifying if the prepare state can be supported by the process, dumping the state for debugging purposes, and providing an event-driven programming model to the process to react to state changes check-in when ready to update. - SEF should be extended in the future to integrate support for more types of system events. Ideally, all the cross-cutting concerns should be integrated into SEF to avoid duplicating code and ease extensibility. Examples include: * PM notify messages primarily used at shutdown. * SYSTEM notify messages primarily used for signals. * CLOCK notify messages used for system alarms. * Debug messages. IS could still be in charge of fkey handling but would forward the debug message to the target process (e.g. PM, if the user requested debug information about PM). SEF would then catch the message and do nothing unless the process has registered an appropriate callback to deal with the event. This simplifies the programming model to print debug information, avoids duplicating code, and reduces the effort to print debug information. SYSTEM PROCESSES CHANGES: - Every system process registers SEF callbacks it needs to override the default system behavior and calls sef_startup() right after being started. - sef_startup() does almost nothing now, but will be extended in the future to support callbacks of its own to let RS control and synchronize with every system process at initialization time. - Every system process calls sef_receive() now rather than receive() directly, to let SEF handle predefined system events. RS CHANGES: - RS supports a basic single-component live update protocol now, as follows: * When an update command is issued (via "service update *"), RS notifies the target system process to prepare for a specific update state. * If the process doesn't respond back in time, the update is aborted. * When the process responds back, RS kills it and marks it for refreshing. * The process is then automatically restarted as for a buggy process and can start running again. * Live update is currently prototyped as a controlled failure.
2009-12-21 15:12:21 +01:00
/* Let SEF perform startup. */
sef_startup();
}
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
/*===========================================================================*
* sef_cb_init_fresh *
*===========================================================================*/
2012-03-25 20:25:53 +02:00
static int sef_cb_init_fresh(int type, sef_init_info_t *UNUSED(info))
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
{
/* Initialize the dpeth driver. */
int fkeys, sfkeys;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
long v;
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
/* Request function key for debug dumps */
fkeys = sfkeys = 0; bit_set(sfkeys, 8);
if ((fkey_map(&fkeys, &sfkeys)) != OK)
printf("%s: couldn't program Shift+F8 key (%d)\n", DevName, errno);
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
v = 0;
(void) env_parse("instance", "d", 0, &v, 0, 255);
de_instance = (int) v;
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
Driver refactory for live update and crash recovery. SYSLIB CHANGES: - DS calls to publish / retrieve labels consider endpoints instead of u32_t. VFS CHANGES: - mapdriver() only adds an entry in the dmap table in VFS. - dev_up() is only executed upon reception of a driver up event. INET CHANGES: - INET no longer searches for existing drivers instances at startup. - A newtwork driver is (re)initialized upon reception of a driver up event. - Networking startup is now race-free by design. No need to waste 5 seconds at startup any more. DRIVER CHANGES: - Every driver publishes driver up events when starting for the first time or in case of restart when recovery actions must be taken in the upper layers. - Driver up events are published by drivers through DS. - For regular drivers, VFS is normally the only subscriber, but not necessarily. For instance, when the filter driver is in use, it must subscribe to driver up events to initiate recovery. - For network drivers, inet is the only subscriber for now. - Every VFS driver is statically linked with libdriver, every network driver is statically linked with libnetdriver. DRIVER LIBRARIES CHANGES: - Libdriver is extended to provide generic receive() and ds_publish() interfaces for VFS drivers. - driver_receive() is a wrapper for sef_receive() also used in driver_task() to discard spurious messages that were meant to be delivered to a previous version of the driver. - driver_receive_mq() is the same as driver_receive() but integrates support for queued messages. - driver_announce() publishes a driver up event for VFS drivers and marks the driver as initialized and expecting a DEV_OPEN message. - Libnetdriver is introduced to provide similar receive() and ds_publish() interfaces for network drivers (netdriver_announce() and netdriver_receive()). - Network drivers all support live update with no state transfer now. KERNEL CHANGES: - Added kernel call statectl for state management. Used by driver_announce() to unblock eventual callers sendrecing to the driver.
