This patch adds the notion of voltage domains, and groups clock
domains that operate under the same voltage (i.e. power supply) into
domains. Each clock domain is required to be associated with a voltage
domain, and the latter requires the voltage to be explicitly set.
A voltage domain is an independently controllable voltage supply being
provided to section of the design. Thus, if you wish to perform
dynamic voltage scaling on a CPU, its clock domain should be
associated with a separate voltage domain.
The current implementation of the voltage domain does not take into
consideration cases where there are derived voltage domains running at
ratio of native voltage domains, as with the case where there can be
on-chip buck/boost (charge pumps) voltage regulation logic.
The regression and configuration scripts are updated with a generic
voltage domain for the system, and one for the CPUs.
This patch moves the instantiation of the memory controller outside
FSConfig and instead relies on the mem_ranges to pass the information
to the caller (e.g. fs.py or one of the regression scripts). The main
motivation for this change is to expose the structural composition of
the memory system and allow more tuning and configuration without
adding a large number of options to the makeSystem functions.
The patch updates the relevant example scripts to maintain the current
functionality. As the order that ports are connected to the memory bus
changes (in certain regresisons), some bus stats are shuffled
around. For example, what used to be layer 0 is now layer 1.
Going forward, options will be added to support the addition of
multi-channel memory controllers.
This patch contains three fixes to max tick options handling in Options.py and
Simulation.py:
1) Since the global simulator frequency isn't bound until m5.instantiate()
is called, the maxtick resolution needs to happen after this call, since
changes to the global frequency will cause m5.simulate() to misinterpret the
maxtick value. Shuffling this also requires tweaking the checkpoint directory
handling to signal the checkpoint restore tick back to run(). Fixing this
completely and correctly will require storing the simulation frequency into
checkpoints, which is beyond the scope of this patch.
2) The maxtick option in Options.py was defaulted to MaxTicks, so the old code
would always skip over the maxtime part of the conditionals at the beginning
of run(). Change the maxtick default to None, and set the maxtick local
variable in run() appropriately.
3) To clarify whether max ticks settings are relative or absolute, split the
maxtick option into separate options, for relative and absolute. Ensure that
these two options and the maxtime option are handled appropriately to set the
maxtick variable in Simulation.py.
This patch adds the notion of source- and derived-clock domains to the
ClockedObjects. As such, all clock information is moved to the clock
domain, and the ClockedObjects are grouped into domains.
The clock domains are either source domains, with a specific clock
period, or derived domains that have a parent domain and a divider
(potentially chained). For piece of logic that runs at a derived clock
(a ratio of the clock its parent is running at) the necessary derived
clock domain is created from its corresponding parent clock
domain. For now, the derived clock domain only supports a divider,
thus ensuring a lower speed compared to its parent. Multiplier
functionality implies a PLL logic that has not been modelled yet
(create a separate clock instead).
The clock domains should be used as a mechanism to provide a
controllable clock source that affects clock for every clocked object
lying beneath it. The clock of the domain can (in a future patch) be
controlled by a handler responsible for dynamic frequency scaling of
the respective clock domains.
All the config scripts have been retro-fitted with clock domains. For
the System a default SrcClockDomain is created. For CPUs that run at a
different speed than the system, there is a seperate clock domain
created. This domain incorporates the CPU and the associated
caches. As before, Ruby runs under its own clock domain.
The clock period of all domains are pre-computed, such that no virtual
functions or multiplications are needed when calling
clockPeriod. Instead, the clock period is pre-computed when any
changes occur. For this to be possible, each clock domain tracks its
children.
This patch adds a 'sys_clock' command-line option and use it to assign
clocks to the system during instantiation.
As part of this change, the default clock in the System class is
removed and whenever a system is instantiated a system clock value
must be set. A default value is provided for the command-line option.
The configs and tests are updated accordingly.
This patch adds a 'cpu_clock' command-line option and uses the value
to assign clocks to components running at the CPU speed (L1 and L2
including the L2-bus). The configuration scripts are updated
accordingly.
