The EIOProcess class was removed recently and it was the only other class
which derived from Process. Since every Process invocation is also a
LiveProcess invocation, it makes sense to simplify the organization by
combining the fields from LiveProcess into Process.
Names of DRAM configurations were updated to reflect both
the channel and device data width.
Previous naming format was:
<DEVICE_TYPE>_<DATA_RATE>_<CHANNEL_WIDTH>
The following nomenclature is now used:
<DEVICE_TYPE>_<DATA_RATE>_<n>x<w>
where n = The number of devices per rank on the channel
x = Device width
Total channel width can be calculated by n*w
Example:
A 64-bit DDR4, 2400 channel consisting of 4-bit devices:
n = 16
w = 4
The resulting configuration name is:
DDR4_2400_16x4
Updated scripts to match new naming convention.
Added unique configurations for DDR4 for:
1) 16x4
2) 8x8
3) 4x16
Change-Id: Ibd7f763b7248835c624309143cb9fc29d56a69d1
Reviewed-by: Radhika Jagtap <radhika.jagtap@arm.com>
Reviewed-by: Curtis Dunham <curtis.dunham@arm.com>
The current TLM bridge only provides a Slave Port that allows the gem5
world to send request to the SystemC world. This patch series refractors
and cleans up the existing code, and adds a Master Port that allows the
SystemC world to send requests to the gem5 world.
This patch:
* Restructure the existing sources in preparation of the addition of the
* new
Master Port.
* Refractor names to allow for distinction of the slave and master port.
* Replace the Makefile by a SConstruct.
Testing Done: The examples provided in util/tlm (now
util/tlm/examples/slave_port) still compile and run error free.
Reviewed at http://reviews.gem5.org/r/3527/
Signed-off-by: Jason Lowe-Power <jason@lowepower.com>
If the cache access mode is parallel, i.e. "sequential_access" parameter
is set to "False", tags and data are accessed in parallel. Therefore,
the hit_latency is the maximum latency between tag_latency and
data_latency. On the other hand, if the cache access mode is
sequential, i.e. "sequential_access" parameter is set to "True",
tags and data are accessed sequentially. Therefore, the hit_latency
is the sum of tag_latency plus data_latency.
Signed-off-by: Jason Lowe-Power <jason@lowepower.com>
This patch adds the ability for an application to request dist-gem5 to begin/
end synchronization using an m5 op. When toggling on sync, all nodes agree
on the next sync point based on the maximum of all nodes' ticks. CPUs are
suspended until the sync point to avoid sending network messages until sync has
been enabled. Toggling off sync acts like a global execution barrier, where
all CPUs are disabled until every node reaches the toggle off point. This
avoids tricky situations such as one node hitting a toggle off followed by a
toggle on before the other nodes hit the first toggle off.
This patch breaks out the most basic configuration options into a set
of base options, to allow them to be used also by scripts that do not
involve any ISA, and thus no actual CPUs or devices.
The patch also fixes a few modules so that they can be imported in a
NULL build, and avoid dragging in FSConfig every time Options is
imported.
Modify the opClass assigned to AArch64 FP instructions from SimdFloat* to
Float*. Also create the FloatMemRead and FloatMemWrite opClasses, which
distinguishes writes to the INT and FP register banks.
Change the latency of (Simd)FloatMultAcc to 5, based on the Cortex-A72,
where the "latency" of FMADD is 3 if the next instruction is a FMADD and
has only the augend to destination dependency, otherwise it's 7 cycles.
Signed-off-by: Jason Lowe-Power <jason@lowepower.com>
Continue along the same line as the recent patch that made the
Ruby-related config scripts Python packages and make also the
configs/common directory a package.
All affected config scripts are updated (hopefully).
Note that this change makes it apparent that the current organisation
and naming of the config directory and its subdirectories is rather
chaotic. We mix scripts that are directly invoked with scripts that
merely contain convenience functions. While it is not addressed in
this patch we should follow up with a re-organisation of the
config structure, and renaming of some of the packages.
This patch moves the addition of network options into the Ruby module
to avoid the regressions all having to add it explicitly. Doing this
exposes an issue in our current config system though, namely the fact
that addtoPath is relative to the Python script being executed. Since
both example and regression scripts use the Ruby module we would end
up with two different (relative) paths being added. Instead we take a
first step at turning the config modules into Python packages, simply
by adding a __init__.py in the configs/ruby, configs/topologies and
configs/network subdirectories.
As a result, we can now add the top-level configs directory to the
Python search path, and then use the package names in the various
modules. The example scripts are also updated, and the messy
path-deducing variations in the scripts are unified.
