minix/kernel/arch/i386/mpx.S

529 lines
13 KiB
ArmAsm
Raw Normal View History

2012-02-14 19:58:27 +01:00
/* This file is part of the lowest layer of the MINIX kernel. (The other part
* is "proc.c".) The lowest layer does process switching and message handling.
* Furthermore it contains the assembler startup code for Minix and the 32-bit
* interrupt handlers. It cooperates with the code in "start.c" to set up a
* good environment for main().
*
* Kernel is entered either because of kernel-calls, ipc-calls, interrupts or
* exceptions. TSS is set so that the kernel stack is loaded. The user context is
* saved to the proc table and the handler of the event is called. Once the
* handler is done, switch_to_user() function is called to pick a new process,
* finish what needs to be done for the next process to run, sets its context
* and switch to userspace.
*
* For communication with the boot monitor at startup time some constant
* data are compiled into the beginning of the text segment. This facilitates
* reading the data at the start of the boot process, since only the first
* sector of the file needs to be read.
*
* Some data storage is also allocated at the end of this file. This data
* will be at the start of the data segment of the kernel and will be read
* and modified by the boot monitor before the kernel starts.
*/
2010-04-02 00:22:33 +02:00
#include "kernel/kernel.h" /* configures the kernel */
NMI watchdog is an awesome feature for debugging locked up kernels. There is not that much use for it on a single CPU, however, deadlock between kernel and system task can be delected. Or a runaway loop. If a kernel gets locked up the timer interrupts don't occure (as all interrupts are disabled in kernel mode). The only chance is to interrupt the kernel by a non-maskable interrupt. This patch generates NMIs using performance counters. It uses the most widely available performace counters. As the performance counters are highly model-specific this patch is not guaranteed to work on every machine. Unfortunately this is also true for KVM :-/ On the other hand adding this feature for other models is not extremely difficult and the framework makes it hopefully easy enough. Depending on the frequency of the CPU an NMI is generated at most about every 0.5s If the cpu's speed is less then 2Ghz it is generated at most every 1s. In general an NMI is generated much less often as the performance counter counts down only if the cpu is not idle. Therefore the overhead of this feature is fairly minimal even if the load is high. Uppon detecting that the kernel is locked up the kernel dumps the state of the kernel registers and panics. Local APIC must be enabled for the watchdog to work. The code is _always_ compiled in, however, it is only enabled if watchdog=<non-zero> is set in the boot monitor. One corner case is serial console debugging. As dumping a lot of stuff to the serial link may take a lot of time, the watchdog does not detect lockups during this time!!! as it would result in too many false positives. 10 nmi have to be handled before the lockup is detected. This means something between ~5s to 10s. Another corner case is that the watchdog is enabled only after the paging is enabled as it would be pure madness to try to get it right.
2010-01-16 21:53:55 +01:00
/* sections */
#include <machine/vm.h>
#include "../../kernel.h"
#include <minix/config.h>
#include <minix/const.h>
#include <minix/com.h>
#include <machine/asm.h>
#include <machine/interrupt.h>
#include "archconst.h"
2010-04-02 00:22:33 +02:00
#include "kernel/const.h"
#include "kernel/proc.h"
#include "sconst.h"
#include <machine/multiboot.h>
#include "arch_proto.h" /* K_STACK_SIZE */
#ifdef CONFIG_SMP
#include "kernel/smp.h"
#endif
/* Selected 386 tss offsets. */
#define TSS3_S_SP0 4
IMPORT(copr_not_available_handler)
IMPORT(params_size)
IMPORT(params_offset)
IMPORT(switch_to_user)
2011-05-04 18:51:43 +02:00
IMPORT(multiboot_init)
.text
/*===========================================================================*/
/* interrupt handlers */
/* interrupt handlers for 386 32-bit protected mode */
/*===========================================================================*/
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
#define PIC_IRQ_HANDLER(irq) \
push $irq ;\
call _C_LABEL(irq_handle) /* intr_handle(irq_handlers[irq]) */ ;\
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
add $4, %esp ;
/*===========================================================================*/
/* hwint00 - 07 */
/*===========================================================================*/
/* Note this is a macro, it just looks like a subroutine. */
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
#define hwint_master(irq) \
TEST_INT_IN_KERNEL(4, 0f) ;\
\
SAVE_PROCESS_CTX(0) ;\
push %ebp ;\
movl $0, %ebp /* for stack trace */ ;\
call _C_LABEL(context_stop) ;\
add $4, %esp ;\
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
PIC_IRQ_HANDLER(irq) ;\
movb $END_OF_INT, %al ;\
outb $INT_CTL /* reenable interrupts in master pic */ ;\
jmp _C_LABEL(switch_to_user) ;\
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
\
0: \
pusha ;\
call _C_LABEL(context_stop_idle) ;\
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
PIC_IRQ_HANDLER(irq) ;\
movb $END_OF_INT, %al ;\
outb $INT_CTL /* reenable interrupts in master pic */ ;\
CLEAR_IF(10*4(%esp)) ;\
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
popa ;\
iret ;
/* Each of these entry points is an expansion of the hwint_master macro */
ENTRY(hwint00)
/* Interrupt routine for irq 0 (the clock). */
hwint_master(0)
ENTRY(hwint01)
/* Interrupt routine for irq 1 (keyboard) */
hwint_master(1)
ENTRY(hwint02)
/* Interrupt routine for irq 2 (cascade!) */
hwint_master(2)
ENTRY(hwint03)
/* Interrupt routine for irq 3 (second serial) */
hwint_master(3)
ENTRY(hwint04)
/* Interrupt routine for irq 4 (first serial) */
hwint_master(4)
ENTRY(hwint05)
/* Interrupt routine for irq 5 (XT winchester) */
hwint_master(5)
ENTRY(hwint06)
/* Interrupt routine for irq 6 (floppy) */
hwint_master(6)
ENTRY(hwint07)
/* Interrupt routine for irq 7 (printer) */
hwint_master(7)
/*===========================================================================*/
/* hwint08 - 15 */
/*===========================================================================*/
/* Note this is a macro, it just looks like a subroutine. */
#define hwint_slave(irq) \
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
TEST_INT_IN_KERNEL(4, 0f) ;\
\
SAVE_PROCESS_CTX(0) ;\
push %ebp ;\
movl $0, %ebp /* for stack trace */ ;\
call _C_LABEL(context_stop) ;\
add $4, %esp ;\
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
PIC_IRQ_HANDLER(irq) ;\
movb $END_OF_INT, %al ;\
outb $INT_CTL /* reenable interrupts in master pic */ ;\
outb $INT2_CTL /* reenable slave 8259 */ ;\
jmp _C_LABEL(switch_to_user) ;\
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
\
0: \
pusha ;\
call _C_LABEL(context_stop_idle) ;\
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
PIC_IRQ_HANDLER(irq) ;\
movb $END_OF_INT, %al ;\
outb $INT_CTL /* reenable interrupts in master pic */ ;\
outb $INT2_CTL /* reenable slave 8259 */ ;\
CLEAR_IF(10*4(%esp)) ;\
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
popa ;\
iret ;
/* Each of these entry points is an expansion of the hwint_slave macro */
ENTRY(hwint08)
/* Interrupt routine for irq 8 (realtime clock) */
hwint_slave(8)
ENTRY(hwint09)
/* Interrupt routine for irq 9 (irq 2 redirected) */
hwint_slave(9)
ENTRY(hwint10)
/* Interrupt routine for irq 10 */
hwint_slave(10)
ENTRY(hwint11)
/* Interrupt routine for irq 11 */
hwint_slave(11)
ENTRY(hwint12)
/* Interrupt routine for irq 12 */
hwint_slave(12)
ENTRY(hwint13)
/* Interrupt routine for irq 13 (FPU exception) */
hwint_slave(13)
ENTRY(hwint14)
/* Interrupt routine for irq 14 (AT winchester) */
hwint_slave(14)
ENTRY(hwint15)
/* Interrupt routine for irq 15 */
hwint_slave(15)
/*
* IPC is only from a process to kernel
*/
ENTRY(ipc_entry)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
SAVE_PROCESS_CTX(0)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
/* save the pointer to the current process */
push %ebp
/*
* pass the syscall arguments from userspace to the handler.