The 'clock' option is left unchanged in this patch as it is still used
by a number of components. In follow-on patches the latter will be
disambiguated further.
The --restore-with-cpu option didn't use CpuConfig.cpu_names() to
determine which CPU names are valid, instead it used a static list of
known CPU names. This changeset makes the option parsing code use the
CPU list from the CpuConfig module instead.
This patch changes the class names of the variuos DRAM configurations
to better reflect what memory they are based on. The speed and
interface width is now part of the name, and also the alias that is
used to select them on the command line.
Some minor changes are done to the actual parameters, to better
reflect the named configurations. As a result of these changes the
regressions change slightly and the stats will be bumped in a separate
patch.
This patch adds a typical (leaning towards fast) LPDDR3 configuration
based on publically available data. As expected, it looks very similar
to the LPDDR2-S4 configuration, only with a slightly lower burst time.
This patch removes the explicit memset as it is redundant and causes
the simulator to touch the entire space, forcing the host system to
allocate the pages.
Anonymous pages are mapped on the first access, and the page-fault
handler is responsible for zeroing them. Thus, the pages are still
zeroed, but we avoid touching the entire allocated space which enables
us to use much larger memory sizes as long as not all the memory is
actually used.
having separate params for the local/globalHistoryBits and the
local/globalPredictorSize can lead to inconsistencies if they
are not carefully set. this patch dervies the number of bits
necessary to index into the local/global predictors based on
their size.
the value of the localHistoryTableSize for the ARM O3 CPU has been
increased to 1024 from 64, which is more accurate for an A15 based
on some correlation against A15 hardware.
This patch enables selection of the memory controller class through a
mem-type command-line option. Behind the scenes, this option is
treated much like the cpu-type, and a similar framework is used to
resolve the valid options, and translate the short-hand description to
a valid class.
The regression scripts are updated with a hardcoded memory class for
the moment. The best solution going forward is probably to get the
memory out of the makeSystem functions, but Ruby complicates things as
it does not connect the memory controller to the membus.
--HG--
rename : configs/common/CpuConfig.py => configs/common/MemConfig.py
This patch is based on http://reviews.m5sim.org/r/1474/ originally written by
Mitch Hayenga. Basic block vectors are generated (simpoint.bb.gz in simout
folder) based on start and end addresses of basic blocks.
Some comments to the original patch are addressed and hooks are added to create
and resume from checkpoints based on instruction counts dictated by external
SimPoint analysis tools.
SimPoint creation/resuming options will be implemented as a separate patch.
In Simulation.py, calls to m5.simulate(num_ticks) will run the simulated system
for num_ticks after the current tick. Fix calls to m5.simulate in
scriptCheckpoints() and benchCheckpoints() to appropriately handle the maxticks
variable.
As of now, we mark the top 1MB of memory space as unusable. Part of
it is actually usable and is required to be marked so by some of the
newer versions of linux kernel. This patch marks the top 639KB as usable.
This value was chosen by looking at QEMU's output for bios memory map.
The default cache configuration script currently import the O3_ARM_v7a
model configuration, which depends on the O3 CPU. This breaks if gem5
has been compiled without O3 support. This changeset removes the
dependency by only importing the model if it is requested by the
user. As a bonus, it actually removes some code duplication in the
configuration scripts.
CPU switching consists of the following steps:
1. Drain the system
2. Switch out old CPUs (cpu.switchOut())
3. Change the system timing mode to the mode the new CPUs require
4. Flush caches if switching to hardware virtualization
5. Inform new CPUs of the handover (cpu.takeOverFrom())
6. Resume the system
m5.switchCpus() previously only did step 2 & 5. Since information
about the new processors' memory system requirements is now exposed,
do all of the steps above.
This patch adds automatic memory system switching and flush (if
needed) to switchCpus(). Additionally, it adds optional draining to
switchCpus(). This has the following implications:
* changeToTiming and changeToAtomic are no longer needed, so they have
been removed.
* changeMemoryMode is only used internally, so it is has been renamed
to be private.
