Adjust the traffic generator time-out so that the script works out of
the box
Change-Id: I6b3b6b11f98b094ae3acdbe09488c26e4aeb0ab4
Reviewed-by: Andreas Sandberg <andreas.sandberg@arm.com>
This patch adds a config script that broadly replicates the behaviour
of lat_mem_rd. The test is based on traffic generators, and as such we
simply randomise addresses in increasingly large ranges, and play them
back using the trace functionality of the traffic generator.
The test script is accompanied by a post-processing and visualisation
script. At the moment no configurability is added to tweak the memory
hierarchy, but a follow on patch could easily extend the
functionality.
This patch adds changes to the configuration scripts to support elastic
tracing and replay.
The patch adds a command line option to enable elastic tracing in SE mode
and FS mode. When enabled the Elastic Trace cpu probe is attached to O3CPU
and a few O3 CPU parameters are tuned. The Elastic Trace probe writes out
both instruction fetch and data dependency traces. The patch also enables
configuring the TraceCPU to replay traces using the SE and FS script.
The replay run is designed to resume from checkpoint using atomic cpu to
restore state keeping it consistent with FS run flow. It then switches to
TraceCPU to replay the input traces.
This patch introduces a few subclasses to the CoherentXBar and
NoncoherentXBar to distinguish the different uses in the system. We
use the crossbar in a wide range of places: interfacing cores to the
L2, as a system interconnect, connecting I/O and peripherals,
etc. Needless to say, these crossbars have very different performance,
and the clock frequency alone is not enough to distinguish these
scenarios.
Instead of trying to capture every possible case, this patch
introduces dedicated subclasses for the three primary use-cases:
L2XBar, SystemXBar and IOXbar. More can be added if needed, and the
defaults can be overridden.
This patch changes the name of the Bus classes to XBar to better
reflect the actual timing behaviour. The actual instances in the
config scripts are not renamed, and remain as e.g. iobus or membus.
As part of this renaming, the code has also been clean up slightly,
making use of range-based for loops and tidying up some comments. The
only changes outside the bus/crossbar code is due to the delay
variables in the packet.
--HG--
rename : src/mem/Bus.py => src/mem/XBar.py
rename : src/mem/coherent_bus.cc => src/mem/coherent_xbar.cc
rename : src/mem/coherent_bus.hh => src/mem/coherent_xbar.hh
rename : src/mem/noncoherent_bus.cc => src/mem/noncoherent_xbar.cc
rename : src/mem/noncoherent_bus.hh => src/mem/noncoherent_xbar.hh
rename : src/mem/bus.cc => src/mem/xbar.cc
rename : src/mem/bus.hh => src/mem/xbar.hh
Add new DRAM_ROTATE mode to traffic generator.
This mode will generate DRAM traffic that rotates across
banks per rank, command types, and ranks per channel
The looping order is illustrated below:
for (ranks per channel)
for (command types)
for (banks per rank)
// Generate DRAM Command Series
This patch also adds the read percentage as an input argument to the
DRAM sweep script. If the simulated read percentage is 0 or 100, the
middle for loop does not generate additional commands. This loop is
used only when the read percentage is set to 50, in which case the
middle loop will toggle between read and write commands.
Modified sweep.py script, which generates DRAM traffic.
Added input arguments and support for new DRAM_ROTATE mode.
The script now has input arguments for:
1) Read percentage
2) Number of ranks
3) Address mapping
4) Traffic generator mode (DRAM or DRAM_ROTATE)
The default values are:
100% reads, 1 rank, RoRaBaCoCh address mapping, and DRAM traffic gen mode
For the DRAM traffic mode, added multi-rank support.
This patch adds basic functionality to quickly visualise the output
from the DRAM efficiency script. There are some unfortunate hacks
needed to communicate the needed information from one script to the
other, and we fall back on (ab)using the simout to do this.
As part of this patch we also trim the efficiency sweep to stop at 512
bytes as this should be sufficient for all forseeable DRAMs.
This patch bumps the bus clock speed such that the interconnect does
not become a bottleneck with a DDR4-2400-x64 DRAM delivering 19.2
GByte/s theoretical max.
This patch renames the not-so-simple SimpleDRAM to a more suitable
DRAMCtrl. The name change is intended to ensure that we do not send
the wrong message (although the "simple" in SimpleDRAM was originally
intended as in cleverly simple, or elegant).
As the DRAM controller modelling work is being presented at ISPASS'14
our hope is that a broader audience will use the model in the future.
--HG--
rename : src/mem/SimpleDRAM.py => src/mem/DRAMCtrl.py
rename : src/mem/simple_dram.cc => src/mem/dram_ctrl.cc
rename : src/mem/simple_dram.hh => src/mem/dram_ctrl.hh
This patch adds a configuration that simplifies evaluation of DRAM
controller configurations by automating a sweep of stride size and
bank parallelism. It works in a rather unconventional way, as it needs
to print the traffic generator stimuli based on the memory
organisation. Hence, it starts by configuring the memory, then it
prints a traffic-generator config file, and loads it.
The resulting stats have one period per data point, identified by the
stride size, and the number of banks being used.