* SAVE_PROCESS_CTX() does not clobber these registers, they are still
* set as the userspace have set them
*/
push %ebx
push %eax
push %ecx
/* stop user process cycles */
push %ebp
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
/* for stack trace */
movl $0, %ebp
call _C_LABEL(context_stop)
add $4, %esp
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
call _C_LABEL(do_ipc)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
/* restore the current process pointer and save the return value */
add $3 * 4, %esp
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
pop %esi
mov %eax, AXREG(%esi)
jmp _C_LABEL(switch_to_user)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
/*
* kernel call is only from a process to kernel
*/
ENTRY(kernel_call_entry)
SAVE_PROCESS_CTX(0)
/* save the pointer to the current process */
push %ebp
/*
* pass the syscall arguments from userspace to the handler.
* SAVE_PROCESS_CTX() does not clobber these registers, they are still
* set as the userspace have set them
*/
push %eax
/* stop user process cycles */
push %ebp
/* for stack trace */
movl $0, %ebp
call _C_LABEL(context_stop)
add $4, %esp
call _C_LABEL(kernel_call)
/* restore the current process pointer and save the return value */
add $8, %esp
jmp _C_LABEL(switch_to_user)
2009-11-13 10:30:45 +01:00
.balign 16
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
/*
* called by the exception interrupt vectors. If the exception does not push
* errorcode, we assume that the vector handler pushed 0 instead. Next pushed
* thing is the vector number. From this point on we can continue as if every
* exception pushes an error code
*/
exception_entry:
/*
* check if it is a nested trap by comparing the saved code segment
* descriptor with the kernel CS first
*/
TEST_INT_IN_KERNEL(12, exception_entry_nested)
exception_entry_from_user:
SAVE_PROCESS_CTX(8)
/* stop user process cycles */
push %ebp
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
/* for stack trace clear %ebp */
movl $0, %ebp
call _C_LABEL(context_stop)
add $4, %esp
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
/*
* push a pointer to the interrupt state pushed by the cpu and the
* vector number pushed by the vector handler just before calling
* exception_entry and call the exception handler.
*/
push %esp
push $0 /* it's not a nested exception */
call _C_LABEL(exception_handler)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
jmp _C_LABEL(switch_to_user)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
exception_entry_nested:
pusha
mov %esp, %eax
add $(8 * 4), %eax
push %eax
pushl $1 /* it's a nested exception */
call _C_LABEL(exception_handler)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
add $8, %esp
popa
/* clear the error code and the exception number */
add $8, %esp
/* resume execution at the point of exception */
iret
/*===========================================================================*/
/* restart */
/*===========================================================================*/
ENTRY(restore_user_context)
mov 4(%esp), %ebp /* will assume P_STACKBASE == 0 */
NMI watchdog is an awesome feature for debugging locked up kernels. There is not that much use for it on a single CPU, however, deadlock between kernel and system task can be delected. Or a runaway loop. If a kernel gets locked up the timer interrupts don't occure (as all interrupts are disabled in kernel mode). The only chance is to interrupt the kernel by a non-maskable interrupt. This patch generates NMIs using performance counters. It uses the most widely available performace counters. As the performance counters are highly model-specific this patch is not guaranteed to work on every machine. Unfortunately this is also true for KVM :-/ On the other hand adding this feature for other models is not extremely difficult and the framework makes it hopefully easy enough. Depending on the frequency of the CPU an NMI is generated at most about every 0.5s If the cpu's speed is less then 2Ghz it is generated at most every 1s. In general an NMI is generated much less often as the performance counter counts down only if the cpu is not idle. Therefore the overhead of this feature is fairly minimal even if the load is high. Uppon detecting that the kernel is locked up the kernel dumps the state of the kernel registers and panics. Local APIC must be enabled for the watchdog to work. The code is _always_ compiled in, however, it is only enabled if watchdog=<non-zero> is set in the boot monitor. One corner case is serial console debugging. As dumping a lot of stuff to the serial link may take a lot of time, the watchdog does not detect lockups during this time!!! as it would result in too many false positives. 10 nmi have to be handled before the lockup is detected. This means something between ~5s to 10s. Another corner case is that the watchdog is enabled only after the paging is enabled as it would be pure madness to try to get it right.