* switchCpus requires a reference to the system containing the CPUs as
its first parameter.
WARNING: This changeset breaks compatibility with existing
configuration scripts since it changes the signature of
m5.switchCpus().
The CPUs supported by the configuration scripts used to be
hard-coded. This was not ideal for several reasons. For example, the
configuration scripts depend on all CPU models even though only a
subset might have been compiled.
This changeset adds a new module to the configuration scripts that
automatically discovers the available CPU models from the compiled
SimObjects. As a nice bonus, the use of introspection allows us to
automatically generate a list of available CPU models suitable for
printing. This list is augmented with the Python doc string from the
underlying class if available.
The configuration scripts currently hard-code the requirements of each
CPU. This is clearly not optimal as it makes writing new configuration
scripts painful and adding new CPU models requires existing scripts to
be updated. This patch adds the following class methods to the base
CPU and all relevant CPUs:
* memory_mode -- Return a string describing the current memory mode
(invalid/atomic/timing).
* require_caches -- Does the CPU model require caches?
* support_take_over -- Does the CPU support CPU handover?
The run() method in Simulation.py used to call sys.exit() when the
simulator exits. This is undesirable when user has requested the
simulator to be run in interactive mode since it causes the simulator
to exit rather than entering the interactive Python environment.
This patch moves the default DRAM parameters from the SimpleDRAM class
to two different subclasses, one for DDR3 and one for LPDDR2. More can
be added as we go forward.
The regressions that previously used the SimpleDRAM are now using
SimpleDDR3 as this is the most similar configuration.
This patch moves the branch predictor files in the o3 and inorder directories
to src/cpu/pred. This allows sharing the branch predictor across different
cpu models.
This patch was originally posted by Timothy Jones in July 2010
but never made it to the repository.
--HG--
rename : src/cpu/o3/bpred_unit.cc => src/cpu/pred/bpred_unit.cc
rename : src/cpu/o3/bpred_unit.hh => src/cpu/pred/bpred_unit.hh
rename : src/cpu/o3/bpred_unit_impl.hh => src/cpu/pred/bpred_unit_impl.hh
rename : src/cpu/o3/sat_counter.hh => src/cpu/pred/sat_counter.hh
Used as a command in full-system scripts helps the user ensure the benchmarks have finished successfully.
For example, one can use:
/path/to/benchmark args || /sbin/m5 fail 1
and thus ensure gem5 will exit with an error if the benchmark fails.
The defer_registration parameter is used to prevent a CPU from
initializing at startup, leaving it in the "switched out" mode. The
name of this parameter (and the help string) is confusing. This patch
renames it to switched_out, which should be more descriptive.
This patch generalises the address range resolution for the I/O cache
and I/O bridge such that they do not assume a single memory. The patch
involves adding a parameter to the system which is then defined based
on the memories that are to be visible from the I/O subsystem, whether
behind a cache or a bridge.
The change is needed to allow interleaved memory controllers in the
system.
globalHistoryBits, globalPredictorSize, and choicePredictorSize are decoupled.
globalHistoryBits controls how much history is kept, global and choice
predictor sizes control how much of that history is used when accessing
predictor tables. This way, global and choice predictors can actually be
different sizes, and it is no longer possible to walk off the predictor arrays
and cause a seg fault.
There are now individual thresholds for choice, global, and local saturating
counters, so that taken/not taken decisions are correct even when the
predictors' counters' sizes are different.
The interface for localPredictorSize has been removed from TournamentBP because
the value can be calculated from localHistoryBits.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
There is no point in exporting the old drain() method in
Simulate.py. It should only be used internally by doDrain(). This
patch moves the old drain() method into doDrain() and renames
doDrain() to drain().
Changeset 4f54b0f229b5 removed the call to doDrain in changeToTiming
based on the assumption that the system does not need draining when
running in atomic mode. This is a false assumption since at least the
System class requires the system to be drained before it allows
switching of memory modes. This patch reverts that part of the
changeset.