2010-04-08 15:41:35 +02:00
/* Announce we are up! */
netdriver_announce();
Initialization protocol for system services. SYSLIB CHANGES: - SEF framework now supports a new SEF Init request type from RS. 3 different callbacks are available (init_fresh, init_lu, init_restart) to specify initialization code when a service starts fresh, starts after a live update, or restarts. SYSTEM SERVICE CHANGES: - Initialization code for system services is now enclosed in a callback SEF will automatically call at init time. The return code of the callback will tell RS whether the initialization completed successfully. - Each init callback can access information passed by RS to initialize. As of now, each system service has access to the public entries of RS's system process table to gather all the information required to initialize. This design eliminates many existing or potential races at boot time and provides a uniform initialization interface to system services. The same interface will be reused for the upcoming publish/subscribe model to handle dynamic registration / deregistration of system services. VM CHANGES: - Uniform privilege management for all system services. Every service uses the same call mask format. For boot services, VM copies the call mask from init data. For dynamic services, VM still receives the call mask via rs_set_priv call that will be soon replaced by the upcoming publish/subscribe model. RS CHANGES: - The system process table has been reorganized and split into private entries and public entries. Only the latter ones are exposed to system services. - VM call masks are now entirely configured in rs/table.c - RS has now its own slot in the system process table. Only kernel tasks and user processes not included in the boot image are now left out from the system process table. - RS implements the initialization protocol for system services. - For services in the boot image, RS blocks till initialization is complete and panics when failure is reported back. Services are initialized in their order of appearance in the boot image priv table and RS blocks to implements synchronous initialization for every system service having the flag SF_SYNCH_BOOT set. - For services started dynamically, the initialization protocol is implemented as though it were the first ping for the service. In this case, if the system service fails to report back (or reports failure), RS brings the service down rather than trying to restart it.
2010-01-08 02:20:42 +01:00
return(OK);
}
New RS and new signal handling for system processes. UPDATING INFO: 20100317: /usr/src/etc/system.conf updated to ignore default kernel calls: copy it (or merge it) to /etc/system.conf. The hello driver (/dev/hello) added to the distribution: # cd /usr/src/commands/scripts && make clean install # cd /dev && MAKEDEV hello KERNEL CHANGES: - Generic signal handling support. The kernel no longer assumes PM as a signal manager for every process. The signal manager of a given process can now be specified in its privilege slot. When a signal has to be delivered, the kernel performs the lookup and forwards the signal to the appropriate signal manager. PM is the default signal manager for user processes, RS is the default signal manager for system processes. To enable ptrace()ing for system processes, it is sufficient to change the default signal manager to PM. This will temporarily disable crash recovery, though. - sys_exit() is now split into sys_exit() (i.e. exit() for system processes, which generates a self-termination signal), and sys_clear() (i.e. used by PM to ask the kernel to clear a process slot when a process exits). - Added a new kernel call (i.e. sys_update()) to swap two process slots and implement live update. PM CHANGES: - Posix signal handling is no longer allowed for system processes. System signals are split into two fixed categories: termination and non-termination signals. When a non-termination signaled is processed, PM transforms the signal into an IPC message and delivers the message to the system process. When a termination signal is processed, PM terminates the process. - PM no longer assumes itself as the signal manager for system processes. It now makes sure that every system signal goes through the kernel before being actually processes. The kernel will then dispatch the signal to the appropriate signal manager which may or may not be PM. SYSLIB CHANGES: - Simplified SEF init and LU callbacks. - Added additional predefined SEF callbacks to debug crash recovery and live update. - Fixed a temporary ack in the SEF init protocol. SEF init reply is now completely synchronous. - Added SEF signal event type to provide a uniform interface for system processes to deal with signals. A sef_cb_signal_handler() callback is available for system processes to handle every received signal. A sef_cb_signal_manager() callback is used by signal managers to process system signals on behalf of the kernel. - Fixed a few bugs with memory mapping and DS. VM CHANGES: - Page faults and memory requests coming from the kernel are now implemented using signals. - Added a new VM call to swap two process slots and implement live update. - The call is used by RS at update time and in turn invokes the kernel call sys_update(). RS CHANGES: - RS has been reworked with a better functional decomposition. - Better kernel call masks. com.h now defines the set of very basic kernel calls every system service is allowed to use. This makes system.conf simpler and easier to maintain. In addition, this guarantees a higher level of isolation for system libraries that use one or more kernel calls internally (e.g. printf). - RS is the default signal manager for system processes. By default, RS intercepts every signal delivered to every system process. This makes crash recovery possible before bringing PM and friends in the loop. - RS now supports fast rollback when something goes wrong while initializing the new version during a live update. - Live update is now implemented by keeping the two versions side-by-side and swapping the process slots when the old version is ready to update. - Crash recovery is now implemented by keeping the two versions side-by-side and cleaning up the old version only when the recovery process is complete. DS CHANGES: - Fixed a bug when the process doing ds_publish() or ds_delete() is not known by DS. - Fixed the completely broken support for strings. String publishing is now implemented in the system library and simply wraps publishing of memory ranges. Ideally, we should adopt a similar approach for other data types as well. - Test suite fixed. DRIVER CHANGES: - The hello driver has been added to the Minix distribution to demonstrate basic live update and crash recovery functionalities. - Other drivers have been adapted to conform the new SEF interface.