2010-01-16 21:53:55 +01:00
/* reconstruct the stack for iret */
No more intel/minix segments. This commit removes all traces of Minix segments (the text/data/stack memory map abstraction in the kernel) and significance of Intel segments (hardware segments like CS, DS that add offsets to all addressing before page table translation). This ultimately simplifies the memory layout and addressing and makes the same layout possible on non-Intel architectures. There are only two types of addresses in the world now: virtual and physical; even the kernel and processes have the same virtual address space. Kernel and user processes can be distinguished at a glance as processes won't use 0xF0000000 and above. No static pre-allocated memory sizes exist any more. Changes to booting: . The pre_init.c leaves the kernel and modules exactly as they were left by the bootloader in physical memory . The kernel starts running using physical addressing, loaded at a fixed location given in its linker script by the bootloader. All code and data in this phase are linked to this fixed low location. . It makes a bootstrap pagetable to map itself to a fixed high location (also in linker script) and jumps to the high address. All code and data then use this high addressing. . All code/data symbols linked at the low addresses is prefixed by an objcopy step with __k_unpaged_*, so that that code cannot reference highly-linked symbols (which aren't valid yet) or vice versa (symbols that aren't valid any more). . The two addressing modes are separated in the linker script by collecting the unpaged_*.o objects and linking them with low addresses, and linking the rest high. Some objects are linked twice, once low and once high. . The bootstrap phase passes a lot of information (e.g. free memory list, physical location of the modules, etc.) using the kinfo struct. . After this bootstrap the low-linked part is freed. . The kernel maps in VM into the bootstrap page table so that VM can begin executing. Its first job is to make page tables for all other boot processes. So VM runs before RS, and RS gets a fully dynamic, VM-managed address space. VM gets its privilege info from RS as usual but that happens after RS starts running. . Both the kernel loading VM and VM organizing boot processes happen using the libexec logic. This removes the last reason for VM to still know much about exec() and vm/exec.c is gone. Further Implementation: . All segments are based at 0 and have a 4 GB limit. . The kernel is mapped in at the top of the virtual address space so as not to constrain the user processes. . Processes do not use segments from the LDT at all; there are no segments in the LDT any more, so no LLDT is needed. . The Minix segments T/D/S are gone and so none of the user-space or in-kernel copy functions use them. The copy functions use a process endpoint of NONE to realize it's a physical address, virtual otherwise. . The umap call only makes sense to translate a virtual address to a physical address now. . Segments-related calls like newmap and alloc_segments are gone. . All segments-related translation in VM is gone (vir2map etc). . Initialization in VM is simpler as no moving around is necessary. . VM and all other boot processes can be linked wherever they wish and will be mapped in at the right location by the kernel and VM respectively. Other changes: . The multiboot code is less special: it does not use mb_print for its diagnostics any more but uses printf() as normal, saving the output into the diagnostics buffer, only printing to the screen using the direct print functions if a panic() occurs. . The multiboot code uses the flexible 'free memory map list' style to receive the list of free memory if available. . The kernel determines the memory layout of the processes to a degree: it tells VM where the kernel starts and ends and where the kernel wants the top of the process to be. VM then uses this entire range, i.e. the stack is right at the top, and mmap()ped bits of memory are placed below that downwards, and the break grows upwards. Other Consequences: . Every process gets its own page table as address spaces can't be separated any more by segments. . As all segments are 0-based, there is no distinction between virtual and linear addresses, nor between userspace and kernel addresses. . Less work is done when context switching, leading to a net performance increase. (8% faster on my machine for 'make servers'.) . The layout and configuration of the GDT makes sysenter and syscall possible.
2012-05-07 16:03:35 +02:00
push $USER_DS_SELECTOR /* ss */
NMI watchdog is an awesome feature for debugging locked up kernels. There is not that much use for it on a single CPU, however, deadlock between kernel and system task can be delected. Or a runaway loop. If a kernel gets locked up the timer interrupts don't occure (as all interrupts are disabled in kernel mode). The only chance is to interrupt the kernel by a non-maskable interrupt. This patch generates NMIs using performance counters. It uses the most widely available performace counters. As the performance counters are highly model-specific this patch is not guaranteed to work on every machine. Unfortunately this is also true for KVM :-/ On the other hand adding this feature for other models is not extremely difficult and the framework makes it hopefully easy enough. Depending on the frequency of the CPU an NMI is generated at most about every 0.5s If the cpu's speed is less then 2Ghz it is generated at most every 1s. In general an NMI is generated much less often as the performance counter counts down only if the cpu is not idle. Therefore the overhead of this feature is fairly minimal even if the load is high. Uppon detecting that the kernel is locked up the kernel dumps the state of the kernel registers and panics. Local APIC must be enabled for the watchdog to work. The code is _always_ compiled in, however, it is only enabled if watchdog=<non-zero> is set in the boot monitor. One corner case is serial console debugging. As dumping a lot of stuff to the serial link may take a lot of time, the watchdog does not detect lockups during this time!!! as it would result in too many false positives. 10 nmi have to be handled before the lockup is detected. This means something between ~5s to 10s. Another corner case is that the watchdog is enabled only after the paging is enabled as it would be pure madness to try to get it right.