This patch unified the L1 and L2 caches used throughout the
regressions instead of declaring different, but very similar,
configurations in the different scripts.
The patch also changes the default L2 configuration to match what it
used to be for the fs and se scripts (until the last patch that
updated the regressions to also make use of the cache config). The
MSHRs and targets per MSHR are now set to a more realistic default of
20 and 12, respectively.
As a result of both the aforementioned changes, many of the regression
stats are changed. A follow-on patch will bump the stats.
This patch favours using SimpleDRAM with the default timing instead of
SimpleMemory for all regressions that involve the o3 or inorder CPU,
or are full system (in other words, where the actual performance of
the memory is important for the overall performance).
Moving forward, the solution for FSConfig and the users of fs.py and
se.py is probably something similar to what we use to choose the CPU
type. I envision a few pre-set configurations SimpleLPDDR2,
SimpleDDR3, etc that can be choosen by a dram_type option. Feedback on
this part is welcome.
This patch changes plenty stats and adds all the DRAM controller
related stats. A follow-on patch updates the relevant statistics. The
total run-time for the entire regression goes up with ~5% with this
patch due to the added complexity of the SimpleDRAM model. This is a
concious trade-off to ensure that the model is properly tested.
This patch uses the common L1, L2 and IOCache configuration for the
regressions that all share the same cache parameters. There are a few
regressions that use a slightly different configuration (memtest,
o3-timing=mp, simple-atomic-mp and simple-timing-mp), and the latter
are not changed in this patch. They will be updated in a future patch.
The common cache configurations are changed to match the ones used in
the regressions, and are slightly changed with respect to what they
were. Hopefully this means we can converge on a common base
configuration, used both in the normal user configurations and
regressions.
As only regressions that shared the same cache configuration are
updated, no regressions are affected.
This patch changes the cache-related latencies from an absolute time
expressed in Ticks, to a number of cycles that can be scaled with the
clock period of the caches. Ultimately this patch serves to enable
future work that involves dynamic frequency scaling. As an immediate
benefit it also makes it more convenient to specify cache performance
without implicitly assuming a specific CPU core operating frequency.
The stat blocked_cycles that actually counter in ticks is now updated
to count in cycles.
As the timing is now rounded to the clock edges of the cache, there
are some regressions that change. Plenty of them have very minor
changes, whereas some regressions with a short run-time are perturbed
quite significantly. A follow-on patch updates all the statistics for
the regressions.
This patch changes the CoherentBus between the L1s and L2 to use the
CPU clock and also four times the width compared to the default
bus. The parameters are not intending to fit every single scenario,
but rather serve as a better startingpoint than what we previously
had.
Note that the scripts that do not use the addTwoLevelCacheHiearchy are
not affected by this change.
A separate patch will update the stats.
In the current caches the hit latency is paid twice on a miss. This patch lets
a configurable response latency be set of the cache for the backward path.
This patch simplifies the Range object hierarchy in preparation for an
address range class that also allows striping (e.g. selecting a few
bits as matching in addition to the range).
To extend the AddrRange class to an AddrRegion, the first step is to
simplify the hierarchy such that we can make it as lean as possible
before adding the new functionality. The only class using Range and
MetaRange is AddrRange, and the three classes are now collapsed into
one.
When switching from an atomic CPU to any of the timing CPUs, a drain is
unnecessary since no events are scheduled in atomic mode. However, when
trying to switch CPUs starting with a timing CPU, there may be events
scheduled. This change ensures that all events are drained from the system
by calling m5.drain before switching CPUs.
This patch allows for specifying multiple programs via command line. It also
adds an option for specifying whether to use of SMT. But SMT does not work for
the o3 cpu as of now.
This patch removes the NACKing in the bridge, as the split
request/response busses now ensure that protocol deadlocks do not
occur, i.e. the message-dependency chain is broken by always allowing
responses to make progress without being stalled by requests. The
NACKs had limited support in the system with most components ignoring
their use (with a suitable call to panic), and as the NACKs are no
longer needed to avoid protocol deadlocks, the cleanest way is to
simply remove them.