This patch changes the default behaviour of the SystemXBar, adding a
snoop filter. With the recent updates to the snoop filter allocation
behaviour this change no longer causes problems for the regressions
without caches.
Change-Id: Ibe0cd437b71b2ede9002384126553679acc69cc1
Reviewed-by: Nikos Nikoleris <nikos.nikoleris@arm.com>
Reviewed-by: Jason Lowe-Power <jason@lowepower.com>
Reviewed-by: Tony Gutierrez <anthony.gutierrez@amd.com>
Ruby on ARM is currently very experimental. Fail with a fatal error
that explains this to make sure users are aware of the limitations (it
doesn't actually work yet!).
Signed-off-by: Andreas Sandberg <andreas.sandberg@arm.com>
Add initial support for creating an ARM system with a Ruby-based
memory system. This support is currently experimental and limited to
the new VExpress_GEM5_V1 platform.
Change-Id: I36baeb68b0d891e34ea46aafe17b5e55217b4bfa
Signed-off-by: Andreas Sandberg <andreas.sandberg@arm.com>
Reviewed-by: Nikos Nikoleris <nikos.nikoleris@arm.com>
Reviewed-by: Jason Lowe-Power <jason@lowepower.com>
Reviewed-by: Brad Beckmann <brad.beckmann@amd.com>
At the moment the SPARC FS machine configuration comes with a hardcoded
value for using the Solaris 10 disk image from the OpenSPARC tarball. The
--disk-image option is completely ignored for SPARC. This simple patch
modifies the behavior so that --disk-image option is both taken into
account and also required. This makes it possible to easily change SPARC FS
images without having to modify the configuration files.
In this new hmc configuration we have used the existing components in gem5
mainly [SerialLink] [NoncoherentXbar]& [DRAMCtrl] to define 3 different
architecture for HMC.
Highlights
1- It explores 3 different HMC architectures
2- It creates 4-HMC crossbars and attaches 16 vault controllers with it.
This will connect vaults to serial links
3- From the previous version, HMCController with round robin funtionality
is being removed and all the serial links are being accessible directly
from user ports
4- Latency incorporated by HMCController (in previous version) is being
added to SerialLink
Committed by Jason Lowe-Power <jason@lowepower.com>
This patch ensures a walker cache is instantiated if specfied.
Change-Id: I2c6b4bf3454d56bb19558c73b406e1875acbd986
Reviewed-by: Curtis Dunham <curtis.dunham@arm.com>
Reviewed-by: Mitch Hayenga <mitch.hayenga@arm.com>
Disable the default snoop filter in the SystemXBar so that the
typical membus does not have a snoop filter by default. Instead,
add the snoop filter only when there are caches added to the system
(with the caches / l2cache options).
The underlying problem is that the snoop filter grows without
bounds (for now) if there are no caches to tell it that lines have
been evicted. This causes slow regression runs for all the atomic
regressions. This patch fixes this behaviour.
--HG--
extra : source : f97c20511828209757440839ed48d741d02d428f
According to the Intel Multi Processor Specification rev 1.4 (-006) (*),
section 4.3.2 Bus Entries, Bus type strings are >>6-character ASCII
(blank-filled) strings<<.
This patch properly pads the entries with the missing spaces at the end.
(*) http://www.intel.com/design/pentium/datashts/24201606.pdf
Committed by Jason Lowe-Power <power.jg@gmail.com>
This patch changes how the cache determines if snoops should be
forwarded from the memory side to the CPU side. Instead of having a
parameter, the cache now looks at the port connected on the CPU side,
and if it is a snooping port, then snoops are forwarded. Less error
prone, and less parameters to worry about.
The patch also tidies up the CPU classes to ensure that their I-side
port is not snooping by removing overrides to the snoop request
handler, such that snoop requests will panic via the default
MasterPort implement
Add a platform with support for both aarch32 and aarch64. This
platform implements a subset of the devices in a real Versatile
Express and extends it with some gem5-specific functionality. It is in
many ways similar to the old VExpress_EMM64 platform, but supports the
following new features:
* Automatic PCI interrupt assignment
* PCI interrupts allocated in a contiguous range.
* Automatic boot loader selection (32-bit / 64-bit)
* Cleaner memory map where gem5-specific devices live in CS5 which
isn't used by current Versatile Express platforms.
* No fake devices. Devices that were previously faked will be
removed from the device tree instead.
* Support for 510 GiB contiguous memory
This patch adds changes to the configuration scripts to support elastic
tracing and replay.
The patch adds a command line option to enable elastic tracing in SE mode
and FS mode. When enabled the Elastic Trace cpu probe is attached to O3CPU
and a few O3 CPU parameters are tuned. The Elastic Trace probe writes out
both instruction fetch and data dependency traces. The patch also enables
configuring the TraceCPU to replay traces using the SE and FS script.