2010-01-16 21:53:55 +01:00
movl SPREG(%ebp), %eax
push %eax
movl PSWREG(%ebp), %eax
push %eax
No more intel/minix segments. This commit removes all traces of Minix segments (the text/data/stack memory map abstraction in the kernel) and significance of Intel segments (hardware segments like CS, DS that add offsets to all addressing before page table translation). This ultimately simplifies the memory layout and addressing and makes the same layout possible on non-Intel architectures. There are only two types of addresses in the world now: virtual and physical; even the kernel and processes have the same virtual address space. Kernel and user processes can be distinguished at a glance as processes won't use 0xF0000000 and above. No static pre-allocated memory sizes exist any more. Changes to booting: . The pre_init.c leaves the kernel and modules exactly as they were left by the bootloader in physical memory . The kernel starts running using physical addressing, loaded at a fixed location given in its linker script by the bootloader. All code and data in this phase are linked to this fixed low location. . It makes a bootstrap pagetable to map itself to a fixed high location (also in linker script) and jumps to the high address. All code and data then use this high addressing. . All code/data symbols linked at the low addresses is prefixed by an objcopy step with __k_unpaged_*, so that that code cannot reference highly-linked symbols (which aren't valid yet) or vice versa (symbols that aren't valid any more). . The two addressing modes are separated in the linker script by collecting the unpaged_*.o objects and linking them with low addresses, and linking the rest high. Some objects are linked twice, once low and once high. . The bootstrap phase passes a lot of information (e.g. free memory list, physical location of the modules, etc.) using the kinfo struct. . After this bootstrap the low-linked part is freed. . The kernel maps in VM into the bootstrap page table so that VM can begin executing. Its first job is to make page tables for all other boot processes. So VM runs before RS, and RS gets a fully dynamic, VM-managed address space. VM gets its privilege info from RS as usual but that happens after RS starts running. . Both the kernel loading VM and VM organizing boot processes happen using the libexec logic. This removes the last reason for VM to still know much about exec() and vm/exec.c is gone. Further Implementation: . All segments are based at 0 and have a 4 GB limit. . The kernel is mapped in at the top of the virtual address space so as not to constrain the user processes. . Processes do not use segments from the LDT at all; there are no segments in the LDT any more, so no LLDT is needed. . The Minix segments T/D/S are gone and so none of the user-space or in-kernel copy functions use them. The copy functions use a process endpoint of NONE to realize it's a physical address, virtual otherwise. . The umap call only makes sense to translate a virtual address to a physical address now. . Segments-related calls like newmap and alloc_segments are gone. . All segments-related translation in VM is gone (vir2map etc). . Initialization in VM is simpler as no moving around is necessary. . VM and all other boot processes can be linked wherever they wish and will be mapped in at the right location by the kernel and VM respectively. Other changes: . The multiboot code is less special: it does not use mb_print for its diagnostics any more but uses printf() as normal, saving the output into the diagnostics buffer, only printing to the screen using the direct print functions if a panic() occurs. . The multiboot code uses the flexible 'free memory map list' style to receive the list of free memory if available. . The kernel determines the memory layout of the processes to a degree: it tells VM where the kernel starts and ends and where the kernel wants the top of the process to be. VM then uses this entire range, i.e. the stack is right at the top, and mmap()ped bits of memory are placed below that downwards, and the break grows upwards. Other Consequences: . Every process gets its own page table as address spaces can't be separated any more by segments. . As all segments are 0-based, there is no distinction between virtual and linear addresses, nor between userspace and kernel addresses. . Less work is done when context switching, leading to a net performance increase. (8% faster on my machine for 'make servers'.) . The layout and configuration of the GDT makes sysenter and syscall possible.
2012-05-07 16:03:35 +02:00
push $USER_CS_SELECTOR /* cs */
NMI watchdog is an awesome feature for debugging locked up kernels. There is not that much use for it on a single CPU, however, deadlock between kernel and system task can be delected. Or a runaway loop. If a kernel gets locked up the timer interrupts don't occure (as all interrupts are disabled in kernel mode). The only chance is to interrupt the kernel by a non-maskable interrupt. This patch generates NMIs using performance counters. It uses the most widely available performace counters. As the performance counters are highly model-specific this patch is not guaranteed to work on every machine. Unfortunately this is also true for KVM :-/ On the other hand adding this feature for other models is not extremely difficult and the framework makes it hopefully easy enough. Depending on the frequency of the CPU an NMI is generated at most about every 0.5s If the cpu's speed is less then 2Ghz it is generated at most every 1s. In general an NMI is generated much less often as the performance counter counts down only if the cpu is not idle. Therefore the overhead of this feature is fairly minimal even if the load is high. Uppon detecting that the kernel is locked up the kernel dumps the state of the kernel registers and panics. Local APIC must be enabled for the watchdog to work. The code is _always_ compiled in, however, it is only enabled if watchdog=<non-zero> is set in the boot monitor. One corner case is serial console debugging. As dumping a lot of stuff to the serial link may take a lot of time, the watchdog does not detect lockups during this time!!! as it would result in too many false positives. 10 nmi have to be handled before the lockup is detected. This means something between ~5s to 10s. Another corner case is that the watchdog is enabled only after the paging is enabled as it would be pure madness to try to get it right.
2010-01-16 21:53:55 +01:00
movl PCREG(%ebp), %eax
push %eax
No more intel/minix segments. This commit removes all traces of Minix segments (the text/data/stack memory map abstraction in the kernel) and significance of Intel segments (hardware segments like CS, DS that add offsets to all addressing before page table translation). This ultimately simplifies the memory layout and addressing and makes the same layout possible on non-Intel architectures. There are only two types of addresses in the world now: virtual and physical; even the kernel and processes have the same virtual address space. Kernel and user processes can be distinguished at a glance as processes won't use 0xF0000000 and above. No static pre-allocated memory sizes exist any more. Changes to booting: . The pre_init.c leaves the kernel and modules exactly as they were left by the bootloader in physical memory . The kernel starts running using physical addressing, loaded at a fixed location given in its linker script by the bootloader. All code and data in this phase are linked to this fixed low location. . It makes a bootstrap pagetable to map itself to a fixed high location (also in linker script) and jumps to the high address. All code and data then use this high addressing. . All code/data symbols linked at the low addresses is prefixed by an objcopy step with __k_unpaged_*, so that that code cannot reference highly-linked symbols (which aren't valid yet) or vice versa (symbols that aren't valid any more). . The two addressing modes are separated in the linker script by collecting the unpaged_*.o objects and linking them with low addresses, and linking the rest high. Some objects are linked twice, once low and once high. . The bootstrap phase passes a lot of information (e.g. free memory list, physical location of the modules, etc.) using the kinfo struct. . After this bootstrap the low-linked part is freed. . The kernel maps in VM into the bootstrap page table so that VM can begin executing. Its first job is to make page tables for all other boot processes. So VM runs before RS, and RS gets a fully dynamic, VM-managed address space. VM gets its privilege info from RS as usual but that happens after RS starts running. . Both the kernel loading VM and VM organizing boot processes happen using the libexec logic. This removes the last reason for VM to still know much about exec() and vm/exec.c is gone. Further Implementation: . All segments are based at 0 and have a 4 GB limit. . The kernel is mapped in at the top of the virtual address space so as not to constrain the user processes. . Processes do not use segments from the LDT at all; there are no segments in the LDT any more, so no LLDT is needed. . The Minix segments T/D/S are gone and so none of the user-space or in-kernel copy functions use them. The copy functions use a process endpoint of NONE to realize it's a physical address, virtual otherwise. . The umap call only makes sense to translate a virtual address to a physical address now. . Segments-related calls like newmap and alloc_segments are gone. . All segments-related translation in VM is gone (vir2map etc). . Initialization in VM is simpler as no moving around is necessary. . VM and all other boot processes can be linked wherever they wish and will be mapped in at the right location by the kernel and VM respectively. Other changes: . The multiboot code is less special: it does not use mb_print for its diagnostics any more but uses printf() as normal, saving the output into the diagnostics buffer, only printing to the screen using the direct print functions if a panic() occurs. . The multiboot code uses the flexible 'free memory map list' style to receive the list of free memory if available. . The kernel determines the memory layout of the processes to a degree: it tells VM where the kernel starts and ends and where the kernel wants the top of the process to be. VM then uses this entire range, i.e. the stack is right at the top, and mmap()ped bits of memory are placed below that downwards, and the break grows upwards. Other Consequences: . Every process gets its own page table as address spaces can't be separated any more by segments. . As all segments are 0-based, there is no distinction between virtual and linear addresses, nor between userspace and kernel addresses. . Less work is done when context switching, leading to a net performance increase. (8% faster on my machine for 'make servers'.) . The layout and configuration of the GDT makes sysenter and syscall possible.