2010-03-17 02:15:29 +01:00
/*===========================================================================*
* sef_cb_signal_handler *
*===========================================================================*/
2012-03-25 20:25:53 +02:00
static void sef_cb_signal_handler(int signo)
New RS and new signal handling for system processes. UPDATING INFO: 20100317: /usr/src/etc/system.conf updated to ignore default kernel calls: copy it (or merge it) to /etc/system.conf. The hello driver (/dev/hello) added to the distribution: # cd /usr/src/commands/scripts && make clean install # cd /dev && MAKEDEV hello KERNEL CHANGES: - Generic signal handling support. The kernel no longer assumes PM as a signal manager for every process. The signal manager of a given process can now be specified in its privilege slot. When a signal has to be delivered, the kernel performs the lookup and forwards the signal to the appropriate signal manager. PM is the default signal manager for user processes, RS is the default signal manager for system processes. To enable ptrace()ing for system processes, it is sufficient to change the default signal manager to PM. This will temporarily disable crash recovery, though. - sys_exit() is now split into sys_exit() (i.e. exit() for system processes, which generates a self-termination signal), and sys_clear() (i.e. used by PM to ask the kernel to clear a process slot when a process exits). - Added a new kernel call (i.e. sys_update()) to swap two process slots and implement live update. PM CHANGES: - Posix signal handling is no longer allowed for system processes. System signals are split into two fixed categories: termination and non-termination signals. When a non-termination signaled is processed, PM transforms the signal into an IPC message and delivers the message to the system process. When a termination signal is processed, PM terminates the process. - PM no longer assumes itself as the signal manager for system processes. It now makes sure that every system signal goes through the kernel before being actually processes. The kernel will then dispatch the signal to the appropriate signal manager which may or may not be PM. SYSLIB CHANGES: - Simplified SEF init and LU callbacks. - Added additional predefined SEF callbacks to debug crash recovery and live update. - Fixed a temporary ack in the SEF init protocol. SEF init reply is now completely synchronous. - Added SEF signal event type to provide a uniform interface for system processes to deal with signals. A sef_cb_signal_handler() callback is available for system processes to handle every received signal. A sef_cb_signal_manager() callback is used by signal managers to process system signals on behalf of the kernel. - Fixed a few bugs with memory mapping and DS. VM CHANGES: - Page faults and memory requests coming from the kernel are now implemented using signals. - Added a new VM call to swap two process slots and implement live update. - The call is used by RS at update time and in turn invokes the kernel call sys_update(). RS CHANGES: - RS has been reworked with a better functional decomposition. - Better kernel call masks. com.h now defines the set of very basic kernel calls every system service is allowed to use. This makes system.conf simpler and easier to maintain. In addition, this guarantees a higher level of isolation for system libraries that use one or more kernel calls internally (e.g. printf). - RS is the default signal manager for system processes. By default, RS intercepts every signal delivered to every system process. This makes crash recovery possible before bringing PM and friends in the loop. - RS now supports fast rollback when something goes wrong while initializing the new version during a live update. - Live update is now implemented by keeping the two versions side-by-side and swapping the process slots when the old version is ready to update. - Crash recovery is now implemented by keeping the two versions side-by-side and cleaning up the old version only when the recovery process is complete. DS CHANGES: - Fixed a bug when the process doing ds_publish() or ds_delete() is not known by DS. - Fixed the completely broken support for strings. String publishing is now implemented in the system library and simply wraps publishing of memory ranges. Ideally, we should adopt a similar approach for other data types as well. - Test suite fixed. DRIVER CHANGES: - The hello driver has been added to the Minix distribution to demonstrate basic live update and crash recovery functionalities. - Other drivers have been adapted to conform the new SEF interface.
