This patch adds a simple counter for both total messages and a histogram for
the fan-out of snoop messages. The fan-out describes to how many ports snoops
had to be sent per incoming request / snoop-from-below. Without any
cleverness, this usually means to either all, or all but the requesting port.
This is a first cut at a simple snoop filter that tracks presence of lines in
the caches "above" it. The snoop filter can be applied at any given cache
hierarchy and will then handle the caches above it appropriately; there is no
need to use this only in the last-level bus.
This design currently has some limitations: missing stats, no notion of clean
evictions (these will not update the underlying snoop filter, because they are
not sent from the evicting cache down), no notion of capacity for the snoop
filter and thus no need for invalidations caused by capacity pressure in the
snoop filter. These are planned to be added on top with future change sets.
Added the following parameter to the DRAMCtrl class:
- bank_groups_per_rank
This defaults to 1. For the DDR4 case, the default is overridden to indicate
bank group architecture, with multiple bank groups per rank.
Added the following delays to the DRAMCtrl class:
- tCCD_L : CAS-to-CAS, same bank group delay
- tRRD_L : RAS-to-RAS, same bank group delay
These parameters are only applied when bank group timing is enabled. Bank
group timing is currently enabled only for DDR4 memories.
For all other memories, these delays will default to '0 ns'
In the DRAM controller model, applied the bank group timing to the per bank
parameters actAllowedAt and colAllowedAt.
The actAllowedAt will be updated based on bank group when an ACT is issued.
The colAllowedAt will be updated based on bank group when a RD/WR burst is
issued.
At the moment no modifications are made to the scheduling.
Add the following delay to the DRAM controller:
- tCS : Different rank bus turnaround delay
This will be applied for
1) read-to-read,
2) write-to-write,
3) write-to-read, and
4) read-to-write
command sequences, where the new command accesses a different rank
than the previous burst.
The delay defaults to 2*tCK for each defined memory class. Note that
this does not correspond to one particular timing constraint, but is a
way of modelling all the associated constraints.
The DRAM controller has some minor changes to prioritize commands to
the same rank. This prioritization will only occur when the command
stream is not switching from a read to write or vice versa (in the
case of switching we have a gap in any case).
To prioritize commands to the same rank, the model will determine if there are
any commands queued (same type) to the same rank as the previous command.
This check will ensure that the 'same rank' command will be able to execute
without adding bubbles to the command flow, e.g. any ACT delay requirements
can be done under the hoods, allowing the burst to issue seamlessly.
There are two primary issues with this code which make it deserving of deletion.
1) GHB is a way to structure a prefetcher, not a definitive type of prefetcher
2) This prefetcher isn't even structured like a GHB prefetcher.
It's basically a worse version of the stride prefetcher.
It primarily serves to confuse new gem5 users and most functionality is already
present in the stride prefetcher.
The changeset ad9c042dce54 made changes to the structures under the network
directory to use a map of buffers instead of vector of buffers.
The reasoning was that not all vnets that are created are used and we
needlessly allocate more buffers than required and then iterate over them
while processing network messages. But the move to map resulted in a slow
down which was pointed out by Andreas Hansson. This patch moves things
back to using vector of message buffers.
Static analysis unearther a bunch of uninitialised variables and
members, and this patch addresses the problem. In all cases these
omissions seem benign in the end, but at least fixing them means less
false positives next time round.
This patch tidies up random number generation to ensure that it is
done consistently throughout the code base. In essence this involves a
clean-up of Ruby, and some code simplifications in the traffic
generator.
As part of this patch a bunch of skewed distributions (off-by-one etc)
have been fixed.
Note that a single global random number generator is used, and that
the object instantiation order will impact the behaviour (the sequence
of numbers will be unaffected, but if module A calles random before
module B then they would obviously see a different outcome). The
dependency on the instantiation order is true in any case due to the
execution-model of gem5, so we leave it as is. Also note that the
global ranom generator is not thread safe at this point.