2012-05-07 16:03:35 +02:00
/* Restore segments as the user should see them. */
movw $USER_DS_SELECTOR, %si
movw %si, %ds
movw %si, %es
movw %si, %fs
movw %si, %gs
NMI watchdog is an awesome feature for debugging locked up kernels. There is not that much use for it on a single CPU, however, deadlock between kernel and system task can be delected. Or a runaway loop. If a kernel gets locked up the timer interrupts don't occure (as all interrupts are disabled in kernel mode). The only chance is to interrupt the kernel by a non-maskable interrupt. This patch generates NMIs using performance counters. It uses the most widely available performace counters. As the performance counters are highly model-specific this patch is not guaranteed to work on every machine. Unfortunately this is also true for KVM :-/ On the other hand adding this feature for other models is not extremely difficult and the framework makes it hopefully easy enough. Depending on the frequency of the CPU an NMI is generated at most about every 0.5s If the cpu's speed is less then 2Ghz it is generated at most every 1s. In general an NMI is generated much less often as the performance counter counts down only if the cpu is not idle. Therefore the overhead of this feature is fairly minimal even if the load is high. Uppon detecting that the kernel is locked up the kernel dumps the state of the kernel registers and panics. Local APIC must be enabled for the watchdog to work. The code is _always_ compiled in, however, it is only enabled if watchdog=<non-zero> is set in the boot monitor. One corner case is serial console debugging. As dumping a lot of stuff to the serial link may take a lot of time, the watchdog does not detect lockups during this time!!! as it would result in too many false positives. 10 nmi have to be handled before the lockup is detected. This means something between ~5s to 10s. Another corner case is that the watchdog is enabled only after the paging is enabled as it would be pure madness to try to get it right.
2010-01-16 21:53:55 +01:00
No more intel/minix segments. This commit removes all traces of Minix segments (the text/data/stack memory map abstraction in the kernel) and significance of Intel segments (hardware segments like CS, DS that add offsets to all addressing before page table translation). This ultimately simplifies the memory layout and addressing and makes the same layout possible on non-Intel architectures. There are only two types of addresses in the world now: virtual and physical; even the kernel and processes have the same virtual address space. Kernel and user processes can be distinguished at a glance as processes won't use 0xF0000000 and above. No static pre-allocated memory sizes exist any more. Changes to booting: . The pre_init.c leaves the kernel and modules exactly as they were left by the bootloader in physical memory . The kernel starts running using physical addressing, loaded at a fixed location given in its linker script by the bootloader. All code and data in this phase are linked to this fixed low location. . It makes a bootstrap pagetable to map itself to a fixed high location (also in linker script) and jumps to the high address. All code and data then use this high addressing. . All code/data symbols linked at the low addresses is prefixed by an objcopy step with __k_unpaged_*, so that that code cannot reference highly-linked symbols (which aren't valid yet) or vice versa (symbols that aren't valid any more). . The two addressing modes are separated in the linker script by collecting the unpaged_*.o objects and linking them with low addresses, and linking the rest high. Some objects are linked twice, once low and once high. . The bootstrap phase passes a lot of information (e.g. free memory list, physical location of the modules, etc.) using the kinfo struct. . After this bootstrap the low-linked part is freed. . The kernel maps in VM into the bootstrap page table so that VM can begin executing. Its first job is to make page tables for all other boot processes. So VM runs before RS, and RS gets a fully dynamic, VM-managed address space. VM gets its privilege info from RS as usual but that happens after RS starts running. . Both the kernel loading VM and VM organizing boot processes happen using the libexec logic. This removes the last reason for VM to still know much about exec() and vm/exec.c is gone. Further Implementation: . All segments are based at 0 and have a 4 GB limit. . The kernel is mapped in at the top of the virtual address space so as not to constrain the user processes. . Processes do not use segments from the LDT at all; there are no segments in the LDT any more, so no LLDT is needed. . The Minix segments T/D/S are gone and so none of the user-space or in-kernel copy functions use them. The copy functions use a process endpoint of NONE to realize it's a physical address, virtual otherwise. . The umap call only makes sense to translate a virtual address to a physical address now. . Segments-related calls like newmap and alloc_segments are gone. . All segments-related translation in VM is gone (vir2map etc). . Initialization in VM is simpler as no moving around is necessary. . VM and all other boot processes can be linked wherever they wish and will be mapped in at the right location by the kernel and VM respectively. Other changes: . The multiboot code is less special: it does not use mb_print for its diagnostics any more but uses printf() as normal, saving the output into the diagnostics buffer, only printing to the screen using the direct print functions if a panic() occurs. . The multiboot code uses the flexible 'free memory map list' style to receive the list of free memory if available. . The kernel determines the memory layout of the processes to a degree: it tells VM where the kernel starts and ends and where the kernel wants the top of the process to be. VM then uses this entire range, i.e. the stack is right at the top, and mmap()ped bits of memory are placed below that downwards, and the break grows upwards. Other Consequences: . Every process gets its own page table as address spaces can't be separated any more by segments. . As all segments are 0-based, there is no distinction between virtual and linear addresses, nor between userspace and kernel addresses. . Less work is done when context switching, leading to a net performance increase. (8% faster on my machine for 'make servers'.) . The layout and configuration of the GDT makes sysenter and syscall possible.