The bridge is the starting point as this is the only place where the
NACKs are created. A follow-up patch will remove the code that deals
with NACKs in the endpoints, e.g. the X86 table walker and DMA
port. Ultimately the type of packet can be complete removed (until
someone sees a need for modelling more complex protocols, which can
now be done in parts of the system since the port and interface is
split).
As a consequence of the NACK removal, the bridge now has to send a
retry to a master if the request or response queue was full on the
first attempt. This change also makes the bridge ports very similar to
QueuedPorts, and a later patch will change the bridge to use these. A
first step in this direction is taken by aligning the name of the
member functions, as done by this patch.
A bit of tidying up has also been done as part of the simplifications.
Surprisingly, this patch has no impact on any of the
regressions. Hence, there was never any NACKs issued. In a follow-up
patch I would suggest changing the size of the bridge buffers set in
FSConfig.py to also test the situation where the bridge fills up.
This patch fixes the checkpointing by ensuring that the directory is
passer to the scriptCheckpoints function, and that the num_checkpoints
is not used before it is initialised.
This patch adds a --repeat-switch option that will enable repeat core
switching at a user defined period (set with --switch-freq option).
currently, a switch can only occur between like CPU types. inorder CPU
switching is not supported.
*note*
this patch simply allows a config that will perform repeat switching, it
does not fix drain/switchout functionality. if you run with repeat switching
you will hit assertion failures and/or your workload with hang or die.
This patch moves the code related to checkpointing from the run() function to
several different functions. The aim is to make the code more manageable. No
functionality changes are expected, but since the code is kind of unruly, it
is possible that some change might have creeped in.
This changes the way in which the cpu class while restoring from a checkpoint
is set. Earlier it was assumed if cpu type with which to restore is not same
as the cpu type with the which to run the simulation, then the checkpoint
should be restored with the atomic cpu. This assumption is being dropped. The
checkpoint can now be restored with any cpu type, the default being atomic cpu.
This patch changes the se and fs script to use the clock option and
not simply set the CPUs clock to 2 GHz. It also makes a minor change
to the assignment of the switch_cpus clock to allow different clocks.
1) Modifies Benchmarks.py to add support for Android ICS and BBench on Android ICS.
2) An rcS script is added for BBench on ICS.
3) Separates benchmark entries and rcS scripts for GB/ICS
4) Removes the debugging output from the existing BBench run script. These
print statements were used for debugging and they seemed to confuse users
into believing they should see some terminal output.
As status matrix, MIPS fs does not work. Hence, these options are not
required. Secondly, the function is setting param values for a CPU class.
This seems strange, should probably be done in a different way.
This patch introduces a class hierarchy of buses, a non-coherent one,
and a coherent one, splitting the existing bus functionality. By doing
so it also enables further specialisation of the two types of buses.
A non-coherent bus connects a number of non-snooping masters and
slaves, and routes the request and response packets based on the
address. The request packets issued by the master connected to a
non-coherent bus could still snoop in caches attached to a coherent
bus, as is the case with the I/O bus and memory bus in most system
configurations. No snoops will, however, reach any master on the
non-coherent bus itself. The non-coherent bus can be used as a
template for modelling PCI, PCIe, and non-coherent AMBA and OCP buses,
and is typically used for the I/O buses.
A coherent bus connects a number of (potentially) snooping masters and
slaves, and routes the request and response packets based on the
address, and also forwards all requests to the snoopers and deals with
the snoop responses. The coherent bus can be used as a template for
modelling QPI, HyperTransport, ACE and coherent OCP buses, and is
typically used for the L1-to-L2 buses and as the main system
interconnect.
The configuration scripts are updated to use a NoncoherentBus for all
peripheral and I/O buses.
A bit of minor tidying up has also been done.