Regressions using the memtest, TrafficGen or any Ruby tester are
affected and will be updated accordingly.
This patch removes unecessary retries that happened when the bus layer
itself was no longer busy, but the the peer was not yet ready. Instead
of sending a retry that will inevitably not succeed, the bus now
silenty waits until the peer sends a retry.
Support full-block writes directly rather than requiring RMW:
* a cache line is allocated in the cache upon receipt of a
WriteInvalidateReq, not the WriteInvalidateResp.
* only top-level caches allocate the line; the others just pass
the request along and invalidate as necessary.
* to close a timing window between the *Req and the *Resp, a new
metadata bit tracks whether another cache has read a copy of
the new line before the writeback to memory.
This patch fixes a bug in the cache port where the retry flag was
reset too early, allowing new requests to arrive before the retry was
actually sent, but with the event already scheduled. This caused a
deadlock in the interactions with the O3 LSQ.
The patche fixes the underlying issue by shifting the resetting of the
flag to be done by the event that also calls sendRetry(). The patch
also tidies up the flow control in recvTimingReq and ensures that we
also check if we already have a retry outstanding.
Previously, they were treated so much like loads that they could stall
at the head of the ROB. Now they are always treated like L1 hits.
If they actually miss, a new request is created at the L1 and tracked
from the MSHRs there if necessary (i.e. if it didn't coalesce with
an existing outstanding load).
If a set of LL/SC requests contend on the same cache block we
can get into a situation where CPUs will deadlock if they expect
a failed SC to supply them data. This case happens where 3 or
more cores are contending for a cache block using LL/SC and the system
is configured where 2 cores are connected to a local bus and the
third is connected to a remote bus. If a core on the local bus
sends an SCUpgrade and the core on the remote bus sends and SCUpgrade
they will race to see who will win the SC access. In the meantime
if the other core appends a read to one of the SCUpgrades it will expect
to be supplied data by that SCUpgrade transaction. If it happens that
the SCUpgrade that was picked to supply the data is failed, it will
drop the appended request for data and never respond, leaving the requesting
core to deadlock. This patch makes all SC's behave as normal stores to
prevent this case but still makes sure to check whether it can perform
the update.
This patch prunes unused values, and also unifies how the values are
defined (not using an enum for ALPHA), aligning the use of int vs Addr
etc.
The patch also removes the duplication of PageBytes/PageShift and
VMPageSize/LogVMPageSize. For all ISAs the two pairs had identical
values and the latter has been removed.
The Index type defined as typedef int64 does not really provide any help
since in most places we use primitive types instead of Index. Also, the name
Index is very generic that it does not merit being used as a typename.
This patch is the final patch in a series of patches. The aim of the series
is to make ruby more configurable than it was. More specifically, the
connections between controllers are not at all possible (unless one is ready
to make significant changes to the coherence protocol). Moreover the buffers
themselves are magically connected to the network inside the slicc code.
These connections are not part of the configuration file.
This patch makes changes so that these connections will now be made in the
python configuration files associated with the protocols. This requires
each state machine to expose the message buffers it uses for input and output.
So, the patch makes these buffers configurable members of the machines.
The patch drops the slicc code that usd to connect these buffers to the
network. Now these buffers are exposed to the python configuration system
as Master and Slave ports. In the configuration files, any master port
can be connected any slave port. The file pyobject.cc has been modified to
take care of allocating the actual message buffer. This is inline with how
other port connections work.
A later changeset changes the file src/python/swig/pyobject.cc to include
a header file that includes a header file generated at build time depending
on the PROTOCOL in use. Since NULL ISA was not specifying any protocol,
this resulted in compilation problems. Hence, the changeset.
The namespace Message conflicts with the Message data type used extensively
in Ruby. Since Ruby is being moved to the same Master/Slave ports based
configuration style as the rest of gem5, this conflict needs to be resolved.