2012-05-07 16:03:35 +02:00
/* Same for general-purpose registers. */
RESTORE_GP_REGS(%ebp)
NMI watchdog is an awesome feature for debugging locked up kernels. There is not that much use for it on a single CPU, however, deadlock between kernel and system task can be delected. Or a runaway loop. If a kernel gets locked up the timer interrupts don't occure (as all interrupts are disabled in kernel mode). The only chance is to interrupt the kernel by a non-maskable interrupt. This patch generates NMIs using performance counters. It uses the most widely available performace counters. As the performance counters are highly model-specific this patch is not guaranteed to work on every machine. Unfortunately this is also true for KVM :-/ On the other hand adding this feature for other models is not extremely difficult and the framework makes it hopefully easy enough. Depending on the frequency of the CPU an NMI is generated at most about every 0.5s If the cpu's speed is less then 2Ghz it is generated at most every 1s. In general an NMI is generated much less often as the performance counter counts down only if the cpu is not idle. Therefore the overhead of this feature is fairly minimal even if the load is high. Uppon detecting that the kernel is locked up the kernel dumps the state of the kernel registers and panics. Local APIC must be enabled for the watchdog to work. The code is _always_ compiled in, however, it is only enabled if watchdog=<non-zero> is set in the boot monitor. One corner case is serial console debugging. As dumping a lot of stuff to the serial link may take a lot of time, the watchdog does not detect lockups during this time!!! as it would result in too many false positives. 10 nmi have to be handled before the lockup is detected. This means something between ~5s to 10s. Another corner case is that the watchdog is enabled only after the paging is enabled as it would be pure madness to try to get it right.
2010-01-16 21:53:55 +01:00
No more intel/minix segments. This commit removes all traces of Minix segments (the text/data/stack memory map abstraction in the kernel) and significance of Intel segments (hardware segments like CS, DS that add offsets to all addressing before page table translation). This ultimately simplifies the memory layout and addressing and makes the same layout possible on non-Intel architectures. There are only two types of addresses in the world now: virtual and physical; even the kernel and processes have the same virtual address space. Kernel and user processes can be distinguished at a glance as processes won't use 0xF0000000 and above. No static pre-allocated memory sizes exist any more. Changes to booting: . The pre_init.c leaves the kernel and modules exactly as they were left by the bootloader in physical memory . The kernel starts running using physical addressing, loaded at a fixed location given in its linker script by the bootloader. All code and data in this phase are linked to this fixed low location. . It makes a bootstrap pagetable to map itself to a fixed high location (also in linker script) and jumps to the high address. All code and data then use this high addressing. . All code/data symbols linked at the low addresses is prefixed by an objcopy step with __k_unpaged_*, so that that code cannot reference highly-linked symbols (which aren't valid yet) or vice versa (symbols that aren't valid any more). . The two addressing modes are separated in the linker script by collecting the unpaged_*.o objects and linking them with low addresses, and linking the rest high. Some objects are linked twice, once low and once high. . The bootstrap phase passes a lot of information (e.g. free memory list, physical location of the modules, etc.) using the kinfo struct. . After this bootstrap the low-linked part is freed. . The kernel maps in VM into the bootstrap page table so that VM can begin executing. Its first job is to make page tables for all other boot processes. So VM runs before RS, and RS gets a fully dynamic, VM-managed address space. VM gets its privilege info from RS as usual but that happens after RS starts running. . Both the kernel loading VM and VM organizing boot processes happen using the libexec logic. This removes the last reason for VM to still know much about exec() and vm/exec.c is gone. Further Implementation: . All segments are based at 0 and have a 4 GB limit. . The kernel is mapped in at the top of the virtual address space so as not to constrain the user processes. . Processes do not use segments from the LDT at all; there are no segments in the LDT any more, so no LLDT is needed. . The Minix segments T/D/S are gone and so none of the user-space or in-kernel copy functions use them. The copy functions use a process endpoint of NONE to realize it's a physical address, virtual otherwise. . The umap call only makes sense to translate a virtual address to a physical address now. . Segments-related calls like newmap and alloc_segments are gone. . All segments-related translation in VM is gone (vir2map etc). . Initialization in VM is simpler as no moving around is necessary. . VM and all other boot processes can be linked wherever they wish and will be mapped in at the right location by the kernel and VM respectively. Other changes: . The multiboot code is less special: it does not use mb_print for its diagnostics any more but uses printf() as normal, saving the output into the diagnostics buffer, only printing to the screen using the direct print functions if a panic() occurs. . The multiboot code uses the flexible 'free memory map list' style to receive the list of free memory if available. . The kernel determines the memory layout of the processes to a degree: it tells VM where the kernel starts and ends and where the kernel wants the top of the process to be. VM then uses this entire range, i.e. the stack is right at the top, and mmap()ped bits of memory are placed below that downwards, and the break grows upwards. Other Consequences: . Every process gets its own page table as address spaces can't be separated any more by segments. . As all segments are 0-based, there is no distinction between virtual and linear addresses, nor between userspace and kernel addresses. . Less work is done when context switching, leading to a net performance increase. (8% faster on my machine for 'make servers'.) . The layout and configuration of the GDT makes sysenter and syscall possible.
2012-05-07 16:03:35 +02:00
movl BPREG(%ebp), %ebp
NMI watchdog is an awesome feature for debugging locked up kernels. There is not that much use for it on a single CPU, however, deadlock between kernel and system task can be delected. Or a runaway loop. If a kernel gets locked up the timer interrupts don't occure (as all interrupts are disabled in kernel mode). The only chance is to interrupt the kernel by a non-maskable interrupt. This patch generates NMIs using performance counters. It uses the most widely available performace counters. As the performance counters are highly model-specific this patch is not guaranteed to work on every machine. Unfortunately this is also true for KVM :-/ On the other hand adding this feature for other models is not extremely difficult and the framework makes it hopefully easy enough. Depending on the frequency of the CPU an NMI is generated at most about every 0.5s If the cpu's speed is less then 2Ghz it is generated at most every 1s. In general an NMI is generated much less often as the performance counter counts down only if the cpu is not idle. Therefore the overhead of this feature is fairly minimal even if the load is high. Uppon detecting that the kernel is locked up the kernel dumps the state of the kernel registers and panics. Local APIC must be enabled for the watchdog to work. The code is _always_ compiled in, however, it is only enabled if watchdog=<non-zero> is set in the boot monitor. One corner case is serial console debugging. As dumping a lot of stuff to the serial link may take a lot of time, the watchdog does not detect lockups during this time!!! as it would result in too many false positives. 10 nmi have to be handled before the lockup is detected. This means something between ~5s to 10s. Another corner case is that the watchdog is enabled only after the paging is enabled as it would be pure madness to try to get it right.