The replay run is designed to resume from checkpoint using atomic cpu to
restore state keeping it consistent with FS run flow. It then switches to
TraceCPU to replay the input traces.
The gem5's current PCI host functionality is very ad hoc. The current
implementations require PCI devices to be hooked up to the
configuration space via a separate configuration port. Devices query
the platform to get their config-space address range. Un-mapped parts
of the config space are intercepted using the XBar's default port
mechanism and a magic catch-all device (PciConfigAll).
This changeset redesigns the PCI host functionality to improve code
reuse and make config-space and interrupt mapping more
transparent. Existing platform code has been updated to use the new
PCI host and configured to stay backwards compatible (i.e., no
guest-side visible changes). The current implementation does not
expose any new functionality, but it can easily be extended with
features such as automatic interrupt mapping.
PCI devices now register themselves with a PCI host controller. The
host controller interface is defined in the abstract base class
PciHost. Registration is done by PciHost::registerDevice() which takes
the device, its bus position (bus/dev/func tuple), and its interrupt
pin (INTA-INTC) as a parameter. The registration interface returns a
PciHost::DeviceInterface that the PCI device can use to query memory
mappings and signal interrupts.
The host device manages the entire PCI configuration space. Accesses
to devices decoded into the devices bus position and then forwarded to
the correct device.
Basic PCI host functionality is implemented in the GenericPciHost base
class. Most platforms can use this class as a basic PCI controller. It
provides the following functionality:
* Configurable configuration space decoding. The number of bits
dedicated to a device is a prameter, making it possible to support
both CAM, ECAM, and legacy mappings.
* Basic interrupt mapping using the interruptLine value from a
device's configuration space. This behavior is the same as in the
old implementation. More advanced controllers can override the
interrupt mapping method to dynamically assign host interrupts to
PCI devices.
* Simple (base + addr) remapping from the PCI bus's address space to
physical addresses for PIO, memory, and DMA.
Add support for automatically discover available platforms. The
Python-side uses functionality similar to what we use when
auto-detecting available CPU models. The machine IDs have been updated
to match the platform configurations. If there isn't a matching
machine ID, the configuration scripts default to -1 which Linux uses
for device tree only platforms.
This patch adds the necessary commands and cache functionality to
allow clean writebacks. This functionality is crucial, especially when
having exclusive (victim) caches. For example, if read-only L1
instruction caches are not sending clean writebacks, there will never
be any spills from the L1 to the L2. At the moment the cache model
defaults to not sending clean writebacks, and this should possibly be
re-evaluated.
The implementation of clean writebacks relies on a new packet command
WritebackClean, which acts much like a Writeback (renamed
WritebackDirty), and also much like a CleanEvict. On eviction of a
clean block the cache either sends a clean evict, or a clean
writeback, and if any copies are still cached upstream the clean
evict/writeback is dropped. Similarly, if a clean evict/writeback
reaches a cache where there are outstanding MSHRs for the block, the
packet is dropped. In the typical case though, the clean writeback
allocates a block in the downstream cache, and marks it writable if
the evicted block was writable.
The patch changes the O3_ARM_v7a L1 cache configuration and the
default L1 caches in config/common/Caches.py
This patch adds a parameter to control the cache clusivity, that is if
the cache is mostly inclusive or exclusive. At the moment there is no
intention to support strict policies, and thus the options are: 1)
mostly inclusive, or 2) mostly exclusive.
The choice of policy guides the behaviuor on a cache fill, and a new
helper function, allocOnFill, is created to encapsulate the decision
making process. For the timing mode, the decision is annotated on the
MSHR on sending out the downstream packet, and in atomic we directly
pass the decision to handleFill. We (ab)use the tempBlock in cases
where we are not allocating on fill, leaving the rest of the cache
unaffected. Simple and effective.
This patch also makes it more explicit that multiple caches are
allowed to consider a block writable (this is the case
also before this patch). That is, for a mostly inclusive cache,
multiple caches upstream may also consider the block exclusive. The
caches considering the block writable/exclusive all appear along the
same path to memory, and from a coherency protocol point of view it
works due to the fact that we always snoop upwards in zero time before
querying any downstream cache.
Note that this patch does not introduce clean writebacks. Thus, for
clean lines we are essentially removing a cache level if it is made
mostly exclusive. For example, lines from the read-only L1 instruction
cache or table-walker cache are always clean, and simply get dropped
rather than being passed to the L2. If the L2 is mostly exclusive and
does not allocate on fill it will thus never hold the line. A follow
on patch adds the clean writebacks.