Hence, the namespace is being renamed to ProtoMessage.
There are two changes this patch makes to the way configurable members of a
state machine are specified in SLICC. The first change is that the data
member declarations will need to be separated by a semi-colon instead of a
comma. Secondly, the default value to be assigned would now use SLICC's
assignment operator i.e. ':='.
This patch changes the grammar for SLICC so as to remove some of the
redundant / duplicate rules. In particular rules for object/variable
declaration and class member declaration have been unified. Similarly, the
rules for a general function and a class method have been unified.
One more change is in the priority of two rules. The first rule is on
declaring a function with all the params typed and named. The second rule is
on declaring a function with all the params only typed. Earlier the second
rule had a higher priority. Now the first rule has a higher priority.
This patch enables the use of page tables that are stored in system memory
and respect x86 specification, in SE mode. It defines an architectural
page table for x86 as a MultiLevelPageTable class and puts a placeholder
class for other ISAs page tables, giving the possibility for future
implementation.
This patch defines a multi-level page table class that stores the page table in
system memory, consistent with ISA specifications. In this way, cpu models that
use the actual hardware to execute (e.g. KvmCPU), are able to traverse the page
table.
This patch ensures the cycle check is still valid even restoring from
a checkpoint. In this case the DRAMSim2 cycle count is relative to the
startTick rather than 0.
This patch fixes a bug in the DRAM controller address decoding. In
cases where the DRAM burst size (e.g. 32 bytes in a rank with a single
LPDDR3 x32) was smaller than the channel interleaving size
(e.g. systems with a 64-byte cache line) one address bit effectively
got used as a channel bit when it should have been a low-order column
bit.
This patch adds a notion of "columns per stripe", and more clearly
deals with the low-order column bits and high-order column bits. The
patch also relaxes the granularity check such that it is possible to
use interleaving granularities other than the cache line size.
The patch also adds a missing M5_CLASS_VAR_USED to the tCK member as
it is only used in the debug build for now.
When a cacheline is written back to a lower-level cache,
tags->insertBlock() sets various status parameters. However these
status bits were cleared immediately after calling. This patch makes
it so that these status fields are not cleared by moving them outside
of the tags->insertBlock() call.
this patch implements a new tags class that uses a random replacement policy.
these tags prefer to evict invalid blocks first, if none are available a
replacement candidate is chosen at random.
this patch factors out the common code in the LRU class and creates a new
abstract class: the BaseSetAssoc class. any set associative tag class must
implement the functionality related to the actual replacement policy in the
following methods:
accessBlock()
findVictim()
insertBlock()
invalidate()
This patch adds a DRAMPower flag to enable off-line DRAM power
analysis using the DRAMPower tool. A new DRAMPower flag is added
and a follow-on patch adds a Python script to post-process the output
and order it based on time stamps.
The long-term goal is to link DRAMPower as a library and provide the
commands through function calls to the model rather than first
printing and then parsing the commands. At the moment it is also up to
the user to ensure that the same DRAM configuration is used by the
gem5 controller model and DRAMPower.
This patch adds the index of the bank and rank as a field so that we can
determine the identity of a given bank (reference or pointer) for the
power tracing. We also grab the opportunity of cleaning up the
arguments used for identifying the bank when activating.
Using '== true' in a boolean expression is totally redundant,
and using '== false' is pretty verbose (and arguably less
readable in most cases) compared to '!'.
It's somewhat of a pet peeve, perhaps, but I had some time
waiting for some tests to run and decided to clean these up.
Unfortunately, SLICC appears not to have the '!' operator,
so I had to leave the '== false' tests in the SLICC code.
This patch makes a more firm connection between the DDR3-1600
configuration and the corresponding datasheet, and also adds a
DDR3-2133 and a DDR4-2400 configuration. At the moment there is also
an ongoing effort to align the choice of datasheets to what is
available in DRAMPower.