--HG--
rename : src/mem/bus.cc => src/mem/coherent_bus.cc
rename : src/mem/bus.hh => src/mem/coherent_bus.hh
rename : src/mem/bus.cc => src/mem/noncoherent_bus.cc
rename : src/mem/bus.hh => src/mem/noncoherent_bus.hh
Added the options to Options.py for FS mode with backward compatibility. It is
good to provide an option to specify the disk image and the memory size from
command line since a lot of disk images are created to support different
benchmark suites as well as per user needs. Change in program also leads to
change in memory requirements. These options provide the interface to provide
both disk image and memory size from the command line and gives more
flexibility.
This patch removes the assumption on having on single instance of
PhysicalMemory, and enables a distributed memory where the individual
memories in the system are each responsible for a single contiguous
address range.
All memories inherit from an AbstractMemory that encompasses the basic
behaviuor of a random access memory, and provides untimed access
methods. What was previously called PhysicalMemory is now
SimpleMemory, and a subclass of AbstractMemory. All future types of
memory controllers should inherit from AbstractMemory.
To enable e.g. the atomic CPU and RubyPort to access the now
distributed memory, the system has a wrapper class, called
PhysicalMemory that is aware of all the memories in the system and
their associated address ranges. This class thus acts as an
infinitely-fast bus and performs address decoding for these "shortcut"
accesses. Each memory can specify that it should not be part of the
global address map (used e.g. by the functional memories by some
testers). Moreover, each memory can be configured to be reported to
the OS configuration table, useful for populating ATAG structures, and
any potential ACPI tables.
Checkpointing support currently assumes that all memories have the
same size and organisation when creating and resuming from the
checkpoint. A future patch will enable a more flexible
re-organisation.
--HG--
rename : src/mem/PhysicalMemory.py => src/mem/AbstractMemory.py
rename : src/mem/PhysicalMemory.py => src/mem/SimpleMemory.py
rename : src/mem/physical.cc => src/mem/abstract_mem.cc
rename : src/mem/physical.hh => src/mem/abstract_mem.hh
rename : src/mem/physical.cc => src/mem/simple_mem.cc
rename : src/mem/physical.hh => src/mem/simple_mem.hh
With recent changes to the memory system, a port cannot be assigned a peer
port twice. While making use of the Ruby memory system in FS mode, DMA
ports were assigned peer twice, once for the classic memory system
and once for the Ruby memory system. This patch removes this double
assignment of peer ports.
I am not too happy with the way options are added in files se.py and fs.py
currently. This patch moves all the options to the file Options.py, functions
from which are called when required.
Enables the CheckerCPU to be selected at runtime with the --checker option
from the configs/example/fs.py and configs/example/se.py configuration
files. Also merges with the SE/FS changes.
This patch merely removes the use of the num_cpus cache parameter
which no longer exists after the introduction of the masterIds. The
affected scripts fail when trying to set the parameter. Note that this
patch does not update the regression stats.
This patch classifies all ports in Python as either Master or Slave
and enforces a binding of master to slave. Conceptually, a master (such
as a CPU or DMA port) issues requests, and receives responses, and
conversely, a slave (such as a memory or a PIO device) receives
requests and sends back responses. Currently there is no
differentiation between coherent and non-coherent masters and slaves.
The classification as master/slave also involves splitting the dual
role port of the bus into a master and slave port and updating all the
system assembly scripts to use the appropriate port. Similarly, the
interrupt devices have to have their int_port split into a master and
slave port. The intdev and its children have minimal changes to
facilitate the extra port.
Note that this patch does not enforce any port typing in the C++
world, it merely ensures that the Python objects have a notion of the
port roles and are connected in an appropriate manner. This check is
carried when two ports are connected, e.g. bus.master =
memory.port. The following patches will make use of the
classifications and specialise the C++ ports into masters and slaves.
In preparation for the introduction of Master and Slave ports, this
patch removes the default port parameter in the Python port and thus
forces the argument list of the Port to contain only the
description. The drawback at this point is that the config port and
dma port of PCI and DMA devices have to be connected explicitly. This
is key for future diversification as the pio and config port are
slaves, but the dma port is a master.