2010-03-17 02:15:29 +01:00
{
/* Only check for termination signal, ignore anything else. */
if (signo != SIGTERM) return;
This patch switches the MINIX3 ethernet driver stack from a port-based model to an instance-based model. Each ethernet driver instance is now responsible for exactly one network interface card. The port field in /etc/inet.conf now acts as an instance field instead. This patch also updates the data link protocol. This update: - eliminates the concept of ports entirely; - eliminates DL_GETNAME entirely; - standardizes on using m_source for IPC and DL_ENDPT for safecopies; - removes error codes from TASK/STAT replies, as they were unused; - removes a number of other old or unused fields; - names and renames a few other fields. All ethernet drivers have been changed to: - conform to the new protocol, and exactly that; - take on an instance number based on a given "instance" argument; - skip that number of PCI devices in probe iterations; - use config tables and environment variables based on that number; - no longer be limited to a predefined maximum of cards in any way; - get rid of any leftover non-safecopy support and other ancient junk; - have a correct banner protocol figure, or none at all. Other changes: * Inet.conf is now taken to be line-based, and supports #-comments. No existing installations are expected to be affected by this. * A new, select-based asynchio library replaces the old one. Kindly contributed by Kees J. Bot. * Inet now supports use of select() on IP devices. Combined, the last two changes together speed up dhcpd considerably in the presence of multiple interfaces. * A small bug has been fixed in nonamed.
2010-05-18 00:22:53 +02:00
if (de_state.de_mode == DEM_ENABLED)
dp_stop(&de_state);
exit(0);
New RS and new signal handling for system processes. UPDATING INFO: 20100317: /usr/src/etc/system.conf updated to ignore default kernel calls: copy it (or merge it) to /etc/system.conf. The hello driver (/dev/hello) added to the distribution: # cd /usr/src/commands/scripts && make clean install # cd /dev && MAKEDEV hello KERNEL CHANGES: - Generic signal handling support. The kernel no longer assumes PM as a signal manager for every process. The signal manager of a given process can now be specified in its privilege slot. When a signal has to be delivered, the kernel performs the lookup and forwards the signal to the appropriate signal manager. PM is the default signal manager for user processes, RS is the default signal manager for system processes. To enable ptrace()ing for system processes, it is sufficient to change the default signal manager to PM. This will temporarily disable crash recovery, though. - sys_exit() is now split into sys_exit() (i.e. exit() for system processes, which generates a self-termination signal), and sys_clear() (i.e. used by PM to ask the kernel to clear a process slot when a process exits). - Added a new kernel call (i.e. sys_update()) to swap two process slots and implement live update. PM CHANGES: - Posix signal handling is no longer allowed for system processes. System signals are split into two fixed categories: termination and non-termination signals. When a non-termination signaled is processed, PM transforms the signal into an IPC message and delivers the message to the system process. When a termination signal is processed, PM terminates the process. - PM no longer assumes itself as the signal manager for system processes. It now makes sure that every system signal goes through the kernel before being actually processes. The kernel will then dispatch the signal to the appropriate signal manager which may or may not be PM. SYSLIB CHANGES: - Simplified SEF init and LU callbacks. - Added additional predefined SEF callbacks to debug crash recovery and live update. - Fixed a temporary ack in the SEF init protocol. SEF init reply is now completely synchronous. - Added SEF signal event type to provide a uniform interface for system processes to deal with signals. A sef_cb_signal_handler() callback is available for system processes to handle every received signal. A sef_cb_signal_manager() callback is used by signal managers to process system signals on behalf of the kernel. - Fixed a few bugs with memory mapping and DS. VM CHANGES: - Page faults and memory requests coming from the kernel are now implemented using signals. - Added a new VM call to swap two process slots and implement live update. - The call is used by RS at update time and in turn invokes the kernel call sys_update(). RS CHANGES: - RS has been reworked with a better functional decomposition. - Better kernel call masks. com.h now defines the set of very basic kernel calls every system service is allowed to use. This makes system.conf simpler and easier to maintain. In addition, this guarantees a higher level of isolation for system libraries that use one or more kernel calls internally (e.g. printf). - RS is the default signal manager for system processes. By default, RS intercepts every signal delivered to every system process. This makes crash recovery possible before bringing PM and friends in the loop. - RS now supports fast rollback when something goes wrong while initializing the new version during a live update. - Live update is now implemented by keeping the two versions side-by-side and swapping the process slots when the old version is ready to update. - Crash recovery is now implemented by keeping the two versions side-by-side and cleaning up the old version only when the recovery process is complete. DS CHANGES: - Fixed a bug when the process doing ds_publish() or ds_delete() is not known by DS. - Fixed the completely broken support for strings. String publishing is now implemented in the system library and simply wraps publishing of memory ranges. Ideally, we should adopt a similar approach for other data types as well. - Test suite fixed. DRIVER CHANGES: - The hello driver has been added to the Minix distribution to demonstrate basic live update and crash recovery functionalities. - Other drivers have been adapted to conform the new SEF interface.
2010-03-17 02:15:29 +01:00
}
/** dp.c **/