2010-01-16 21:53:55 +01:00
iret /* continue process */
/*===========================================================================*/
/* exception handlers */
/*===========================================================================*/
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
#define EXCEPTION_ERR_CODE(vector) \
push $vector ;\
jmp exception_entry
#define EXCEPTION_NO_ERR_CODE(vector) \
pushl $0 ;\
EXCEPTION_ERR_CODE(vector)
LABEL(divide_error)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_NO_ERR_CODE(DIVIDE_VECTOR)
LABEL(single_step_exception)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_NO_ERR_CODE(DEBUG_VECTOR)
LABEL(nmi)
2011-07-29 20:36:42 +02:00
#ifndef USE_WATCHDOG
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_NO_ERR_CODE(NMI_VECTOR)
NMI watchdog is an awesome feature for debugging locked up kernels. There is not that much use for it on a single CPU, however, deadlock between kernel and system task can be delected. Or a runaway loop. If a kernel gets locked up the timer interrupts don't occure (as all interrupts are disabled in kernel mode). The only chance is to interrupt the kernel by a non-maskable interrupt. This patch generates NMIs using performance counters. It uses the most widely available performace counters. As the performance counters are highly model-specific this patch is not guaranteed to work on every machine. Unfortunately this is also true for KVM :-/ On the other hand adding this feature for other models is not extremely difficult and the framework makes it hopefully easy enough. Depending on the frequency of the CPU an NMI is generated at most about every 0.5s If the cpu's speed is less then 2Ghz it is generated at most every 1s. In general an NMI is generated much less often as the performance counter counts down only if the cpu is not idle. Therefore the overhead of this feature is fairly minimal even if the load is high. Uppon detecting that the kernel is locked up the kernel dumps the state of the kernel registers and panics. Local APIC must be enabled for the watchdog to work. The code is _always_ compiled in, however, it is only enabled if watchdog=<non-zero> is set in the boot monitor. One corner case is serial console debugging. As dumping a lot of stuff to the serial link may take a lot of time, the watchdog does not detect lockups during this time!!! as it would result in too many false positives. 10 nmi have to be handled before the lockup is detected. This means something between ~5s to 10s. Another corner case is that the watchdog is enabled only after the paging is enabled as it would be pure madness to try to get it right.
2010-01-16 21:53:55 +01:00
#else
/*
* We have to be very careful as this interrupt can occur anytime. On
* the other hand, if it interrupts a user process, we will resume the
* same process which makes things a little simpler. We know that we are
* already on kernel stack whenever it happened and we can be
* conservative and save everything as we don't need to be extremely
* efficient as the interrupt is infrequent and some overhead is already
* expected.
*/
/*
* save the important registers. We don't save %cs and %ss and they are
* saved and restored by CPU
*/
pushw %ds
pushw %es
pushw %fs
pushw %gs
pusha
/*
* We cannot be sure about the state of the kernel segment register,
* however, we always set %ds and %es to the same as %ss
*/
mov %ss, %si
mov %si, %ds
mov %si, %es
push %esp
call _C_LABEL(nmi_watchdog_handler)
NMI watchdog is an awesome feature for debugging locked up kernels. There is not that much use for it on a single CPU, however, deadlock between kernel and system task can be delected. Or a runaway loop. If a kernel gets locked up the timer interrupts don't occure (as all interrupts are disabled in kernel mode). The only chance is to interrupt the kernel by a non-maskable interrupt. This patch generates NMIs using performance counters. It uses the most widely available performace counters. As the performance counters are highly model-specific this patch is not guaranteed to work on every machine. Unfortunately this is also true for KVM :-/ On the other hand adding this feature for other models is not extremely difficult and the framework makes it hopefully easy enough. Depending on the frequency of the CPU an NMI is generated at most about every 0.5s If the cpu's speed is less then 2Ghz it is generated at most every 1s. In general an NMI is generated much less often as the performance counter counts down only if the cpu is not idle. Therefore the overhead of this feature is fairly minimal even if the load is high. Uppon detecting that the kernel is locked up the kernel dumps the state of the kernel registers and panics. Local APIC must be enabled for the watchdog to work. The code is _always_ compiled in, however, it is only enabled if watchdog=<non-zero> is set in the boot monitor. One corner case is serial console debugging. As dumping a lot of stuff to the serial link may take a lot of time, the watchdog does not detect lockups during this time!!! as it would result in too many false positives. 10 nmi have to be handled before the lockup is detected. This means something between ~5s to 10s. Another corner case is that the watchdog is enabled only after the paging is enabled as it would be pure madness to try to get it right.
2010-01-16 21:53:55 +01:00
add $4, %esp
/* restore all the important registers as they were before the trap */
popa
popw %gs
popw %fs
popw %es
popw %ds
iret
#endif
LABEL(breakpoint_exception)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_NO_ERR_CODE(BREAKPOINT_VECTOR)
LABEL(overflow)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_NO_ERR_CODE(OVERFLOW_VECTOR)
LABEL(bounds_check)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_NO_ERR_CODE(BOUNDS_VECTOR)
LABEL(inval_opcode)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_NO_ERR_CODE(INVAL_OP_VECTOR)
LABEL(copr_not_available)
TEST_INT_IN_KERNEL(4, copr_not_available_in_kernel)
cld /* set direction flag to a known value */
SAVE_PROCESS_CTX(0)
/* stop user process cycles */
push %ebp
mov $0, %ebp
call _C_LABEL(context_stop)
call _C_LABEL(copr_not_available_handler)
/* reached upon failure only */
jmp _C_LABEL(switch_to_user)
copr_not_available_in_kernel:
pushl $0
pushl $COPROC_NOT_VECTOR
jmp exception_entry_nested
LABEL(double_fault)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_ERR_CODE(DOUBLE_FAULT_VECTOR)
LABEL(copr_seg_overrun)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_NO_ERR_CODE(COPROC_SEG_VECTOR)
LABEL(inval_tss)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_ERR_CODE(INVAL_TSS_VECTOR)
LABEL(segment_not_present)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_ERR_CODE(SEG_NOT_VECTOR)
LABEL(stack_exception)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_ERR_CODE(STACK_FAULT_VECTOR)
LABEL(general_protection)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_ERR_CODE(PROTECTION_VECTOR)
LABEL(page_fault)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_ERR_CODE(PAGE_FAULT_VECTOR)
LABEL(copr_error)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
EXCEPTION_NO_ERR_CODE(COPROC_ERR_VECTOR)
LABEL(alignment_check)
EXCEPTION_NO_ERR_CODE(ALIGNMENT_CHECK_VECTOR)
LABEL(machine_check)
EXCEPTION_NO_ERR_CODE(MACHINE_CHECK_VECTOR)
LABEL(simd_exception)
EXCEPTION_NO_ERR_CODE(SIMD_EXCEPTION_VECTOR)
/*===========================================================================*/
/* reload_cr3 */
/*===========================================================================*/
/* PUBLIC void reload_cr3(void); */
