This patch adds the notion of voltage domains, and groups clock domains that operate under the same voltage (i.e. power supply) into domains. Each clock domain is required to be associated with a voltage domain, and the latter requires the voltage to be explicitly set. A voltage domain is an independently controllable voltage supply being provided to section of the design. Thus, if you wish to perform dynamic voltage scaling on a CPU, its clock domain should be associated with a separate voltage domain. The current implementation of the voltage domain does not take into consideration cases where there are derived voltage domains running at ratio of native voltage domains, as with the case where there can be on-chip buck/boost (charge pumps) voltage regulation logic. The regression and configuration scripts are updated with a generic voltage domain for the system, and one for the CPUs.
104 lines
4.6 KiB
Python
104 lines
4.6 KiB
Python
# Copyright (c) 2006 The Regents of The University of Michigan
|
|
# All rights reserved.
|
|
#
|
|
# Redistribution and use in source and binary forms, with or without
|
|
# modification, are permitted provided that the following conditions are
|
|
# met: redistributions of source code must retain the above copyright
|
|
# notice, this list of conditions and the following disclaimer;
|
|
# redistributions in binary form must reproduce the above copyright
|
|
# notice, this list of conditions and the following disclaimer in the
|
|
# documentation and/or other materials provided with the distribution;
|
|
# neither the name of the copyright holders nor the names of its
|
|
# contributors may be used to endorse or promote products derived from
|
|
# this software without specific prior written permission.
|
|
#
|
|
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
|
|
# A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
|
|
# OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
|
|
# SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
|
|
# LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
|
|
# DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
|
|
# THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
# (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
|
# OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
#
|
|
# Authors: Lisa Hsu
|
|
|
|
import m5
|
|
from m5.objects import *
|
|
m5.util.addToPath('../configs/common')
|
|
from FSConfig import *
|
|
from Benchmarks import *
|
|
|
|
test_sys = makeLinuxAlphaSystem('atomic',
|
|
SysConfig('netperf-stream-client.rcS'))
|
|
|
|
# Dummy voltage domain for all test_sys clock domains
|
|
test_sys.voltage_domain = VoltageDomain()
|
|
|
|
# Create the system clock domain
|
|
test_sys.clk_domain = SrcClockDomain(clock = '1GHz',
|
|
voltage_domain = test_sys.voltage_domain)
|
|
|
|
test_sys.cpu = AtomicSimpleCPU(cpu_id=0)
|
|
# create the interrupt controller
|
|
test_sys.cpu.createInterruptController()
|
|
test_sys.cpu.connectAllPorts(test_sys.membus)
|
|
|
|
# Create a seperate clock domain for components that should run at
|
|
# CPUs frequency
|
|
test_sys.cpu.clk_domain = SrcClockDomain(clock = '2GHz',
|
|
voltage_domain =
|
|
test_sys.voltage_domain)
|
|
|
|
# Create a separate clock domain for Ethernet
|
|
test_sys.tsunami.ethernet.clk_domain = SrcClockDomain(clock = '500MHz',
|
|
voltage_domain =
|
|
test_sys.voltage_domain)
|
|
|
|
# In contrast to the other (one-system) Tsunami configurations we do
|
|
# not have an IO cache but instead rely on an IO bridge for accesses
|
|
# from masters on the IO bus to the memory bus
|
|
test_sys.iobridge = Bridge(delay='50ns', ranges = test_sys.mem_ranges)
|
|
test_sys.iobridge.slave = test_sys.iobus.master
|
|
test_sys.iobridge.master = test_sys.membus.slave
|
|
|
|
test_sys.physmem = SimpleMemory(range = test_sys.mem_ranges[0])
|
|
test_sys.physmem.port = test_sys.membus.master
|
|
|
|
drive_sys = makeLinuxAlphaSystem('atomic',
|
|
SysConfig('netperf-server.rcS'))
|
|
# Dummy voltage domain for all drive_sys clock domains
|
|
drive_sys.voltage_domain = VoltageDomain()
|
|
# Create the system clock domain
|
|
drive_sys.clk_domain = SrcClockDomain(clock = '1GHz',
|
|
voltage_domain =
|
|
drive_sys.voltage_domain)
|
|
drive_sys.cpu = AtomicSimpleCPU(cpu_id=0)
|
|
# create the interrupt controller
|
|
drive_sys.cpu.createInterruptController()
|
|
drive_sys.cpu.connectAllPorts(drive_sys.membus)
|
|
|
|
# Create a seperate clock domain for components that should run at
|
|
# CPUs frequency
|
|
drive_sys.cpu.clk_domain = SrcClockDomain(clock = '4GHz',
|
|
voltage_domain =
|
|
drive_sys.voltage_domain)
|
|
|
|
# Create a separate clock domain for Ethernet
|
|
drive_sys.tsunami.ethernet.clk_domain = SrcClockDomain(clock = '500MHz',
|
|
voltage_domain =
|
|
drive_sys.voltage_domain)
|
|
|
|
drive_sys.iobridge = Bridge(delay='50ns', ranges = drive_sys.mem_ranges)
|
|
drive_sys.iobridge.slave = drive_sys.iobus.master
|
|
drive_sys.iobridge.master = drive_sys.membus.slave
|
|
|
|
drive_sys.physmem = SimpleMemory(range = drive_sys.mem_ranges[0])
|
|
drive_sys.physmem.port = drive_sys.membus.master
|
|
|
|
root = makeDualRoot(True, test_sys, drive_sys, "ethertrace")
|
|
|
|
maxtick = 199999999
|