This patch makes the bus bridge uni-directional and specialises the
bus ports to be a master port and a slave port. This greatly
simplifies the assumptions on both sides as either port only has to
deal with requests or responses. The following patches introduce the
notion of master and slave ports, and would not be possible without
this split of responsibilities.
In making the bridge unidirectional, the address range mechanism of
the bridge is also changed. For the cases where communication is
taking place both ways, an additional bridge is needed. This causes
issues with the existing mechanism, as the busses cannot determine
when to stop iterating the address updates from the two bridges. To
avoid this issue, and also greatly simplify the specification, the
bridge now has a fixed set of address ranges, specified at creation
time.
Port proxies are used to replace non-structural ports, and thus enable
all ports in the system to correspond to a structural entity. This has
the advantage of accessing memory through the normal memory subsystem
and thus allowing any constellation of distributed memories, address
maps, etc. Most accesses are done through the "system port" that is
used for loading binaries, debugging etc. For the entities that belong
to the CPU, e.g. threads and thread contexts, they wrap the CPU data
port in a port proxy.
The following replacements are made:
FunctionalPort > PortProxy
TranslatingPort > SETranslatingPortProxy
VirtualPort > FSTranslatingPortProxy
--HG--
rename : src/mem/vport.cc => src/mem/fs_translating_port_proxy.cc
rename : src/mem/vport.hh => src/mem/fs_translating_port_proxy.hh
rename : src/mem/translating_port.cc => src/mem/se_translating_port_proxy.cc
rename : src/mem/translating_port.hh => src/mem/se_translating_port_proxy.hh
Currently there is an assumption that restoration from a checkpoint will
happen by first restoring to an atomic CPU and then switching to a timing
CPU. This patch adds support for directly restoring to a timing CPU. It
adds a new option '--restore-with-cpu' which is used to specify the type
of CPU to which the checkpoint should be restored to. It defaults to
'atomic' which was the case before.
This patch adds a new option for cpu type. This option is of type 'choice'
which is similar to a C++ enum, except that it takes string values as
possible choices. Following options are being removed -- detailed, timing,
inorder.
--HG--
extra : rebase_source : 58885e2e8a88b6af8e6ff884a5922059dbb1a6cb
There are two lines in O3CPU.py that set the dcache and icache
tgts_per_mshr to 20, ignoring any pre-configured value of tgts_per_mshr.
This patch removes these hardcoded lines from O3CPU.py and sets the default
L1 cache mshr targets to 20.
--HG--
extra : rebase_source : 6f92d950e90496a3102967442814e97dc84db08b
A significant contributor to the need for adoptOrphanParams()
is the practice of appending to SimObjectVectors which have
already been assigned as children. This practice sidesteps the
assignment operation for those appended SimObjects, which is
where parent/child relationships are typically established.
This patch reworks the config scripts that use append() on
SimObjectVectors, which all happen to be in the x86 system
configuration. At some point in the future, I hope to make
SimObjectVectors immutable (by deriving from tuple rather than
list), at which time this patch will be necessary for correct
operation. For now, it just avoids some of the warning
messages that get printed in adoptOrphanParams().
Frame buffer and boot linux:
./build/ARM_FS/m5.opt configs/example/fs.py --benchmark=ArmLinuxFrameBuf --kernel=vmlinux.touchkit
Linux from a CF card:
./build/ARM_FS/m5.opt configs/example/fs.py --benchmark=ArmLinuxCflash --kernel=vmlinux.touchkit
Run Android
./build/ARM_FS/m5.opt configs/example/fs.py --benchmark=ArmAndroid --kernel=vmlinux.android
Run MP
./build/ARM_FS/m5.opt configs/example/fs.py --benchmark=ArmLinuxCflash --kernel=vmlinux.mp-2.6.38
This patch moves the assignment of testsys.switch_cpus, testsys.switch_cpus_1,
switch_cpu_list, and switch_cpu_list1 outside of the for loop so they are
assigned only once, after switch_cpus and switch_cpus_1 are constructed.