ENTRY(reload_cr3)
push %ebp
mov %esp, %ebp
mov %cr3, %eax
mov %eax, %cr3
pop %ebp
ret
#ifdef CONFIG_SMP
ENTRY(startup_ap_32)
/*
* we are in protected mode now, %cs is correct and we need to set the
* data descriptors before we can touch anything
*
* first load the regular, highly mapped idt, gdt
*/
/*
* use the boot stack for now. The running CPUs are already using their
* own stack, the rest is still waiting to be booted
*/
movw $KERN_DS_SELECTOR, %ax
mov %ax, %ds
mov %ax, %ss
mov $_C_LABEL(k_boot_stktop) - 4, %esp
/* load the highly mapped idt, gdt, per-cpu tss */
call _C_LABEL(prot_load_selectors)
jmp _C_LABEL(smp_ap_boot)
hlt
#endif
/*===========================================================================*/
/* data */
/*===========================================================================*/
.data
.short 0x526F /* this must be the first data entry (magic #) */
.bss
No more intel/minix segments. This commit removes all traces of Minix segments (the text/data/stack memory map abstraction in the kernel) and significance of Intel segments (hardware segments like CS, DS that add offsets to all addressing before page table translation). This ultimately simplifies the memory layout and addressing and makes the same layout possible on non-Intel architectures. There are only two types of addresses in the world now: virtual and physical; even the kernel and processes have the same virtual address space. Kernel and user processes can be distinguished at a glance as processes won't use 0xF0000000 and above. No static pre-allocated memory sizes exist any more. Changes to booting: . The pre_init.c leaves the kernel and modules exactly as they were left by the bootloader in physical memory . The kernel starts running using physical addressing, loaded at a fixed location given in its linker script by the bootloader. All code and data in this phase are linked to this fixed low location. . It makes a bootstrap pagetable to map itself to a fixed high location (also in linker script) and jumps to the high address. All code and data then use this high addressing. . All code/data symbols linked at the low addresses is prefixed by an objcopy step with __k_unpaged_*, so that that code cannot reference highly-linked symbols (which aren't valid yet) or vice versa (symbols that aren't valid any more). . The two addressing modes are separated in the linker script by collecting the unpaged_*.o objects and linking them with low addresses, and linking the rest high. Some objects are linked twice, once low and once high. . The bootstrap phase passes a lot of information (e.g. free memory list, physical location of the modules, etc.) using the kinfo struct. . After this bootstrap the low-linked part is freed. . The kernel maps in VM into the bootstrap page table so that VM can begin executing. Its first job is to make page tables for all other boot processes. So VM runs before RS, and RS gets a fully dynamic, VM-managed address space. VM gets its privilege info from RS as usual but that happens after RS starts running. . Both the kernel loading VM and VM organizing boot processes happen using the libexec logic. This removes the last reason for VM to still know much about exec() and vm/exec.c is gone. Further Implementation: . All segments are based at 0 and have a 4 GB limit. . The kernel is mapped in at the top of the virtual address space so as not to constrain the user processes. . Processes do not use segments from the LDT at all; there are no segments in the LDT any more, so no LLDT is needed. . The Minix segments T/D/S are gone and so none of the user-space or in-kernel copy functions use them. The copy functions use a process endpoint of NONE to realize it's a physical address, virtual otherwise. . The umap call only makes sense to translate a virtual address to a physical address now. . Segments-related calls like newmap and alloc_segments are gone. . All segments-related translation in VM is gone (vir2map etc). . Initialization in VM is simpler as no moving around is necessary. . VM and all other boot processes can be linked wherever they wish and will be mapped in at the right location by the kernel and VM respectively. Other changes: . The multiboot code is less special: it does not use mb_print for its diagnostics any more but uses printf() as normal, saving the output into the diagnostics buffer, only printing to the screen using the direct print functions if a panic() occurs. . The multiboot code uses the flexible 'free memory map list' style to receive the list of free memory if available. . The kernel determines the memory layout of the processes to a degree: it tells VM where the kernel starts and ends and where the kernel wants the top of the process to be. VM then uses this entire range, i.e. the stack is right at the top, and mmap()ped bits of memory are placed below that downwards, and the break grows upwards. Other Consequences: . Every process gets its own page table as address spaces can't be separated any more by segments. . As all segments are 0-based, there is no distinction between virtual and linear addresses, nor between userspace and kernel addresses. . Less work is done when context switching, leading to a net performance increase. (8% faster on my machine for 'make servers'.) . The layout and configuration of the GDT makes sysenter and syscall possible.
2012-05-07 16:03:35 +02:00
k_initial_stack:
.space K_STACK_SIZE
LABEL(__k_unpaged_k_initial_stktop)
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
/*
2010-03-18 17:18:22 +01:00
* the kernel stack
Complete ovehaul of mode switching code - after a trap to kernel, the code automatically switches to kernel stack, in the future local to the CPU - k_reenter variable replaced by a test whether the CS is kernel cs or not. The information is passed further if needed. Removes a global variable which would need to be cpu local - no need for global variables describing the exception or trap context. This information is kept on stack and a pointer to this structure is passed to the C code as a single structure - removed loadedcr3 variable and its use replaced by reading the %cr3 register - no need to redisable interrupts in restart() as they are already disabled. - unified handling of traps that push and don't push errorcode - removed save() function as the process context is not saved directly to process table but saved as required by the trap code. Essentially it means that save() code is inlined everywhere not only in the exception handling routine - returning from syscall is more arch independent - it sets the retger in C - top of the x86 stack contains the current CPU id and pointer to the currently scheduled process (the one right interrupted) so the mode switch code can find where to save the context without need to use proc_ptr which will be cpu local in the future and therefore difficult to access in assembler and expensive to access in general - some more clean up of level0 code. No need to read-back the argument passed in %eax from the proc structure. The mode switch code does not clobber %the general registers and hence we can just call what is in %eax - many assebly macros in sconst.h as they will be reused by the apic assembly
2009-11-06 10:08:26 +01:00
*/
k_boot_stack:
.space K_STACK_SIZE /* kernel stack */ /* FIXME use macro here */
LABEL(k_boot_stktop) /* top of kernel stack */
.balign K_STACK_SIZE
LABEL(k_stacks_start)
/* two pages for each stack, one for data, other as a sandbox */
.space 2 * (K_STACK_SIZE * CONFIG_MAX_CPUS)
LABEL(k_stacks_end)
/* top of kernel stack */