The patch changes the L2 of the O3_ARM_v7a CPU configuration to be
mostly exclusive (and stats are affected accordingly).
This patch enables modeling a complete Hybrid Memory Cube (HMC) device. It
highly reuses the existing components in gem5's general memory system with some
small modifications. This changeset requires additional patches to model a
complete HMC device.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
makeSparcSystem() in configs/common/FSConfig.py is missing the cmdLine
parameter Without the parameter the simulation fails to start. With the
parameter the simulation starts properly.
Added a new directory in configs (learning_gem5) to hold the scripts that are
used in the book. See http://lowepower.com/jason/learning_gem5/ for a working
copy. For now, only the scripts in Part 1: Getting started with gem5
have been added. A separate patch adds tests for these scripts.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
Open up for other subclasses to BaseCache and transition to using the
explicit Cache subclass.
--HG--
rename : src/mem/cache/BaseCache.py => src/mem/cache/Cache.py
Transaction Level Modeling (TLM2.0) is widely used in industry for creating
virtual platforms (IEEE 1666 SystemC). This patch contains a standard compliant
implementation of an external gem5 port, that enables the usage of gem5 as a
TLM initiator component in SystemC based virtual platforms. Both TLM coding
paradigms loosely timed (b_transport) and aproximately timed (nb_transport) are
supported.
Compared to the original patch a TLM memory manager was added. Furthermore, the
transaction object was removed and for each TLM payload a PacketPointer that
points to the original gem5 packet is added as an TLM extension. For event
handling single events are now created.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch takes the final step in removing the is_top_level parameter
from the cache. With the recent changes to read requests and write
invalidations, the parameter is no longer needed, and consequently
removed.
This also means that asymmetric cache hierarchies are now fully
supported (and we are actually using them already with L1 caches, but
no table-walker caches, connected to a shared L2).
This patch adds a parameter to the BaseCache to enable a read-only
cache, for example for the instruction cache, or table-walker cache
(not for x86). A number of checks are put in place in the code to
ensure a read-only cache does not end up with dirty data.
A follow-on patch adds suitable read requests to allow a read-only
cache to explicitly ask for clean data.
This changeset adds support for aarch64 in kvm. The CPU module
supports both checkpointing and online CPU model switching as long as
no devices are simulated by the host kernel. It currently has the
following limitations:
* The system register based generic timer can only be simulated by
the host kernel. Workaround: Use a memory mapped timer instead to
simulate the timer in gem5.
* Simulating devices (e.g., the generic timer) in the host kernel
requires that the host kernel also simulates the GIC.
* ID registers in the host and in gem5 must match for switching
between simulated CPUs and KVM. This is particularly important
for ID registers describing memory system capabilities (e.g.,
ASID size, physical address size).
* Switching between a virtualized CPU and a simulated CPU is
currently not supported if in-kernel device emulation is
used. This could be worked around by adding support for switching
to the gem5 (e.g., the KvmGic) side of the device models. A
simpler workaround is to avoid in-kernel device models
altogether.
This patch simplifies the overall CPU by changing the TLB caches such
that they do not forward snoops to the table walker port(s). Note that
only ARM and X86 are affected.
There is no reason for the ports to snoop as they do not actually take
any action, and from a performance point of view we are better of not
snooping more than we have to.
Should it at a later point be required to snoop for a particular TLB
design it is easy enough to add it back.
Currently, each op class has a parameter issueLat that denotes the cycles after
which another op of the same class can be issued. As of now, this latency can
either be one cycle (fully pipelined) or same as execution latency of the op
(not at all pipelined). The fact that issueLat is a parameter of type Cycles
makes one believe that it can be set to any value. To avoid the confusion, the
parameter is being renamed as 'pipelined' with type boolean. If set to true,
the op would execute in a fully pipelined fashion. Otherwise, it would execute
in an unpipelined fashion.
This patch ensures that the CPU progress Event is triggered for the new set of
switched_cpus that get scheduled (e.g. during fast-forwarding). it also avoids
printing the interval state if the cpu is currently switched out.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
This patch adds an example configuration in ext/sst/tests/ that allows
an SST/gem5 instance to simulate a 4-core AArch64 system with SST's
memHierarchy components providing all the caches and memories.
When using gem5 as a slave simulator, it will not advance the
clock on its own and depends on the master simulator calling
simulate(). This new option lets us use the Python scripts
to do all the configuration while stopping short of actually
simulating anything.
This patch enables users to speficy --os-type on the command
line. This option is used to take specific actions for an OS type,
such as changing the kernel command line. This patch is part of the
Android KitKat enablement.