This change fixes the problem for all the cases we actively use. If you want to try
more creative I/O device attachments (E.g. sharing an L2), this won't work. You
would need another level of caching between the I/O device and the cache
(which you actually need anyway with our current code to make sure writes
propagate). This is required so that you can mark the cache in between as
top level and it won't try to send ownership of a block to the I/O device.
Asserts have been added that should catch any issues.
makeArmSystem creates both bare-metal and Linux systems more cleanly.
machine_type was never optional though listed as an optional argument; a system
such as "RealView_PBX" must now be explicitly specified. Now that it is a
required argument, the placement of the arguments has changed slightly
requiring some changes to calls that create ARM systems.
It's confusing (especially to new users), when you are setting some standard
parameters (as defined in Options.py) and they aren't reflected in the simulations
so we might as well link the settings in CacheConfig.py to those in Options.py
This way things that don't care about work count options and/or aren't called
by something that has those command line options set up doesn't have to build
a fake object to carry in inert values.
This makes sure that the address ranges requested for caches and uncached ports
don't conflict with each other, and that accesses which are always uncached
(message signaled interrupts for instance) don't waste time passing through
caches.
The disk image to use was always being forced to a particular value. This
change changes what disk image is selected as the default based on the
architecture being built. In the future, a more sophisticated system might be
used that selected a path based on certain rules instead of relying on one off
file names.
Most of the messages in the config scripts that report a time value already
print "@ tick" followed by the current tick value, but a few were printing
"@ cycle". Since this is a distinction that's frequently confusing to new
users, this changes those message to the more accurate and consistent "@ tick".
The previous slower ruby latencies created a mismatch between the faster M5
cpu models and the much slower ruby memory system. Specifically smp
interrupts were much slower and infrequent, as well as cpus moving in and out
of spin locks. The result was many cpus were idle for large periods of time.
These changes fix the latency mismatch.
The separate restoreCheckpoint() call is gone; just pass
the checkpoint dir as an optional arg to instantiate().
This change is a precursor to some more extensive
reworking of the startup code.
Enforce that the Python Root SimObject is instantiated only
once. The C++ Root object already panics if more than one is
created. This change avoids the need to track what the root
object is, since it's available from Root.getInstance() (if it
exists). It's now redundant to have the user pass the root
object to functions like instantiate(), checkpoint(), and
restoreCheckpoint(), so that arg is gone. Users who use
configs/common/Simulate.py should not notice.
Most of these frontend configurations share cache configuration code, pull it out so that
changes to caches don't have to require changing multiple config files.
Reorganized ruby python configuration so that protocol and ruby memory system
configuration code can be shared by multiple front-end configuration files
(i.e. memory tester, full system, and hopefully the regression tester). This
code works for memory tester, but have not tested fs mode.
Connects M5 cpu and dma ports directly to ruby sequencers and dma
sequencers. Rubymem also includes a pio port so that pio requests
and be forwarded to a special pio bus connecting to device pio
ports.
Get rid of misc.py and just stick misc things in __init__.py
Move utility functions out of SCons files and into m5.util
Move utility type stuff from m5/__init__.py to m5/util/__init__.py
Remove buildEnv from m5 and allow access only from m5.defines
Rename AddToPath to addToPath while we're moving it to m5.util
Rename read_command to readCommand while we're moving it
Rename compare_versions to compareVersions while we're moving it.
--HG--
rename : src/python/m5/convert.py => src/python/m5/util/convert.py
rename : src/python/m5/smartdict.py => src/python/m5/util/smartdict.py
-option to allow threads to run to a max_inst_any_thread which is more useful/quicker in a lot of
cases then always having to figure out what tick to run your simulation to.
this was double scheduling itself (once in constructor and once in cpu code). also add support for stopping / starting
progress events through repeatEvent flag and also changing the interval of the progress event as well
Previously there was one per bus, which caused some coherence problems
when more than one decided to respond. Now there is just one on
the main memory bus. The default bus responder on all other buses
is now the downstream cache's cpu_side port. Caches no longer need
to do address range filtering; instead, we just have a simple flag
to prevent snoops from propagating to the I/O bus.
